Cisco Wireless :: WLC 7.0.98.0 / How To Convert Snmp Trap To Be Syslog Message
Aug 22, 2011
Now I'm trying to write software that get information from Syslog message, but I'm facing with the problem about getting statistic of client de-authenticated in a WLC (Software Version: 7.0.98.0), because I cannot find any log about this information on WLC except only this SNMP trap:
Tue Aug 23 09:52:28 2011Client Deauthenticated: MACAddress:00:xx:77:2c:06:db Base Radio MAC:00:xx:5d:0c:fc:30 Slot: 0 User Name: unknown Ip Address: 10.2xx.47.15 Reason:Unspecified ReasonCode: 1
So, is there any way that I can configure WLC to convert this SNMP trap to send to Syslog server as a normal Syslog message?
View 2 Replies
ADVERTISEMENT
Mar 30, 2013
how to enable snmp traps for syslog message in Cisco Nexus platform ?
Mean what would be equivalent CLI for the below
"snmp-server enable traps syslog"
View 2 Replies
View Related
Feb 21, 2012
I want to be able to send snmp traps to my NMS alerting our NOC to when we reach our configured max-associations on an ap. We currently use both 1130 AG and 1140-2N in autonomous mode, no controller. I have found a debug command "debug dot11 station connection failure" and the output of a test AP shows us the fact that the maximum number was reached. I need to find if it is possible to trap on such information.
View 1 Replies
View Related
Jul 1, 2011
send me step by step guide of how to configure SNP server for SNMp trap
View 2 Replies
View Related
Feb 1, 2012
Upgraded LMS to 4.1. Yep basically reinstalled. However I can't remember how I did a couple of thing on the original system.
I am trying to take the traps from the Cisco equipment to the LMS and generate e-mail. How do I take the incoming traps (Crit and Warning) and send an e-mail alarm. I'll plan to control what to trap on at the Cisco Equipment.
SNMP trap is set from a fan fault, the Cisco send a trap to the LMS. Now I want take that trap and forward via an email.
I have been reading the admin documentation on "Notification and Action Setting". I see how to take the Cisco LMS created trap and email alarm. (In this case I need a specific trap that LMS did not have.) I see how to take Cisco Traps and resend them to other NMS.
View 1 Replies
View Related
Dec 7, 2012
We are implementing fault management tool and for that we need information such as what type of traps are being triggered by router on what events..currently we have BGP, interface,reachability,h/w,syslog,authfail,config, trap types configured..All these are hitting in our fm tool but I need to know when these traps are being triggered by router.more importantly authfail, config, syslog, bgp.
View 4 Replies
View Related
Nov 22, 2011
I want to make my switch send trap when failed SSH login is detected. I found the "login Enhancement" feature and enabled the trap and logging for the failed attempt.
3750# sh run | in login
aaa authentication login default local
login delay 1
[Code].....
View 7 Replies
View Related
Apr 16, 2012
Below is my config for IP SLA. I would like a SNMP trap to be sent when my primary fails over to my secondary and so on.
sla monitor 20
type echo protocol ipIcmpEcho 100.X.X.1 interface INET-FIOS150
num-packets 2
[Code].....
View 4 Replies
View Related
Jun 20, 2012
I am in the process of testing VA5(1.2) version of ACE on ACE4710 appliance.I did redundnacy configuration and it is working fine.I have done the snmp configuration and SNMP trap receiver is able to recieve traps like link up/down, so it proves that SNMP configuration is working fine, but i am not able to generate the SNMP trap notification for "clrRedundancyStateChange".I tried two things:
1) Via CLI, ran the command "ft switchover all" and i could see redundancy state changes.
2) Powered down Active 4710 appliance and standby ACE 4710 appliance taking over as Active.
However, none of the above could generate the trap clrRedundancyStateChange. how this trap can be generated? In snmp-server enable traps commands doesn't have any option for enabling FT related traps.
View 1 Replies
View Related
Apr 9, 2011
How to prepare my network for snmp,currently i don't have SNMP configured with community,so what is the requirement for that?what server i need to configure in order to receive SNMP traps coz last time i had issue ,one of my tunnels (terminated on asa 5510) goes down for 2 hours and i didn't realized that
View 7 Replies
View Related
Jan 25, 2011
I use SNMP and I dont have access to a router to test.Can the SNMP Trap to: Field in the SMNP section be configured for multiple IP addresses.?
View 1 Replies
View Related
Sep 10, 2012
I have Cisco 2960's, 3750's and 3750x's all running IOS on the access layer. I have Cisco 6504's running IOS on the Distribution and Core layers. I am looking to monitor redundant links through Spectrum by having specific ports send traps but I have run into trouble finding how to configure it. I would like to have:
1. Logging enabled for all links (Fiber and Copper) so that I see all links up/down messages in the syslog
2. SNMP traps sent for linkup/link down messages only for redundant links (ex. Dual Up links from Access Layer or Redundant Ether channel Links on Dist Layer)
3. SNMP traps should be ignored/not sent for all copper ports.
View 3 Replies
View Related
Dec 17, 2012
I have a snmp trap sent every 30 seconds from one of my cisco switches (a stack of 3750 to be precise): ccStatusMemberStatusChange. Do you know what it is and why it is sent continuously?
View 1 Replies
View Related
Feb 6, 2013
We have two ACE4710 in a failover configuration with Software version A4(2.0). SNMP is setup and the receiver is able to receive SNMP traps.The issue is we are receiving a linkDown trap notification at least once every other day, followed shortly by a linkUp notification a minute later. We have checked all layer 2 devices connected to the ACE and cannot see any evidence that any link actually disconnected. We experienced no traffic lost, but this could be because a couple of the ACE links are bundled. The trap notification does not actually indicate which interface changed status. All links are Gigabits, and there are no packet drops either on the ACE or the layer 2 switch.
View 3 Replies
View Related
Sep 16, 2012
It is a Customer requirement to send 802.11 client association/disassociation logs to the Syslog server in a Unified Wireless system. (AIR-CT5508 + LAP1142) [code] Unfortunately I didn't find such logs even in Msg Log with the severity level set to debugging.I was able to do client assoc/disassoc logging with SNMP trap + trap receiver software, BUT is there any way to do this with Syslog?
View 1 Replies
View Related
Nov 12, 2011
I received a syslog message on my cisco 3845 router, what is that message mean. 11 13:36:06.265 UTC: ASSERTION FAILED: file "../les/if_ng_dslsar_tx.c", line 385
View 2 Replies
View Related
Apr 3, 2008
I am only able to get InfoAlarm messages sent to via email notifications.My switch is sending logs to Cisco Works.Example:
13. 10.10.0.1 10.10.0.1 Apr 04 2008 10:34:41 EC 5 UNBUNDLE Interface GigabitEthernet1/4 left the port-channel Port-channel2 *
14. 10.10.0.1 10.10.0.1 Apr 04 2008 10:34:41 EC 5 BUNDLE Interface GigabitEthernet1/4 joined port-channel Port-channel2
But I only recieve infoalarm messages:
ALERT ID = 00000UE
TIME = Fri 04-Apr-2008 11:04:00 PST
STATUS = Active
SEVERITY = Informational
MANAGED OBJECT = 10.10.0.1
MANAGED OBJECT TYPE = Switches and Hubs
EVENT DESCRIPTION = 10.10.0.1: Cisco Configuration Management Trap:InformAlarm; 10.10.0.1: Authentication Failure:MinorAlarm;
My switch is setup as:
logging source-interface Loopback0
logging 10.10.100.111
snmp-server enable traps bridge newroot topologychange
snmp-server enable traps syslog
I do not recieve critical or warning syslog messages.
View 9 Replies
View Related
Sep 15, 2009
We have 2 Cat 6509 connected to 1 Gbps Ethernet WAN Link. On each 6509 we use 2 Gbps IPSec SPA Encryption cards for Encryption. The encrypted traffic goes to a GRE Tunnel. This morning I found some error messages in syslog.
%CONST_DIAG-SP-3-HM_TEST_FAIL: Module 1 TestIPSecEncrypDecrypPkt consecutive failure count:2
There were also several short tunnel downs/ups. I wonder if there is a bug in the new IOS image 12.2(33)SXI2a. We upgraded to this image last weekend.
View 2 Replies
View Related
Jul 27, 2011
I want to use an EEM applet on a Cisco IOS 2431 voice gateway running 15.1(2)T to take action upon expiration of a SIP registration (with its sip registrar). I thought that it might be possible to use existing error messages generated by the ios sip application to trigger an EEM applet.Is there a reference that lists all SYSLOG messages that SIP can generates, and their error levels? Can you show me how to turn on syslog messages, so that I can cause a SIP registration expiration on my GW and then see what SYSLOG messages are produced?
I think I understand how to write an applet and its event trigger from a SYSLOG message pattern, but I am having trouble seeing any SIP error messages at all, except if I turn on Debug, which usually produces way too many messages and may impact performance.
View 1 Replies
View Related
Dec 19, 2011
I keep getting an error message, i've tried several things to resolve it but still no success.This is the exact error message:
regular translation creation failed for protocol 41 src Customer: dst outside:
View 4 Replies
View Related
Mar 5, 2012
I'm fine tuning some of our ASA logging config, and am having an issue with one particular syslog ID.The message is: syslog 106100: default-level informational (enabled)and the log settings are:
Syslog logging: enabled
Facility: 20
Timestamp logging: enabled
Standby logging: disabled
Debug-trace logging: disabled
[code]....
This ACE log entry is generated by explicit deny any any statements at the end of all the ACLs, e.g.access-list inside_access_in extended deny ip any any log interval 600 Based on the config, I would expect to see this being logged to the syslog server, but not to the local buffer, but am still seeing them locally in the buffer:
Feb 22 2012 10:58:20: %ASA-4-106100: access-list inside_access_in denied udp INSIDE/HOSTABC(52629) -> OUTSIDE/HOSTXXX(162) hit-cnt 5 300-second interval [0x3baecf1e, 0x0]
It also still shows these as level "warning", %ASA-4-106100, instead of the default %ASA-6-106100 I've tried removing and re-applying the config at different levels but it still reports in the buffer log as level "warning", %ASA-4-106100 This also doesnt affect every 106100 log that is generated. Most messages are generated at the correct level 6 severity but some seem to randomly log at level 4. There doesn't seem to be any pattern to this. The same access-list line can produce severity level 4 and 6 106100 messages.
View 2 Replies
View Related
Feb 23, 2011
Receiving the following syslog message from a 4402 WLC:
%CAPWAP-3-AP_DB_ALLOC: capwap_ac_db.c:145
Unable to allot AP entry in database. We receive this message about once a minute on average. I can't find any documentation saying what it is. It looks like a database error, which makes think it might be a memory issue or an issue with having too many AP's on the WLC. However, that controller has less than 30 AP's on it.
View 3 Replies
View Related
Sep 21, 2012
logging buffered 4096 warnings The above causes router to log all the events with severity level 4 or below in buffer.What about logging console warnings command?will the above command cause router to send log messages with severity level 4( warnings severity level) to console only or will the router send all the log messages with severity level 4 or below to console ?
View 3 Replies
View Related
Oct 8, 2011
I recently upgraded a few 2960 switches to 15.0(1)SE, and while they are working fine, I did notice a strange syslog message upon boot-up that wasn't previously there. [code] I did some cursory searching via google but nothing useful presented itself.
View 7 Replies
View Related
Jul 2, 2012
Query is, Can i send my syslog messages to SNMP sever? if so, what command needs to be enabled on nexus 7k?
View 3 Replies
View Related
Aug 6, 2012
I have a pair of 3750E-24PD-S stacked together, it seems after stacked together the stacked switch always flood the console screen with these messages which are not true: [code] Switch-2 is the stack member, Switch-1 is the stack master. The RPS fan failed refers to RPS2300 or the internal power supply of 3750E? Even when I turned on the RPS2300 the stacked switch still display the messages. Also I have two RPS2300 serving stack master and stack member respectively both RPS2300 were switched off why the messages only refer to Switch-2 and not Switch-1? [code]
View 1 Replies
View Related
Feb 22, 2013
I have cisco 5550 Firewall, one messages appear in syslog server from Firewall, (warning) i want to stop this message from appearing syslog traps.
View 2 Replies
View Related
Jul 7, 2012
Add the ability to send syslog events to multiple syslog servers in the SA500 Series routers. I know the functionality is currently in the RV220W because we utilized it. It would be great if you could configure the syslog servers by event type as well. For example, being able to send the kernel events to syslog server A, and all other events to syslog server B.
View 0 Replies
View Related
Jan 15, 2012
Recently i have upgraded the IOS of ASA5550 (in HA mode) to 8.4.2 from 8.0.5, after OS upgrade we found that the syslog from thses firewalls are not getting captured/transfered to centralised syslog server. The server is reachable from the firewalls.
View 3 Replies
View Related
Nov 25, 2011
Is it possible to have the ASA send an SNMP trap when a particular bit-rate over an interface is exceeded?
View 2 Replies
View Related
Dec 3, 2012
I have a 5508 wireless lan controller we have two SSID configured Profile Name : Corporate and Guest When I go look at the Most Recent Traps all I see is Client with Mac address blah has joined your corporate, this goes on for sometime. But I am unable to see any of the Guest logs joining the network, I have since then grabbed my laptop and connected to the guest log. I still dont see any logs in Most Recent Traps for the Guest SSID WLAN configuration, I then blocked my Mac address and tried to connect again, No logs. I need to also montior the guest network is there some special tick box I need to apply for this to work? Once the guest is connected I can view them in the clients list but it never shows them on MOST RECENT TRAPS but I want to see the guests account connecting or failing to connect as we currently have a rogue device annoying me.
View 3 Replies
View Related
Jan 7, 2013
Which trap we need to enable to monitor FEX module on 5K.If FEX goes down due to link failure/power down we do not receive any trap on SNMP server. Ethernet1/5 is where Fex module in connected on 5K
Some sample log
2013 Jan 4 12:11:32switch1 %FEX-5-FEX_PORT_STATUS_NOTI: Uplink-ID 1 of Fex 103 that is connected with Ethernet1/5 changed
its status from Connecting to Active
2013 Jan 4 12:11:32switch1 %ETH_PORT_CHANNEL-5-PORT_UP: port-channel103: Ethernet1/5 is up
2013 Jan 4 12:11:32switch1 %ETH_PORT_CHANNEL-5-FOP_CHANGED: port-channel103: first operational port changed from none to E
thernet1/5
[code]....
View 1 Replies
View Related
Oct 10, 2012
As part of troubleshooting a seperate issue, somebody on my 891 router had set logging trap debugging which shows as a line in sh run just above the access-lists. There is no syslog server however so I'd like to remove this entry, however when I do no logging trap debugging I end up with a no logging trap entry replacing the previous logging trap debugging entry. Is there away to be rid of this entry? I tried no no logging trap but of course that's an invalid command.
View 6 Replies
View Related
