Is there a way to configure a ASA 5500 firewall so that when i access the firewall via SSH, my user is in privileged exec mode immediately after i have entered the log in credentials? So no need to enter "enable" anymore. I know how to do that with a router but couldn't figure it out for the ASA.
View 2 RepliesI am currently setting up a 2800 Series router, and prefer a username/password type authentication rather than a single enable password. To do this, I did:
Router(config)# username <myuser> privilege 15 secret 0 <mypassword>
Router(config)# username2 <myuser> privilege 15 secret 0 <mypassword>
Router(config)# aaa new-model
Router(config)# aaa authentication login default local
This basically does what I want - when I connect to the router through console, it immediately asks me for a username and password. The thing is - as soon as I provide the right credentials, it takes me to USER EXEC mode (the default command mode). Is it possible to change that so that after entering the credentials, I go right into privileged exec mode?
Bonus question: As it is now, I just have no enable password, so when I login with my credentials, I issue "enable" to enter privileged exec mode without it prompting for an additional password. Is it safe to do it this way - having no enable password but requiring a username and password for login?
I recently configured a Cisco AP 1242, software version 12.4, via the web interface using the default Cisco credentials. At that time I setup an administrator account with read/write access and changed the Cisco to a read only access. Now went I attempt to login to the web interface it won't accept the administrator password. It will except the administrator password in a telnet session however. So via the telnet session I setup another user with privileged exec level access and that wont work on the web interface either. The Login box keeps coming back requesting a password. Strangely enough, I can login to the web Interface using admin username, with the Cisco password; but I can't do anything, and I also can't view everything. I've tried the following:
I've turned on SSH and created a certificate in the AP, but the login box continues to pop on the https://url.I've attempted to setup a user with a non-encrypted password, but have been unsuccessful.I've tried a different browser - login box continues to pop.I've made sure the web interface is activated in the API've tried a differnet computerI've tried disabling password-encryption service. Reset the enable password , I've successfully setup other 1240 APs but must have done something wrong on this one.
Cisco cannot login? Currently i cannot login to the two of my cisco 3560 with the password that i usually used to login. and it is strength to me that its Configuration register is 0xF.
[BEGIN] 10/4/2011 10:22:57 AMshoTC-NGN-C3560-1>show verTC-NGN-C3560-1>show version Cisco IOS Software, C3560 Software (C3560-IPSERVICES-M), Version 12.2(35)SE5, RELEASE SOFTWARE (fc1)Copyright (c) 1986-2007 by Cisco Systems, Inc.Compiled Thu 19-Jul-07 18:15 by nachenImage text-base: 0x00003000, data-base: 0x01300000
ROM: Bootstrap program is C3560 boot loaderBOOTLDR: C3560 Boot Loader (C3560-HBOOT-M) Version 12.2(25r)SEC, RELEASE SOFTWARE (fc4)
TC-NGN-C3560-1 uptime is 50 weeks, 6 days, 9 hours, 34 minutesSystem returned to ROM by power-onSystem image file is "flash:c3560-ipservices-mz.122-35.SE5/c3560-ipservices-mz.122-35.SE5.bin"
[code]....
I have a customer with a 861 ISR.I want to block all the privilege 0 users from access the enable command
If i telnet into the device, as a priv=0, enable does not work
If i telnet into the device, as a priv=15, enable does work
If i telnet into the device, as a priv=0, enable does not work
If i telnet into the device, as a priv=15, enable does not work
I have issued the command:privilege exec level 15 enable Should block everyone except 15's from accessing the enable command SSH and TELNET are on the same vty:
line con 0
login authentication local_authen
no modem enable
line aux 0
line vty 0 3
[code]....
Basically TELNET is following the rules ( priv=0 not allowed to access enable ) but SSH is not following the rules ( both priv=15 and priv=0 cannot access the command ) is there a way from blocking somes users from login in completely?
I'm trying to configure ASA 5550 t8.4 so, that ssh and https access users would authenticate themselves vs Radius (or LDAP) server and they would be directly logged in with privilege mode 15.
I have Windows 2008 NTP acting as RADIUS server. And the network policy is: Service-Type - Login, Vendor-Specific - shell:priv-lvl=15 and allow full network access. All my AP's and switches with IOS are able to use that policy and i am able to get directly to exec mode (privilege lvl 15)
But on ASA, the user has to "enable" itself.
ASA conf:
#aaa-server <group name> protocol radius#aaa-server <group name> (inside) host <ip address> key 013B072C5A26070B2475411C350A18192218313A6A671F1A1B
#(config)aaa authentication ssh console <group name> LOCAL
#(config)aaa authentication http console <group name> LOCAL
How to get authorization working with LDAP (Active Directory)?
I am experiencing a problem that when I telnet a router ip.It prompts for username and password.After entering username and password the router enter into exec mode with > prompt.But when trying to enter in privilege exec mode by typing en or enable it gives error:
"Translating "en" %unknown command or computer name.or unable to find computer address".
This problem started on removing easy vpn configuration which include aaa new model configurations. The router is in production environment and have remote and console access.
I've got very basic problem but I cannot find the solution... I am sitting on the Cisco 4948E switch. And, I wanted to allow to guys who have not enable password to issue command sh running-config.I used the the following command to do that:SW4948E(config)#privilege exec level 1 show running-config.
View 3 Replies View Relatedhow to straight away enter priv EXEC mode when authenticated for asr1002?? Using XR12000, it can be done but asr1002 have to input enable passwd...my username for asr1002 have privilege 15 and i want to enter priv EXEC mode straight away after login without asking the enable passwd.
View 4 Replies View Related have a Cisco ASA that I am trying to configure in a unique way, I want it to perform a variety of tasks;
VPN SSL
VPN Tunnels
Firewall Inside to Outside via versa
But the difficult task, is creating a DMZ with devices that are assigned fully routed IP addresses from our ISP directly, these are H323 and SIP devices that cannot use NAT, and must have a fully routed IP address assigned to them.
Obviously the problem I have with the Firewall in its default routed mode, is that it wont allow me to overlap IP addresses on the outside interface with the DMZ interface.
Could the Firewall be configured for Transparent mode between Outside and DMZ, but Routed mode between Outside and Inside?
Eth0/0: 10.0.0./24 (inside)
Eth0/1: 190.0.0.0/24 (dmz)
Eth0/2: 190.0.0.0/24 (outside)
[Code]....
But could the new Cisco ASA with the latest firmware and model be ale to do this with 1 physical firewall?
Can you set the ASA 5500 series to learn the rule itself? I am talking about putting it into learning mode for first few weeks. I have done this with Zone Alarm software, but not sure this is available in Cisco 5500 series.
View 1 Replies View RelatedDo we have enable mod eon 2112 WLC ? Also if we need to access WAP from WLC how can we telnet or ssh?
View 5 Replies View Relatedhow to Config the ACS 4.2 server runs in TACACS + mode (users accounts configured the ACS) mode to authenticate enable mode password on the asa using the same AD account?
View 10 Replies View RelatedHow to enable security mode on DLINK wireless router DIR-615, after having it installed in "unsercured mode"?
View 1 Replies View RelatedHow do I enable the Security Mode on a Dling 615 wireless router?
View 1 Replies View RelatedI have a TWC wideband modem and service. I know that they will enable bridge mode if I ask them. My questions are. After they enable it whats my setup? Do I just run a cable from their modem into a new router that I then set up on my own? Is it that simple?
View 2 Replies View RelatedI am trying to get users in the external identity store (AD) to be dropped directly into enable mode after being authenticated, since I don't know of a way to set an enable password for users in an external identity store. I think it has something to do with shell attributes but I'm not realy sure.
So here's what I tried.Linking identity group to external group and provide full command priviliges - enable still didn't work Creating duplicate users in the internal identity store and setting the password type field to AD1 - That gives me the ability to get to the enable password prompt hit enter on the blank promt then prompts for Old and new passwords but fails everytime with an Error in Authentication.
How i can enable promiscuous mode on my Atheros AR9285 Wireless Network Adapter? I'm using windows 7 starter.driver version of my Atheros AR9285 Wireless Network Adapter:9.2.0.427.
View 4 Replies View RelatedOn my 2650 Router it just has only Telnet password.It has no enable mode password set.After reboot it is goes to prompt mode BB.I am unable to go to enable mode .how can i go back to enable mode on this router?
View 13 Replies View RelatedI had configured one access point CAP3602E in flex connect mode through a WLC 5508 after deploying the access point in flex control mode the local mac-filering is not working. before it was working when ap was in local mode. any body have to know is the mac-filtering working in flex-control mode ?
View 2 Replies View RelatedI configured the below config in Routers it is working good , but when i do the same in SWITCH-2960 , i am getting a problem not able to login to enable mode ... i am getting the basic login only ....
Error msg : % Error in Authentication.
Need to be configured at TAFE Network Devices: Code...
how do I setup an enable password for an ASA 5510? At the moment its setup to authenticate using RADIUS (which I'd like to keep doing) but I need to setup an enable mode password.
View 3 Replies View RelatedMy engineer onsite can't get into enable mode on his 2911 router. I've seen this before but I can't find out how I fixed it.
He gets an error saying : no password set
Here is the config:
Router#sh run
Building configuration...
Current configuration : 1784 bytes
!
[Code]....
So I have a Windows 2008 R2 SP1 Enterprise Server and a gigabit LAN network card onboard. But it refuses to run at gigabit speed and if forced to it, it just says that network cable is unplugged and doesn't work.
I tried switching to a newer and better motherboard (still with gigabit LAN)I have updated drivers.I have checked cables (which are all cat 6 cables and work just fine with other computers in gigabit LAN mode)I've checked and switched ports on the switch and the switch itself...no change. They work just fine with other non-W2008 machines, they get gigabit LAN
I am completely stomped as to what I can do to fix this. It runs just fine in 100 Mbit mode, but can't in any way get it in gigabit mode.I am completely stomped as to why it refuses...is this a limitation of Windows 2008 or something or is there a fix to this?
I have a dead DAP-1160 (RTL8186). I would try the JTAG recovery, so I compiled
-) includes-0.4.2
-) readline-5.2
-) jtag-0.6-cvs-20051228
under ubuntu 10.10.I have the cable DLC5 Xilinx.The problem is: I do not know how to enable the JTAG mode on the DAP-1160.I understand that I must set a pin on the 147 on the RTL8186. but I have no idea where is on the DAP-160 PCB.
My current production network is setup using VTP in Client mode, and I am looking to enable VTP Transparent so I can enable the extended VLANs. My main question would be, would enabling VTP Transparent on my 6509 affect all of the access switches it is connected to? And if so, would changing all of the access switches to VTP Transparent allow them to regain connectivity quickly with little downtime? Or is there another way that I should be handling this situation to enable the extended VLANs?
View 2 Replies View Related(5508 WLC, 1142N APs).I understand if I enable the AP mode to Rogue Detector from the details page of the AP, the AP stops accepting requests and is now looking for rogue items on the wired network. Is this the same when I enable Rogue Location Discovery Protocol? Will I lose the wireless functionality of all of my APs on the controller?
Next question, when I look at the Rogue Summary on the Monitoring page I see three Adhoc Rogue devices. When I select the Detail link only one shows. I remember the other two were HP mutifuction devices with WIFI enabled but I cannot retrieve that information anymore.
I successfully authenticate through ACS to my Identity Store, but only get dropped into a non-enable prompt: ciscoasa> How can I get an Authenticated user directly into enable mode?
View 3 Replies View RelatedI have 2691 router with following config
line console 0
login local
password xty
When i remove the login local from the line console i connect to console port and press enter it shows router prompt 2691Router> but i am unable to go to enable mode.If i telnet to router then i put username and pw then it goes straight to enable mode.
vty config is
line vty 0 4
exec-timeout 600 0
logging synchronous
login local
length 500
transport input telnet ssh
escape-character 3
Any reasons why i can not go to enable mode by console?
I got an ASA 5510 system currently in single context mode, with CSC SSM installed. Single ISP uplink to internet, no VPN. And now customer would like add another ISP uplink, without invest another box for HA.What come across my mind is make the current box into multi context. There's some area i need to concern and also need yours perspective on it.
Question 1: For making the firewall into multi context, am i need to do it from scratch, issue mode multiple command. Then rebuilt the current production config into one of the context, then another context meant for the new IPS uplink, and one admin context?
Question 2: For CSC -SSM licensing requirement, model ASA 5510 with security plus license is able to support 2 context. So if i split my firewall like what i mention in question, what exactly number of context do i own (admin, context A, context B)?
Question 3: For CSC-SSM module in multi context mode, so the management port of CSC SSM must attach at admin context?
Question 4: After configured all the policy and traffic to scan, how exactly i should do in order apply this policy to the interface? Should i only enable at admin context, then firewall service-policy rules, and apply it global, OR should i also do the same action on context A and Context B?
Can any ASA 5500 in particular the ASA5510 firewall support jumbo frames (i.e. greater than the default standard 1500 Bytes frames)?. I plan to use the ASAs to setup a point-to-point IPSec tunnel and need an Application frame of 4Kbytes intact and not segment it.I have done little checking on the Cisco Website and see it mention of Jumbo frames on the 5580 on 10Gig interface but didn't see mention 5510. 5580s are way over-kill and expensive for what I need is to run a mission critical one IPSec point-to-point with maximum of no more than 100Kbps so 5510 is perfect for me but not sure if it can carry the jumbo frame?
On the routers and switches it's the MTU settings and they are configurable per interface and I am OK and the circuit is T1 which the Telcos said it's OK since it's physical layer so the only unkown is the firewall.
I purchased the license P/N: ASA-CSC20-250U-1Y with Description: ASA 5500 CSC-SSM-20 250-User License Only Renewal (1-year)
But I had a mistake because I need support to 500 users. Now, to solve my mistake I want to know Do I can purchase another ASA-CSC20-250U-1Y to provide the 500 users suppor?
I mean, ¿are two (2) ASA-CSC20-250U-1Y equivalent to the 500 user license listed below?P/N, ASA-CSC20-500U-1Y with Description: ASA 5500 CSC-SSM-20 500-User License Only Renewal (1-year)
I have a pair of ASA 5520 firewalls running in active/standby mode on 8.3.2.34 code. My configuration performs authentication/authorization into ACS 5.1, however command authorization is failing when I try to execute a command on the standby from the active unit...
failover exec standby dir disk0:/
Fallback authorization. Username 'adminuser' not in LOCAL database Command authorization failed
I don't even see the authentication attempt going into ACS.