D-Link DAP-1522 :: AP MODE Doesn't Work?
Jan 6, 2011
I have a DSL router Pirelli PDF A1000G.I have a Linksys e3000 and I have a dap-1522.When I bought a dap-1522 I thought it could do access point in fact i saw many videos in dlinktv before choosing an access point from DIY with mike etc to youtube there are 2 videos one showing bridged mode and another ap mode!Now what happens is this I have upgraded from firmware 1.11 that came as default to 1.21 i connect it wired to my linksys e3000 when it is connected with the ethernet cable wired I can connect to the internet and navigate and open sites and my ps3 can connect to it but my range is not very good only 40%!
Now I bring it downstairs remove the ethernet cable and connect it to the power and then you can connect to it but since it isn't connected to my router which is upstairs i can't access websites neither can I play on my ps3!I don't know does only ap mode works when it is connected to the router wired because what happens is if you don't put ethernet cables in the back of the dap-1522 and just connect it to power then here doewnstairs you can connect to the dap-1522 my signal is like 87% but while I'm connected with my laptop I can't access websites and in the ps3 I can't connect!
and choose access points there are (4) listed: dap-1522, dap-1160, dap-1353 and dap-2553, I thought of buying dap-1522 because it could support abgn while 1160 only supports g and 1353 only supports n to repeat to signal here downstairs and be a good access point!
View 3 Replies
ADVERTISEMENT
May 7, 2011
hardware version D3, FW 4.10 and 4.11 same problem.
i tried with 4 wlan adapters: two of them support 802.11b/g, they always work find no matter which settings. the other two support 802.11b/g/n, as default "n" is enabled, so does DIR-615, both wlan adapters can be connected to DIR-615, they get their LAN-IP, but they can access neither DIR-615(no respone to ping) nor internet. but if i disable "n" mode either in the adapter or in DIR-615, everythin works fine, of course only with 54mbit max.
so what can i do to use the n mode?
View 1 Replies
View Related
Apr 13, 2011
I m setup for my brother's next house. He wants to use to share with my internet access. I do have 2wire modem provider that has wireless capability in my house. So he have DAP-1522 [bridge mode] and adjust in Wireless Setting, to use SSID manual, (Bell9**) WPA. It s successful, and works well. Problem is cannot use wired to computers, blu-ray, Xbox 360 in same time. it will disconnect frequently because in bridge mode doesn't have DHCP reserved?
My bro bought other one is DIR-655. DAP-1522 keep in [bridge mode] to link to DIR-655 (Static IP), and setup DHCP Reserved. He feel relief that works very well and have no problem with any computers and devices doesn't disconnect anymore. my question is why DAP-1522 doesn't have DHCP reserved when bridge mode that connected to any providers modem?
View 1 Replies
View Related
Nov 23, 2010
I am running a DAP-1522 (v1.21) in Bridge mode with a DIR-615 (1.00VG). I have configured the DAP-1522 to access the WiFi network and can see it connects correctly. I have a PC connected to the DAP-1522. Most of the time I can ping the DAP-1522 from the PC but cannot ping the DIR-615. Occasionally when I reboot everything again I can ping the DIR-615 and get full internet access but this usually only lasts a minute or so then it drops. After that I can only ping the DAP-1522. The DAP-1522 always says the Status is "connected" though.
The IP addresses are as follows:
DIR-615: 192.168.0.1
DAP-1522: 192.168.0.50 (static)
PC: 192.168.0.55 (static)
View 9 Replies
View Related
May 18, 2011
I've got the DAP-1522 connected in AP mode. Multiple N speed laptops but they're limiting out to G speeds (54 mbps). Firmware 1.31. Current config is
Wireless Mode : Access Point
802.11 Band : 2.4GHz
802.11 Mode : n and g
[Code].....
Connecting with brand new windows 7 laptops. N Capable. Some G laptops on the network as well.
View 2 Replies
View Related
Sep 19, 2009
I have just upgraded my network to the 802.11n standard, or at least am trying to do that. Im using a DIR-615 as Access Point and a DAP-1522 as bridge to cover the entire area.After having some trouble figuring out how to set up and connect the devices, i figure out that it might some other problem than my setup of the devices (The symptom was that the connection was ok, but then it seemed to be dropped, even though the DAP-1522 still displayed connected in the status page).
After reading what I could find about the DIR-615 and DAP-1522 in this forum and on the internet, I found a suggestion about changing the Wireless Mode from 802.11b/g/n to 802.11b/g, and after doing that everything works fine, its just not an upgrade anymore.I have fixed the channel to 10, just to check that it wasnt noise from other equipment. The symptoms are very reproducable, trying to connect wiin n-mode and bridge only works for 30-60 secs. Switching back to b/G mode and all is fine.
View 14 Replies
View Related
Nov 22, 2011
I turned it on for bridging and it did not auto setup wireless so i need to turn off WPS but my wireless option page is now blank. I rebooted, reset the DAP but still no manual config option. I found I could configure it if I switched it to AP mode but still cannot setup from bridge mode. According to manual a reset does not turn off WPS so what is the answer?
View 1 Replies
View Related
Nov 28, 2012
If you are using DAP-1522 A1 and set to 5GHz 802.11 n bridge mode but disconnect randomly. Don't bother to do any troubleshooting because DAP-1522 A1 only support 802.11 draft n and incompatible with 802.11 n. If unit still under warranty then call D-Link and request unit replacement and ask for hardware reversion B1.
A1 - Ralink RT2880+RT2850 chips
[URL]
B1 - Ralink RT3662 chip
[URL]
View 6 Replies
View Related
May 16, 2011
I'm running the 1522 as a bridge with v1.21 firmware. I have 2 devices wired to it. I have Wireless MAC cloning disabled (not checked). If I scan my network using a tool such as ipscanner (http:url.....) the devices attached to the bridge are being listed with the 1522's MAC address - not their own.
The connected devices should be showing up with their own MAC addresses. The 1522's address should only be displayed IF MAC cloning is enabled and IF the cloning mode is set to Auto - is my understanding of this feature incorrect or is my 1522 not performing as spec'd?
View 7 Replies
View Related
Apr 25, 2012
I currently have a DAP1522 in Bridge mode with a DIR655. I am only using the 2.4GHz G mode on my 655. In a few days I will be replacing the 655 with an 825. When I log into the 1522 I don't see any settings for Mode, Frequency or Width (while in Bridge mode). The page for wireless setup is blank except for the "Save Settings" button. When I look at the 655, it appears that the 1522 is connected (bridged) at 2.4 GHz G like I would expect. So, when I install the 825 how do I make it connect at 5GHz N or will that be automatic if my SSID on the N mode of the 825 matches SSID on the 1522?
View 1 Replies
View Related
May 30, 2012
If I turn off the wireless on my DAP-1522 in bridge mode, will it basically become a Gig Switch?? I've changed my network around abit and don't need it in bridge mode at this point but would love to use it as a plain switch. Would this do the trick??
View 3 Replies
View Related
Jan 24, 2011
I have a dead DAP-1160 (RTL8186). I would try the JTAG recovery, so I compiled
-) includes-0.4.2
-) readline-5.2
-) jtag-0.6-cvs-20051228
under ubuntu 10.10.I have the cable DLC5 Xilinx.The problem is: I do not know how to enable the JTAG mode on the DAP-1160.I understand that I must set a pin on the 147 on the RTL8186. but I have no idea where is on the DAP-160 PCB.
View 1 Replies
View Related
Dec 28, 2010
DGL-4100
-> Wii
-> X360
-> PS3
-> DGS-2205 (gigabit switch in study)
*-> My PC
*-> Her PC
*-> DAP-1522
We're on the 192.168.1.x domain, and I've already hooked my PC up directly to the DAP-1522 and switched its IP address. So now, I can connect to it through the switch. I've renamed it, set it to WPA2 with a passphrase, and should be set to go. However, I can't get my laptop, IPod touch, or any devices to see it. Also, the DGL-4100 doesn't list it under the DHCP clients, but as I've got the DAP-1522 set to a static IP of 192.168.1.50.
View 1 Replies
View Related
Jun 13, 2012
I have a DAP-1522 in my den that I am connecting as a bridge to a Netgear WNDR3800 that in turn is connected to a cable modem in my living room. I have multiple PC's connected to the DAP-1522 via the Ethernet Ports. All the Ethernet connected PC's are getting IP addresses from my Netgear WNDR3800 via DHCP and can access the Internet fine. The weird thing is the PC's connected to the DAP-1522 through the Ethernet ports can't see each other - they are isolated from each other. I can see the DAP-1522 hard wired PC's from a laptop connected wirelessly through the Netgear WNDR3800 but the PC's wired to the DAP-1522 can't see each or communicate to each other via IP, though they can communicate to anything else on the Netgear WNDR3800 wireless network or Internet.Only the PC's connected to the DAP-1522 via the Ethernet ports are isolated from each other. Very strange. This is a problem because I have a NAS device I want to connect to the DAP-1522 that will be shared by the PCs in my den. I do software development and want access between the PC's and NAS device at Ethernet Gigabit speed. I am using default configurations for the DAP-1522. It appears that firmware for the bridging function if funky. I am on firmware version 1.41. The hardware release is A1.Not sure if it is an issue with the DAP-1522 or the Netgear WNDR3800.
View 5 Replies
View Related
Jan 28, 2010
I want to send a WoL (wake on lan) packet to power up a PC which is wired to DAP-1522. The DAP-1522 is connected to my DIR-655 router wirelessly. So far, I have no luck. Do you know if the DAP-1522 is capable of passing the WoL? Does it need a firmware upgrade before it can do so?
View 7 Replies
View Related
May 22, 2012
Jason9 i'm having the exact same problem as above, don't mean to hijack but I'm using talktalk isp, I have AVG 9.0 and have a static IP and forwarded the required port on the router.
View 19 Replies
View Related
Apr 21, 2013
I have a brand new DAP-1522 A1 connected to an 802.11n wireless LAN in bridge mode. Running in the 2.4GHz band with WPK-2 and AES security/encryption.Everything runs fine 99% of the time, but once a day or so the wireless LAN connection on the DAP-1522 drops and then takes about two minutes to re-connect. It re-connects and then everything is fine for a day or so until the next dropped wireless connection episode on the DAP-1522. I know my 802.11n wireless network is 100% fine as during the dropped connection to the DAP-1522 I can connect directly to the 802.11n wireless network (running from my gateway/router) using my other computer, no issues.I've seen some posts on this forum that the A1 version of the DAP-1522 hardware is not 100% compatible with the 802.11n network standard and there will be intermittent wireless drops. If this is true, it's just insane. All I can say is I can't believe DLink would allow a product to be sold that won't work properly on 802.11n networks.I check the logs each time I see the dropped wireless connection and all that shows is the following.1) Negotiating connection 2) 4-way handshake success [mac address]There's no message in the logs about why the wireless connection dropped, but I assume it has something to do with re-newing a key for the wireless network as the successful key renewal messages are the only other messages in the log. When the wireless network dropped I don't see the successful key renewal message at the time I should see it.I thought this DAP-1522 would take 15 minutes to configure in bridge mode and then I'd forget about it. Spend too much time on this already, so a bit disappointed with this DAP-1522 and DLink tech support....though when it's connected to the 802.11n wireless LAN it works fine.
View 14 Replies
View Related
Jun 4, 2011
So just recently purchased the DIR-825 and DAP-1522. At this point I just want to get the DAP-1522 to work as a wireless access point to my DIR-825. So my wireless laptop would connect wirelessly to the DAP-1522 and the 1522 would go wireless to the router. Pretty basic I guess. I was planning on using the WAP to strengthen the 5 GHz signal to the router but again, at this point, I would be happy to get the 2.4 GHz working.
I've been working on this since last night and got frustrated and went to bed. I woke up fresh and decided to try again and I'm not having making any headway.
DIR-825 is connected to my DSL modem and has no problem accessing the internet. I can connect to either 2.4 or 5.0 directly from my laptop with no problem at all and have access to the internet. Encryption is disabled. It worked with encryption but I turned it off to troubleshoot this AP problem.
It should be simple but I must be doing something wrong. BTW is there a way to scan for network devices from the router or the access point? I tried discovering each device with the wireless setup button on each device but they don't recognize each other so I'm configuring this manually.
So the DAP has access point enabled and 802.11 is running in mixed mode. I've tried different variations but nothing has worked. I've tried 20 mhz and 20-40 auto mhz channels but same problem. Wireless security is off for troubleshooting at the moment.
DHCP server is disabled and I've assigned the DAP an available ip from the router's dhcp range. I can connect to the DAP both wirelessly and hard wired. The problem is that it can't seem to connect to the router. So my laptop can connect to the router and ha internet access. And it can also connect to the DAP but does not have internet access. The ip is showing auto configuration 169.x.x.x when connected to the DAP so I'm not getting an ip. Is the router supposed to assign the ip to my laptop through the DAP? But again, if the DAP can't communicate with the router, then that would explain why I can't get an IP.
View 1 Replies
View Related
May 2, 2012
We are deploying a new office and exploring the options for WLAN deployment. We were pretty impressed with 3500 series APs and that it supports CleanAir.However, we have decided to go for standalone AP deployment model now. As 3500 does not work in standalone mode, so we are looking for APs that can work in standalone mode ( and later can be converted to lightweight if needed). We can go for 1140 in that case. However, it would be better for us to know the main differences between features supported by 3500 lightweight AP and 1140 standalone AP. CleanAir looks like the main one. Are there other important ones as well?
View 2 Replies
View Related
Mar 12, 2012
I have a WAP54G v3.1 running firmware version 3.05.01 and a WRT54G v3 running Tomato v1.28. The WAP54G is configured client mode and works perfectly. However, I was not able to get the two to communicate with WPA2 security - maybe, I just didn't try hard enough? Both devices are capable of doing WPA2 with AES but client mode doesn't seem to work with WPA2? I had to drop back to WPA-AES to make it work. Why is this?
View 4 Replies
View Related
Jan 10, 2012
I recently bought a Cisco E2500 for work, and after setting the router to Bridge Mode, I am unable to access the router web interface. I tried both the old IP address (192.168.1.1) and the IP address that I entered when I was configuring Bridge mode, but I couldn't get either to work. I have always tried resetting the switch to factory defaults and trying again to make sure I didn't type anything wrong, but to no avail. The wireless and everything works as it should, I just can't get back into the router to change any of my settings.
View 4 Replies
View Related
Aug 9, 2011
We have three brand new E4200 routers, all using the most current firmware (1.0.02). They are all in bridged mode, however when I attempt to enable the guest network on each of them, the config shows it as active, but it never shows up as visiible SSID. In previous posts, I've seen people saying that I need to do a complete hard reset of the router and re-enter all the configs again to get the guest network active. Is this true? I'd hate to think that I have to hard reset and reconfigure all three of these APs, just to get the guest network enabled.
View 2 Replies
View Related
Aug 10, 2011
The DIR-825 wireless simply doesn't work. When I called tech support, we cleared some settings and hard-powered the unit on/off and it finally turned on the wireless radio. A couple weeks later I pull out my laptop to use in the house via wireless and the wireless on the DIR-825 is OFFLINE AGAIN...fallen and it can't get UP.Is anyone having issues with keeping their wireless online? OK - powered it off for 5 minutes...now the wireless is working. I think changing configuration settings causes the thing to lock up.
View 1 Replies
View Related
Feb 3, 2013
Recently I bought a Windows 8 (64bits) computer, which is now part of my home network, but it has problems with Shareport. The other computers can be easily connected to a USB printer on my DIR-825 (HW B1) router, but the W8 computer refuses to completely install Shareport (both the CD version and the latest download v1.17). I also tried Shareport-Plus v4.11 (found on the DIR 835 page), which did install correctly, but was still unable to see the USB printer. What can be done? Can D-Link provide a new version of Shareport?
View 3 Replies
View Related
Dec 25, 2011
I can't get my brand new DCS-930L cam to connect to my network by using the WPA / WPA2 encryption. Works ok wired, with WEP or with no encryption enabled. Red led is on the front. I've tested sw version 1.02, 1.03 and the latest 1.04b03. Same result: WPA doesn't work. I have a Thomson TG789 Gateway/Router as provided by my ISP. All other units in the network works perfectly fine on WPA i.e. PC, Mac, printers, mobile phones etc etc.
View 1 Replies
View Related
Nov 21, 2012
i have a DIR-615 Rev C1, firmware 3.13.
After a reboot my password doesn't work anymore (wich is normal I guess) and all default passwords dont either. Such as ''Password'' or ''Admin''.
View 1 Replies
View Related
May 12, 2011
Edit I've found a work-around. It's on page 2: [URL]
I'm having this really weird issue with my DIR-655 revB. I have some port forwarding rules set up and externally they work fine. However, if I try connecting to my IP address using those same ports from a computer within my LAN, it won't connect.
Externally, I can ping my WAN address and connect through forwarded ports. No problems. Internally, pinging my WAN address apparently works (just now is the first time that's worked for me), however I can't access any of my computers using the WAN IP and port forwarded ports. I can access them by going directly to their hostnames or LAN IPs.
Things I've tried:
-Disabling/enabling firewalls on all computers involved
-Disabling/enabling QoS engine
-Disabling/enabling DNS relay
-Disabling/enabling Advanced DNS
-Adding custom nameservers from Google and Comodo
-Restarting computers
-Clearing DNS cache (I use a dynamic DNS name which works externally but not internally. This gets the correct IP internally and connecting directly to the IP doesn't work either.)
-Modifying the NAT Endpoint Filtering settings
I have an external DSL modem connected to the router using PPPoE if it matters.
The weird part is that it works externally but I've modified all of the values I can think of in the config with no luck. I upgraded to the DIR-655 from a DIR-615 which had all these settings in it and worked fine (until it started acting up which is why I replaced it).
View 14 Replies
View Related
Feb 17, 2013
I realized that when I connect dir825 on bridging mode to my current voip router provided by my ISP (dvg-n5402) ,shareport does not work as it seems to be using the default gateway to find the usb, which in this case default gateway goes to the gateway of my voip router. Is there any way that I can make shareport use the gateway of my dir825 instead?
View 5 Replies
View Related
Feb 26, 2012
Like others I see on this board, we've got middle- and high-school age kids whose access to FB and other sites needs to be controlled/scheduled.
I thought the DIR-655 was great, in that it has features that, on the face of it, would seem to be ideal for blocking domains and restricting access.
My problem: I've never been able to get this to work.
I've set up schedules and created lists of domains that I want to limit access to according to the schedules, but the only constraint I've ever gotten to stick is blocking access completely to the router.
*None* of the schedule-based or website-based access controls have ever worked; I'll put the block in place to my daughter's computer's MAC address so she shouldn't be able to get to youtube or facebook, save, bounce the router, but then I go by her room and she's still busily chatting away online to her FB friends.
Based on similar posts I've seen on this forum, this may not be a unique problem.
So in a nutshell, this is what I want to do:
1) Block certain computers (identifiable by MAC address)
2) from being able to get to particular named domains (and any of their sub-domains)
3) according to a schedule that I can create and modify.
My preference would be to do this in the router, but again, responses I've seen here suggest that may not be possible.
View 1 Replies
View Related
Jan 5, 2011
My DIR-655:
Hardware Version: A4
Product Page: DIR-655
The problem is that Website Filer doesn't work if on STEP 3: SELECT MACHINE of Access Control the machine was selected by MAC address. When the machine was selected by IP everything is fine.The problem is that IP addresses are assigned dynamically, so how to make sure that the policy would be applied to the same machine?
View 8 Replies
View Related
Dec 11, 2011
I just got my DIR 825. It had 2.02NA Firmware in it. It had a few options that I wanted to use but didn't work. So I thought I would update firmware. I follow the instruction from dlink to install firmware. So I loaded 2.03 and noticed internet connection not working. So then I loaded 2.05 part1 and part2. Still could get internet connection to work but the reason to upgrade the option I wanted worked. So then I loaded 2.06 and still same result. No internet connection. So then I loaded the original firmware back in and internet connection works. Why doesn't the internet work on the other firmware updates. I got the updates from dlink website. I would like to update firmware
View 9 Replies
View Related
Jan 12, 2012
I had the website filter ON and it was working very well to block a few websites on a schedule. And after a few month, it doesn't work any more. While it is possible that I scewed up the setting , I have tried so many settings.
So:DIR655 fw 1.32NA,hw A3,"Enable access control" is on with the desktop MAC address (used copy this MAC)(I have also tried my laptop MAC),web site filter is set to "deny",the router time is set using NTP dlink server,
View 3 Replies
View Related
Jul 27, 2012
First off, my router is a D-Link DIR-655, firmware v2.07. I'm trying to port forward port 25565.
My port forward settings are this:
However, when I use this open port checker, it claims that I don't have that port open. It looks like this, without the blurred out parts:
Added note: The way I want to use it is by my IP (xxx.xxx.xxx.154:25565). I have the software installed to do so (I'm using a minecraft server, connecting through minecraft), but I can't enter my IP in the IP address field, it says that it's out of the range of the LAN.
View 2 Replies
View Related
