I've got the DAP-1522 connected in AP mode. Multiple N speed laptops but they're limiting out to G speeds (54 mbps). Firmware 1.31. Current config is
Wireless Mode : Access Point
802.11 Band : 2.4GHz
802.11 Mode : n and g
[Code].....
Connecting with brand new windows 7 laptops. N Capable. Some G laptops on the network as well.
I m setup for my brother's next house. He wants to use to share with my internet access. I do have 2wire modem provider that has wireless capability in my house. So he have DAP-1522 [bridge mode] and adjust in Wireless Setting, to use SSID manual, (Bell9**) WPA. It s successful, and works well. Problem is cannot use wired to computers, blu-ray, Xbox 360 in same time. it will disconnect frequently because in bridge mode doesn't have DHCP reserved?
My bro bought other one is DIR-655. DAP-1522 keep in [bridge mode] to link to DIR-655 (Static IP), and setup DHCP Reserved. He feel relief that works very well and have no problem with any computers and devices doesn't disconnect anymore. my question is why DAP-1522 doesn't have DHCP reserved when bridge mode that connected to any providers modem?
I have a DSL router Pirelli PDF A1000G.I have a Linksys e3000 and I have a dap-1522.When I bought a dap-1522 I thought it could do access point in fact i saw many videos in dlinktv before choosing an access point from DIY with mike etc to youtube there are 2 videos one showing bridged mode and another ap mode!Now what happens is this I have upgraded from firmware 1.11 that came as default to 1.21 i connect it wired to my linksys e3000 when it is connected with the ethernet cable wired I can connect to the internet and navigate and open sites and my ps3 can connect to it but my range is not very good only 40%!
Now I bring it downstairs remove the ethernet cable and connect it to the power and then you can connect to it but since it isn't connected to my router which is upstairs i can't access websites neither can I play on my ps3!I don't know does only ap mode works when it is connected to the router wired because what happens is if you don't put ethernet cables in the back of the dap-1522 and just connect it to power then here doewnstairs you can connect to the dap-1522 my signal is like 87% but while I'm connected with my laptop I can't access websites and in the ps3 I can't connect!
and choose access points there are (4) listed: dap-1522, dap-1160, dap-1353 and dap-2553, I thought of buying dap-1522 because it could support abgn while 1160 only supports g and 1353 only supports n to repeat to signal here downstairs and be a good access point!
I am running a DAP-1522 (v1.21) in Bridge mode with a DIR-615 (1.00VG). I have configured the DAP-1522 to access the WiFi network and can see it connects correctly. I have a PC connected to the DAP-1522. Most of the time I can ping the DAP-1522 from the PC but cannot ping the DIR-615. Occasionally when I reboot everything again I can ping the DIR-615 and get full internet access but this usually only lasts a minute or so then it drops. After that I can only ping the DAP-1522. The DAP-1522 always says the Status is "connected" though.
The IP addresses are as follows:
DIR-615: 192.168.0.1
DAP-1522: 192.168.0.50 (static)
PC: 192.168.0.55 (static)
I have just upgraded my network to the 802.11n standard, or at least am trying to do that. Im using a DIR-615 as Access Point and a DAP-1522 as bridge to cover the entire area.After having some trouble figuring out how to set up and connect the devices, i figure out that it might some other problem than my setup of the devices (The symptom was that the connection was ok, but then it seemed to be dropped, even though the DAP-1522 still displayed connected in the status page).
After reading what I could find about the DIR-615 and DAP-1522 in this forum and on the internet, I found a suggestion about changing the Wireless Mode from 802.11b/g/n to 802.11b/g, and after doing that everything works fine, its just not an upgrade anymore.I have fixed the channel to 10, just to check that it wasnt noise from other equipment. The symptoms are very reproducable, trying to connect wiin n-mode and bridge only works for 30-60 secs. Switching back to b/G mode and all is fine.
I turned it on for bridging and it did not auto setup wireless so i need to turn off WPS but my wireless option page is now blank. I rebooted, reset the DAP but still no manual config option. I found I could configure it if I switched it to AP mode but still cannot setup from bridge mode. According to manual a reset does not turn off WPS so what is the answer?
View 1 Replies View RelatedIf you are using DAP-1522 A1 and set to 5GHz 802.11 n bridge mode but disconnect randomly. Don't bother to do any troubleshooting because DAP-1522 A1 only support 802.11 draft n and incompatible with 802.11 n. If unit still under warranty then call D-Link and request unit replacement and ask for hardware reversion B1.
A1 - Ralink RT2880+RT2850 chips
[URL]
B1 - Ralink RT3662 chip
[URL]
I'm running the 1522 as a bridge with v1.21 firmware. I have 2 devices wired to it. I have Wireless MAC cloning disabled (not checked). If I scan my network using a tool such as ipscanner (http:url.....) the devices attached to the bridge are being listed with the 1522's MAC address - not their own.
The connected devices should be showing up with their own MAC addresses. The 1522's address should only be displayed IF MAC cloning is enabled and IF the cloning mode is set to Auto - is my understanding of this feature incorrect or is my 1522 not performing as spec'd?
I currently have a DAP1522 in Bridge mode with a DIR655. I am only using the 2.4GHz G mode on my 655. In a few days I will be replacing the 655 with an 825. When I log into the 1522 I don't see any settings for Mode, Frequency or Width (while in Bridge mode). The page for wireless setup is blank except for the "Save Settings" button. When I look at the 655, it appears that the 1522 is connected (bridged) at 2.4 GHz G like I would expect. So, when I install the 825 how do I make it connect at 5GHz N or will that be automatic if my SSID on the N mode of the 825 matches SSID on the 1522?
View 1 Replies View RelatedIf I turn off the wireless on my DAP-1522 in bridge mode, will it basically become a Gig Switch?? I've changed my network around abit and don't need it in bridge mode at this point but would love to use it as a plain switch. Would this do the trick??
View 3 Replies View RelatedI have a dead DAP-1160 (RTL8186). I would try the JTAG recovery, so I compiled
-) includes-0.4.2
-) readline-5.2
-) jtag-0.6-cvs-20051228
under ubuntu 10.10.I have the cable DLC5 Xilinx.The problem is: I do not know how to enable the JTAG mode on the DAP-1160.I understand that I must set a pin on the 147 on the RTL8186. but I have no idea where is on the DAP-160 PCB.
My D-Link DAP-1522 wireless bridge is connected through a single cat5 cable from the LAN port on my PC to the 1st LAN port on the D-link unit. At the moment, it is in bridge mode, with the blue power indicator on, the orange wireless connection light flashing, and the 1st LAN port connection periodically wavering indicating that it is communicating with my PC. When I attempt to configure the DAP-1522 via my internet browser, (IP 192.168.0.50) I get an error saying that the requested webpage does not exist.
View 6 Replies View RelatedI have a DAP-1522 in my den that I am connecting as a bridge to a Netgear WNDR3800 that in turn is connected to a cable modem in my living room. I have multiple PC's connected to the DAP-1522 via the Ethernet Ports. All the Ethernet connected PC's are getting IP addresses from my Netgear WNDR3800 via DHCP and can access the Internet fine. The weird thing is the PC's connected to the DAP-1522 through the Ethernet ports can't see each other - they are isolated from each other. I can see the DAP-1522 hard wired PC's from a laptop connected wirelessly through the Netgear WNDR3800 but the PC's wired to the DAP-1522 can't see each or communicate to each other via IP, though they can communicate to anything else on the Netgear WNDR3800 wireless network or Internet.Only the PC's connected to the DAP-1522 via the Ethernet ports are isolated from each other. Very strange. This is a problem because I have a NAS device I want to connect to the DAP-1522 that will be shared by the PCs in my den. I do software development and want access between the PC's and NAS device at Ethernet Gigabit speed. I am using default configurations for the DAP-1522. It appears that firmware for the bridging function if funky. I am on firmware version 1.41. The hardware release is A1.Not sure if it is an issue with the DAP-1522 or the Netgear WNDR3800.
View 5 Replies View RelatedMy problem is two-fold:
1. the DAP-1522 will not connect to the 5GHz network of the DIR-815. Although, this doesn't surprise me as none of my 5GHz-capable devices see it, other than intermittently and at low signal. It is most likely an issue with the 815's 5GHz radio/network.
2. OTOH, the 1522 does appear to connect to the 815's 2.4GHz network just fine. However, there is no Internet access for any of the devices connected to the 1522's ports.
I know the 1522 can work correctly on 2.4GHz, as it previously did fine with my prior 2Wire router from AT&T. (I've just switched to Comcast, using the DIR-815 connected to their SMC modem.)
Also, I know the router and modem work fine (at least with 2.4GHz), as all of my wireless devices connect easily and with screaming bandwidth to the router and Internet.
I have a brand new DAP-1522 A1 connected to an 802.11n wireless LAN in bridge mode. Running in the 2.4GHz band with WPK-2 and AES security/encryption.Everything runs fine 99% of the time, but once a day or so the wireless LAN connection on the DAP-1522 drops and then takes about two minutes to re-connect. It re-connects and then everything is fine for a day or so until the next dropped wireless connection episode on the DAP-1522. I know my 802.11n wireless network is 100% fine as during the dropped connection to the DAP-1522 I can connect directly to the 802.11n wireless network (running from my gateway/router) using my other computer, no issues.I've seen some posts on this forum that the A1 version of the DAP-1522 hardware is not 100% compatible with the 802.11n network standard and there will be intermittent wireless drops. If this is true, it's just insane. All I can say is I can't believe DLink would allow a product to be sold that won't work properly on 802.11n networks.I check the logs each time I see the dropped wireless connection and all that shows is the following.1) Negotiating connection 2) 4-way handshake success [mac address]There's no message in the logs about why the wireless connection dropped, but I assume it has something to do with re-newing a key for the wireless network as the successful key renewal messages are the only other messages in the log. When the wireless network dropped I don't see the successful key renewal message at the time I should see it.I thought this DAP-1522 would take 15 minutes to configure in bridge mode and then I'd forget about it. Spend too much time on this already, so a bit disappointed with this DAP-1522 and DLink tech support....though when it's connected to the 802.11n wireless LAN it works fine.
View 14 Replies View RelatedAdding a second DAP-1522, They have 1 DAP-1522, they set that up useing the WAP(button on the side), This one is running in the frontroom of the house and the 2nd bridge will be running in the bedroom of the house.She has tried to click on the WAP button on both Dap-1522's and then the router to sync but thats not working, from what we can tell. I think I will need to manually config them now that a second one has been introduced.the frontroom Bridge is 192.168.0.50, but we cant find the ipaddreess for the second dap-1522 at this time. So question to all, if I can - Is there a way to identify all of the Dap-1522's on the network or anything that is connected on the network. as the DIR-655 is only showing 2 things connected?Right now I wish she would have listened too me and had her house wired for ethernet when the house was being built.
View 1 Replies View Relatedconnecting a Cisco 3945 Router to an Ethernet WAN Link. The service provider has provided a 100M Ethernet Single Mode Fiber handoff to the customer premises with SC Connector. The CPE configuration proposed for this setup is like this. [code]
Since the SFP has LC Connector, i suppose i need to have an SC-LC Cable for connecting the Ethernet link. Do i need anything else, apart from above?
basically my wireless speeds are around 0.5mb when i do a speedtest on windows, however on safe mode it will be 12mb. there's obviously some sort of conflict which i have struggled to identify.
here is what i tried
- fresh installs, although at the start the speeds are fine but once i install more drivers/programs it will do it
- installed different wireless drivers
- disabled certain processes/services
windows 7
pci express wireless adapter - TL-WR781ND
I'm facing a problem with the Cisco 1522 AP at the remote site every day that it takes about 2 hours to join the WLC, is there any way to minimize the time that the mesh 1522 AP takes to join the WLC?
View 2 Replies View RelatedI have a Dell Wireless 1500 draft N adapter that only connects at G speeds in mixed mode. I tried N only mode and my adapter will not connect. I have tried N mode Auto and 40hz wide and nogo. I have tried TKIP + AES and AES and nogo.
View 1 Replies View RelatedI recently installed a refurbished E2500 router. The reported speeds I got when hovering over the icon in the system tray ranged from 54 Mbps down to 1.0 Mbps. Also, it would drop, then reestablish, the connection several times per day.I contacted Tech Support via Live Chat, and got a woman who told me it was due to the fact that I'm using the router with an older system that has a wireless-G card (I'll be getting a new system soon).Of course, I thought that was ridiculous, so I called Linksys Tech Support and got a young man who had me reinstall the firmware upgrade (which I had already done when I installed the router). After that, it was good for about 24 hours, then the problems manifested again.I returned the router and ordered a replacement, also refrubished. Again, I upgraded the firmware upon installation. .
View 4 Replies View RelatedI recently had a networking guy set up a VPN for me, but for it to work properly he had to change all my IP addresses to 192.168.10.xx from 192.168.0.xx. My DAP-1522 (in bridge mode) continued to work but I am unable to log on to it, I think because it's address is 192.168.0.0. I have run into some other issues which makes me think I may need to upgrade the DAP-1522 firmware and/or assign it an address beginning with 192.168.10.xx, however I can't log on to the bridge. (Nor do I know how to change or possible reassign the DAP-1522's address through my router, a DIR-615).
View 5 Replies View RelatedI have a WIN XP desktop which I successfully connected to the 1522 AP - as evidence of the GUI to program it. I have the 1522 set to Bridge Mode via the switch on the unit. The 1522 has hardware version B1 and Firmware version 2.000. I joined my wireless network successfully as evidence of the Status page showing it's successfully connected and bridged to my network. I then disabled my USB wifi NIC in hopes of using my hardwired connection to the 1522 to get on the internet.
Wireless Radio : Enabled
Bridge State : Connected
MAC Address : fc:75:xxxxxx
802.11 Mode : Mixed 802.11a, 802.11g and 802.11n
Band Width : 40
Channel : 6
Network Name
(SSID) : cleveland
Wi-Fi Protected Setup : Enabled
Security : WPA2-PSK
I have dap-1522 version A Browser IE8 with lestest updates.
I downloaded the DAP1522_FW_1.31zip went I try to upload via the 1522 admin error not correct file.
I try three different way to download it, could the file be bad on dlinks web site?
I have just discovered after three weeks of testing that DAP-1522 wireless bridges are not compatible with all the new Pioneer AVR's that support internet radio and Iphone control. Anytime a DAP-1522 is powered on and on the same subnet mask as a Pioneer receiver it will cause the Pioneer to loose it's connection every 30 minutes. The receiver is then not able to connect unless it is powered off and on again. The DAP-1522 will cause this even if the Pioneer is hardwired to a router and nothing is plugged into the DAP-1522. This affects all new models of Pioneer receivers including the Elite line like I have.
I have tested this with 3 differnet Pioneer receivers and 2 DAP-1522's and always got the same results no matter what the settings were and with the 1522 in AP or bridge mode. Other Pioneer receiver owners experiencing constant disconnect problems on another forum have now also confirmed they have DAP-1522's.....and they are also pissed after spending countless hours troubleshooting.
I talked to Dlink support today and they will not admit to a problem so I can't wait to contact Pioneer tech support on Monday to let them know I have found the reason they are seeing returns on their new receivers (some cost as much as $7K) since many of the new owners like myself are exchanging them thinking they got a bad one. I'm sure Pioneer will test this immediately and force a Dlink fix or turn it over to the FCC.At this point I just wish I could get my money back since I have also already confirmed that a netgear bridge works just fine. Come to think of it, I know Dlink has a new refund policy, but I will check with my state district attorney to see if they can legally keep my money even if the product doesn't work. I don't see anything on the outside of the box with this policy so therfore I wasn't given fair warning of the policy before purchase and would not be expected to know it since it is not industry standard. Let the games begin.
I just purchased a DAP-1522. The sticker on the bottom says it's a version B1, with firmware 2.0.In the web interface, it says: "Firmware Version : 1.21 , Fri 26 Jun 2009"I downloaded the 2.01 firmware from the D-Link site and when I try to upload it, it says it's not an image file.
View 11 Replies View RelatedI have bought 1 Dlink Dwl 2100 Access Point about 1 week, it working with ( Default Gateaway 192.168.1.1) but I want connect with 2100Ap But I get Ip from my Livebox Orange.Can I get Ip From 2100Ap (Default Gateway 192.168.0.50), not by LiveBox Orange (Default Gateway 192.168.1.1).My brother live upstair (with LiveBox) I Live ground Floor and connect to Cable Utp cat5 form upstair to ground Floor. In my room I have a Switch connect to 2100Ap.
LiveBox Orange Default gateway is 192.168.1.1
Dlink dwL 2100Ap Default Gateway is 192.168.0.50
My os is windows Xp sp2
I have a DIR-655 router with a DAP-1522 connected in bridge mode. The firmware on the router is 1.21 and the firmware on the bridge is 1.21. I have my SSID set to broadcast on the DIR-655 with WPA-Personal encryption. When I initially setup the DAP-1522, I was able to access the setup page and connect to the DIR-655. On the status page of the DAP-1522, wireless radio is enabled and status is connected. I connected my XBOX 360, Sony BR player and DirecTV DVR to the wireless bridge and none of them can connect to the internet.
I can wirelessly access the bridge's IP, 192.168.0.50, from any computer connected to the DIR-655 but when I attempt to access the internet on any device connected to the DAP-1522, I do not get a connection. On the XBOX 360 I cannot connect my live account. On the Sony BR player, I get a message that new firmware was found, but when it attempts to connect to the internet to download it, the connection times out. Same occurs when attempting to access the internet on the DirecTV DVR receiver.
More that a year ago, with guidance from D-Link Customer Service, I performed setup on a system consisting of a DSL-2640B (with wireless disabled) and a DAP-1522 as an access point. I included the 1522 so as to have an N network, since the 2640 is G. The system works fine and I'm able to stream via the 1522 to an N 300 USB Adapter. Internet access is fine, and I'm able to access the 2640 with no problem.I want to add another 300 in a different location. To do that, I'll need to access the 1522 from my Windows 7 computer, since I've lost the passphrase that I'll need for the 300.Everything that I've read tells me to connect the 1522 directly to my computer via cable and to temporarily change the network adapter settinge to:
IP = 192.168.0.x various sources list values of 2 and 99 for x
Subnet mask = 255.255.255.0
Gateway = 192.168.0.50
Then to use a browser window to go to 192.168.0.50 Regardless of the settings that I use, the browser (IE9) always indicates that it can't connect with that address. accessing the 1522, or on any alternative way to obtain the passphrase.
My DIR 655 router quit working and so I called D link. She had me reset the ip to 192.168.5.x. So now my dap1522 is not connecting to the 655. I connected the dap1522 to my laptop via ether-net and typed in dink, and got nothing, then put in default ip for the 1522 and still nothing. I also tried ip scanner and it would not come up.
View 1 Replies View Relatedmy config : one DAP-1522 as an AP + one DAP-1522 as a switch, 6 meters between them, signal strength about 70. Any others wifi networks around my house. both with FW140b03.bin dated 01/14/2011.Most of the time, both work correctly. But time to time, the wifi link is ko. In AP status, the switch is mentionned connected (uptime = 3 hours ...). The red led is blinking on the switch. The administration web of the switch is not available and the link is ko. Unplug and plug power units doesn't fix the problem. I need to reset DAPs.From Dlink experts, i would like to get more description about issues :
- in switch mode, which are the events modifying the red led state ? what does blinking / off led mean ?
- in AP mode, what does "uptime ...STA ...." mean ? frames are periodically received from STA ?
Will the dap-1522 work with 3d video ie; from a 3d Blue Ray Player? I am upgrading system to an LED Samsung 3D TV and Samsung 3d Blue Ray Player. I know that HDMI 1.4 cables will work but am looking at the wireless option.
View 1 Replies View Relatedi got a Dir-655 router and Dell 1501 wireless -N mini PCI card (802.11 bgn compliant). Router was set to mix mode but my desktop Dell XP8300 can connect only till G mode.
1) I search on web and some said that i need to set my router to N mode only for my desktop to connect to N mode. IS THIS SOLUTION CORRECT??
2) Another issue was my sis got other old brand latop which can only connect to B mode, if i set to N mode only, she won't be able to connect it right?