Cisco :: LMS 3.2 / RME 4.3.1 - Netconfig Job Not Saving Running Configuration To Startup?
Feb 3, 2013
I'm running LMS3.2 and RME 4.3.1. I deployed a netconfig job to our network which consisted of approximately 800 devices.The report said that the job completed successfully however some of the devices didn't save thier running config to startup.
Is it possible to add a command or issue another netconfig job just to save the running config, so I can identify if the job fails on some devices? Using the tick box in the netconfig job doesn't seem to alert you if its not successful.
View 2 Replies
ADVERTISEMENT
Jan 18, 2012
I have a Cisco 850 router that whas having problems getting an ip address via DHCP. I did some stuff on it but that didn't work, so I rebooted the router to go back to my last saved startup config. When I turned it back on and connected t othe CLI console I got the "Would you like to enter the initial configuration dialogue?" message. Thinikng I just forgot to save anything to the startup config I went through the initial set up again and made sure to save everything to the startup config. After going through the intial config and setting up a vlan to assign DHCP to clients I saved the config and rebooted, upon reboot and connecting to the CLI console I got the same "Would you like to enter the initial configuration dialogue?" message. Tryign the setup once more and making sure everything was saved to startup config I rebooted again just to make sure the changes would stick, and sure enough they didn't. Whay is the config not saving to the startup config?
View 3 Replies
View Related
Mar 21, 2012
We were having a discussion in my group about startup vs running configs, and how often some network managers forget to "click save" when they configure a switch. Is there a way to configure Ciscoworks to copy the running config to the startup?
View 2 Replies
View Related
Oct 8, 2012
I'm having 1841 Router, its configuration is not getting safed. If I reboot the router all my running-config is like default. But when I check my sh startup all the configuration which I did is displayed. Checked the config-registery too and its 0x2142 changed too 0x2102 still the same problem, when reloading the router all the running config is disappeared.
View 2 Replies
View Related
May 3, 2011
I have a couple of SF300-24 switches. When I made needed configurations using CLI or GUI and then saved all configurations. The problem is that switches do not save configurations after reboot.
View 2 Replies
View Related
Apr 10, 2011
I have a number of SFE2000 10/100 24 port POE switches. They are configured and running OK. I want to be able to save the configuration and be able to load that saved configuration into another new swich in the case of a failure.
I have logged in and gone to Admin-File Management-Save Configuration. I then select the 'Backup' radio button and TFTP the configuration to my TFTP server. All works OK and I have a readable text file with the switch configuration on my TFTP server.
I want to be able to restore that saved configuration on to a new switch. I have set the new switch back to factory defaults. I go to Admin-File Management-Save Configuration. I then select the 'Upgrade' radio button and try and uploade the file into the switch. If load to 'Running Configuration' the switch shows a status of 'Copy Finished' but says 'Copy completed with errors' If load to 'Startup Configuration' the switch shows a status of 'Copy Failed' and says 'Copy completed with errors'
I am guessing I should be able to load my saved Configuration back into a switch, shouldn't I??
And yes the switches are running the same firmware 3.0.0.17
View 7 Replies
View Related
Jun 11, 2013
I have 30 switched in my corporate network it’s all up and running all switches running by default configuration and connected to WS-C4506 core switch our dhcp server pooling 192.168.100.1/27 network. Now we need to configure new Vlan for finance department this department has more than 200 users. If my server distributes 192.168.200.0 range ip can vlan2 automatically assign ip 200.0 addresses to finance department.All switches running default config no ip address assigned.
View 9 Replies
View Related
May 7, 2013
I need to replace an existing ASA 5540 with a new ASA 5525X. I would like to pre-stage and configure the new box with the existing config, migrate license and export certificate files before swapping it with the old one during a change window. The new firewall will run 9.1 on deployment. Now the same 7.2(4) cannot just be copied over to 5525X running the minimum 8.6 version. There is a Web based tool available at [URL] according to Cisco documentation but the page does not load for me (Cisco intranet only tool ?). Is there another tool for automatic conversion ?
View 3 Replies
View Related
Oct 7, 2012
Using the SGE 2010 for Microsoft NAP with 802.1x auth for switch access, which led to a few issues
What i have: An SGE 2010 48 port switch, firmware 3.0.0.17 Firmware upgrade: In order to ensure im not having problems due to old firmware, i tried to upgrade using ros_ls1_bp_ge_bx-3020.ros in order to move to 3.0.2, when uploading the file via TFTP, the upload completes and thats it, nothing happens.Restarting the device: As part of the upgrade process, i thought i might of had to reboot, so i rebooted, and found that all my settings were wiped clean, as if a factory reset had been performed.... and add further to pain, the backup of settings that i had taken do not seem to want to re-apply.NAP support: So i have tested my NPS (radius) server with NTRadping.exe and all is good, however i cannot get the SGE2010 to talk to it.... the authenticator state in the web interface is always listed as initialising.... im not sure if this is a simple incompatibility (hence the attempt at a firmware upgrade), a tag that needs to be set on the radius side or a switch misconfig.
1) how on earth do you upgrade the firmware?
2) why are none of my settings being saved when the device reboots ?
View 2 Replies
View Related
Nov 10, 2011
I have a 1711 Catalyst router hooked up behind a cable modem. I configured the router, copied running-config to start up-config then wrote it to memory with "write mem". I unplugged router to move it and when I plugged it back in, I had to start from scratch.
Is this normal, or should router be able to save configuration if powered down?
BTW, I'm using Putty to access router console. Is that the hot setup for Windows 7 or is there something better?
View 5 Replies
View Related
Aug 15, 2012
I currently am trying to program the config for a 1720 router however i cannot get the config to stick. I boot up to the command prompt put in all the configurations use the "write mem" command and then hard reset the router but when it boots back up I get the initial system configuation dialog.
I have tried booting to the rommon prompt and typing "confreg" and following the prompts keeping all options set to no except for this setting
"enable "ignore system config info"? y/n [n]: Y"
Is set to yes. but when i get to the end of the config it just loops and starts over with
"you wish to change the configuration? y/n [n]: Y"
If i choose yes it loops if I choose no it goes back to the rommon prompt.
View 5 Replies
View Related
Oct 3, 2011
When I try to save the configuration it displays the following error.Is it due to insufficient memory?
MPF-ASA#wr mem
ERROR: % Unrecognized commandMPF-ASA(config)# wr memBuilding configuration...Cryptochecksum: 81c514b8 9e95ee97 8b512148 b31377a4
[Code]...
View 1 Replies
View Related
Nov 19, 2012
don't have an option to connect a console cable to my cisco router. The usb to serial converter will not work in windows7 only on XP.have physical access to my 881 Cisco Router. If I remember correctly these routers have a default ip address. This router is brand new, out of the box. I am thinking I can access it with the correct IP via network instead of console.
View 7 Replies
View Related
Nov 15, 2009
I have a Cisco 2811 router and when I turn of the router the running config is lost. I have to the following to get the router running of the start-up config settings.
router#copy start-up running-config
View 9 Replies
View Related
May 27, 2012
Facing issue with 2960G switch , where its do not display "logging trap informational " in show running and show startup .where its showing all other levels from 0 to 5 and 7 after configuration and save commands. [code] after config getting saved , it do not shows in show runn or in show startup while for all other levels it do show the config lines .I tried the same on 12.55.SE release also but its same results . Is this a limitaion of this platform, is there any doc explaining the same for reference. [code]
View 1 Replies
View Related
Aug 14, 2012
I was working on a Cisco 2600 series router earlier today running IOS 12.4. I ran into an issue where I could not clear the startup-config. I tried:
router#erase startup-config
router#reload
router#erase nvram
router#reload
[code]....
each time IP addresses and things got cleared but other aspects did not which should have been. In the nvram there were several files:
Router#dir
Directory of nvram:/
126 -rw- 2143 <no date> startup-config
127 ---- 5 <no date> private-config
128 -rw- 2143 <no date> underlying-config
1 ---- 49 <no date> persistent-data
2 -rw- 0 <no date> ifIndex-table
View 1 Replies
View Related
Jan 9, 2012
There are two issues which are testing my resolve.
1) Bad Cryptochecksum Ignored error
2) Unable to boot to a save startup-config file.
I want to take the configuration from one ASA 5505 and move it to another ASA 5505. I copied the startup-config file from an ASA 5505 running asa821-k8.bin to an ASA running 8.222-k8 to flash using tftp. I set the boot config parameter on the new asa to flash:/startup-config which is the location of the startup file. If I use copy run start command, I over write the startup file. When I copy the startup configuration to the running configuration I get a Bad Cryptochecksum Ignored error and the startup file does not copy over to the running file. How can I resolve this issue?
View 1 Replies
View Related
May 21, 2012
I messed up the IOS on the flash of CISCO881-SEC-K9. On reboot it booted to ROMMON which allowed me to tftp up a working IOS c880data-universalk9-mz.151-4.M3.bin. Unfortunately somewhere in my playing around the default startup configuration factory loaded on the routerhas been erased. I can load a new a config on the device but as I'm using the router to learn its useful to have the original config load when I factory reset the device. What is the factory start up config?
View 3 Replies
View Related
Jun 17, 2012
I have pair of ASA 5550 and I am trying to copy a new config to my member1 (active) as the new configuration I want to use for the pair. I want to copy this to start-up config on member1 and then reload member1 and have it copy the same config to member2 (stdby). I guess I am trying to understand if I copy the configuration to member1 and reload it, member 2(stdby) will have become active and try to copy the old configuration to member1 which I do not want.
get the commands straight that I need to execute to make sure the new startup config gets to both members without being overwritten?
View 1 Replies
View Related
Jun 12, 2013
I have reconfigured the FEX numbers attached to a Nexus 5548 running on NXOS5.2 If I do show running-config the interfaces are not there anymore. But if I do show startup-config the old Fex interfaces still shows up. I did try write erase then saved the running-config and its still there.
View 1 Replies
View Related
Feb 4, 2013
I was wondering if I can force catalyst 2960 to skip startup config stored in NVRAM and boot with no config everytime it is powered. I tried to find it on google and in cisco white papers but still no luck. I found only commands that begin with "set boot config-register ... ", but switch acts like it does not know these commands.
View 7 Replies
View Related
Jan 4, 2012
I have an 877W router that I would like to have a 2nd pre-configured backup for. I was thinking of getting another 870 series (probably an 877) router, as the more expensive wireless option is not actually required. Am I right to assume that I could simply copy the contents of my current config.txt file onto the second router?
View 4 Replies
View Related
Jan 19, 2012
After upgrading to LMS3.2.1 I cant select devices in Netconfig. There seams to be a defect in the selection box:you have Task selection twice (left task-selector headlined with Device Selector) instead of device-selector left and task-select right.What can we do to can use netConfig?
View 1 Replies
View Related
Nov 2, 2011
I can't choose any devices when I try to launch a NetConfig Job in LMS 3.2.
I have to check in the job summary if the device on which I'll apply the job is the good one.
Unfortunately, this problem doesn't appear every time so I don't know where to look for an answer.
View 2 Replies
View Related
Oct 25, 2011
Would it be possible to change output style of "sh running-config" in SF-300 switches to Cisco IOS-like format (eg.: options related to the specific interface put together, add tabs) in the next release?
View 24 Replies
View Related
Jun 22, 2011
There are some troubles in my 7206 vxr . The process of this problem below.
LOG:
Self decompressing the image : ####################################################################################################################################################################################################################################################################################################################################################################
[Code]...
View 2 Replies
View Related
Jul 13, 2011
command to get running config of Cisco VPN 3000 concentrator.
View 3 Replies
View Related
Apr 28, 2013
I've recently received this new Cisco 1921 routers with Cisco CP loaded, so it comes up with the annoying change username and password at first access. I've removed all of those files from the flash memory, and rebooted it, and it came up with the proper initial configuration dialog, which is what I wanted. But, whenever I configure the router with a set of basic configuration, like interface, routing, and snmp loggings, and hit wr mem, it doesn't display at all when I do "sh run". It's weird cause when I do sh run | sec rip or any other stuff that I have configured, it shows up , but not in sh run at all.
What's the deal with the new routers? Even sh version doesn't show the config-register or memory allocation details.
xxxxx#sh ver
Cisco IOS Software, C1900 Software (C1900-UNIVERSALK9-M), Version 15.1(4)M4, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
[Code].....
View 5 Replies
View Related
May 24, 2012
I am using ACS5.2 I want user to access the device with all necessary command like show run/ver/int/log… I try to set user privilege using Shell from 1 to 10 but show run doesn't work.
View 15 Replies
View Related
Jan 9, 2012
I am wondering if it's possible to convert a Pix 501 configuration running version 6.3(5) to a new ASA5505 which we just purchased? We have site to site VPN on this device and i am just trying to save some time. I believe Cisco TAC might have a tool to do this but i am not sure.
View 4 Replies
View Related
Aug 7, 2008
We have a bunch of switches that are running fine but the running-config file is missing and we can't save the config to the tftp server. IOS is c3550-ipbasek9-mz.122-37.SE1. I've got lots of these switches running the same code that are just fine.
View 8 Replies
View Related
Jul 28, 2012
My issue is that when trying to run the setup software for my new cisco 4500 router, an error message comes up which states that the new mac operating system 10.8 aka mountain lion is not supported. so now i had no choice but to leave my network unprotected as i cannot run setup. I was just wondering if there was another method by which i can configure the router without running the setup cd.
View 3 Replies
View Related
Apr 2, 2012
My company is beginning to have a lot of sites were we are stacking 3 to 4 C2960S-48 switche.This is making "show running-config" very very long because of the 4 x 48 interfaces.I can’t find a CLI command that show me the running-config of a ranges of interfaces. If I for example would like to see running-config for switch 3 (interfaces 3/0/1-52)The Show Running-config will show all the interfaces (for the two first swtiche = 104 interfaces), which take a time before I reach to switch 3.I miss a CLI command like: show Running-config switch 3, or module 3, or show running-config interface range x/x/x-x ?I’m well aware of the CLI command show running-config interface x/x/x, but this will only show me one interface.
View 3 Replies
View Related
