Cisco AAA/Identity/Nac :: To Auto Enter Priv Exec Mode Upon Login On ASR1002
Jul 5, 2011
how to straight away enter priv EXEC mode when authenticated for asr1002?? Using XR12000, it can be done but asr1002 have to input enable passwd...my username for asr1002 have privilege 15 and i want to enter priv EXEC mode straight away after login without asking the enable passwd.
View 4 Replies
ADVERTISEMENT
May 28, 2012
I am having a ASR 1002 V 12.2(33)XND2t which is running on Tacas?I want when i login it shoudl directly go into the # prompt. I am not interested in typing enable on > prompt.
The configs are:
aa new-model
aaa authentication login default group tacacs+ local
aaa authentication enable default none
!aaa authorization console
!aaa authorization config-commands
[code]....
View 3 Replies
View Related
Nov 11, 2012
I am experiencing a problem that when I telnet a router ip.It prompts for username and password.After entering username and password the router enter into exec mode with > prompt.But when trying to enter in privilege exec mode by typing en or enable it gives error:
"Translating "en" %unknown command or computer name.or unable to find computer address".
This problem started on removing easy vpn configuration which include aaa new model configurations. The router is in production environment and have remote and console access.
View 11 Replies
View Related
Dec 30, 2012
I configured the below config in Routers it is working good , but when i do the same in SWITCH-2960 , i am getting a problem not able to login to enable mode ... i am getting the basic login only ....
Error msg : % Error in Authentication.
Need to be configured at TAFE Network Devices: Code...
View 4 Replies
View Related
Apr 14, 2013
I set up a DIR-655 router for a friend 4 years ago and it's worked reliably with all of their equipment since. They have wireless printers, iMacs, pc laptops and iPhone 4S's, all connecting without any problems. Recently, they got an iPhone5 and it will not connect to their home wireless automatically, they have to re-enter the password each time. They've tested their iPhone 5 on other networks and they do not have to re-enter the password. Apple and ATT are blaming the router. I do not live near them and I'm going to have to facilitate them remotely. At this point, I believe their router is configured with WPA2, but I can't be sure. Which configuration will work with the iPhone 5, as well as their other, older, devices that have worked for 4 years
View 1 Replies
View Related
Jul 2, 2012
I've got very basic problem but I cannot find the solution... I am sitting on the Cisco 4948E switch. And, I wanted to allow to guys who have not enable password to issue command sh running-config.I used the the following command to do that:SW4948E(config)#privilege exec level 1 show running-config.
View 3 Replies
View Related
Mar 27, 2011
Is there a way to configure a ASA 5500 firewall so that when i access the firewall via SSH, my user is in privileged exec mode immediately after i have entered the log in credentials? So no need to enter "enable" anymore. I know how to do that with a router but couldn't figure it out for the ASA.
View 2 Replies
View Related
Feb 14, 2013
I am currently setting up a 2800 Series router, and prefer a username/password type authentication rather than a single enable password. To do this, I did:
Router(config)# username <myuser> privilege 15 secret 0 <mypassword>
Router(config)# username2 <myuser> privilege 15 secret 0 <mypassword>
Router(config)# aaa new-model
Router(config)# aaa authentication login default local
This basically does what I want - when I connect to the router through console, it immediately asks me for a username and password. The thing is - as soon as I provide the right credentials, it takes me to USER EXEC mode (the default command mode). Is it possible to change that so that after entering the credentials, I go right into privileged exec mode?
Bonus question: As it is now, I just have no enable password, so when I login with my credentials, I issue "enable" to enter privileged exec mode without it prompting for an additional password. Is it safe to do it this way - having no enable password but requiring a username and password for login?
View 3 Replies
View Related
Jun 21, 2012
Why I can enter router login interface through 192.168.0.1 but can not enter through 192.168.1.1?
View 1 Replies
View Related
Mar 14, 2013
I have a pair of ASA 5520 firewalls running in active/standby mode on 8.3.2.34 code. My configuration performs authentication/authorization into ACS 5.1, however command authorization is failing when I try to execute a command on the standby from the active unit...
failover exec standby dir disk0:/
Fallback authorization. Username 'adminuser' not in LOCAL database Command authorization failed
I don't even see the authentication attempt going into ACS.
View 2 Replies
View Related
Apr 4, 2012
I upgrade to a Flash 32mbs memory stick, as I reboot the 2600 Cisco router, it appear in the ROMMON mode, nonetheless, I followed some wrong procedure by changing components on the ROMMON command line. however now the router reboot or start with symbol only V2V2v2a, and I can no longer enter the ROMMON Mode or key anything in. I have a copy of the IOS on my TFTP server.
[Code]....
View 3 Replies
View Related
Jun 4, 2013
Is it possible to use the mgmt port when in rommon mode? I use the Mgmt port when IOS is loaded and it works fine. I reboot the router, issue a break to put it in rommon and have set some variables but my Mgmt port never has link and I cannot ping it from the network. In rommon mode it looks like this:
PS1=rommon ! >
MCP_STARTUP_TRACEFLAGS=00000000:00000000
BOOT=bootflash:asr1000rp1-adventerprisek9.03.07.03.S.152-4.S3.bin,1;
IP_ADDRESS=10.71.50.101
IP_SUBNET_MASK=255.255.255.0
DEFAULT_GATEWAY=10.71.50.3
BSI=0
RANDOM_NUM=1133006948
RET_2_RTS=13:38:27 EDT Wed Jun 5 2013
RET_2_RCALTS=1370453907
?=0
View 3 Replies
View Related
Aug 12, 2011
how to enter dos mode in a windows pc without still remaining in windows interface.
View 8 Replies
View Related
Aug 19, 2011
I was battling why one machine was connecting to mapped drives correctly on reboot and someone else was not.Turns out if you use control userpasswords2 to turn on auto-login, then the network drives appear as disconnected on reboot.Turned off auto-login and it worked fine. Now this is an automated system that has to auto-login in case of a power outage.
View 2 Replies
View Related
Sep 14, 2011
I just received a Cisco Aironet 1130 AG wi-fi router to configure and when I entered the router through console, I am not able to get into config mode. It says:
AP588d.09a7.93e4#conf t
^
% Invalid input detected at '^' marker.
Also,
AP588d.09a7.93e4#sh start
startup-config is not present
Also, this is what I see in my flash:
AP588d.09a7.93e4#sh flash:
Directory of flash:/
3 -rwx 217 Mar 01 2002 00:07:10 +00:00 env_vars
4 drwx 128 Jan 01 1970 00:02:03 +00:00 c1130-rcvk9w8-mx.bin
I need to configure this device and set up for wi-fi access in my organisation network.
View 2 Replies
View Related
Sep 14, 2011
I just received a Cisco Aironet 1130 AG wi-fi router to configure and when I entered the router through console, I am not able to get into config mode. It says:
[code]....
View 9 Replies
View Related
Mar 17, 2012
How can I enter into "interface configuration" on Aironet 1130AG, AIR-LAP1042N?When I put following commands in enable conf tinterface Dot11Radio1 but, it fails and I cannot enter into "interface configuration".How can I do this ?The reason why I enter into conf tinterface Dot11Radio1 because I want to disable cdp via CLI ( serial console).
View 9 Replies
View Related
Jan 3, 2012
I have an ASA 5510 with IOS 8.4. I want that only authenticated active directory users can pass the firewall.
View 3 Replies
View Related
Jan 25, 2012
my RVS4000 is not renewing DHCP lease in Auto mode. Connection lost after 24 hours.
WAN Internet interface is physically connected to cable modem - Motorola SBV6120E. Setup as DHCP server. Cisco RVS4000 is obtaining DHCP public IP without any issue, the problem is that the connection drop every 24 hours and I need to release/renew DHCP each day to be able to communicate after 24 hours. After I loose connection I need to release DHCP, the WAN interface goes down and I need to renew DHCP then. I receive the same IP address and connection is againg UP and working.
tried to load new firmware and also setup the router with default configuration, but without any change. as there is no auto-reboot function, it is really annoying to log into managment interface each day. I also loose remote access after 24 hours, so I am not able to access the rotuer from outside. My local provider do not support static public IP on WAN, therefore I have to use DHCP.
View 2 Replies
View Related
Jun 11, 2012
We are facing to an annoying issue. We have a 6509 running in Catos 8.3(4) with WS-X6548-GE-TX, WS-X6348-RJ-45 and WS-X6148-RJ-45. When we configure the mode in auto negotiation, it comes up in half duplex. We need to configure the speed mode at 100Mbit/Full to make it work. But if the chassis or port restarts (not the server), the link becomes half duplex. This happens only on module in Gigabyte like WS-X6548-GE-TX.
Cable have been replaced but does not work. It is not happened on another chassis running on IOS 12.2(18)SXF17b with WS-X6548-GE-TX.
View 4 Replies
View Related
Oct 2, 2011
Cisco cannot login? Currently i cannot login to the two of my cisco 3560 with the password that i usually used to login. and it is strength to me that its Configuration register is 0xF.
[BEGIN] 10/4/2011 10:22:57 AMshoTC-NGN-C3560-1>show verTC-NGN-C3560-1>show version Cisco IOS Software, C3560 Software (C3560-IPSERVICES-M), Version 12.2(35)SE5, RELEASE SOFTWARE (fc1)Copyright (c) 1986-2007 by Cisco Systems, Inc.Compiled Thu 19-Jul-07 18:15 by nachenImage text-base: 0x00003000, data-base: 0x01300000
ROM: Bootstrap program is C3560 boot loaderBOOTLDR: C3560 Boot Loader (C3560-HBOOT-M) Version 12.2(25r)SEC, RELEASE SOFTWARE (fc4)
TC-NGN-C3560-1 uptime is 50 weeks, 6 days, 9 hours, 34 minutesSystem returned to ROM by power-onSystem image file is "flash:c3560-ipservices-mz.122-35.SE5/c3560-ipservices-mz.122-35.SE5.bin"
[code]....
View 1 Replies
View Related
Dec 18, 2012
I have created users and given them telnet access to router 7200. They have full privilges(15) but everytime they login they login into user-exec mode instead of privilege mode. Is there a way to skip user-exec mode and allow the users to login directly into privilge mode so they dont have to enter password twice?
View 2 Replies
View Related
Sep 6, 2012
I have added Cisco 5520 into the Cisco ACS 4.2 Tacacs Server. I can login to the user mode, but I can't login to the privilege mode ? though I have put enable password, but when I use that password, no joy ?
View 3 Replies
View Related
Nov 17, 2011
I have my first 3560x running IOS 15.0(1)SE and noticed that I can no longer login to privilege mode even though my use account is setup with privilege 15. I have the exact same setup on 12.2 (53)SE2 and have no issue, so has something changed?
View 4 Replies
View Related
Feb 12, 2012
how can I import a public or private key in a router? For example, a Cisco 3560th I have found some conflicting answers @ cisco.com . Background, I would like to login with PUTTY via ssh on a Cisco Router but without username and password.The login should be made with RSA Keys. For this I need to deposit on the IOS device's the public key and on my Client the private key. For this I've already created with PuTTYGen the two keys. The private is in the ppk format. I still need to convert this into a different format? Since there are PEM and PKCS. Below you can see what times I have entered. With the error message: "CRYPTO_PKI: Import PKCS12 operation failed, failure status = 0x705" With the following error message I can do anything?
View 2 Replies
View Related
Apr 24, 2011
I have two ACS 5.2 working in redundancy Primary and Secondary my question in when my primary ACS goes down i can´t see the log in the secondary ACS. I read in the documentación that only one ACS can be configurated for working like logg collector server. Now I configurated my secondary ACS like logg collector server now when my Primary ACS goes down i can see the logg. Finally when my Secondary ACS goes down i can modified the ACS Primary Configution by show me the logg.. Is possible to do this automaticaly for show me the event logg ? when the ACS that is configurate like logg collector server goes down pass the event other ACS automatically..
View 3 Replies
View Related
Jun 1, 2013
Few days ago in my wireless infrastrucer i deploy Cisco ACS 5.0 with Active directory integration. My wireless users are login through web authentication process. The authentication process is passed by AD & its working fine. But i want to do a work on my ACS 5.0 that a user cannot login simultaneously multiple device at a time.
View 21 Replies
View Related
Feb 2, 2012
We have an ACS 4.2 installation and we have users configured on the user setup, they authenicate using the windows database (AD). We ran failure tests and simulated AD failure but disabling the firewall rule. So the ACS server is up, AD is down. Tested user login to a switch and get the following error. External DB user invalid. It looks like as the ACS does not get a response from AD it rejects the user login.
What we want it to do is in the event of AD failure is to be able to login to the switch with the username configured on the switch. (as if ACS server does not respond)
Date Time Message-Type User-Name Group-Name Caller-ID Network Access Profile Name Authen-Failure-Code Author-Failure-Code Author-Data NAS-Port NAS-IP-Address Filter Information PEAP/EAP-FAST-Clear-Name EAP Type EAP Type Name Reason Access Device Network Device Group 02/03/201214:09:13Authen failedtest.testNetwork192.168.1.1(Default)External DB user invalid or bad password....tty310.0.0.1..........SWITCH30Office
View 3 Replies
View Related
Feb 27, 2012
Is it possible to track failed login attempts to ACS instances (both on CLI and web GUI) by snmp? unfortunately i haven't found such option in Monitoring and Reports > Alarms > Thresholds >
View 2 Replies
View Related
Nov 1, 2011
I have an ACS 5,2.0.26-8 running on VM intergrated with RSA. Users are able to login using their RSA passcode for network management utilizing TACACS. The problem seam to be related with RSA token caching. Once a user login sucessful on device A using current token he can not login with the same token on another device. User must wait for a new token and then he can login again. Before moving to ACS 5.2 we were using ACS 4.2 (intergrated with the same RSA) and back then ACS 4.2 cache passcode so user where able to login on devices using the same passcode. When the token change user have to use the new one. providing the same functionality like the "Token Card Settings" Durantion option under group properties, to cache token for a specific period. The global option for caching under RSA definition on 5.2 does not solve the problem.
View 4 Replies
View Related
Nov 4, 2012
I've configured three specific AD groups, Admin, Storage, and HelpDesk, with their own commands sets.
This seems to be working fine, but everyone can log into everything, but they can't do anything except exit.
My goal is to not allow anyone to login that is not part of the three AD groups I have specified with the respective command sets.
All the logins hit the Admin account, even though the id in AD is not in the that AD group. I have something screwed up.
View 6 Replies
View Related
Apr 22, 2013
How to see the ipsec vpn client users login history, they are authenticating to the local AAA, not to active directory. I am able to see current login session. by going to monitoring vpn statistics sessions this shows me current sessions but I would like to see for example logins for vpn client for the last month.
View 11 Replies
View Related
Jan 14, 2010
I've set up a ACS 5.1 Server an want to use it with our LDAP System. Therefor, I'm trying to login to a Cisco 1841 by using my LDAP Account, but it dosent work. The ACS seems not to know that it should use LDAP, because I get,"22056 Subject not found in applicable identity stores"LDAP is configured as Identitiy Store, the bind test works successfully and I created a sequence, where LDAP is at first position. What goes wron?? (TATACS for loal ACS Users works)
View 3 Replies
View Related