how to Config the ACS 4.2 server runs in TACACS + mode (users accounts configured the ACS) mode to authenticate enable mode password on the asa using the same AD account?
View 10 RepliesI successfully authenticate through ACS to my Identity Store, but only get dropped into a non-enable prompt: ciscoasa> How can I get an Authenticated user directly into enable mode?
View 3 Replies View RelatedWe have ASA configured in multi context mode, with software 8.4(2) configured for AAA Configuration is admin context as follows:
aaa-server TAC protocol tacacs+
aaa-server TAC (management) host 10.162.2.201
key *****
aaa authentication enable console TAC LOCAL
aaa authentication http console TAC LOCAL
aaa authentication serial console TAC LOCAL
aaa authentication ssh console TAC LOCAL
Because of multiple context, after logging in we enter System context. Console port authentication is working fine except access to privileged mode while connecting over console port. After issuing "enable" command ASA accepts only configured enable secret in system context and changes user ID to enable_15, so we are unable to do user-level command authorization and accounting.It seems that ASA in system context is not aware of any AAA configuration, and there isn't any command to configure AAA in system context.Is there any way to configure enable authentication over AAA in system context?
It´s possible to enable unconditional machine authentication in ACS 5.3.
View 1 Replies View RelatedI am trying to get users in the external identity store (AD) to be dropped directly into enable mode after being authenticated, since I don't know of a way to set an enable password for users in an external identity store. I think it has something to do with shell attributes but I'm not realy sure.
So here's what I tried.Linking identity group to external group and provide full command priviliges - enable still didn't work Creating duplicate users in the internal identity store and setting the password type field to AD1 - That gives me the ability to get to the enable password prompt hit enter on the blank promt then prompts for Old and new passwords but fails everytime with an Error in Authentication.
I configured the below config in Routers it is working good , but when i do the same in SWITCH-2960 , i am getting a problem not able to login to enable mode ... i am getting the basic login only ....
Error msg : % Error in Authentication.
Need to be configured at TAFE Network Devices: Code...
how do I setup an enable password for an ASA 5510? At the moment its setup to authenticate using RADIUS (which I'd like to keep doing) but I need to setup an enable mode password.
View 3 Replies View RelatedI'm trying to configure ASA 5550 t8.4 so, that ssh and https access users would authenticate themselves vs Radius (or LDAP) server and they would be directly logged in with privilege mode 15.
I have Windows 2008 NTP acting as RADIUS server. And the network policy is: Service-Type - Login, Vendor-Specific - shell:priv-lvl=15 and allow full network access. All my AP's and switches with IOS are able to use that policy and i am able to get directly to exec mode (privilege lvl 15)
But on ASA, the user has to "enable" itself.
ASA conf:
#aaa-server <group name> protocol radius#aaa-server <group name> (inside) host <ip address> key 013B072C5A26070B2475411C350A18192218313A6A671F1A1B
#(config)aaa authentication ssh console <group name> LOCAL
#(config)aaa authentication http console <group name> LOCAL
How to get authorization working with LDAP (Active Directory)?
I have a setup with a were I configured monitor mode on a switch with ISE as RADIUS server. This is for testing before a bigger deployment at a customer site.Im using ISE 1.1.3, C2960 and IOS 15.0(2) and a laptop with Windows 7 Enterprise SP1. The correct configuration with EAP-TLS and machin cert is working like it should but it is when I remove this and make the laptop fail that I get wierd results with monitor mode. I cant get DNS to work in dot1x monitor mode if the client fail authentication.
When the client fail dot1x and MAB it gets a IP with DHCP. I can ping but DNS/browsing is not working. If I put the AuthC back and the client authenticates DNS is working, or if I turn of dot1x on the client then DNS work as it should. [code]
We would like to enable IS-IS HMAC-MD5 authentication on an production network for LSP authentication including LSP, CSNP and PSNP. The problem is that when we are applying the command "authentication mode md5" under the isis process there is authentications failure and the router loses all routes from routing table. Is there any way to enable authentication without the router losing the routing or to "delay" the authentication until all routers are configured.
key chain IS-IS
key 1
key-string xxx
[Code]....
I configured before ACS v4.2 to authenticate network devices using internal users at first, and if the user is not found use AD list users. But with v5.3 I have some problems doing this, on identity policies I use rule based result selection option, I configured 2 polices for Identity source, one for Internal Users and other policy for AD user, but it only works with the first policy, internal users or AD, but works only for the first policy identity. how to do that, if the user is not found on first policy, continue to the next policy.
View 7 Replies View RelatedI need a specify users to allow access to particular devices and give privilege only for show command or show run. Here is how I tried to configured.
1. Configured two seperate Shell Profile and Command set with privilege level 4-5 and allowing only show run command
2. create seperate service selection rule with adding the require NDG and protocol TACACS and maching service "RestrictAccess"
3. In the RestrictAccess Service I have following configured; Identity: internal users, Group Mapping to a particular group where the user exists, authorization: matching the above created identity group, NDG, shell profile, command sets
All the steps are attached in the .doc file. However when I tried with the particular user he is able to access everything and he is not hitting the correct access rule.
I've got a weird problem that I can't figure out. I've de-authorized the switch in the RADIUS server to force an ERROR status to test the backup entries in the AAA authentication method list. However, after I do that and try to log in (through ssh), it just prompts me for my username's password and not the enable password. Here's the debug output:
1d02h: RADIUS: Marking server xxx.xxx.xxx.xxx:1812,1813 dead
1d02h: RADIUS: Tried all servers.
1d02h: RADIUS: No valid server found. Trying any viable server
1d02h: RADIUS: Tried all servers.
1d02h: RADIUS: No response for id 10
[code]...
I've got a strange problem here. In the office, my OEAP 600 can join WLC if there is no MAC authentication. When i enable MAC authentication at WLC, AP will fail to register. However, I try it at home and it works with both MAC authentication enable or disable. I suspect it is because of firewall in my office, but there shouldn't have any different in discovery and joining procedure for AP with MAC authentication enable or disable.
View 18 Replies View RelatedDo we have enable mod eon 2112 WLC ? Also if we need to access WAP from WLC how can we telnet or ssh?
View 5 Replies View RelatedHow to enable security mode on DLINK wireless router DIR-615, after having it installed in "unsercured mode"?
View 1 Replies View RelatedHow do I enable the Security Mode on a Dling 615 wireless router?
View 1 Replies View RelatedI have a TWC wideband modem and service. I know that they will enable bridge mode if I ask them. My questions are. After they enable it whats my setup? Do I just run a cable from their modem into a new router that I then set up on my own? Is it that simple?
View 2 Replies View RelatedCan we enable ssh on 3500 /3600 APs along with use radius for login authentication? idea here is to that ssh will provide another method to access the AP for troubleshooting purposes.I know with autonomous mode APs this should not be an issue but not sure with lightweight APs.
View 2 Replies View RelatedHow i can enable promiscuous mode on my Atheros AR9285 Wireless Network Adapter? I'm using windows 7 starter.driver version of my Atheros AR9285 Wireless Network Adapter:9.2.0.427.
View 4 Replies View RelatedOn my 2650 Router it just has only Telnet password.It has no enable mode password set.After reboot it is goes to prompt mode BB.I am unable to go to enable mode .how can i go back to enable mode on this router?
View 13 Replies View RelatedI had configured one access point CAP3602E in flex connect mode through a WLC 5508 after deploying the access point in flex control mode the local mac-filering is not working. before it was working when ap was in local mode. any body have to know is the mac-filtering working in flex-control mode ?
View 2 Replies View RelatedMy engineer onsite can't get into enable mode on his 2911 router. I've seen this before but I can't find out how I fixed it.
He gets an error saying : no password set
Here is the config:
Router#sh run
Building configuration...
Current configuration : 1784 bytes
!
[Code]....
Is there a way to configure a ASA 5500 firewall so that when i access the firewall via SSH, my user is in privileged exec mode immediately after i have entered the log in credentials? So no need to enter "enable" anymore. I know how to do that with a router but couldn't figure it out for the ASA.
View 2 Replies View RelatedSo I have a Windows 2008 R2 SP1 Enterprise Server and a gigabit LAN network card onboard. But it refuses to run at gigabit speed and if forced to it, it just says that network cable is unplugged and doesn't work.
I tried switching to a newer and better motherboard (still with gigabit LAN)I have updated drivers.I have checked cables (which are all cat 6 cables and work just fine with other computers in gigabit LAN mode)I've checked and switched ports on the switch and the switch itself...no change. They work just fine with other non-W2008 machines, they get gigabit LAN
I am completely stomped as to what I can do to fix this. It runs just fine in 100 Mbit mode, but can't in any way get it in gigabit mode.I am completely stomped as to why it refuses...is this a limitation of Windows 2008 or something or is there a fix to this?
I have a dead DAP-1160 (RTL8186). I would try the JTAG recovery, so I compiled
-) includes-0.4.2
-) readline-5.2
-) jtag-0.6-cvs-20051228
under ubuntu 10.10.I have the cable DLC5 Xilinx.The problem is: I do not know how to enable the JTAG mode on the DAP-1160.I understand that I must set a pin on the 147 on the RTL8186. but I have no idea where is on the DAP-160 PCB.
My current production network is setup using VTP in Client mode, and I am looking to enable VTP Transparent so I can enable the extended VLANs. My main question would be, would enabling VTP Transparent on my 6509 affect all of the access switches it is connected to? And if so, would changing all of the access switches to VTP Transparent allow them to regain connectivity quickly with little downtime? Or is there another way that I should be handling this situation to enable the extended VLANs?
View 2 Replies View Related(5508 WLC, 1142N APs).I understand if I enable the AP mode to Rogue Detector from the details page of the AP, the AP stops accepting requests and is now looking for rogue items on the wired network. Is this the same when I enable Rogue Location Discovery Protocol? Will I lose the wireless functionality of all of my APs on the controller?
Next question, when I look at the Rogue Summary on the Monitoring page I see three Adhoc Rogue devices. When I select the Detail link only one shows. I remember the other two were HP mutifuction devices with WIFI enabled but I cannot retrieve that information anymore.
I have 2691 router with following config
line console 0
login local
password xty
When i remove the login local from the line console i connect to console port and press enter it shows router prompt 2691Router> but i am unable to go to enable mode.If i telnet to router then i put username and pw then it goes straight to enable mode.
vty config is
line vty 0 4
exec-timeout 600 0
logging synchronous
login local
length 500
transport input telnet ssh
escape-character 3
Any reasons why i can not go to enable mode by console?
I have created internal user on internal identiy store --> users with password & enable password , Similarly i have enabled max privilige level 15 under policy elements , authorisation & permission ,Device administration , shell profile .But i am unable to login into device using enable password , I am finding following error on my logg report
Failuire reason : 13029 Requested privilige level is too high .
How to configure authentication of enable password using acs 5.3. I have installed acs 5.3 and created user and gave relevant passwords. Following config is done on router
aaa new-model
aaa authentication login default group tacacs+ local
aaa authen enable default group tacacs+ enable
tacacs-server host x.x.x.x key xxxxx
Now when I telnet router, i can authenticate username/pass with acs5.3 but when i try to enter enable command and give password, it gives me error in authentication. What is the process of configuring enable passwords?
We are using ACS 5.3 with two servers in a distributed solution.All logs are collected on primary server so when this server fails all logs are lost.How can I enable log on secondary server also?
View 2 Replies View RelatedACS and i would like to know how to enable the "Configuration Audit" for someone login to my network devices using their ACS login and i can monitor what they did on it.
ACS Version : 5.2.0.26