I'm having 1841 Router, its configuration is not getting safed. If I reboot the router all my running-config is like default. But when I check my sh startup all the configuration which I did is displayed. Checked the config-registery too and its 0x2142 changed too 0x2102 still the same problem, when reloading the router all the running config is disappeared.
View 2 RepliesI have a couple of SF300-24 switches. When I made needed configurations using CLI or GUI and then saved all configurations. The problem is that switches do not save configurations after reboot.
View 2 Replies View RelatedI have a Cisco 850 router that whas having problems getting an ip address via DHCP. I did some stuff on it but that didn't work, so I rebooted the router to go back to my last saved startup config. When I turned it back on and connected t othe CLI console I got the "Would you like to enter the initial configuration dialogue?" message. Thinikng I just forgot to save anything to the startup config I went through the initial set up again and made sure to save everything to the startup config. After going through the intial config and setting up a vlan to assign DHCP to clients I saved the config and rebooted, upon reboot and connecting to the CLI console I got the same "Would you like to enter the initial configuration dialogue?" message. Tryign the setup once more and making sure everything was saved to startup config I rebooted again just to make sure the changes would stick, and sure enough they didn't. Whay is the config not saving to the startup config?
View 3 Replies View RelatedI have a number of SFE2000 10/100 24 port POE switches. They are configured and running OK. I want to be able to save the configuration and be able to load that saved configuration into another new swich in the case of a failure.
I have logged in and gone to Admin-File Management-Save Configuration. I then select the 'Backup' radio button and TFTP the configuration to my TFTP server. All works OK and I have a readable text file with the switch configuration on my TFTP server.
I want to be able to restore that saved configuration on to a new switch. I have set the new switch back to factory defaults. I go to Admin-File Management-Save Configuration. I then select the 'Upgrade' radio button and try and uploade the file into the switch. If load to 'Running Configuration' the switch shows a status of 'Copy Finished' but says 'Copy completed with errors' If load to 'Startup Configuration' the switch shows a status of 'Copy Failed' and says 'Copy completed with errors'
I am guessing I should be able to load my saved Configuration back into a switch, shouldn't I??
And yes the switches are running the same firmware 3.0.0.17
I'm running LMS3.2 and RME 4.3.1. I deployed a netconfig job to our network which consisted of approximately 800 devices.The report said that the job completed successfully however some of the devices didn't save thier running config to startup.
Is it possible to add a command or issue another netconfig job just to save the running config, so I can identify if the job fails on some devices? Using the tick box in the netconfig job doesn't seem to alert you if its not successful.
Using the SGE 2010 for Microsoft NAP with 802.1x auth for switch access, which led to a few issues
What i have: An SGE 2010 48 port switch, firmware 3.0.0.17 Firmware upgrade: In order to ensure im not having problems due to old firmware, i tried to upgrade using ros_ls1_bp_ge_bx-3020.ros in order to move to 3.0.2, when uploading the file via TFTP, the upload completes and thats it, nothing happens.Restarting the device: As part of the upgrade process, i thought i might of had to reboot, so i rebooted, and found that all my settings were wiped clean, as if a factory reset had been performed.... and add further to pain, the backup of settings that i had taken do not seem to want to re-apply.NAP support: So i have tested my NPS (radius) server with NTRadping.exe and all is good, however i cannot get the SGE2010 to talk to it.... the authenticator state in the web interface is always listed as initialising.... im not sure if this is a simple incompatibility (hence the attempt at a firmware upgrade), a tag that needs to be set on the radius side or a switch misconfig.
1) how on earth do you upgrade the firmware?
2) why are none of my settings being saved when the device reboots ?
I have a 1711 Catalyst router hooked up behind a cable modem. I configured the router, copied running-config to start up-config then wrote it to memory with "write mem". I unplugged router to move it and when I plugged it back in, I had to start from scratch.
Is this normal, or should router be able to save configuration if powered down?
BTW, I'm using Putty to access router console. Is that the hot setup for Windows 7 or is there something better?
I currently am trying to program the config for a 1720 router however i cannot get the config to stick. I boot up to the command prompt put in all the configurations use the "write mem" command and then hard reset the router but when it boots back up I get the initial system configuation dialog.
I have tried booting to the rommon prompt and typing "confreg" and following the prompts keeping all options set to no except for this setting
"enable "ignore system config info"? y/n [n]: Y"
Is set to yes. but when i get to the end of the config it just loops and starts over with
"you wish to change the configuration? y/n [n]: Y"
If i choose yes it loops if I choose no it goes back to the rommon prompt.
When I try to save the configuration it displays the following error.Is it due to insufficient memory?
MPF-ASA#wr mem
ERROR: % Unrecognized commandMPF-ASA(config)# wr memBuilding configuration...Cryptochecksum: 81c514b8 9e95ee97 8b512148 b31377a4
[Code]...
I have a little problem configuring NAT on router 1841, like this is the topology:
WAN (PUBLIC´S ADDRESS) fast0/0 fast0/0/0 PUBLIC´S ADDRESS INSIDE (192.168.1.0/24)
ROUTER ====== X.X.X.X/30============= ROUTER ======== Z.Z.Z.Z/29 ============ SW 3560==============
(ISP) .253 .254 CLIENT . 47 .48
The connection with ISP or Extra net is a metro Ethernet, so the isp gave two ip address to the client: WAN (/30)
LAN (/29) Which be the public addresses to be used by the client if you need to publish any server on the network (like WWW), so they do not have any device that will could do the nat, like an asa or linux server, so the router has to do the Nat, because the SW 3560 does not support this feature.
So... I did the following:
On router 1841:
inter fast 0/0
description WAN
no shut
[ code ]...
I create an interface Blackpool to simulate the LAN connection (192.168.1.0/24)
Inter loopb 0
ip address 192.168.1.254 255.255.255.0
ip nat inside
[ code ] ...
ON SWITCH:
interface vlan 448
description LAN-ME
ip address Z.Z.Z.48 255.255.255.248
no shut
ip route 0.0.0.0 0.0.0.0 Z.Z.Z.47
But if i try to do ping from the ip address 192.168.1.0/24 to any server´s internet the ping fails, but if i do the ping from v LAN 228 the ping is success. I will think that route map could solve the problem.
I have 2 cisco 1841 routers the one is connected to my local network and the other is the stub router and it only has 2 fastethernet interfaces. fao/1 connected to the local network and fa0/0 connected to the internet and to the other router. How can i configure NAT on the fa0/0 which is sharing the internet and local network
View 1 Replies View RelatedI am configuring a 1841 router for use in small out office. I will use the s0/0/0 for main WAN T1 connection. I then wanted to use the ATM0/1/0 WIC-1-ADSL card as a failover. I am using weighted static routes for failover. Fe0/0 is LAN interface. When I go into SDM and look at the ATM interface it says this configuration is unsupported?
1. Can't I just get a DSL modem and connect it to fe0/1 and not use ATM WIC and use below for failover?
2. If I have to use ATM WIC what needs to be configured for it to work with Att aDSL?
my problem in configuring a cisco 1841 as VPN server using SDM, everytime i press Lunch Easy VPN Wizard botton, there were no response at all. my IOS is:
Cisco IOS Software, 1841 Software (C1841-ADVIPSERVICESK9-M), Version 12.4(15)T15, RELEASE SOFTWARE (fc3)
ROM: System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)
System image file is "flash:c1841-advipservicesk9-mz.124-15.T15.bin
by the way I took this IOS to other router with the same model(CISCO1841).
I'm trying to get a PPPoE config working on an 1841. Running c1841-advsecurityk9-mz.124-3i.bin . I tried c1841-advsecurityk9-mz.151-4.M4.bin but it has even less protocol options.
I used a walkthrough but it suggests the following fragment which doesn't work because there is no "protocol ppoe" command available on my system. Perhaps there is a simpler way to do this? I tried c1841-broadband-mz.151-4.M4.bin but it doesn't seem to have ssh available.
vpdn enable
vpdn-group 1
request-dialin
protocol pppoe
exit
[Code]...
I have the following very simple policy configured on a Cisco 1841.
policy-map Shape-2Mb class class-default shape average 2000000 interface FastEthernet0/1[code]....
I'd just like some clarification on the best ways to monitor this. Looking at the 'sh policy-map int fa0/1' i get this:
FastEthernet0/1 Service-policy output: Shape-2Mb Class-map: class-default (match-any) [code]...
some of the sections don't make much sense to me. What is the output of that command.
On new 1841 Testing Router, I deleted the flash & did the reload. After reloading, instantly I entered into the Rommon mode. I have a backup of the flash in my TFTP Server, which is connected to the 1841 Router. how can I restore my flash file into my 1841 Router. I can not get myself out of Rommon mode. I also now even can not ping the TFTP Server as well. Do I have to configure in the Rommon mode ?
how to restore the flash image via TFTP Server on my 1841 Router.
I have a Cisco 1841 router with an HWIC-ADSL module installed. My ADSL connection is PPPoA with a dialer interface and I have been provided 6 ip's from my provider to use on this service. Previously I have connected Fa0/0 on the 1841 straight onto my network and used NAT and ACL's on the 1841, I would now like to change this and have Fa0/0 connected to a Palo Alto firewall and use the Palo Alto to provide NAT, Firewall & site to site VPN functions. What config would I require on the 1841 to allow me to use one of my ISP IP addresses on the Palo Alto to allow it to be a VPN endpoint? Do I need to configure the 1841 in bridge mode?
View 3 Replies View RelatedI am trying to configure a Cisco 1841 to allow the users to access the internet. This is my first step with ppp. All the rest of the configuration is ok but I don't know how to setup the interfaces Dialer0 and ATM0/0/0.
Need very basic configuration that I can analyze and use on my device?
I have a Cisco 1841 Router with ADVANCE IPSERVICE IOS .The said router does not safe config, even after saving the config? As soon as the power cycled all the config will be lost? what can be done to correct this ?
View 1 Replies View Relatedi have a 1841 cisco router and i recently purchased a 1 port HWIC wan interface card. My problem is that I cannot see the interface in my config file. Is there something i am missing?
View 8 Replies View RelatedI have a wireless deployment using a 5508 controller and 90+ LAP1142N lightweight access points.Everything is going relatively well, except I have about 3 that do not keep their config (hostname and AP group) past a reboot of the access point.When they do come up after a reboot, they go back to the default hostname of the mac address and are placed in the default-group AP group.
View 5 Replies View RelatedI just recieved a WAP4410N and managed to log in to the web interface. It is not allowing me to change many settings. I try to change the wireless network mode and click on save and it goes back to disabled again.
P.S. I have just upgraded the firmware to 2.0.3.3 and tried to set it back to the factory defaults. neither worked.
On a Microsoft xp network when we log off or shut down (randomly) users will have their computers lock or freeze at saving settings. The network is school district with around 1000 computers total.
-We think it is an issue with DNS or DHCP but we can not find anything only about our issue.
-It occurs randomly, but seems to target certain machines more. In a lab about 3 quarters of the computers are not affected and the other quarter will have it happen, but not every time. It will happen on student, teacher, and admin accounts.
-It has "spread" to 3 buildings now. At first it seemed to be an issues at one building but over the course of a week two new buildings are affected.
-No major changes in our network over the past month either.
I have 3com router and it is working fine. The issue is that when I am taking the router out of the electricity and reenter it back it will not save my settings and I will have to log in again to change the settings.
View 1 Replies View RelatedI have a new DIR-655 and have successfully added three access policies. I am trying to add a fourth, and have gone through the wizard making all the necessary entries. After saving, I get back to the list of existing policies, but the one I just added does not appear.
View 2 Replies View RelatedI was configuring a new Catalyst 2960 switch and had forgotten to set the speed back to 9600 after downloading the new IOS software image. I finished doing all of my configurations and went in to line con 0 to change the speed back to 9600. The change was accepted and I did a 'wr' to save the change, but when I reload the switch it is back to 115200.
View 3 Replies View RelatedI am trying to put a link on our Intranet page to several documents that are updated daily by specific users. These users save the documents in their department folders, which are only acessible by their department and I.T. (me). Right now I have a .bat file that checks every half hour of the work day to see if it has been updated, if it has it will be moved to a location in the Intranet folder which will update the link on the Intranet. While users can view the Intranet, they do not have access to view the files or folders that house the Intranet html coding etc.This option works but our users are complaining that it isn't instantaneous. Any ideas how I can do this on a network while keeping everyone's security in place and not give them extra rights to the Intranet folders?
View 3 Replies View RelatedI'm not sure if this is even possible, but I'm currently changing from saving my documents on my desktop to a server. However, I like working with files from my desktop for ease of use. Is there any way to save a document in the server, while working with the document as it exists on my desktop (e.g. set the file up to save in two locations)?
View 1 Replies View RelatedI have a laptop that travels alot to different networks. I go to two differnent networks where I need to enter static network settings (wireless nic). How the heck do you save these settings so I don't have to enter them all the time. I know you can save the network profiles but does this save static settings assigned to the wireless nic?
View 3 Replies View RelatedI am having difficulties saving, loading conifg files from a USB, what is the correct command for loading a config file from USB for cisco 3750x switch.
View 1 Replies View RelatedWhat do the broadcom power saving mode settings mean? If power saving mode is enabled, what is the time it takes to go into power saving mode? What does fast mean?
View 1 Replies View RelatedWhenever I access a file through HTTP, it seems to require that I completely load the file before it will display.
1) For large images, this will result in the whole thing taking some time to load before displaying in its entirety, unlike the usual progressive rendering.
2) For file downloads, this will result in the file being downloaded only after being cached, appearing only when the whole file has finished downloading, unlike the usual process where it can be seen as a progress bar in the browser's download window (for some reason, FTP downloading seems to work normally)
3) For internet streaming video, this means the video will not display until the whole video has been buffered (i.e. will not play until fully loaded)
1) I am on a home network. Other computers (including my old one) do not exhibit similar problems
2) Using Firefox 9.01
3) Win 7 SP1
4) Realtek PCIe GBE controller
I'm accessing a NAS server remotely through VPN (Netgear FVG318). I can connect to the NAS server but it is very slow when opening and saving documents. When accessing the network drive I am connected to the Internet through wireless connection. When I connect to the Internet through Ethernet cable opening and saving documents is much quicker. Is there anyway I can make the remote access quicker when accessing it through a wireless connection?
View 1 Replies View Related