don't have an option to connect a console cable to my cisco router. The usb to serial converter will not work in windows7 only on XP.have physical access to my 881 Cisco Router. If I remember correctly these routers have a default ip address. This router is brand new, out of the box. I am thinking I can access it with the correct IP via network instead of console.
View 7 RepliesThere are two issues which are testing my resolve.
1) Bad Cryptochecksum Ignored error
2) Unable to boot to a save startup-config file.
I want to take the configuration from one ASA 5505 and move it to another ASA 5505. I copied the startup-config file from an ASA 5505 running asa821-k8.bin to an ASA running 8.222-k8 to flash using tftp. I set the boot config parameter on the new asa to flash:/startup-config which is the location of the startup file. If I use copy run start command, I over write the startup file. When I copy the startup configuration to the running configuration I get a Bad Cryptochecksum Ignored error and the startup file does not copy over to the running file. How can I resolve this issue?
I am running the Startup Wizard from my browser as I do not have a Console Access for a brand new CISCO ASA and I am stucked with the User? Password ? I tried many combination and nothing worked.
View 1 Replies View RelatedI have a Cisco 850 router that whas having problems getting an ip address via DHCP. I did some stuff on it but that didn't work, so I rebooted the router to go back to my last saved startup config. When I turned it back on and connected t othe CLI console I got the "Would you like to enter the initial configuration dialogue?" message. Thinikng I just forgot to save anything to the startup config I went through the initial set up again and made sure to save everything to the startup config. After going through the intial config and setting up a vlan to assign DHCP to clients I saved the config and rebooted, upon reboot and connecting to the CLI console I got the same "Would you like to enter the initial configuration dialogue?" message. Tryign the setup once more and making sure everything was saved to startup config I rebooted again just to make sure the changes would stick, and sure enough they didn't. Whay is the config not saving to the startup config?
View 3 Replies View RelatedI'm running LMS3.2 and RME 4.3.1. I deployed a netconfig job to our network which consisted of approximately 800 devices.The report said that the job completed successfully however some of the devices didn't save thier running config to startup.
Is it possible to add a command or issue another netconfig job just to save the running config, so I can identify if the job fails on some devices? Using the tick box in the netconfig job doesn't seem to alert you if its not successful.
We were having a discussion in my group about startup vs running configs, and how often some network managers forget to "click save" when they configure a switch. Is there a way to configure Ciscoworks to copy the running config to the startup?
View 2 Replies View RelatedI was working on a Cisco 2600 series router earlier today running IOS 12.4. I ran into an issue where I could not clear the startup-config. I tried:
router#erase startup-config
router#reload
router#erase nvram
router#reload
[code]....
each time IP addresses and things got cleared but other aspects did not which should have been. In the nvram there were several files:
Router#dir
Directory of nvram:/
126 -rw- 2143 <no date> startup-config
127 ---- 5 <no date> private-config
128 -rw- 2143 <no date> underlying-config
1 ---- 49 <no date> persistent-data
2 -rw- 0 <no date> ifIndex-table
I messed up the IOS on the flash of CISCO881-SEC-K9. On reboot it booted to ROMMON which allowed me to tftp up a working IOS c880data-universalk9-mz.151-4.M3.bin. Unfortunately somewhere in my playing around the default startup configuration factory loaded on the routerhas been erased. I can load a new a config on the device but as I'm using the router to learn its useful to have the original config load when I factory reset the device. What is the factory start up config?
View 3 Replies View RelatedI have pair of ASA 5550 and I am trying to copy a new config to my member1 (active) as the new configuration I want to use for the pair. I want to copy this to start-up config on member1 and then reload member1 and have it copy the same config to member2 (stdby). I guess I am trying to understand if I copy the configuration to member1 and reload it, member 2(stdby) will have become active and try to copy the old configuration to member1 which I do not want.
get the commands straight that I need to execute to make sure the new startup config gets to both members without being overwritten?
I have reconfigured the FEX numbers attached to a Nexus 5548 running on NXOS5.2 If I do show running-config the interfaces are not there anymore. But if I do show startup-config the old Fex interfaces still shows up. I did try write erase then saved the running-config and its still there.
View 1 Replies View RelatedI was wondering if I can force catalyst 2960 to skip startup config stored in NVRAM and boot with no config everytime it is powered. I tried to find it on google and in cisco white papers but still no luck. I found only commands that begin with "set boot config-register ... ", but switch acts like it does not know these commands.
View 7 Replies View RelatedI have an 877W router that I would like to have a 2nd pre-configured backup for. I was thinking of getting another 870 series (probably an 877) router, as the more expensive wireless option is not actually required. Am I right to assume that I could simply copy the contents of my current config.txt file onto the second router?
View 4 Replies View RelatedI recenly installed LMS 4 on a windows 2008 R2 system , I didnt change the default configuration of windows or ciscoworks.I just added devices and configured basic things on the LMS system .when I open ciscoworks on the server itself it starts a browser session on http port 1741 and then changes automatically to https even though the default config is browser security disabled on ciscoworks.I try to open a browser session on a mgmt station to the cisco server , it didnt work in https ( I did get the login screen but couldnt log on , probablly something to do with the certificate ) , so I open http on port 1741 and it worked , I was able to log in .After a few Hours for some strange reason I didnt have access any more from the mgmt station not in http nor in https , the only way was to access it from the server itself.I went and changed the default setting of the secure browser on LMS 4 hopping that would work , I was asked to restart the ciscoworks service for the changes to take affect , I tried to restart it but it was unsuccesful so I restart the whole server. when it came up ciscoworks didnt work most services didnt start ( like the web server ,tomcat and all the manual services and ciscoworks deamon)
View 1 Replies View RelatedWe have a 861 router for our small office with 15 people. We have been experienced download problems for several months, but we have suspected the internet supplier to be the bottleneck as we have a new 861 router with the default configuration from the "Cisco Configuration Professional Express".
The sympton is that the download speed over http starts fast, but drops after a few seconds from 10MB/s to 3KB/s and stays there. The internet supplier came here today and made some tests. So we downloaded some huge files over the direct cable, and it was staying at constant 10MB/s. When we connected over the router it started at 10MB/s and dropped down to 3KB/s.
Is there something that has been forgotten in the "Cisco Configuration Professional Express"?
What is the purpose of these default configuration lines? What do they mean? I can't find an explanation of them anywhere. I believe some are written to the config when FCoE is enabled..
I would like to know exactly what they are doing.
class-map type qos class-fcoe
class-map type queuing class-fcoe
match qos-group 1
[Code].....
We have 3 WAP4410N on our network. Our laptops pick them up but I cannot access the configuration Utility or ping the default IP address. If their IP addresses have been changed how do I find out what their current IP adds are? We currently use static IP addressing for our network.
View 2 Replies View Related3750 switch connects to Blade-switch_1 and Blade-switch_2 Spanning-tree mode is configured as rapid-pvst on 3750 switch, do I need to configure rapid-pvst on both blade-switches or keep the default pvst config.3750 is running VTP domain HQ and transparent mode Both Blade_switches are running VTP domain CLI and transparent mode To configure Etherchannel between 3750 and blade-switch_1 do I need to have all devices in same vtp domain?
View 16 Replies View RelatedI have 30 switched in my corporate network it’s all up and running all switches running by default configuration and connected to WS-C4506 core switch our dhcp server pooling 192.168.100.1/27 network. Now we need to configure new Vlan for finance department this department has more than 200 users. If my server distributes 192.168.200.0 range ip can vlan2 automatically assign ip 200.0 addresses to finance department.All switches running default config no ip address assigned.
View 9 Replies View Relatedi wanna ask a question regarding automatic startup on lms 4.1, i have installed my LMS 4.1 on esxi 4.x . but recently my server sometimes down because the electricity problem. and when my friend push the power button to start the server, the LMS is not automatically active. is it possible to make it automatically active soon after my server power up ?
View 3 Replies View RelatedThe IT department in my university has installed enternet 300 on all of our pc's - we have to use this to log into the inter/intranet on the campus. According to them, it is not possible to have the computer automatically log onto the system. I looked into the program, however, and found a place to put ip addresses, account and password. Note: the IT department in my school works hard but it not known for developing complete knowledge about the platforms they work on - there are many.
Is this correct is it possible to put the program in the startup folder and let the computer log on automatically? To be honest, even though most systems on campus us win 2000, I thought win 2000 had the ability to do this (log on to a network) natively, so I am a little puzzled as to why they have this on the computer.
My old wireless card I took out demands these files when I log onto administrator. I have a new usb wireless card and I want the old card to stop bothering me when I restart/start/logon my cpu.the filert61.sys on ralink wireless lan installions disk is neededthere is a browse button set to c:program filesmsimsi wireless lanardinstallerwinxpI no longer have an msi folder in program files. I don't see it show up under add/remove programs in control panel. Under device manager there are three network adapters: my current wireless usb
View 1 Replies View RelatedWhen I fire up my PC, I cannot connect to the internet. Everything is plugged in properly, and I can ping my router and get a reply. I can even get on the internet just fine wirelessly with my netbook. To get the internet to work on my desktop, I have unplug my cable, disable my adapter, plug it back in and enable it.
View 19 Replies View RelatedWhen trying to start CiscoWorks Daemon Manager i get the following message:"The CiscoWorks Daemon Manager service on local computer started and the stoped. Some services stop automatically if they are not in use by other services or programs."I have tring starting the service from DOS also and get,E:Program FilesCSCOpxsetupsupport>net start crmdmgtdThe CiscoWorks Daemon Manager service is starting.The CiscoWorks Daemon Manager service could not be started. The service did not report an error. More help is available by typing NET HELPMSG 3534.
View 11 Replies View RelatedIve just started up a new cisco 887va-w and the startup wizard doesnt start. Is there a way to make this manually start?
What i tend to do is run the wizard for the basic settings then run 10-15 lines from the client (depending on adsl or vdsl config) to configure the router. But for some reason this one doesnt fire it after loging on with cisco cisco to 10.10.10.1 and changed the username and password. I just get the bebased cisco cp 'basic'. Cant see anyware on it to launch the wizard either.
Ive tried reset button on the back and reset to factory from cisco cp?
Software running on the unit is c800-universalk9-mz.spa.151-4,m4.bin
I just got a PIX 506e from a friend that was not longer using it. I'm trying to get started with the configuration page. I've reset it to factory defaults, rebooted and connected up ethernet. I can ping the device at 192.168.1.1 and access it via console. I browse the site https://192.168.1.1/startup.html, get the invalid ssl certification, get a login prompt (user/pass) and as the document says I leave it blank. As soon as I hit ok it goes to the 404 error Page Not found.
View 4 Replies View RelatedMy hp pavilion g6 has always had the problem of not connecting to internet after i restart it. It shows excellent signal but cant connect to internet. This has been the case on two different routers/modems with two seperate service providers, however the problem gets fixed by turning off then back on the modem/router.
View 8 Replies View RelatedIve got a wireless router and until just recently my desktop was able to connect to my network automatically. I went into network settings and made sure the "connect automatically" was checked but it did nothing. I have to manually go in and connect every time even though it recognizes that there is a network to connect to.
View 1 Replies View RelatedMy PC boots fine (via SSD) but as soon as it passes the login screen and brings me to the desktop, the network connection icon has a circle going around it for about 30 seconds. Except the circle isnt moving, or rotating as if it's frozen and when i click on it to go into the network and sharing settings, it hangs. While this happens i can access anything else fine except internet based apps. Once it connects, everything is normal.
I use a Netgear Power line Adapter and have been for years, and have never had a problem with it. I am running Windows 7 Enterprise 64 bit.
i have an urgent situation that my catakyst C3550 wont booting up after i reset the startup-configuration using "erase startup-config" command. now everytime i connect to the catalyst it show me "switch: " not "switch>", i have try using "boot" command in the "switch: " session but it said"Loading ""...: permission denied"error Loading ""
View 2 Replies View RelatedI'm running Win7 and have recently had problems at startup. Initially I thought this was a Skype issue as removing it seemed to work, but alas the problem remains with it uninstalled. The PC boots ok and I can open programs quickly enough, but if they need internet access they hang for 5mins or so before the block clears and all is well. I have recently changed ISP provider to BT Broadband (UK) and have a new router which sets itself up and had been working fine.
View 9 Replies View RelatedRecently, nearly every time I start up my computer, I can't connect to the internet. I have internet, as says my modem, what I don't have is an internet adapter. I've checked the device manager, and network and sharing center, and it just doesn't exist. I restart a few times and by chance it finds the adapter and I can connect. I have no idea what's going on, as Googling has not worked much at all.[CODE]
View -1 Replies View RelatedMy computer has started connecting to the internet on startup, I do not want it to do this, the answer i have already seen on here for this does not work, so how can I stop this?
View 1 Replies View RelatedAfter startup, the computer takes about 15 seconds for it to identify the LAN.
View 1 Replies View Related