Cisco VPN :: Configure Static IP Address In Remote Client ASA 5500?

Aug 13, 2011

i am trying to configure static ip on remote client user side , i am using the following doc as an example but i am not getting the ip which i am mentiong in the user .[url]...

View 10 Replies


ADVERTISEMENT

Cisco VPN :: ACS 5.2 Create Static IP Address User For Remote Access

Sep 15, 2011

At first I use ACS 4.2 to create static ip address user for remote access VPN,It's easy,just configuration it at user set>Client IP Address Assignment>Assign static IP address,but when I use ACS 5.2 I can't find it.I try to add IPv4 address attribute to user by read "ACS 5.2 user guide" ,it says this: [code] I do this,but it's not work.When I use EasyVPN client to connect ASA 5520,user could through authentication but will not get that static IP address which I configuration on Internal Users.so,what should I do,if anyboby knows how to use ACS 5.2 to create a static ip address user for remote access VPN.

View 2 Replies View Related

Cisco VPN :: 1921 Loop Back Interface / Static IP Address For Client

Nov 17, 2012

I have a couple a questions answers on which i cant google for a period. BTW maybe i simly use wrong aproach to choose keywords.

1)  Is it possible to assign same ip address to the same client each time  it authenticated, preferably without using DHCP? Im definely sure that  it possible but cant find corresponded configuration examples (my device  is Cisco 1921 with IOS 15.0.1).
 
2)  Is it possible to assign dynamic crypto map to loopback interface (the  purpose to make EASY VPN Server accessible through two interfaces -  maybe you recommend other approach instead?) - as i move workingcrypto  map from phy int to loopback - i cant connect with reason "Phace1 SA  policy proposal not accepted"

View 3 Replies View Related

Cisco AAA/Identity/Nac :: Use ACS 5.2 To Create Static IP Address User For Remote Access VPN

Sep 17, 2011

At first I use ACS 4.2 to create static ip address user for remote access VPN,It's easy,just configuration it at user set>Client IP Address Assignment>Assign static IP address,but when I use ACS 5.2 I dont't know how to do it.
 
I try to add IPv4 address attribute to user by read "ACS 5.2 user guide" ,it says this:
    
     Step 1Add a static IP attribute to internal user attribute dictionary:
     Step 2Select System Administration > Configuration > Dictionaries > Identity > Internal Users.
     Step 3Click Create.
     Step 4Add static IP attribute.
     Step 5Select Users and Identity Stores > Internal Identity Stores > Users.
     Step 6Click Create.
     Step 7Edit the static IP attribute of the user.
 
     I just do it,but it's not work.When I use EasyVPN client to connect ASA 5520,user could success to authentication but will not get the static IP address which I configure on Internal Users,so the tunnel set up failed.I try to Configure a IP pool on ASA for ACS users get IP address,and use EasyVPN client to connect ASA , everything is OK,user authenticate successed.but when I kill IP pool coufigurations and use the  "add a static IP address to user "configurations,EzVPN are failed. how to use ACS 5.2 to create a static ip address user for remote access VPN?

View 7 Replies View Related

Cisco WAN :: Configure 861 Router For Internet Using Static Ip Address?

Apr 5, 2013

I am having a cisco 861 series router.The Cable from the isp was connected to fastethernet4(wan port)
 
Following are my isp details
IP address:172.16.62.130
subnet:255.255.0.0
default gate way:172.16.62.1
dns primary:202.153.32.2
secondary:202.153.32.3
 
How do i configure this details in the router and access the internet in my devices.
 
i want the network to be in 192.168.1.0 to 254.
 
how do i configure my router with this details using cisco configuration professional

View 1 Replies View Related

Cisco Routers :: Configure SRP527w Without Static Outside Ip Address

Jul 17, 2010

I need to know how to configure SRP527w  without a static outside  ip address to establish a VPN tunnel with VPNC3000.

View 31 Replies View Related

Cisco VPN :: Configure ASA5505 For Remote User Using EasyVPN Client?

Jul 5, 2011

I need to configure our ASA5505 firewall for remote access to our network using EasyVPN software installed on a laptop. That laptop will be connected in the different places, using DSL or 3G toggle or Public Wi-Fi. For some people it's very easy, but I don't have any experience with firewalls.

View 9 Replies View Related

DHCP Configuration To Provide Address For Remote VPN Client?

Mar 17, 2011

I have DHCP server running in windows 2003. Presently its unable to provide Ip address for VPN clients who connect remotely. What I should do / reconfigure in DHCP, so that the DHCP server provides address for VPN clients.

View 4 Replies View Related

Cisco VPN :: ASA5510 Remote IPSEC Client Not Using Dedicated IP Address

Aug 8, 2011

i am just installing my ASA 5510 and i want to configure it for remote access VPN IPSEC client.i use this doc : URl,When i start the connexion, the Client uses the first address of the pool and not the dedicated address ?,i have forget something ?

View 2 Replies View Related

Cisco Routers :: Configure RV082 Router With Mac Native VPN Client For Remote Access

Oct 9, 2012

I am trying to configure RV082 router with Mac Native VPN Client for my remote access. However, no matter what I did, I am not able to make it works. Can any one can give me an example of how to conguration my RV082 router and Mac Book Pro(Mountain Lion)?

View 2 Replies View Related

Cisco VPN :: All Remote Wireless IPSec Remote Clients Fail Connecting To ASA 5500

Sep 12, 2012

We have two ASA 5500 series Firewalls running 8.4(1).  One in New York, another in Atlanta.They are configured identically for simple IPSecV1 remote access for clients.  Authentication is performed by an Radius server local to each site.
 
There are multiple IPSec Site-to-Site tunnels on these ASA's as well but those are not affected by the issues we're having.First, let me start with the famous last words, NOTHING WAS CHANGED.
 
All of a sudden, we were getting reports of remote users to the Atlanta ASA timing out when trying to bring up the tunnel.  They would get prompted for their ID/Password, then nothing until it times out.Sames users going to the NY ASA are fine.After extensive troubleshooting, here is what I've discovered. Remote clients will authenticate fine to the Atlanta Firewall ONLY IF THEY ARE USING A WIRED CONNECTION.
 
If they are using the wireless adapter for their client machine, they will get stuck trying to login to Atlanta.These same clients will get into the New York ASA with no problems using wired or wireless connections.Windows 7 clients use the Shrewsoft VPN client and Mac clients use the Cisco VPN client.  They BOTH BEHAVE the same way and fail to connect to the Atlanta ASA if they use their wireless adapter to initiate the connection.
 
Using myself as an example.
 
1. On my home Win 7 laptop using wireless, I can connect to the NY ASA with no issues. 
 
2. The same creditials USED to work for Atlanta as well but have now stopped working.  I get stuck until it times out.
 
3. I run a wire from my laptop to the FiOS router, then try again using the same credentials to Atlanta and I get RIGHT IN.
 
This makes absolutely no sense to me.  Why would the far end of the cloud care if I have a wired or wireless network adapter?  I should just be an IP address right?  Again, this is beyond my scope of knowledge.We've rebuilt and moved the Radius server to another host in Atlanta in our attempts to troubleshoot to no avail.  We've also rebooted the Atlanta Firewall and nothing changed.
 
We've tried all sorts of remote client combinations.  Wireless Internet access points from different carriers (Clear, Verizon, Sprint) all exhibit the same behavior.  Once I plug the laptops into a wired connection, BAM, they work connecting to Atlanta.  The New York ASA is fine for wired and wireless connections.  Same with some other remote office locations that we have.
 
Below I've detailed the syslog sequence on the Atlanta ASA for both a working wired remote connection and a failed wireless connection.  At first we thought the AAA/Radius server was rejecting us but is shows the same reject message for the working connection.  Again, both MAC and Windows clients show the same sequence.Where the connection fails is the "IKE Phase 1" process.

-------------------------------------------------------------------------------------------------------------------------
WORKING CONNECTION
-------------------------------------------------------------------------------------------------------------------------
 %ASA-6-713172: Automatic NAT Detection Status: Remote end is|is not behind a NAT device This end is|is not behind a NAT device
NAT-Traversal auto-detected NAT.
 %ASA-6-113004: AAA user aaa_type Successful: server = server_IP_address, User = user
 %ASA-6-113005: AAA user authentication Rejected: reason = string: server = server_IP_address, User = user

[code]...

View 1 Replies View Related

Cisco Firewall :: ASA 5500 Static Dhcp Binding?

Sep 30, 2011

Can the DHCP server on an ASA be configured with static bindings like IOS routers can?

View 2 Replies View Related

Cisco VPN :: VPN Client Traffic Through ASA 5500?

Feb 10, 2011

I have been trying to conect a Cisco VPN client through an ASA and it makes the connection but doesn't allow any traffic through. The ASA does have a site to site VPN attached to the outside interface.I suppose the first question is it possible to allow VPN client to connect through an ASA 5500 from the inside network when there are Site to Site VPN's already attached to the outside interfaces?If possible then what have I missed. I have tried adding NAT exempt for the traffic between the internal networks and "an IPSEC pass thru Inspect Map".

View 4 Replies View Related

Cisco VPN :: Restrict The Remote Access To ASA 5500?

Oct 20, 2012

is it possible to  restrict the Remote  Access VPN to  ASA based on the Source  Public IP , if so  how ?
 
here I am not talking about the  VPN-Filter under group-policy . I Want to restrict the access from specified source  IP  (  Public IP)

View 1 Replies View Related

Cisco VPN :: ASA 5500 - Remote Access VPN Intermittent Disconnect

Oct 11, 2012

I am having the peculiar issue in our ASA5500 firewall (version 8.2(5) ), where the remote access vpn is getting issue, I am unable to ping the internal resource for sometime, however without any modification the problem gets resolves.
 
During the issue we can see Tx count 0
 
Username     : xxxxxx              Index        : 3147
Assigned IP  : 172.17.254.24          Public IP    : 14.99.x.x
Protocol     : IKE IPsec
License      : IPsec
Encryption   : 3DES AES128            Hashing      : SHA1
Bytes Tx     : 0                      Bytes Rx     : 8764
Group Policy : EMP-VPN            Tunnel Group : EMP-VPN
Login Time   : 15:07:51 IST Fri Oct 12 2012
Duration     : 0h:06m:34s
Inactivity   : 0h:00m:00s
NAC Result   : Unknown
VLAN Mapping : N/A                    VLAN         : none

View 2 Replies View Related

Cisco Switching/Routing :: WLC 5500 Controller And Client Connectivity

Nov 20, 2012

Having an issue with my WLC 5500 and client connectivity. This just started today. Clients will connect for a short period of time and then drop off. WLC appears fine with the exception of a bunch of trap errors. I've rebooted the WLC but this did not clear the issue.

View 3 Replies View Related

Cisco Wireless :: Client Association Syslog Message With 5500 Wlc

Sep 16, 2012

It is a Customer requirement to send 802.11 client association/disassociation logs to the Syslog server in a Unified Wireless system. (AIR-CT5508 + LAP1142) [code] Unfortunately I didn't find such logs even in Msg Log with the severity level set to debugging.I was able to do client assoc/disassoc logging with SNMP trap + trap receiver software, BUT is there any way to do this with Syslog?

View 1 Replies View Related

Cisco Wireless :: Migration Of Remote Location APs (4400 To 5500)

Jan 7, 2013

I have a existing wireless setup of 4400 WLC with some  AP's  connected remotely,now i am migrating the whole setup to the new WLC 5500. All the AP has been registered to the new WLC 5500 except the remote location AP's.As there was no option of giving IP address in GUI of the controller in 4400 WLC, i have changed the controller name and restarted the AP, but even though it is going back to the old controller.

View 15 Replies View Related

Cisco Wireless :: Client Type In 5500 Series WLAN Controller

Jul 5, 2011

The Release Notes for 7.0.116.0 of WLC 5500 has a table which title is "Client Type", and it shows wireless adapters. My question is,
what kind of customer means? Wireless clients or clients for an specific application? If it was the first option, does it mean tha just this adapters could connect to my wireless network?

View 1 Replies View Related

Cisco Security :: To Restrict Remote Access VPN To ASA 5500 Based On Source

Oct 20, 2012

Is it possible to  restrict the Remote  Access VPN to  ASA based on the Source  Public IP , if so  how ? here I am not talking about the  VPN-Filter under group-policy . I Want to restrict the access from specified source  IP  (Public IP)

View 1 Replies View Related

Cisco Firewall :: Can Configure More Than One Syslog Host On ASA 5500

May 31, 2012

I would like to send my ASA 5500 logs to more than one syslog server - is this possible?  I can't seem to find it in the documentation.

View 3 Replies View Related

Cisco Switches :: SF300-24P / 48P And ASA 5500 - Configure VLans

Oct 2, 2012

I saw a post in [URL] that was close to what I need to do.  But this site seems a better place to ask a question. We need to install a second switch (SF300-24P) to an existing network with an SF300 48P and an ASA5500 for gateway/firewall etc. the network on the 48p switch is 192.168.1.xx.  We want to use the new switch for ip cameras and 192.168.2.xx.
 
I will assume I need to set up a vlan on the 24 port switch for the 192.168.2.xx ip range, i will call this vlan20.  I will guess that I need to pick a port from the 48p switch and create  vlan20 on the 48p switch to access the 24p switch.  I want users on the 192.168.1.xx network to be able to access cameras on the 192.168.2.xx network.  Do I need to add a line in the asa config file for the new switch?

View 4 Replies View Related

Cisco Firewall :: Redirect Ip Address For Protocol With ASA 5500

Jan 5, 2012

On the inside interface and network, we have a server at, (as an example) 192.168.87.1, which acts as an email server.
 
The outside ip address of the ASA is, say, 200.0.0.1.
 
The ASA directs any imap requests from the outside interface to 192.168.87.1, which works fine from the outside. Users simply open up email, and collect emails etc.
  
When they come inside the office, their machine of course attempts to contact the ip address 200.0.0.1. the ASA knows it is outside interface, so they are unable to collect emails.
 
that any internal IMAP requests from machines on the inside to 200.0.0.1 are directed to the machine inside on 192.168.87.1?

View 5 Replies View Related

Cisco VPN :: ASA 5500 - IPSEC Tunnel Via Hostname Instead Of IP Address

Mar 1, 2012

Is it possible on an ASA 5500 device to connect an IPSEC tunnel via hostname instead of the IP address?  I have a site without a static IP address that is currently connected via Easy VPN but I want to change one of the sites to a regular IPSEC site to site as one side, the one with the dynamic IP, is being changed to SonicWALL.  I will have DDNS setup on the site with the SonicWALL so I want to know if I can point the ASA device to the hostname instead of the IP.

View 4 Replies View Related

Cisco WAN :: 5500 - Way To See Expired Guest Users / Assigned IP Address?

Mar 21, 2013

We recently implement WLC 5500 Series, I found out guest user once period of that user expired it will not appear at lobbyadmin page where you can see list of users.

Is there any way to see expired guest users and also IP address which assign to guest user?

View 2 Replies View Related

Protocols / Routing :: SR 5500 - Finding IP Address Of A Device?

Nov 15, 2011

Okay so currently in my possession is a SR 5500 wireless channel receiver with a problem.. We need to find its current ip address it also is not a standard ip address such as 192.168.xxx.xxx it has a standard ethernet port and of course GPIB ports

I'm looking to know if there is a way I can find its ip address by maybe with a crossover cable, or by bridging its connection to my computer and somehow seeing what ip it's requesting.

View 1 Replies View Related

Cisco VPN :: PIX 515E VPN Client Static IPs?

May 13, 2013

I have my PIX 515E (8.0(4)24) configured for VPN access. In the VPN configuration, I am using an RA tunnel group configured to use Windows 2003 IAS to authenticate users against active directory based on group membership and using a local IP pool for address assignment. This all works fine. I got a request from a single user to have a static IP assigned from the pool. I read that one way you can do this is to get into the user properties in Active Directory for the user and in the dial-in tab tick the box for 'Assign a static IP address' to have it give the particular user a static address for VPN, but it does not work. What I would like the PIX to do is assign addresses from the local pool unless there is an address assignment configuration in RADIUS. Basically does the PIX honor the IP assigned via RADIUS even if the tunnel group is configured for a local IP pool or do I need to configure the tunnel group to use AAA address assingment for the AD dial-in config to work at all? Does the PIX functions this way? I configured the user in AD for this but it does not work. I also have the no vpn-addr-assign aaa command enabled in there which might be the whole issue. I will try to change this in the next window and see if it flies then. Just wanted to see if the PIX works this way or if I am way off here.

View 5 Replies View Related

Cisco Security :: ASA 5510 Client Static IP

Sep 28, 2011

I have a ASA 5510 that uses Radius for Authentication.  What I am trying to do is assign each user that logs into VPN to have a specfic static IP based on userid.  I have about 30 to 50 users.  I don't want to complicate this by having them select a different profile when logging into the ASA.  What is a clean and simply way to assign user static ip and not use local database for login?

View 1 Replies View Related

Cisco VPN :: Remote VPN On ASA5510 Getting Static IP From ASA5520

May 22, 2013

i configured a remote VPN on cisco ASA 5520 and everythings seems to be working fine...DHCP IP were been lease to users that connect to the VPN. but the issue now is that our customer want a static IP to be given to a particular user when he connect via VPN.

View 1 Replies View Related

Cisco VPN :: ASA 5510 - VPN Between Remote Site And Static IP

Nov 11, 2011

I have a Cisco ASA 5510 with static IP and a Remote site with dynamic IP and i want to setup VPN between these 2 sites. i tried it many times but it doesn't come up.
 
I want to know how to do it?

View 3 Replies View Related

Cisco VPN :: 2911 - Static Ip Remote Clients

Aug 9, 2011

I am using Cisco 2911 router , i configured remote client in that . i need to provide the static ip to the remote users instead of providing from the dhcp pool. is it possible? if it is how we can do that.

View 5 Replies View Related

Cisco Routers :: Setting Up Static IP For Client Rv220W

Dec 16, 2011

Initial setup with RV220W completed without difficulty,Need to set up static IP for one of the machines in the LAN (not static IP for WAN),I presume I use the static DHCP option, which allows me to select a particular IP for the machine I select based on it's MAC,1. My confusion stems from the manual stating that "the IP address that you pick should be outside the DHCP address range specified on the Networking> LAN(local network)>IPV4(local network)page".,Does that mean that the range on the IPV4 local network page should be modified to exclude the IP address that I want to use for the static IP..e.g. change the range from 1-255 to 1-200 and then use an IP of XXX.XXX.X.201 for instanceor does that mean that as soon as I choose an IP on the Static DHCP page, that if will reserved for use only on that machine and not used for another machine on the LAN, without me having to do something else to exclude it's use (i.e. does reserving a static IP automatically remove it from the range of IPs available to other machines)If I simply set a static IP on the local machine by going to "change network adapter" settings, what's the liklihood that the router might use the same IP on another machine.

View 2 Replies View Related

Saving Client Static Network Settings?

Jan 23, 2011

I have a laptop that travels alot to different networks. I go to two differnent networks where I need to enter static network settings (wireless nic). How the heck do you save these settings so I don't have to enter them all the time. I know you can save the network profiles but does this save static settings assigned to the wireless nic?

View 3 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved