hardware version D3, FW 4.10 and 4.11 same problem.
i tried with 4 wlan adapters: two of them support 802.11b/g, they always work find no matter which settings. the other two support 802.11b/g/n, as default "n" is enabled, so does DIR-615, both wlan adapters can be connected to DIR-615, they get their LAN-IP, but they can access neither DIR-615(no respone to ping) nor internet. but if i disable "n" mode either in the adapter or in DIR-615, everythin works fine, of course only with 54mbit max.
I have a DSL router Pirelli PDF A1000G.I have a Linksys e3000 and I have a dap-1522.When I bought a dap-1522 I thought it could do access point in fact i saw many videos in dlinktv before choosing an access point from DIY with mike etc to youtube there are 2 videos one showing bridged mode and another ap mode!Now what happens is this I have upgraded from firmware 1.11 that came as default to 1.21 i connect it wired to my linksys e3000 when it is connected with the ethernet cable wired I can connect to the internet and navigate and open sites and my ps3 can connect to it but my range is not very good only 40%!
Now I bring it downstairs remove the ethernet cable and connect it to the power and then you can connect to it but since it isn't connected to my router which is upstairs i can't access websites neither can I play on my ps3!I don't know does only ap mode works when it is connected to the router wired because what happens is if you don't put ethernet cables in the back of the dap-1522 and just connect it to power then here doewnstairs you can connect to the dap-1522 my signal is like 87% but while I'm connected with my laptop I can't access websites and in the ps3 I can't connect!
and choose access points there are (4) listed: dap-1522, dap-1160, dap-1353 and dap-2553, I thought of buying dap-1522 because it could support abgn while 1160 only supports g and 1353 only supports n to repeat to signal here downstairs and be a good access point!
Jason9 i'm having the exact same problem as above, don't mean to hijack but I'm using talktalk isp, I have AVG 9.0 and have a static IP and forwarded the required port on the router.
We are deploying a new office and exploring the options for WLAN deployment. We were pretty impressed with 3500 series APs and that it supports CleanAir.However, we have decided to go for standalone AP deployment model now. As 3500 does not work in standalone mode, so we are looking for APs that can work in standalone mode ( and later can be converted to lightweight if needed). We can go for 1140 in that case. However, it would be better for us to know the main differences between features supported by 3500 lightweight AP and 1140 standalone AP. CleanAir looks like the main one. Are there other important ones as well?
I have a WAP54G v3.1 running firmware version 3.05.01 and a WRT54G v3 running Tomato v1.28. The WAP54G is configured client mode and works perfectly. However, I was not able to get the two to communicate with WPA2 security - maybe, I just didn't try hard enough? Both devices are capable of doing WPA2 with AES but client mode doesn't seem to work with WPA2? I had to drop back to WPA-AES to make it work. Why is this?
I recently bought a Cisco E2500 for work, and after setting the router to Bridge Mode, I am unable to access the router web interface. I tried both the old IP address (192.168.1.1) and the IP address that I entered when I was configuring Bridge mode, but I couldn't get either to work. I have always tried resetting the switch to factory defaults and trying again to make sure I didn't type anything wrong, but to no avail. The wireless and everything works as it should, I just can't get back into the router to change any of my settings.
We have three brand new E4200 routers, all using the most current firmware (1.0.02). They are all in bridged mode, however when I attempt to enable the guest network on each of them, the config shows it as active, but it never shows up as visiible SSID. In previous posts, I've seen people saying that I need to do a complete hard reset of the router and re-enter all the configs again to get the guest network active. Is this true? I'd hate to think that I have to hard reset and reconfigure all three of these APs, just to get the guest network enabled.
The DIR-825 wireless simply doesn't work. When I called tech support, we cleared some settings and hard-powered the unit on/off and it finally turned on the wireless radio. A couple weeks later I pull out my laptop to use in the house via wireless and the wireless on the DIR-825 is OFFLINE AGAIN...fallen and it can't get UP.Is anyone having issues with keeping their wireless online? OK - powered it off for 5 minutes...now the wireless is working. I think changing configuration settings causes the thing to lock up.
Recently I bought a Windows 8 (64bits) computer, which is now part of my home network, but it has problems with Shareport. The other computers can be easily connected to a USB printer on my DIR-825 (HW B1) router, but the W8 computer refuses to completely install Shareport (both the CD version and the latest download v1.17). I also tried Shareport-Plus v4.11 (found on the DIR 835 page), which did install correctly, but was still unable to see the USB printer. What can be done? Can D-Link provide a new version of Shareport?
I can't get my brand new DCS-930L cam to connect to my network by using the WPA / WPA2 encryption. Works ok wired, with WEP or with no encryption enabled. Red led is on the front. I've tested sw version 1.02, 1.03 and the latest 1.04b03. Same result: WPA doesn't work. I have a Thomson TG789 Gateway/Router as provided by my ISP. All other units in the network works perfectly fine on WPA i.e. PC, Mac, printers, mobile phones etc etc.
Edit I've found a work-around. It's on page 2: [URL]
I'm having this really weird issue with my DIR-655 revB. I have some port forwarding rules set up and externally they work fine. However, if I try connecting to my IP address using those same ports from a computer within my LAN, it won't connect.
Externally, I can ping my WAN address and connect through forwarded ports. No problems. Internally, pinging my WAN address apparently works (just now is the first time that's worked for me), however I can't access any of my computers using the WAN IP and port forwarded ports. I can access them by going directly to their hostnames or LAN IPs.
Things I've tried:
-Disabling/enabling firewalls on all computers involved
-Disabling/enabling QoS engine
-Disabling/enabling DNS relay
-Disabling/enabling Advanced DNS
-Adding custom nameservers from Google and Comodo
-Restarting computers
-Clearing DNS cache (I use a dynamic DNS name which works externally but not internally. This gets the correct IP internally and connecting directly to the IP doesn't work either.)
-Modifying the NAT Endpoint Filtering settings
I have an external DSL modem connected to the router using PPPoE if it matters.
The weird part is that it works externally but I've modified all of the values I can think of in the config with no luck. I upgraded to the DIR-655 from a DIR-615 which had all these settings in it and worked fine (until it started acting up which is why I replaced it).
I realized that when I connect dir825 on bridging mode to my current voip router provided by my ISP (dvg-n5402) ,shareport does not work as it seems to be using the default gateway to find the usb, which in this case default gateway goes to the gateway of my voip router. Is there any way that I can make shareport use the gateway of my dir825 instead?
Like others I see on this board, we've got middle- and high-school age kids whose access to FB and other sites needs to be controlled/scheduled.
I thought the DIR-655 was great, in that it has features that, on the face of it, would seem to be ideal for blocking domains and restricting access.
My problem: I've never been able to get this to work.
I've set up schedules and created lists of domains that I want to limit access to according to the schedules, but the only constraint I've ever gotten to stick is blocking access completely to the router.
*None* of the schedule-based or website-based access controls have ever worked; I'll put the block in place to my daughter's computer's MAC address so she shouldn't be able to get to youtube or facebook, save, bounce the router, but then I go by her room and she's still busily chatting away online to her FB friends.
Based on similar posts I've seen on this forum, this may not be a unique problem.
So in a nutshell, this is what I want to do:
1) Block certain computers (identifiable by MAC address)
2) from being able to get to particular named domains (and any of their sub-domains)
3) according to a schedule that I can create and modify.
My preference would be to do this in the router, but again, responses I've seen here suggest that may not be possible.
My DIR-655: Hardware Version: A4 Product Page: DIR-655
The problem is that Website Filer doesn't work if on STEP 3: SELECT MACHINE of Access Control the machine was selected by MAC address. When the machine was selected by IP everything is fine.The problem is that IP addresses are assigned dynamically, so how to make sure that the policy would be applied to the same machine?
I just got my DIR 825. It had 2.02NA Firmware in it. It had a few options that I wanted to use but didn't work. So I thought I would update firmware. I follow the instruction from dlink to install firmware. So I loaded 2.03 and noticed internet connection not working. So then I loaded 2.05 part1 and part2. Still could get internet connection to work but the reason to upgrade the option I wanted worked. So then I loaded 2.06 and still same result. No internet connection. So then I loaded the original firmware back in and internet connection works. Why doesn't the internet work on the other firmware updates. I got the updates from dlink website. I would like to update firmware
I had the website filter ON and it was working very well to block a few websites on a schedule. And after a few month, it doesn't work any more. While it is possible that I scewed up the setting , I have tried so many settings.
So:DIR655 fw 1.32NA,hw A3,"Enable access control" is on with the desktop MAC address (used copy this MAC)(I have also tried my laptop MAC),web site filter is set to "deny",the router time is set using NTP dlink server,
First off, my router is a D-Link DIR-655, firmware v2.07. I'm trying to port forward port 25565.
My port forward settings are this:
However, when I use this open port checker, it claims that I don't have that port open. It looks like this, without the blurred out parts:
Added note: The way I want to use it is by my IP (xxx.xxx.xxx.154:25565). I have the software installed to do so (I'm using a minecraft server, connecting through minecraft), but I can't enter my IP in the IP address field, it says that it's out of the range of the LAN.
I tried to upgrade to 2.05NA several times and there always ends up being an issue that support is too sad to give the correct answer to and just puts a consumer thru "jumping thru hoops" and getting nowhere.2.05NA (actually started with 2.03NA) first caused a problem with limiting my upload speed to 1024mb. I happened across the fix on another forum and tried it and it worked. It was the default QoS setting D-Link changed after version 2.02NA and refuses to release a new firmware to fix this for everyone. Why they don't release a new FW that fixes the issue but keeps things promised on the package working is beyond me. Now, I purchased a D-Link DNS-323 and I finally got drives to fill it some time back. If 2.05NA is loaded, the Easy Search Utility will not connect to the NAS. I have tried the version the NAS came with AND the latest version offered. It will see the NAS upon 1st launch of the latest Easy Search Utility, but it will not connect and then it disappears if you relaunch the utility and won't return until a reboot. Bottom Line: it will not connect with 2.05NA loaded. It works fine with 2.02NA.
What is the setting that D-Link has screwed over here also that is causing this problem? It is pretty sad that their own hardware items won't play well together unless you run old FW. What setting D-Link changed that is making the D-Link DIR-825 not connect to the D-Link DNS-323 NAS when the DIR-825 has 2.05NA loaded. I have a DIR-825 Rev. B1 and a DNS-323 NAS with its latest firmware. I am using 2.02NA on the router since that is the only one that works and is the latest stable release(other than the DHCP reserve issue), no matter what D-Link wants to try to make people think. I won't try their support since they NEVER did give me the fix for the QoS upload issue and when I asked them to put it as a sticky in this forum when I found the answer somewhere else....well, there is no sticky as we all know. I would like to be able to have the DHCP Reserve issue working too, but I would like to connect to my NAS more at this point.
Region : Austria Model : TL-MR3420 Hardware Version : V2 Firmware Version : TL-MR3420_V2_121206 ISP : 3
I am using a MR3420 V2 together with a E398 modem. The connection works well, but I can't do any port forwarding (virtual server). Using another router (Tiny Dovado) with the same E398 modem works flawlessly to forward ports.
Region : Germany Model : TL-MR3040 Hardware Version : V1 Firmware Version : ISP :
Just got TL-MR3040 from amazon, not very happy that it is version 1, they could at least mention it in the description, but whatever...The problem is, i can not make it work with my PC laptop(thinkpad x120e with Windows 7 64 bit). Which means,1 not possible to get into web interface to configure it, and 2 if i configure it with old powerbook (os x 10.4) to share internet from usb stick, i can connect to it's wireless network but it doesn't share internet with my pc laptop,while mac and ipad working perfect...I've try to log in into web interface through the cable, still no luck...Not sure i want to re-install the whole system on my laptop just to see if it will change anything, it works with any other router, and usb sticks...
I have (2) 942-L, and (1) 5222-L on one network. port forwarding set on router; (942) 192.168.1.3:1024, (942) 192.168.1.4:1025, and (5222) 192.168.1.8:80. no matter if all 3 are connected to dViewCam, only two will work at a time. Disconnect any third, and they work fine. reconnect 3rd, and one disconnects intermittently. On a side note, if I run a different program on another computer (iMac); i.e. IP Camera Viewer, they all work fine. I know, I know, but I like DViewCam, because it's the only thing running the PC computer.
I recently set up two cameras. I had set up one for motion detection and email to a gmail account. It seemed to work fine, but then for some reason the motion detection tab didn't show the room like it did before. It doesn't show any picture or anything like it did before, so I couldn't choose the squares to choose the detection area. This is through mydlink account->camera info->advanced settings, and logging in to the camera remotely.So I switched to the other camera, and got it working as of last week. But now, the motion detection doesn't work anymore? It appears to be related to the username/password for the email account. I can no longer send test emails, it says invalid username/password, though the exact same values worked last week, and I didn't change anything. I tried resetting it, then setting it again, but no luck.
Region : India Model : TL-MR3420 Hardware Version : V1 Firmware Version : 3.12.21 Build 120523 Rel.37880n ISP : Reliance
I've just set up a MR3420. It works fine in "WAN only" mode and provides access via our ADSL modem. It also works fine in "3G only" mode and provides access via a Reliance Netconnect+ USB modem (a Huawei E150 I think). I updated the firmware to the latest version in order to get it to work with the USB modem.
The problem I have is that when I set it to "3G preferred" it doesn't seem to connect over 3G. I can see it tries to connect but then fails and then WAN takes over. The connect and disconnect options are greyed out on the 3G page so I am unable to manually get it to retry. I've tried leaving it for a long time but it doesn't seem to connect over 3G ever. I've tried setting 3G to connect on demand and connect automatically but both behave the same.
For some reason I can't get Access Control/Webaccess Filters working on my Dir-655 w/ 1.35NA. I've tried it with MAC and IP Address without any success. I've also enabled/disabled/enabled DNS Relay, recreated the rules, recreated the filters, etc. Nothing.
Region : Netherlands Model : TL-WR1043ND Hardware Version : Not Clear Firmware Version :
I installed my brand new TP-Link router and both wired and wireless internet connection work perfectly fine. But when I tried to secure the wifi with a password (I followed the instructions on last page of installation guide) I can not connect to the internet any more. After entering the correct password, both iphone and mac-book simply say "unable to join the network". I selected WPA2-PSK-personal as recommended. For now I switched off the security settings, but I live in a building with many neighbours and they are now consuming most of my bandwidth (apparentlyI am surrounded by illegal downloaders
Region : UnitedStates Model : TL-WR702N Hardware Version : V1 Firmware Version : 4.18.107 Build 121123 Rel.31456n ISP : COMCAST
This is the 2nd WR702N I have purchased. The first worked as a repeater for a short time and then failed with the fading symptom. I returned it. The second did not work as a repeater even for a short time. The signal is OK for a few seconds and then fades out. I updated the firmware.
Is there any chance the Wireless Repeater mode work with WPA2-AES ?If not, which model of AP should I buy to connect it with my wap54g as Wireless Repeater?
i got a Dir-655 router and Dell 1501 wireless -N mini PCI card (802.11 bgn compliant). Router was set to mix mode but my desktop Dell XP8300 can connect only till G mode.
1) I search on web and some said that i need to set my router to N mode only for my desktop to connect to N mode. IS THIS SOLUTION CORRECT??
2) Another issue was my sis got other old brand latop which can only connect to B mode, if i set to N mode only, she won't be able to connect it right?
I have an problem with VPN connection on notebooks. Sometimes the VPN connection works perfectly, and other times it just doesn't work at all.The Cisco VPN client software is version 5.0.04.0300. Operating system is Windows XP Prof SP2.When the connection fails, the client statistics window shows "Bytes Received: 0".Rebooting the system, has no effect
Normally, when one right clicks on a drive letter having opened 'My computer', then select 'Sharing' there is a warning about sharing a whole disk and the option to accept anyway.One laptop doesn't offer that. It just shows the admin share of C$ immediately. If I choose 'New' at the bottom of the panel a new drive letter and drive name can be entered but it can never be accessed over the network! It shows up in the workgroup but I get a network error 'Network path not found' if I try to access it. I can ping the laptop from anywhere by name and IP address.The laptop can access all the other PCs without any problem.
So, my desktop, running windows 7, can no longer connect to the internet. It has no problem connecting to the router, but it will not receive packets. I double checked my connection using my laptop and it works with wireless and wired connections, so I know it's something with my desktop. I would really like to avoid doing a reinstall, I don't have anywhere to back my data up to.
