Cisco Routers :: 2800 - Change Default Command Mode To Privileged EXEC?
Feb 14, 2013
I am currently setting up a 2800 Series router, and prefer a username/password type authentication rather than a single enable password. To do this, I did:
Router(config)# username <myuser> privilege 15 secret 0 <mypassword>
Router(config)# username2 <myuser> privilege 15 secret 0 <mypassword>
Router(config)# aaa new-model
Router(config)# aaa authentication login default local
This basically does what I want - when I connect to the router through console, it immediately asks me for a username and password. The thing is - as soon as I provide the right credentials, it takes me to USER EXEC mode (the default command mode). Is it possible to change that so that after entering the credentials, I go right into privileged exec mode?
Bonus question: As it is now, I just have no enable password, so when I login with my credentials, I issue "enable" to enter privileged exec mode without it prompting for an additional password. Is it safe to do it this way - having no enable password but requiring a username and password for login?
View 3 Replies
ADVERTISEMENT
Mar 27, 2011
Is there a way to configure a ASA 5500 firewall so that when i access the firewall via SSH, my user is in privileged exec mode immediately after i have entered the log in credentials? So no need to enter "enable" anymore. I know how to do that with a router but couldn't figure it out for the ASA.
View 2 Replies
View Related
Jul 12, 2012
I recently configured a Cisco AP 1242, software version 12.4, via the web interface using the default Cisco credentials. At that time I setup an administrator account with read/write access and changed the Cisco to a read only access. Now went I attempt to login to the web interface it won't accept the administrator password. It will except the administrator password in a telnet session however. So via the telnet session I setup another user with privileged exec level access and that wont work on the web interface either. The Login box keeps coming back requesting a password. Strangely enough, I can login to the web Interface using admin username, with the Cisco password; but I can't do anything, and I also can't view everything. I've tried the following:
I've turned on SSH and created a certificate in the AP, but the login box continues to pop on the https://url.I've attempted to setup a user with a non-encrypted password, but have been unsuccessful.I've tried a different browser - login box continues to pop.I've made sure the web interface is activated in the API've tried a differnet computerI've tried disabling password-encryption service. Reset the enable password , I've successfully setup other 1240 APs but must have done something wrong on this one.
View 1 Replies
View Related
Oct 2, 2011
Cisco cannot login? Currently i cannot login to the two of my cisco 3560 with the password that i usually used to login. and it is strength to me that its Configuration register is 0xF.
[BEGIN] 10/4/2011 10:22:57 AMshoTC-NGN-C3560-1>show verTC-NGN-C3560-1>show version Cisco IOS Software, C3560 Software (C3560-IPSERVICES-M), Version 12.2(35)SE5, RELEASE SOFTWARE (fc1)Copyright (c) 1986-2007 by Cisco Systems, Inc.Compiled Thu 19-Jul-07 18:15 by nachenImage text-base: 0x00003000, data-base: 0x01300000
ROM: Bootstrap program is C3560 boot loaderBOOTLDR: C3560 Boot Loader (C3560-HBOOT-M) Version 12.2(25r)SEC, RELEASE SOFTWARE (fc4)
TC-NGN-C3560-1 uptime is 50 weeks, 6 days, 9 hours, 34 minutesSystem returned to ROM by power-onSystem image file is "flash:c3560-ipservices-mz.122-35.SE5/c3560-ipservices-mz.122-35.SE5.bin"
[code]....
View 1 Replies
View Related
Aug 22, 2011
I'm trying to configure ASA 5550 t8.4 so, that ssh and https access users would authenticate themselves vs Radius (or LDAP) server and they would be directly logged in with privilege mode 15.
I have Windows 2008 NTP acting as RADIUS server. And the network policy is: Service-Type - Login, Vendor-Specific - shell:priv-lvl=15 and allow full network access. All my AP's and switches with IOS are able to use that policy and i am able to get directly to exec mode (privilege lvl 15)
But on ASA, the user has to "enable" itself.
ASA conf:
#aaa-server <group name> protocol radius#aaa-server <group name> (inside) host <ip address> key 013B072C5A26070B2475411C350A18192218313A6A671F1A1B
#(config)aaa authentication ssh console <group name> LOCAL
#(config)aaa authentication http console <group name> LOCAL
How to get authorization working with LDAP (Active Directory)?
View 2 Replies
View Related
Nov 11, 2012
I am experiencing a problem that when I telnet a router ip.It prompts for username and password.After entering username and password the router enter into exec mode with > prompt.But when trying to enter in privilege exec mode by typing en or enable it gives error:
"Translating "en" %unknown command or computer name.or unable to find computer address".
This problem started on removing easy vpn configuration which include aaa new model configurations. The router is in production environment and have remote and console access.
View 11 Replies
View Related
Jul 2, 2012
I've got very basic problem but I cannot find the solution... I am sitting on the Cisco 4948E switch. And, I wanted to allow to guys who have not enable password to issue command sh running-config.I used the the following command to do that:SW4948E(config)#privilege exec level 1 show running-config.
View 3 Replies
View Related
Jul 5, 2011
how to straight away enter priv EXEC mode when authenticated for asr1002?? Using XR12000, it can be done but asr1002 have to input enable passwd...my username for asr1002 have privilege 15 and i want to enter priv EXEC mode straight away after login without asking the enable passwd.
View 4 Replies
View Related
May 12, 2013
Ive changed the IP address of a laptop to connect to the router with IP 192.168.15.1 but now want to change the router IP address from the defaul to another subnet, so that it is accessable with other workstations on the LAN, but I could not readily find the option to set the Ip address on the router.
I'm signed in with user admin.
I also wanted to add addiontal users. The help indicates there is a User List Add Entry option but from the Administration bar, the left hand menu option shows User Management & User Privileges options. On User Management, it is possible to change the 2 default user names, but I wanted to leve them and create new ones.
View 2 Replies
View Related
Nov 29, 2011
I have tried to change the username and password using the following procedure but when I do so and reboot the router and try to login using the new userid and password it says Authentication failed. Complete these steps in order to recover your password:Shut down the router.Remove the compact flash that is at the back of the router.Power on the router.Once the Rommon1> prompt appears, enter this command:confreg 0x2142Insert the compact flash.Type reset.when you are prompted to enter the initial configuration, type No, and press Enter.At the Router> prompt, type enable.At the Router# prompt, enter the configure memory command, and press Enter in order to copy the startup configuration to the running configuration.Use the config t command in order to enter global configuration mode.Use this command in order to create a new user name and password:router(config)#username cisco privilege 15 password ciscoUse this command in order to change the boot statement:config-register x2102Use this command in order to save the configuration:write memoryReload the router, and then use the new user name and password to log in to the router.
View 16 Replies
View Related
Jan 25, 2013
My Cisco seems to be stuck when it boots up, with the following:
Upgrade ROMMON initalized
And it goes on with self comperessing image then an OK but then it starts loading again all over.
View 13 Replies
View Related
Mar 27, 2013
I'm really not clear about default-gateway on switch command, not the function but how its works.i have 1 multilayer switch (MLS 1) that have 2 vlan within it, vlan 2 and 100. on vlan 2 i assign ip address of 192.168.1.1 and on vlan 100 is 172.16.1.254. both vlans are up. then under that multilayer switch i added 2 more MLS (MLS 2 and MLS 3), and the links of MLS 2 and 3 to MLS 1 are trunking. and both MLS 2 and 3 have a same vlan with MLS 1. that i assign an ip address on vlan 2 in MLS 2 192.168.1.2 and i set default gateway 192.168.1.1, and i do the same to MLS 3 but the ip address of vlan 2 is 192.168.1.3i already setup the routing protocol on MLS 1 so that vlan 2 could contact vlan 100. but the fact it doesnt work at all, both MLS 2 and 3 cannot contact vlan 100 eventhough that are already have default-gateway setup, is there anything wrong with the configuration ??
View 3 Replies
View Related
Jun 5, 2013
I have an 877 router which has a DSL WAN interface. The DSL service at this site is unreliable, so the company have purchased a separate 3G router to be used as a backup. This device maintains 3G connectivity at all times and has a static IP on the internal subnet (for arguments sake let's say 10.0.0.253).
What I want to do with the Cisco router is to track the DSL interface and if it is up, install a default route pointing to it. If it is down, I want the default route to be the 3G router.
I am thinking the best way to do this is to set up a track and then set 2 default routes; one which is installed if the tracking is up, the other has a higher admin distance and points to the 3G router and thus should only be used if the track is down. For example:
track 10 interface Dialer0 ip routing
delay down 30 up 30
ip route 0.0.0.0 0.0.0.0 Dialer0 track 10
ip route 0.0.0.0 0.0.0.0 10.0.0.253 100
Is this likely to work or is there a better way to do it?
View 7 Replies
View Related
Apr 18, 2013
I have 3560g with 15.0(2)SE2 version. I try to give different default gateways for different interfaces.I've already changed the sdm, run "ip routing" and made interest interfaces in "no switchport" with ip addresses.
my route-map is "
route-map ABC permit 10
set ip next-hop 192.168.77.3"
and it is applied on the interface with "ip policy route-map ABC" but when I try to apply it says "%PLATFORM_PBR-3-UNSUPPORTED_RMAP: Route-map ABC not supported for Policy-Based Routing" everything is fine if I change from "set ip default next-hop" to "set ip next-hop" but it is not I need in the guide of the version it is said this statement is not in unsupported list of route-map commands.[URL]
View 4 Replies
View Related
Mar 15, 2011
I have recently up swapped out an 877 router for an 887 router and have copied the config template accross however it will not take 3 of my commands.
AAA accounting system default stop-mly group tacas+
ip inspect name firewall cuseeme timeout 3600
dsl operating -mode auto
View 2 Replies
View Related
Feb 20, 2012
Can we set ips 4260 into factory default settings with a single command?
View 0 Replies
View Related
Jun 26, 2012
when will be the command "default interface x/x" on the Nexus 5000 platform available? Even with latest software version (5.1.3.N2.1a) it is not possible. For Nexus7000 it's working fine with 5.2 train.Is there a feature request for it? If not here it is!!It's horrible to deconfigure many interfaces especially in N5k environments with many FEXes.
View 3 Replies
View Related
Apr 16, 2012
recently i do some lab about trunking protocol using Layer 3 switch C3560 and layer 2 switch C2960, but i face a problem that i cannot configure trunk port on my C3560 using "switchport mode trunk" command, and after looking for the answer from google i found that i have to "remove" the "auto" mode of C3560 using "switchport mode dynamic desirable" and after that we can enter the "switcport mode trunk" command successfully.
and my question are, whether the "auto" trunk mode in switch layer 3 is a default mode or not? and why i should enter "sw mode dynamic desirable" command before "sw mo trunk" command ?
View 5 Replies
View Related
Jul 17, 2012
I'm trying to change the default name on my Sky router but when I try a pop up from Windows security is asking for my username and password which I don't have as I never set one up in the first place! is this the default password from Sky, Admin- Sky that I need to use?
View 1 Replies
View Related
Sep 19, 2011
I am trying to implement RBSCP on two 3845s running 15.1(4)M1 Adv Enterprise over a satellite link. The "show" commands all look correct, but whenever I policy route my machine through the RBSCP tunnel I dont even make it to the opposite side. However, if I remove the "tunnel mode RBSCP" command so it acts like a regular GRE tunnel, I route through it just fine. So I know its not a NAT, routing issue. [code]
View 1 Replies
View Related
Oct 22, 2012
Need to confirm purpose of command below
dot11 ssid TEST
vlan 4
authentication open
authentication key-management wpa
guest-mode ?????
Why we need guest-mode command in above config?
View 5 Replies
View Related
Oct 11, 2011
I rdp into our server 2008 via IP. This is a router on ip 0.1, this is forwarded to my server on IP 0.3. This server was setup with DHCP default gateway of 0.1. We added a new outside connection on IP 0.2. I was talked through the changes so that internal DHCP requests went to gateway IP 0.2 but RDP still used 0.1. I plan on getting rid of 0.1.Where is the setting to change the RDP to use default gateway of 0.2?
View 3 Replies
View Related
May 3, 2013
i have 4507R with dual supervisors (WS-X4013+10GE) with IOS cat4500-ipbasek9-mz.122-46.SG.bin the supervisor module are in 3 and 4, and I want to connection port 5, but i have interface and line protocol down "inactive" error.
So I realized to use command "hw-module" to change the module to GE port. However, I am not able to use the command as" I cannot use the command "hw-module uplink" as well.
View 2 Replies
View Related
Apr 13, 2011
I was wondering about command of Linkset subcommand at ITP7613.I have been using the Cisco7613 chassis for the ITP(SIGTRAN) service.
However, i know that the "tx-queue-depth" command is used for sctp multihoming buffersize that between primary and secondary path at the Link sub-command mode. but i can't adjust the changeover buffersize(retrieval buffer) that between link and another link at the Linkset subcommand mode.
It's above my comprehension.
My guess is that related to "plan-capacity-rcvd" command. it's right?I want to know command that adjust the buffersize of Link changeover.
View 0 Replies
View Related
Aug 18, 2011
I recenly installed LMS 4 on a windows 2008 R2 system , I didnt change the default configuration of windows or ciscoworks.I just added devices and configured basic things on the LMS system .when I open ciscoworks on the server itself it starts a browser session on http port 1741 and then changes automatically to https even though the default config is browser security disabled on ciscoworks.I try to open a browser session on a mgmt station to the cisco server , it didnt work in https ( I did get the login screen but couldnt log on , probablly something to do with the certificate ) , so I open http on port 1741 and it worked , I was able to log in .After a few Hours for some strange reason I didnt have access any more from the mgmt station not in http nor in https , the only way was to access it from the server itself.I went and changed the default setting of the secure browser on LMS 4 hopping that would work , I was asked to restart the ciscoworks service for the changes to take affect , I tried to restart it but it was unsuccesful so I restart the whole server. when it came up ciscoworks didnt work most services didnt start ( like the web server ,tomcat and all the manual services and ciscoworks deamon)
View 1 Replies
View Related
Jul 23, 2012
I tried to change the default password Cisco to other by command line but the password cannot work out.
The command line I used are as below :
AP#conf tEnter configuration commands, one per line. End with CNTL/Z.AP(config)#enable passAP(config)#enable password 4dMINO123 ?LINE <cr>
[Code].....
View 10 Replies
View Related
Jun 1, 2011
How do I personalize the settings on my router from default. Netgear wnr2000.
View 2 Replies
View Related
Sep 2, 2012
I would like to change the default ip address on my netopia 3347 frrom 192.168.1.whatever to 192.168.0.whatever
View 2 Replies
View Related
Apr 1, 2012
How can I change the camera name form the default which is the same as the model name
View 1 Replies
View Related
Dec 30, 2011
I would like the ability to change the default password. Currently, when I change the default password and save the config via the web interface, neither the original password, or the new password work. I am forced to reset the device to the default config to regain access to the device.
DCS-930L firmware 1.04 and Mac OSX 10.5.8
View 12 Replies
View Related
Oct 12, 2011
I am switching a switch connecting to the ASA5550 tomorrow. My current switch is using fiber connecting to the ASA. The new one only support copper. If I switch between fiber to copper on the ASA (change media-type command on interface) will it cause a down time? I have VPN tunnel on the ASA and don't want the session to reset.
View 2 Replies
View Related
Jun 6, 2012
if ACE SM in L2 mode need the default gateway? We're running v. 3.2a.
View 8 Replies
View Related
Jul 17, 2011
I have been net searching this question and I find answers relative to other Cisco products but not for the 6500 series. We are running entservicesk9_wan-mz.122-18.SXF17a.bin and would like to know how to change the default SSH listening port..
View 1 Replies
View Related
