Cisco WAN :: 877 - Privilege Exec Mode
Nov 11, 2012
I am experiencing a problem that when I telnet a router ip.It prompts for username and password.After entering username and password the router enter into exec mode with > prompt.But when trying to enter in privilege exec mode by typing en or enable it gives error:
"Translating "en" %unknown command or computer name.or unable to find computer address".
This problem started on removing easy vpn configuration which include aaa new model configurations. The router is in production environment and have remote and console access.
View 11 Replies
ADVERTISEMENT
Aug 10, 2011
I have a customer with a 861 ISR.I want to block all the privilege 0 users from access the enable command
If i telnet into the device, as a priv=0, enable does not work
If i telnet into the device, as a priv=15, enable does work
If i telnet into the device, as a priv=0, enable does not work
If i telnet into the device, as a priv=15, enable does not work
I have issued the command:privilege exec level 15 enable Should block everyone except 15's from accessing the enable command SSH and TELNET are on the same vty:
line con 0
login authentication local_authen
no modem enable
line aux 0
line vty 0 3
[code]....
Basically TELNET is following the rules ( priv=0 not allowed to access enable ) but SSH is not following the rules ( both priv=15 and priv=0 cannot access the command ) is there a way from blocking somes users from login in completely?
View 9 Replies
View Related
Jul 2, 2012
I've got very basic problem but I cannot find the solution... I am sitting on the Cisco 4948E switch. And, I wanted to allow to guys who have not enable password to issue command sh running-config.I used the the following command to do that:SW4948E(config)#privilege exec level 1 show running-config.
View 3 Replies
View Related
Mar 27, 2011
Is there a way to configure a ASA 5500 firewall so that when i access the firewall via SSH, my user is in privileged exec mode immediately after i have entered the log in credentials? So no need to enter "enable" anymore. I know how to do that with a router but couldn't figure it out for the ASA.
View 2 Replies
View Related
Jul 5, 2011
how to straight away enter priv EXEC mode when authenticated for asr1002?? Using XR12000, it can be done but asr1002 have to input enable passwd...my username for asr1002 have privilege 15 and i want to enter priv EXEC mode straight away after login without asking the enable passwd.
View 4 Replies
View Related
Feb 14, 2013
I am currently setting up a 2800 Series router, and prefer a username/password type authentication rather than a single enable password. To do this, I did:
Router(config)# username <myuser> privilege 15 secret 0 <mypassword>
Router(config)# username2 <myuser> privilege 15 secret 0 <mypassword>
Router(config)# aaa new-model
Router(config)# aaa authentication login default local
This basically does what I want - when I connect to the router through console, it immediately asks me for a username and password. The thing is - as soon as I provide the right credentials, it takes me to USER EXEC mode (the default command mode). Is it possible to change that so that after entering the credentials, I go right into privileged exec mode?
Bonus question: As it is now, I just have no enable password, so when I login with my credentials, I issue "enable" to enter privileged exec mode without it prompting for an additional password. Is it safe to do it this way - having no enable password but requiring a username and password for login?
View 3 Replies
View Related
Apr 10, 2013
There was this router Cisco 815 that i consoled. I cannot go into its privilege mode. even typing enable still cant go to its # mode. whats the problem with this router? how am i able to fix it? its initial problem was it cannot carry more pc client anymore.. 815 series has a 4 switch port at its back and a wan port.the 4 switch port cannot access the internet if connected to 4 pc clients.
View 5 Replies
View Related
Dec 18, 2012
I have created users and given them telnet access to router 7200. They have full privilges(15) but everytime they login they login into user-exec mode instead of privilege mode. Is there a way to skip user-exec mode and allow the users to login directly into privilge mode so they dont have to enter password twice?
View 2 Replies
View Related
Sep 6, 2012
I have added Cisco 5520 into the Cisco ACS 4.2 Tacacs Server. I can login to the user mode, but I can't login to the privilege mode ? though I have put enable password, but when I use that password, no joy ?
View 3 Replies
View Related
Nov 17, 2011
I have my first 3560x running IOS 15.0(1)SE and noticed that I can no longer login to privilege mode even though my use account is setup with privilege 15. I have the exact same setup on 12.2 (53)SE2 and have no issue, so has something changed?
View 4 Replies
View Related
Aug 26, 2007
I tried to authenticate and authorized Nokia/checkpoint Nortel/AD3 and Nortel 5510 platform using an 4.1 for windows ACS. the ACCESS-REQUEST is well processed bi the radius server wich send ACCESS-ACCEPT to the AAA Client (ie NORTEL or NOKIA), but i'have got privilege access denied on the Client side. RADIUS IETF Dictionnary is used for every device. all others Cisco Devices authenticate and are well authorized.
View 3 Replies
View Related
Mar 14, 2013
I have a pair of ASA 5520 firewalls running in active/standby mode on 8.3.2.34 code. My configuration performs authentication/authorization into ACS 5.1, however command authorization is failing when I try to execute a command on the standby from the active unit...
failover exec standby dir disk0:/
Fallback authorization. Username 'adminuser' not in LOCAL database Command authorization failed
I don't even see the authentication attempt going into ACS.
View 2 Replies
View Related
Jul 12, 2012
I recently configured a Cisco AP 1242, software version 12.4, via the web interface using the default Cisco credentials. At that time I setup an administrator account with read/write access and changed the Cisco to a read only access. Now went I attempt to login to the web interface it won't accept the administrator password. It will except the administrator password in a telnet session however. So via the telnet session I setup another user with privileged exec level access and that wont work on the web interface either. The Login box keeps coming back requesting a password. Strangely enough, I can login to the web Interface using admin username, with the Cisco password; but I can't do anything, and I also can't view everything. I've tried the following:
I've turned on SSH and created a certificate in the AP, but the login box continues to pop on the https://url.I've attempted to setup a user with a non-encrypted password, but have been unsuccessful.I've tried a different browser - login box continues to pop.I've made sure the web interface is activated in the API've tried a differnet computerI've tried disabling password-encryption service. Reset the enable password , I've successfully setup other 1240 APs but must have done something wrong on this one.
View 1 Replies
View Related
Jun 4, 2011
I have created internal user on internal identiy store --> users with password & enable password , Similarly i have enabled max privilige level 15 under policy elements , authorisation & permission ,Device administration , shell profile .But i am unable to login into device using enable password , I am finding following error on my logg report
Failuire reason : 13029 Requested privilige level is too high .
View 3 Replies
View Related
Apr 11, 2012
im having confused with those command "username (username) privilege (0-15) secret 5 (word)", what should i put into (word) part ?cause when i tried to put a "cisco" an error comes up. "privilege" command function and how that commands work?
View 4 Replies
View Related
Jun 13, 2011
I have cisco ACS 5.2 and external identity source as RSA secure ID.Currently when the RSA user login to AAA Network devices, User id & passcode prompt coming after giving the credential its going to user exec mode.Then after "enable" command again asking for Passcode giving passcode then user able to logged in successfully.
I need RSA users to get direct privlege level15 (privlege mode) ? no need to ask enable password ?
I checked this for local ACS users it is working and loca users getting directly privelege mode access...
View 2 Replies
View Related
Feb 15, 2013
We have more than 50 devices handling by PI 1.2 (testing) I like to know how to do configuration archiving with user who doesn't have write privilege.
I tried like this.
username john privilege 6 password cisco privilege exec level 6 show running-config
(result) show run --> blank
I tried this user with one of switch in PI 1.2. It did not do configuration backup
username inout password inout username inout privilege 15 autocommand show running-config
(result) once logged in, it automatically showed running-config. However when I tried with PI 1.2 with this user (inout). I couldn't do configuration back.
reference [URL]
create certain user with read-only privilege while PI 1.2 is able to do configuration archiving ?
View 0 Replies
View Related
Dec 1, 2011
my admin user is still being assigned privilege level 1, as shown in AAA Protocol > TACACS+ Authentication Details report.The report seems to show that the user is getting the right shell profile (Selected Shell Profile: Net-Admin -- is the one I setup for this user's group with both Default Privilege and Maximum Privilege set to Static 15). But still not the right privilege (Privilege Level: 1).Also, I found this document via Google: [URL] The router configuration examples all show this "aaa authorization exec tacacs+|radius local" command, which my device does not have.So I am wondering if I am not reading the ACS report right, or the device actually was assigned the correct privilge but that does not work without the "aaa authorization exec" command in the configuration?
View 1 Replies
View Related
Apr 29, 2011
I can't seem to enable in ASA with a non-15 privilege level user configured in ACS 4.2 (tacacs).When I enable in IOS device, it enables and "show privilege" shows level 10 as expected. ACS should be configured correctly as it works fine with IOS. User is not set with explicit settings. Group is set with "max enable level" 15 and "shell exec priv level" 15. The enable password is set to the internal ACS PAP password. Works fine in IOS.When I enable in ASA, it fails to enable, and ACS log says "Tacacs+ enable privilege too low". I suspect that ASA tries to enable into level 15 explicitely. If I try to issue "enable 10" command in ASA it says: Enabling to privilege levels is not allowed when configured for AAA authentication. Use 'enable' only. [code]
View 2 Replies
View Related
Sep 21, 2011
We have an ADSM (version 5.2(3) ) . In ASA ( version 7.2(3)) we are working with routing, access restriction and configuring IPSEC vpn with integration to our AD. We need to get two diferent profiles: one for networking administrators, who are going to manage routing, acls and have the root for ASA, and the other profile is going to be for the vpn administrators. As I read from the ASDM 6.0 user guide is posible define command privilege level. So do you consider posible to define a particular level for all the command related with ipsec vpn (Create, Modify and Delete) and asociate that particular level with the user for vpn administration.
View 1 Replies
View Related
Sep 7, 2011
having LMS 4.0.1 is it possible to authenticate user on a group base and assign different privilege to different groups?. The user's group are available in the LDAP server.Do I have to use a TACACS/RADIUS server between the Ciscoworks LMS and the LDAP repository?
View 1 Replies
View Related
May 30, 2013
I have 2 local accounts on a 3750 that kick in should radius be unavailable. If I log in as the admin account it gets priv 15, if I log in as the other user it gets privilege 3 which is correct, by my commands dont work, this is what I have added and the strange thing is I've dont this many times before on our other switches
username admin privilege 15 secret ***
username users privilege 3 secret ***
aaa new-model
[Code]....
View 2 Replies
View Related
Oct 17, 2012
what is the minimun privilege level to assign at username account on ASA 5505 to grant the access with AnyConnect?
username ... privilege ?
View 4 Replies
View Related
Oct 4, 2011
In CLI we have users log in at priv 1 and use "enable" to increase privilege and do configurations. This allows "accounting" of command history. On the AIR-AP1121G-A-K9 (12.3(8)JED1) I cannot duplicate this for http login.
I can log in as a user at priv 1. When I try to go to a privileged link like "Security" I get prompted for a second login/pw. Nothing works here unless I have a second user defined at priv 15 and enter that login/pw. The problem is - that login/pw can be used to log in via http in the first place which bypasses accounting of the actual user. It also allows login to the CLI at priv 15 which I cannot permit.
username test1 secret 5 abcdxxx
username test2 privilege 15 secret 5 efghxxx
enable secret 5 ijklxxx(code)
View 1 Replies
View Related
Jul 14, 2011
I have FWSM's in Cat 6513's. I have a need to be able to session from the switch to the FWSM by using default account (not local user), at privilege level 15 I further have a need to allow a user read only access by ssh'n into the FWSM...
I believe I need to setup a local user, at, say privilege level 5, assign the show command only to privilege level 5, then set the authorization command for that user. So, i think my command sets are as follows to accomplish this:
username <username> password <pw> priv 5
priv command level 5 mode exec command show
aaa auth ssh console LOCAL
aaa auth enable console LOCAL
aaa authorization command LOCAL
I think, that this will allow the user at privilege 5 to run only the show command and only by SSH to the FWSM while allow the priv 15 level default login to continue to function properly.
View 1 Replies
View Related
May 15, 2012
i am running NX-OS image n5000-uk9.5.1.3.N1.1.bin on the nexus 5020 platform.i have configured authorization with tacacs+ on ACS server version 5.2 with fall back to switch local database.a user test with priv 15 is craeted on ACS server, password test2 everything works fine, until i create the same username on the local database with privilege 0. ( it doesnt matter if the user in local database was created before user in ACS or after ) e.g.: username test password test1 role priv-0 (note passwords are different for users in both databases)
after i create the same user in local database with privilege 0,if i try to connect to the switch with this username test and password defined on ACS, i get only privilege 0 authorization, regardless, that ACS server is up and it should be primary way to authenticate and authorizate the user.
View 3 Replies
View Related
Mar 11, 2013
I´m looking for the best configuration to restrict a user to read-only. The restriction should be configured via CLI not TACACS+.
-Hardware: 3750 (probably not interesting for this question)
-Oldest IOS: 12.2(53)SE1
The user should be allowed to: see the running-configurationtrigger all kinds of show-commandsping and traceroute from the device.The user should not be allowed to: upload/delete/rename files on the flash-memoryget into level 15 (not sure if I can avoid this)all other commands despite those from level 1 and those specified above.
View 2 Replies
View Related
Nov 6, 2011
I want to create a user who only has access to "router>" prompt on the CLI. this user should not be able to do enable command and by no other means be able to go to global configuration mode. I know the command router(conf t)# username ABC privilege 1 password ABCPASS, but even with this command, this user gets privilege 15 access.
View 2 Replies
View Related
Sep 16, 2012
I got an ASA 5510 system currently in single context mode, with CSC SSM installed. Single ISP uplink to internet, no VPN. And now customer would like add another ISP uplink, without invest another box for HA.What come across my mind is make the current box into multi context. There's some area i need to concern and also need yours perspective on it.
Question 1: For making the firewall into multi context, am i need to do it from scratch, issue mode multiple command. Then rebuilt the current production config into one of the context, then another context meant for the new IPS uplink, and one admin context?
Question 2: For CSC -SSM licensing requirement, model ASA 5510 with security plus license is able to support 2 context. So if i split my firewall like what i mention in question, what exactly number of context do i own (admin, context A, context B)?
Question 3: For CSC-SSM module in multi context mode, so the management port of CSC SSM must attach at admin context?
Question 4: After configured all the policy and traffic to scan, how exactly i should do in order apply this policy to the interface? Should i only enable at admin context, then firewall service-policy rules, and apply it global, OR should i also do the same action on context A and Context B?
View 3 Replies
View Related
Mar 4, 2012
We have recently converted 1 Cisco Lightweight AP 1041 to Autonomous mode for site-survey purposes. We now want to convert it back to lightweight mode.
View 1 Replies
View Related
Mar 12, 2013
I received the following info from Cisco's TAC and wanted to inquire further before I start reconfiguring the switch:
In a redundant Sup-6E setup, the following configuration is supported :
- 1 TenGig uplink on Active Sup and 1 TenGig uplink on Standby Sup
- 1 TenGig uplink on Active Sup and 2 Gig uplinks on Standby Sup
- 2 Gig uplinks on Active Sup and 1 TenGig uplink on Standby Sup
- 2 Gig uplink on Active Sup and 2 Gig uplinks on Standby Sup
If you invoke shared backplane mode, the following configuration can also be supported:
- 2 TenGig uplinks(blocking) on Active Sup and 2 TenGig uplinks on Standby Sup
- 2 TenGig uplink(blocking) on Active Sup and 4 Gig uplinks on Standby Sup
- 4 Gig uplinks on Active Sup and 2 TenGig uplinks(blocking) on Standby Sup
- 4 Gig uplink on Active Sup and 4 Gig uplinks on Standby Sup
Here's the command and information about the "shared-backplane" mode :- [URL]
Currently, we have 2 SUP 6-Es(Module 5 - Active and Module 6 - Stand-by) setup in a redundent mode. I am planning on changing the redundent mode to the shared backplane mode so I can use 2 TenGig converters to uplink 2 access-switches. We purchased 2 TenGig converters and here is how I am planning on using them:
1- One will be used to uplink to two 3750 switches(stacked)
2- One will be used to uplink to a 2960 using a Gig SFP
My questions are:
1- Do I have to install the 2 TenGig converters(4-Gig Uplinks) in the same Module? Or can I use one one in module 5 and the second one in module 6?
2- Will changing the redundant mode to the shared backplane mode require rebooting the switch or disrupt the funtionality of the other linecards?
View 2 Replies
View Related
Feb 26, 2013
How can we know that 6500 and 7600 series switch and router are running in native mode or in hybrid mode.
View 2 Replies
View Related
Feb 19, 2013
I am not able to connect to any webpages in normal mode, even after restarting i still have the same problem [However it works in safe mode with networking]. The network connections show that it is connected and the signal strength is excellent. I then have to keep restarting the laptop like 3 to 4 times and it works. Its kind of frustrating to keep doing this all the time and besides i am scared by restarting the laptop so many time can harm it.
View 1 Replies
View Related
