I have a dead DAP-1160 (RTL8186). I would try the JTAG recovery, so I compiled
-) includes-0.4.2
-) readline-5.2
-) jtag-0.6-cvs-20051228
under ubuntu 10.10.I have the cable DLC5 Xilinx.The problem is: I do not know how to enable the JTAG mode on the DAP-1160.I understand that I must set a pin on the 147 on the RTL8186. but I have no idea where is on the DAP-160 PCB.
I installed my 1522 today with a Direct TV receiver and made a connection using AP mode.
How do I know what band is being used and how to switch between the bads.
I m setup for my brother's next house. He wants to use to share with my internet access. I do have 2wire modem provider that has wireless capability in my house. So he have DAP-1522 [bridge mode] and adjust in Wireless Setting, to use SSID manual, (Bell9**) WPA. It s successful, and works well. Problem is cannot use wired to computers, blu-ray, Xbox 360 in same time. it will disconnect frequently because in bridge mode doesn't have DHCP reserved?
My bro bought other one is DIR-655. DAP-1522 keep in [bridge mode] to link to DIR-655 (Static IP), and setup DHCP Reserved. He feel relief that works very well and have no problem with any computers and devices doesn't disconnect anymore. my question is why DAP-1522 doesn't have DHCP reserved when bridge mode that connected to any providers modem?
I have a DSL router Pirelli PDF A1000G.I have a Linksys e3000 and I have a dap-1522.When I bought a dap-1522 I thought it could do access point in fact i saw many videos in dlinktv before choosing an access point from DIY with mike etc to youtube there are 2 videos one showing bridged mode and another ap mode!Now what happens is this I have upgraded from firmware 1.11 that came as default to 1.21 i connect it wired to my linksys e3000 when it is connected with the ethernet cable wired I can connect to the internet and navigate and open sites and my ps3 can connect to it but my range is not very good only 40%!
Now I bring it downstairs remove the ethernet cable and connect it to the power and then you can connect to it but since it isn't connected to my router which is upstairs i can't access websites neither can I play on my ps3!I don't know does only ap mode works when it is connected to the router wired because what happens is if you don't put ethernet cables in the back of the dap-1522 and just connect it to power then here doewnstairs you can connect to the dap-1522 my signal is like 87% but while I'm connected with my laptop I can't access websites and in the ps3 I can't connect!
and choose access points there are (4) listed: dap-1522, dap-1160, dap-1353 and dap-2553, I thought of buying dap-1522 because it could support abgn while 1160 only supports g and 1353 only supports n to repeat to signal here downstairs and be a good access point!
I am running a DAP-1522 (v1.21) in Bridge mode with a DIR-615 (1.00VG). I have configured the DAP-1522 to access the WiFi network and can see it connects correctly. I have a PC connected to the DAP-1522. Most of the time I can ping the DAP-1522 from the PC but cannot ping the DIR-615. Occasionally when I reboot everything again I can ping the DIR-615 and get full internet access but this usually only lasts a minute or so then it drops. After that I can only ping the DAP-1522. The DAP-1522 always says the Status is "connected" though.
The IP addresses are as follows:
DIR-615: 192.168.0.1
DAP-1522: 192.168.0.50 (static)
PC: 192.168.0.55 (static)
I've got the DAP-1522 connected in AP mode. Multiple N speed laptops but they're limiting out to G speeds (54 mbps). Firmware 1.31. Current config is
Wireless Mode : Access Point
802.11 Band : 2.4GHz
802.11 Mode : n and g
[Code].....
Connecting with brand new windows 7 laptops. N Capable. Some G laptops on the network as well.
I have just upgraded my network to the 802.11n standard, or at least am trying to do that. Im using a DIR-615 as Access Point and a DAP-1522 as bridge to cover the entire area.After having some trouble figuring out how to set up and connect the devices, i figure out that it might some other problem than my setup of the devices (The symptom was that the connection was ok, but then it seemed to be dropped, even though the DAP-1522 still displayed connected in the status page).
After reading what I could find about the DIR-615 and DAP-1522 in this forum and on the internet, I found a suggestion about changing the Wireless Mode from 802.11b/g/n to 802.11b/g, and after doing that everything works fine, its just not an upgrade anymore.I have fixed the channel to 10, just to check that it wasnt noise from other equipment. The symptoms are very reproducable, trying to connect wiin n-mode and bridge only works for 30-60 secs. Switching back to b/G mode and all is fine.
I turned it on for bridging and it did not auto setup wireless so i need to turn off WPS but my wireless option page is now blank. I rebooted, reset the DAP but still no manual config option. I found I could configure it if I switched it to AP mode but still cannot setup from bridge mode. According to manual a reset does not turn off WPS so what is the answer?
View 1 Replies View RelatedIf you are using DAP-1522 A1 and set to 5GHz 802.11 n bridge mode but disconnect randomly. Don't bother to do any troubleshooting because DAP-1522 A1 only support 802.11 draft n and incompatible with 802.11 n. If unit still under warranty then call D-Link and request unit replacement and ask for hardware reversion B1.
A1 - Ralink RT2880+RT2850 chips
[URL]
B1 - Ralink RT3662 chip
[URL]
I'm running the 1522 as a bridge with v1.21 firmware. I have 2 devices wired to it. I have Wireless MAC cloning disabled (not checked). If I scan my network using a tool such as ipscanner (http:url.....) the devices attached to the bridge are being listed with the 1522's MAC address - not their own.
The connected devices should be showing up with their own MAC addresses. The 1522's address should only be displayed IF MAC cloning is enabled and IF the cloning mode is set to Auto - is my understanding of this feature incorrect or is my 1522 not performing as spec'd?
I currently have a DAP1522 in Bridge mode with a DIR655. I am only using the 2.4GHz G mode on my 655. In a few days I will be replacing the 655 with an 825. When I log into the 1522 I don't see any settings for Mode, Frequency or Width (while in Bridge mode). The page for wireless setup is blank except for the "Save Settings" button. When I look at the 655, it appears that the 1522 is connected (bridged) at 2.4 GHz G like I would expect. So, when I install the 825 how do I make it connect at 5GHz N or will that be automatic if my SSID on the N mode of the 825 matches SSID on the 1522?
View 1 Replies View RelatedIf I turn off the wireless on my DAP-1522 in bridge mode, will it basically become a Gig Switch?? I've changed my network around abit and don't need it in bridge mode at this point but would love to use it as a plain switch. Would this do the trick??
View 3 Replies View RelatedI have a DAP-1522 in my den that I am connecting as a bridge to a Netgear WNDR3800 that in turn is connected to a cable modem in my living room. I have multiple PC's connected to the DAP-1522 via the Ethernet Ports. All the Ethernet connected PC's are getting IP addresses from my Netgear WNDR3800 via DHCP and can access the Internet fine. The weird thing is the PC's connected to the DAP-1522 through the Ethernet ports can't see each other - they are isolated from each other. I can see the DAP-1522 hard wired PC's from a laptop connected wirelessly through the Netgear WNDR3800 but the PC's wired to the DAP-1522 can't see each or communicate to each other via IP, though they can communicate to anything else on the Netgear WNDR3800 wireless network or Internet.Only the PC's connected to the DAP-1522 via the Ethernet ports are isolated from each other. Very strange. This is a problem because I have a NAS device I want to connect to the DAP-1522 that will be shared by the PCs in my den. I do software development and want access between the PC's and NAS device at Ethernet Gigabit speed. I am using default configurations for the DAP-1522. It appears that firmware for the bridging function if funky. I am on firmware version 1.41. The hardware release is A1.Not sure if it is an issue with the DAP-1522 or the Netgear WNDR3800.
View 5 Replies View RelatedI have a brand new DAP-1522 A1 connected to an 802.11n wireless LAN in bridge mode. Running in the 2.4GHz band with WPK-2 and AES security/encryption.Everything runs fine 99% of the time, but once a day or so the wireless LAN connection on the DAP-1522 drops and then takes about two minutes to re-connect. It re-connects and then everything is fine for a day or so until the next dropped wireless connection episode on the DAP-1522. I know my 802.11n wireless network is 100% fine as during the dropped connection to the DAP-1522 I can connect directly to the 802.11n wireless network (running from my gateway/router) using my other computer, no issues.I've seen some posts on this forum that the A1 version of the DAP-1522 hardware is not 100% compatible with the 802.11n network standard and there will be intermittent wireless drops. If this is true, it's just insane. All I can say is I can't believe DLink would allow a product to be sold that won't work properly on 802.11n networks.I check the logs each time I see the dropped wireless connection and all that shows is the following.1) Negotiating connection 2) 4-way handshake success [mac address]There's no message in the logs about why the wireless connection dropped, but I assume it has something to do with re-newing a key for the wireless network as the successful key renewal messages are the only other messages in the log. When the wireless network dropped I don't see the successful key renewal message at the time I should see it.I thought this DAP-1522 would take 15 minutes to configure in bridge mode and then I'd forget about it. Spend too much time on this already, so a bit disappointed with this DAP-1522 and DLink tech support....though when it's connected to the 802.11n wireless LAN it works fine.
View 14 Replies View RelatedRegion : Argentina
Model : TL-WR1043ND
Hardware Version : v1
my router is dead after my try of dd-wrt. it just flush 4 led and not respond. can i restore it connected rs232 or jtag? of cause know that it is not warranty at all, just need some diagram or something.
I'm about to purchase 2 Aironet APs, either 1140 or 1160 Series for a small Business. I know too little about the AP installation. How to let both APs works in Roaming Mode so that users can move freely within the site without having to drop and connect from one AP to the other.
View 4 Replies View RelatedHow to enable security mode on DLINK wireless router DIR-615, after having it installed in "unsercured mode"?
View 1 Replies View RelatedHow do I enable the Security Mode on a Dling 615 wireless router?
View 1 Replies View RelatedI have a TWC wideband modem and service. I know that they will enable bridge mode if I ask them. My questions are. After they enable it whats my setup? Do I just run a cable from their modem into a new router that I then set up on my own? Is it that simple?
View 2 Replies View RelatedHow i can enable promiscuous mode on my Atheros AR9285 Wireless Network Adapter? I'm using windows 7 starter.driver version of my Atheros AR9285 Wireless Network Adapter:9.2.0.427.
View 4 Replies View RelatedDo we have enable mod eon 2112 WLC ? Also if we need to access WAP from WLC how can we telnet or ssh?
View 5 Replies View Relatedhow to Config the ACS 4.2 server runs in TACACS + mode (users accounts configured the ACS) mode to authenticate enable mode password on the asa using the same AD account?
View 10 Replies View RelatedSo I have a Windows 2008 R2 SP1 Enterprise Server and a gigabit LAN network card onboard. But it refuses to run at gigabit speed and if forced to it, it just says that network cable is unplugged and doesn't work.
I tried switching to a newer and better motherboard (still with gigabit LAN)I have updated drivers.I have checked cables (which are all cat 6 cables and work just fine with other computers in gigabit LAN mode)I've checked and switched ports on the switch and the switch itself...no change. They work just fine with other non-W2008 machines, they get gigabit LAN
I am completely stomped as to what I can do to fix this. It runs just fine in 100 Mbit mode, but can't in any way get it in gigabit mode.I am completely stomped as to why it refuses...is this a limitation of Windows 2008 or something or is there a fix to this?
I am trying to get users in the external identity store (AD) to be dropped directly into enable mode after being authenticated, since I don't know of a way to set an enable password for users in an external identity store. I think it has something to do with shell attributes but I'm not realy sure.
So here's what I tried.Linking identity group to external group and provide full command priviliges - enable still didn't work Creating duplicate users in the internal identity store and setting the password type field to AD1 - That gives me the ability to get to the enable password prompt hit enter on the blank promt then prompts for Old and new passwords but fails everytime with an Error in Authentication.
On my 2650 Router it just has only Telnet password.It has no enable mode password set.After reboot it is goes to prompt mode BB.I am unable to go to enable mode .how can i go back to enable mode on this router?
View 13 Replies View RelatedI had configured one access point CAP3602E in flex connect mode through a WLC 5508 after deploying the access point in flex control mode the local mac-filering is not working. before it was working when ap was in local mode. any body have to know is the mac-filtering working in flex-control mode ?
View 2 Replies View RelatedI configured the below config in Routers it is working good , but when i do the same in SWITCH-2960 , i am getting a problem not able to login to enable mode ... i am getting the basic login only ....
Error msg : % Error in Authentication.
Need to be configured at TAFE Network Devices: Code...
how do I setup an enable password for an ASA 5510? At the moment its setup to authenticate using RADIUS (which I'd like to keep doing) but I need to setup an enable mode password.
View 3 Replies View RelatedMy engineer onsite can't get into enable mode on his 2911 router. I've seen this before but I can't find out how I fixed it.
He gets an error saying : no password set
Here is the config:
Router#sh run
Building configuration...
Current configuration : 1784 bytes
!
[Code]....
Is there a way to configure a ASA 5500 firewall so that when i access the firewall via SSH, my user is in privileged exec mode immediately after i have entered the log in credentials? So no need to enter "enable" anymore. I know how to do that with a router but couldn't figure it out for the ASA.
View 2 Replies View RelatedI successfully authenticate through ACS to my Identity Store, but only get dropped into a non-enable prompt: ciscoasa> How can I get an Authenticated user directly into enable mode?
View 3 Replies View RelatedMy D-Link DAP-1522 wireless bridge is connected through a single cat5 cable from the LAN port on my PC to the 1st LAN port on the D-link unit. At the moment, it is in bridge mode, with the blue power indicator on, the orange wireless connection light flashing, and the 1st LAN port connection periodically wavering indicating that it is communicating with my PC. When I attempt to configure the DAP-1522 via my internet browser, (IP 192.168.0.50) I get an error saying that the requested webpage does not exist.
View 6 Replies View RelatedMy current production network is setup using VTP in Client mode, and I am looking to enable VTP Transparent so I can enable the extended VLANs. My main question would be, would enabling VTP Transparent on my 6509 affect all of the access switches it is connected to? And if so, would changing all of the access switches to VTP Transparent allow them to regain connectivity quickly with little downtime? Or is there another way that I should be handling this situation to enable the extended VLANs?
View 2 Replies View Related
