Cisco :: LMS 4 Didn't Change Default Configuration Of Windows
Aug 18, 2011
I recenly installed LMS 4 on a windows 2008 R2 system , I didnt change the default configuration of windows or ciscoworks.I just added devices and configured basic things on the LMS system .when I open ciscoworks on the server itself it starts a browser session on http port 1741 and then changes automatically to https even though the default config is browser security disabled on ciscoworks.I try to open a browser session on a mgmt station to the cisco server , it didnt work in https ( I did get the login screen but couldnt log on , probablly something to do with the certificate ) , so I open http on port 1741 and it worked , I was able to log in .After a few Hours for some strange reason I didnt have access any more from the mgmt station not in http nor in https , the only way was to access it from the server itself.I went and changed the default setting of the secure browser on LMS 4 hopping that would work , I was asked to restart the ciscoworks service for the changes to take affect , I tried to restart it but it was unsuccesful so I restart the whole server. when it came up ciscoworks didnt work most services didnt start ( like the web server ,tomcat and all the manual services and ciscoworks deamon)
I was in the process of creating a AAA setup on my NX-0S (MDS9148), logged out/attempted to login to test AAA login and now I can no longer login as admin either! I didn't change the local account. I have the Cisco Device Manager open still (in the fabric switch) and how I remedy this (AAA is not up and running as of yet with this switch).
I'm trying to change the default name on my Sky router but when I try a pop up from Windows security is asking for my username and password which I don't have as I never set one up in the first place! is this the default password from Sky, Admin- Sky that I need to use?
I rdp into our server 2008 via IP. This is a router on ip 0.1, this is forwarded to my server on IP 0.3. This server was setup with DHCP default gateway of 0.1. We added a new outside connection on IP 0.2. I was talked through the changes so that internal DHCP requests went to gateway IP 0.2 but RDP still used 0.1. I plan on getting rid of 0.1.Where is the setting to change the RDP to use default gateway of 0.2?
I would like the ability to change the default password. Currently, when I change the default password and save the config via the web interface, neither the original password, or the new password work. I am forced to reset the device to the default config to regain access to the device.
I have been net searching this question and I find answers relative to other Cisco products but not for the 6500 series. We are running entservicesk9_wan-mz.122-18.SXF17a.bin and would like to know how to change the default SSH listening port..
i forgot to change the default username and password of 1941 router. I have alos performed WR memory on router. When i am trying to recover it through ROMMON mode i am not getting the initial configuration Dialouge through which i can change the password . I have gone through all documents available through internet for recovering the same but unable to recover it.
Ive changed the IP address of a laptop to connect to the router with IP 192.168.15.1 but now want to change the router IP address from the defaul to another subnet, so that it is accessable with other workstations on the LAN, but I could not readily find the option to set the Ip address on the router.
I'm signed in with user admin.
I also wanted to add addiontal users. The help indicates there is a User List Add Entry option but from the Administration bar, the left hand menu option shows User Management & User Privileges options. On User Management, it is possible to change the 2 default user names, but I wanted to leve them and create new ones.
since my network (static ip, cameras, and other boxes) is set up using 10.0.0.xx. How do I change the default ip address on the Linksys e3500 wifi router to 10.0.0.xx?
Windows 7, WRT54G2 router. How do I change the default Linksys password from "admin" to something of my chosing? I appear not to have the Setup CD. Router is working well but it still has the original password.
The default value of DRAM and Flash memory are 128 MB and 16 MB of Cisco Catalyst WS-3750-24PS-E switch .I want to know , wherther the default value may be change upto 256 DRAM and 128 Flash.
I am currently setting up a 2800 Series router, and prefer a username/password type authentication rather than a single enable password. To do this, I did:
This basically does what I want - when I connect to the router through console, it immediately asks me for a username and password. The thing is - as soon as I provide the right credentials, it takes me to USER EXEC mode (the default command mode). Is it possible to change that so that after entering the credentials, I go right into privileged exec mode?
Bonus question: As it is now, I just have no enable password, so when I login with my credentials, I issue "enable" to enter privileged exec mode without it prompting for an additional password. Is it safe to do it this way - having no enable password but requiring a username and password for login?
don't have an option to connect a console cable to my cisco router. The usb to serial converter will not work in windows7 only on XP.have physical access to my 881 Cisco Router. If I remember correctly these routers have a default ip address. This router is brand new, out of the box. I am thinking I can access it with the correct IP via network instead of console.
There are two issues which are testing my resolve.
1) Bad Cryptochecksum Ignored error 2) Unable to boot to a save startup-config file.
I want to take the configuration from one ASA 5505 and move it to another ASA 5505. I copied the startup-config file from an ASA 5505 running asa821-k8.bin to an ASA running 8.222-k8 to flash using tftp. I set the boot config parameter on the new asa to flash:/startup-config which is the location of the startup file. If I use copy run start command, I over write the startup file. When I copy the startup configuration to the running configuration I get a Bad Cryptochecksum Ignored error and the startup file does not copy over to the running file. How can I resolve this issue?
We have a 861 router for our small office with 15 people. We have been experienced download problems for several months, but we have suspected the internet supplier to be the bottleneck as we have a new 861 router with the default configuration from the "Cisco Configuration Professional Express".
The sympton is that the download speed over http starts fast, but drops after a few seconds from 10MB/s to 3KB/s and stays there. The internet supplier came here today and made some tests. So we downloaded some huge files over the direct cable, and it was staying at constant 10MB/s. When we connected over the router it started at 10MB/s and dropped down to 3KB/s.
Is there something that has been forgotten in the "Cisco Configuration Professional Express"?
What is the purpose of these default configuration lines? What do they mean? I can't find an explanation of them anywhere. I believe some are written to the config when FCoE is enabled..
I would like to know exactly what they are doing.
class-map type qos class-fcoe class-map type queuing class-fcoe match qos-group 1
I can SSH from the internet to my ASA on default port 22, directly to my public IP. I can SSH from the internet to my Cisco 1841 on port 2001. I can not however, SSH to my Cat 2960. From what i can tell, on the Cat2960 i can't change the default port 22 for SSH to different port, just like i did on the Cisco 1841. I looked to see if I can change the default port for SSH on he ASA, it does not look like this is an option.
The bottom line is that i want to be able to SSH to all three devices from the internet. I only have one public IP. As of now, what i can do is only SSH to the ASA on default port 22 directly to the public IP and Cisco 1841 on port 2001. It appears that changing the default SSH port on Cat 2960 is not an option. It also appears that I can't change the default SSH port on the ASA, if i could, i would and then i should be able to SSH to the Cat 2960 on port 22. No matter what i did on the ASA, it always listens on port 22 for SSH connections.
show asp table socket TCP 001f549f <<pub IP>>:22 0.0.0.0:* LISTEN
how do i make it listen on different port?
Here is relevent config for SSH for cisco 1841 (port forwarding)
We have 3 WAP4410N on our network. Our laptops pick them up but I cannot access the configuration Utility or ping the default IP address. If their IP addresses have been changed how do I find out what their current IP adds are? We currently use static IP addressing for our network.
I have had a WRV200 wireless router running at the family office now for a several years now and recently I was made aware of an issue with the router. Previously it's function was to provide internet access for the laptops at the office and two workstations. It was a simple set up really, 1 SSID was for the work computers that were allowed on the internet and another SSID for personal and quest wireless devices and I made sure they were in seperate VLANs. This issue came into light after our office moved and with some new upgrades in networking equipment it was deemed safe enough to have the other computers on my wireless router.
What is happening is that all the computers will have a momentary drop of connectivity and will re-establish it's connection to the wireless router. I check the event viewer and it's the same thing accross the board. I'll have several DHCP warings specifically event ID 1003 and finally DHCP error 1000 almost 30 minutes after the first warning. From the looks of it there is something going on with the DHCP addresses about to expire and the systems are having issues trying to get it renewed. The error will happen then the computer will restore the connection.
I have it isolated to the WRV200 because of two reasons. Every machine is having this issue, it's not a random occurance on one computer. The big clue was when I checked Event viewer on my Marketing Director's laptop. These same errors were present all the way back to May which was before the office move and the router was provide access for our laptops to get online. There was no other networking equipment connected to it except for the Clearwire modem.
Between May and now the router has been reconfigured from scratch. New SSIDs, redid the internal IP addressing network wide to incorporate the new computers and would be easier to manage them that way. All wired devices go through a 16 port switch and then through port 1 on the router. Port 1 is on VLAN 1 and the others on VLAN 5. The 3 SSIDS are each on their own seperate VLANs. All systems are on DHCP and the important computers and the printers I am using Static DHCP. In the mean time I set all the important machines to use an alternate IP addressing scheme so hopefully there is no drop in conenctivity. While the drop is minor it could cause issues in the program called SLS (especially during printing) so I can not have this issue to continue. Configuration wise everything is defualt, is there something to change in the configuration settings that I may have missed twice now or the router simply near the end of it's life cycle.
One of our ASA5510s lost VPN site-to-site connectivity (ASA v8.2(2); ASDM v6.2(5)53) to one of our other sites last night. The checkbox for Access Interfaces on the Site-to-Site area in Connection Profiles lost its checkbox for the external interface.
3750 switch connects to Blade-switch_1 and Blade-switch_2 Spanning-tree mode is configured as rapid-pvst on 3750 switch, do I need to configure rapid-pvst on both blade-switches or keep the default pvst config.3750 is running VTP domain HQ and transparent mode Both Blade_switches are running VTP domain CLI and transparent mode To configure Etherchannel between 3750 and blade-switch_1 do I need to have all devices in same vtp domain?
We have a Windows XP machine on our network that is giving us a strange problem. We have it statically configured with an IP and a default gateway address which points to a router on our network. This is the same router that nearly all of our machines point to and none of the other machines have this issue.If we open up CMD and make a ping request from an outside server (public or interal servers on other subnets) we get a 'destination host unreachable' error. We can ping the ip address of the router that is assigned as the default gateway. We can circumvent this ip address by adding a static route ('route add' from CMD) directing all traffic on the network interface to the ip of the router. Once this is done we can ping and get a response from any server both internal and external. We also tried doing a tracert (without have the static route added) to an external site by IP address. The tracert does not even show a hop for the router so it seems as if the request is never making it past the interface on the XP machine. We simply get an error saying it is unable to find the host. Interesting though it does provide us with a domain name for the ip address. So somehow it is able to reslove DNS. (We have a local DNS server on the same subnet)
We have installed a WLC440 at a school with 30 1131 APs. Only 3 showed up under Wireless tab, and others became rogue APs. Where and/or what do I need to change on the configuration for others to join properly? Have matched the configuration on this WLC with other WLC at the other schools, and still not able to find out where the problem is.
we just replace 6500 with N7K, after migration there're some device (server,pc,printer) change its ip address configuration (subnet and gateway) by it self. can N7K did it?
I bought this wireless router the other day in order to get internet access on my Nintendo Wii. I set it up using the CD and followed all the instructions (made a password, wrote down the key, etc.) - and my Wii CAN detect it, but when I type in the key on the Wii I get an error message. I looked online and they said the way to fix that specific error is to "change the channel" on the router to 1 or 11. (It is currently 6). I type in my IP into the browser like I'm supposed to (the default IP of the router), but ALL the options on the page are greyed out and nothing is click-able. Here's a screenshot
I planned for my customer to replace his old LMS 4.0.1 server under Windows 2003 by a new server under Windows 2008 R2.Customer wants also to set a new LMS name and IP address for the new server under Windows 2008 R2 and keep both servers on the network.I'm wondering what could be the best procedure to do that migration.Can I used backup / restore procedure in that case ?If yes, what file must I modify to adapt the new LMS configuration to new hostname and IP Address ?
he has the same problem "default gateway is not available" on his Acer laptop with Windows 7, so we were psyched to find this problem posted - and today even (weird?). However, we tried resetting the : netsh winsock reset catalog etc and rebooted but still no internet access.
