I have a laptop that travels alot to different networks. I go to two differnent networks where I need to enter static network settings (wireless nic). How the heck do you save these settings so I don't have to enter them all the time. I know you can save the network profiles but does this save static settings assigned to the wireless nic?
View 3 RepliesOn a Microsoft xp network when we log off or shut down (randomly) users will have their computers lock or freeze at saving settings. The network is school district with around 1000 computers total.
-We think it is an issue with DNS or DHCP but we can not find anything only about our issue.
-It occurs randomly, but seems to target certain machines more. In a lab about 3 quarters of the computers are not affected and the other quarter will have it happen, but not every time. It will happen on student, teacher, and admin accounts.
-It has "spread" to 3 buildings now. At first it seemed to be an issues at one building but over the course of a week two new buildings are affected.
-No major changes in our network over the past month either.
I have 3com router and it is working fine. The issue is that when I am taking the router out of the electricity and reenter it back it will not save my settings and I will have to log in again to change the settings.
View 1 Replies View RelatedI just recieved a WAP4410N and managed to log in to the web interface. It is not allowing me to change many settings. I try to change the wireless network mode and click on save and it goes back to disabled again.
P.S. I have just upgraded the firmware to 2.0.3.3 and tried to set it back to the factory defaults. neither worked.
What do the broadcom power saving mode settings mean? If power saving mode is enabled, what is the time it takes to go into power saving mode? What does fast mean?
View 1 Replies View RelatedRegion : Canada
Model : TD-W8961ND
Hardware Version : V2
Firmware Version : 2.0.0 Build 120608 Rel.34612
ISP : TekSavvy
NAT is enabled (under PVC2), as is UpNP
Whenever I enter all the info for a port forward under NAT in the virtual server tab, I click 'save' and nothing happens; chrome and firefox both give the same result.If I go to a different screen after pressing save and then come back to NAT settings, there's no entry updates and no port forwards.Should I install a different firmware (I can't find a newer version to install) or is NAT not supposed to work under PVC2? If I don't enter proper info (like leave the ports blank) I get an error if I press 'save', asking me to finish entering all the required info.
When I change a setup setting and click save settings, most of the time it gets stuck on the "saving..." notification window and eventually I get a "Internet Explorer cannot display the web page" notification. However I have found that if I repeatedly try it eventually it will accept the change. This never happens using the wizards only making manual changes. I am running the camera with a Wi-Fi connection. I am not sure this is a router or camera firmware bug (running V1.12)
View 4 Replies View RelatedThere are several features that don't work and are returning errors. For starters, when trying to save settings for media/device prioritization I am receiving a 2123 error message. Unable to save settings. EA4500/N900 Router, Cisco Cloud Connect.
View 3 Replies View RelatedI have the dir-601 as my main router. Its IP settings are dynamic, not static. My second router, the router I'd like to use as the access point is a Belkin Wireless G Mimo. My goal is to setup the Belkin as an access point downstairs away from the main router. I'd like to do this wirelessly. I'd like to phsycialy plug devices into the Belkin, while the Belkin receives access to the internet wirelessly from my main router, the dir-601.
Here's my issue. There's an easy option to use the Belkin as an access point. So I do this and set the Belkin router to an IP outside the DCHP range ( currently 192.168.0.100 - 192.168.0.199 ) to 192.168.0.250. My dir-601 will only recognize the Belkin access point while plugged in physically. I know this because when I did a ping test it only see's the Belkin when plugged into the dir-601 via ethernet cables. My ultimate goal is to simply set the dlink dir-601 to recognize the Belkin as an access point.
I am trying to put a link on our Intranet page to several documents that are updated daily by specific users. These users save the documents in their department folders, which are only acessible by their department and I.T. (me). Right now I have a .bat file that checks every half hour of the work day to see if it has been updated, if it has it will be moved to a location in the Intranet folder which will update the link on the Intranet. While users can view the Intranet, they do not have access to view the files or folders that house the Intranet html coding etc.This option works but our users are complaining that it isn't instantaneous. Any ideas how I can do this on a network while keeping everyone's security in place and not give them extra rights to the Intranet folders?
View 3 Replies View RelatedHow do I change my cisco wireless from a dynamic setting to a static settings.
View 1 Replies View RelatedIs there an alternate way to get the DNS settings off of the router? I've followed all of the steps up above, but I cannot set up a static IP Address on my computer without knowing the routers DNS settings, which I cannot retrieve from the web-based setup due to the corrupt firmware.
View 2 Replies View RelatedI recently upgraded to the EA4500 and the only issue I'm having is that it will not recognize my static DNS settings, which worked fine on my older E2000. No other hardware has changed except the router.I've tried both Google DNS and OpenDNS. In either case, the DNS settings can be entered and saved in the Basic Settings tab, but when I go to the admin tab, it shows my ISP's deafult DNS.
View 4 Replies View RelatedI had an WRVS4400 (but didn't use the wireless), it it died. I'm replacing with an RVS4000. I have all the settings from the prior router, but my question has to do with the DSL modem in use in conjunction with the router, because (in my absence) my wife had a conversation with SBC, trying to use the hook to the modem directly and ended up altering settings on the modem that may affect the RVS4000 when I go to install it upon its receipt from Amazon tomorrow.
We have a business that uses a third party software vendor's website; their servers access our data on our server behind the router. So we use a static IP address, and port forwarding. No problem there. But I could have sworn that, with the WRVS4400 we used to have the modem configured as bridged; as of this morning, the modem shows PPPoE, and my wife can't recall what SBC had her do in that regard!
So, for the situation I've described, should I put the modem into bridge mode (and porting it into the RVS4000). Like I said, we have a static WAN IP address, and a range of more static IP addresses.
I am trying to setup my Internet connection on my linksys E1200 router using static IP settings below -I am getting following error when trying to do this. These are the IP settings provided to me and are configured on my laptop to connect to my ISP as well.
View 6 Replies View RelatedI have my PIX 515E (8.0(4)24) configured for VPN access. In the VPN configuration, I am using an RA tunnel group configured to use Windows 2003 IAS to authenticate users against active directory based on group membership and using a local IP pool for address assignment. This all works fine. I got a request from a single user to have a static IP assigned from the pool. I read that one way you can do this is to get into the user properties in Active Directory for the user and in the dial-in tab tick the box for 'Assign a static IP address' to have it give the particular user a static address for VPN, but it does not work. What I would like the PIX to do is assign addresses from the local pool unless there is an address assignment configuration in RADIUS. Basically does the PIX honor the IP assigned via RADIUS even if the tunnel group is configured for a local IP pool or do I need to configure the tunnel group to use AAA address assingment for the AD dial-in config to work at all? Does the PIX functions this way? I configured the user in AD for this but it does not work. I also have the no vpn-addr-assign aaa command enabled in there which might be the whole issue. I will try to change this in the next window and see if it flies then. Just wanted to see if the PIX works this way or if I am way off here.
View 5 Replies View RelatedI have a ASA 5510 that uses Radius for Authentication. What I am trying to do is assign each user that logs into VPN to have a specfic static IP based on userid. I have about 30 to 50 users. I don't want to complicate this by having them select a different profile when logging into the ASA. What is a clean and simply way to assign user static ip and not use local database for login?
View 1 Replies View RelatedInitial setup with RV220W completed without difficulty,Need to set up static IP for one of the machines in the LAN (not static IP for WAN),I presume I use the static DHCP option, which allows me to select a particular IP for the machine I select based on it's MAC,1. My confusion stems from the manual stating that "the IP address that you pick should be outside the DHCP address range specified on the Networking> LAN(local network)>IPV4(local network)page".,Does that mean that the range on the IPV4 local network page should be modified to exclude the IP address that I want to use for the static IP..e.g. change the range from 1-255 to 1-200 and then use an IP of XXX.XXX.X.201 for instanceor does that mean that as soon as I choose an IP on the Static DHCP page, that if will reserved for use only on that machine and not used for another machine on the LAN, without me having to do something else to exclude it's use (i.e. does reserving a static IP automatically remove it from the range of IPs available to other machines)If I simply set a static IP on the local machine by going to "change network adapter" settings, what's the liklihood that the router might use the same IP on another machine.
View 2 Replies View RelatedCan the client lease time be set to never expire to prevent loss of connection for wireless printer with a permanent ip address on E3200? Or is there another way to ensure continuous connection?
View 6 Replies View RelatedI have a Cisco 876 router running 12.4.(15)T5, configured as DHCP client. This works nicely.
A Cisco 886 router, running 15.1 software also works with the DHCP client. This also works but has the following strange beheaviour: In the running-config an ip route 0.0.0.0 0.0.0.0 <dhcp assigned address> appears. Also - some other static routes that are in the config using the dhcp keyword are duplicated with the dhcp-assigned address
Now - when a write mem is done, these dhcp-generated route entry's are stored in the startup-config...
This beheaviour is completely different and VERY unwanted. After a change from DHCP server the config will simply stop working, when a write mem was done at the first DHCP situation.
Should we stop using write mem commands when a DHCP client is active in IOS? Is it a bug? Is it a feature?
i am trying to configure static ip on remote client user side , i am using the following doc as an example but i am not getting the ip which i am mentiong in the user .[url]...
View 10 Replies View RelatedI have a couple a questions answers on which i cant google for a period. BTW maybe i simly use wrong aproach to choose keywords.
1) Is it possible to assign same ip address to the same client each time it authenticated, preferably without using DHCP? Im definely sure that it possible but cant find corresponded configuration examples (my device is Cisco 1921 with IOS 15.0.1).
2) Is it possible to assign dynamic crypto map to loopback interface (the purpose to make EASY VPN Server accessible through two interfaces - maybe you recommend other approach instead?) - as i move workingcrypto map from phy int to loopback - i cant connect with reason "Phace1 SA policy proposal not accepted"
i am not sure if this is something with my DHCP setup or not, but it certainly seems to be the culprit. I am running a 3560G and using it as DHCP and to do V LAN routing (Geiger protocol). I have 10 pools configured with a few static addresses per pool. Now to get down to the problem. I have a computer (and this problem seems to be a gremlin as it changes what computer is affected quite often) that will connect, get its IP, immediately disconnect, then send out a DHCP req again. The computer has a static assignment in the pool, and for the brief second that it connects, it gets the right address. If i move the computer to another v lan, all works right. If i delete the static entry it will get an address in the right v lan no problem. The command i have been using to add static entries is:
address xxx.xxx.xxx.xxx client-id 01xx.xxxx.xxxx.xx
That seems to have been working on all my static routes except for a bank of computers in vlan3. I have went as far as to delete the pool and recreate it, heck i even recreated the v lan and i am still having issues. Below are some snippets of the running config for review.
The DHCP Pool for the affected LAN:
ip dhcp pool Dev3
network 192.168.3.0 255.255.255.0
boot file bootx86wdsnbp.com
next-server 192.168.1.78
dns- server 192.168.1.8 192.168.1.78
[Code] .....
I installed an IP camera, and had to change my E1000 router settings to a static IP address. Now I can't access the router settings. 192.168.1.1 is still the default gateway, but it won't open in any browser.
I'm reluctant to do a reset because it took me quite a while to figure out how to get the IP camera and port forwarding working (it does!), and I'd hate to do it all again and come to the same place. I'm not very good at this stuff, and it's a small miracle that I did it once.
I use my desktop for streaming media throughout the house. I found it was causing lag for gaming most likely because it was taking up all the bandwidth for the router. We had a 2nd router laying around as well as a 2nd wireless adapter so we set up a 2nd network that was not connected to the internet for strictly media streaming.I attempted to change the network settings so the internet connection appeared as a public network so that streaming of media was hopefully diverted to the non internet wireless adapter.I want a faster way of transferring large video files from my laptop to my desktop. I recently bought a crossover cable to do this through direct connection.Both use the same user name and password as well as run the same win 7 pro however the desktop is the 64 bit version. I set up both ipv4 with the same addresses.When it has worked I am only getting a connection speed of just over 10mb and once I connect the crossover cable between the computers it knocks out my internet connection on the wireless card.
View 5 Replies View RelatedWe have a NETGEAR ProSafe™ 802.11g Wireless VPN Firewall FVG318 set up at work with a static IP so we can do a Voice Over IP from our sales office.Everything works fine until I plug in a computer that is connected to our digital printer, then the PC stays on the internet for a while, then crashes the connection.Once I plug in the PC to the network, the rest of the network has issues.
View 4 Replies View RelatedI have a new DIR-655 and have successfully added three access policies. I am trying to add a fourth, and have gone through the wizard making all the necessary entries. After saving, I get back to the list of existing policies, but the one I just added does not appear.
View 2 Replies View RelatedI'm having 1841 Router, its configuration is not getting safed. If I reboot the router all my running-config is like default. But when I check my sh startup all the configuration which I did is displayed. Checked the config-registery too and its 0x2142 changed too 0x2102 still the same problem, when reloading the router all the running config is disappeared.
View 2 Replies View RelatedI'm not sure if this is even possible, but I'm currently changing from saving my documents on my desktop to a server. However, I like working with files from my desktop for ease of use. Is there any way to save a document in the server, while working with the document as it exists on my desktop (e.g. set the file up to save in two locations)?
View 1 Replies View RelatedI have a wireless deployment using a 5508 controller and 90+ LAP1142N lightweight access points.Everything is going relatively well, except I have about 3 that do not keep their config (hostname and AP group) past a reboot of the access point.When they do come up after a reboot, they go back to the default hostname of the mac address and are placed in the default-group AP group.
View 5 Replies View RelatedI have a DIR-655 that was working for the longest time, then out of the blue it just decided to stop getting a connection to the internet. I can connect to the router, but for some reason, it will not get any network settings. When I check the status/device info/WAN section, it just shows:
[code]....
Whenever I access a file through HTTP, it seems to require that I completely load the file before it will display.
1) For large images, this will result in the whole thing taking some time to load before displaying in its entirety, unlike the usual progressive rendering.
2) For file downloads, this will result in the file being downloaded only after being cached, appearing only when the whole file has finished downloading, unlike the usual process where it can be seen as a progress bar in the browser's download window (for some reason, FTP downloading seems to work normally)
3) For internet streaming video, this means the video will not display until the whole video has been buffered (i.e. will not play until fully loaded)
1) I am on a home network. Other computers (including my old one) do not exhibit similar problems
2) Using Firefox 9.01
3) Win 7 SP1
4) Realtek PCIe GBE controller
I'm accessing a NAS server remotely through VPN (Netgear FVG318). I can connect to the NAS server but it is very slow when opening and saving documents. When accessing the network drive I am connected to the Internet through wireless connection. When I connect to the Internet through Ethernet cable opening and saving documents is much quicker. Is there anyway I can make the remote access quicker when accessing it through a wireless connection?
View 1 Replies View Related