I have several ports opened on my DIR-655 A3, pointing to specific ports on a NAS server i have on my network.
I've already try this:
- Reboot the router
- Erase all Virtual Server Settings and try open only one port
- Re-flash the router with latest European firmware - 1.34b05EU
I had the website filter ON and it was working very well to block a few websites on a schedule. And after a few month, it doesn't work any more. While it is possible that I scewed up the setting , I have tried so many settings.
So:DIR655 fw 1.32NA,hw A3,"Enable access control" is on with the desktop MAC address (used copy this MAC)(I have also tried my laptop MAC),web site filter is set to "deny",the router time is set using NTP dlink server,
I have a W7 PC 64 bit system and I've been trying to port forward the port 25565 for my Minecraft server. However for some reason (even after port forwarding the right one) people still can't connect. When I check on Open Port Check Tool - Test Port Forwarding on Your Router It still says that the port 25565 is closed!I've even created an Inbound and Outbound rule in the Windows Firewall advanced settings. I use Avira Anti-vir fyi..
View 19 Replies View RelatedComcast sent out a new modem a few days ago. The reason for this was our internet had gone out for a while, they came in and said our modem was fried. I have internet access by directly wiring from the modem to my computer.My router doesn't work anymore. I have a local network, but no internet access. I'm using a Linksys WRT54G, and I don't really know what to do.As far as I remember, setting everything to defaults and factory settings was how I set up my router in the first place and it just worked.
View 11 Replies View RelatedI have a 3845 running 12.4.13a which I want to upgrade to 12.4.24.After upgrade one of the interface that is configured for frame relay doesn't work anymore.In fact is the "service-module t1 timeslots" commands that can not be executed and the router throws that error.I tested this behaviour on two 3845s and the result is the same.Is this a bug or is an workaround for it?
View 3 Replies View RelatedAm running firmware ver 1.00.19. Set up DDNS with DynDns.Org and all is well. Set up virtual server with DDNS info. Trying to connect to an IPcam (Foscam 8905W). IPcam is set up with static IP with ip outside Belkins DHCP range.
Problem: When trying to access the IPcam through the internet (DynDns) Belkin takes me right to the Belkin router Setup screen, not to the virtual server settings (IPcam). I was able to do it a couple of months ago,but not now. I may have upgraded my firmware in that time from 1.00.12.
Just replaced my SMC Gateway with a Cisco Home Networking Modem, router doesn't see DCS 930 cameras. Working perfect before. I start the wizard, I plug in camera power, plug in ethernet cable for setup, light is green as requested, searches for camera, comes up "No Cameras found". Called ISP provider to reset modem, still no go. Tried a wireless setup using the "buttons", no go. Reset cameras..
View 9 Replies View RelatedI can backup the router settings on an RV110W, but not restore them. I get an "unable to write" error. (probably not the exact verbiage). Defective router, or firmware issue?
View 14 Replies View RelatedRegion : UnitedKingdom
Model : TD-W8968
Hardware Version : V1
Firmware Version : latest
ISP : french orange
I am trying to set up port forwarding on this router but it seems I need to use virtual servers but in all the guides there is a menu for this under the advance settings nat menu.I do not have that option, I have downloaded the latest firmware but still nothing.
Region : Mexico
Model : TD-W8968
Hardware Version : V1
Firmware Version : the last version of this web page, i forgot number
ISP : TELMEX (infinitum)
i have some problems to configure the port forwarding in my router, don't it work ! but the port number 80 it works with my sub-domain in the internet. after i change this port to 8080 still dont work the port forwarding. the FTP server its ok.
[code]......
I have an DLINK-dir 815 router.. I have tried for 10 hours to get broadcast IP to work, no luck.. All html/javascript modifications = no luck..The WOL works on LAN, but not over internet, so I figure it's the broadcast IP that needs to be virtual servered?
View 9 Replies View RelatedI wonder what the difference is between the virtual server and the port forwarding because the router I was using previously had only port forwarding. When should I use virtual server instead of port forwarding?
View 1 Replies View RelatedI have DIR-601 wireless router with two computers connected: Server (192.168.1.2) and Client (192.168.1.3 on Ethernet Port and 192.168.1.4 on Wireless)
I also use dlinkddns.com and my router's public IP is mapped as abc.dlinkddns.com.
In the router Virtual Server section, it is configured as:
Public Port: 3389 (for Remote Desktop)
Private Port: 3389
IP Address: 192.168.1.2 (server's IP)
I am expecting this to allow the client to access the server via windows Remote Desktop.
The current situation is:
- When wireless is on, the client can access the server's Remote Desktop
- When wireless is off and client is connected by wired Ethernet, the client cannot connect to the server's remote desktop. After timeout, the error msg is "Remote Desktop can't connect to the remote computer for one of these reasons: ...".
- When the client is in another network, it can connect to the server through the Internet.
I am sure it's not the client's problem because it can access via wireless or remotely from another network. It's not the router's virtual server config problem for the same reasons. Will it be a bug in the router? (hardware version: B1, firmware version: 2.00NA).
I've got a DIR-825 RevB Firmware V2.06NA on a static IP wan connection routing to a SBS2008 server and 10PC's. The server is serving mail, web, and files. Router has virtual servers setup for http, https, smtp, imap, imapssl, smtpssl, pptp, remote desktop, and a few others.
Everything works fine, but the routers https forwarding stops running periodically about half an hour after reboot. The server's working fine, but it doesn't see the https request, it looks like the router is trying to serve the 443 request itself. After a router reboot everything is back to normal.
I've replaced the router with another dir-825 and it has the same issue.
Region : Others
Model : TD-W8961ND
Hardware Version : V3
Firmware Version : 3.0.0
ISP :
My router is TDW8961ND
The firmware version is 3.0.0
The hardware version is 3.0
I am trying to have a virtual http server at port 80 but when I do this and save, I get this message: "Notice: The WAN HTTP port of CPE will be chaged to 8080 if submit successfully."Then after that I cannot access the server at port 80.
Why is loop-back only working on ports forwarded in the Virtual Server section and not Port Forwarding or even DMZ? I have seen a post about loop-back on the DIR-655 from a while ago that had said to disable SPI and change NAT Endpoint to independent, I have done this and loop-back still doesn't work.
View 1 Replies View RelatedI'm trying to connect a Cisco 2811 using an octal cable to a Juniper MX480 console port.Since the distance between Cisco 2811 and router is 20ft, im using couplers and a straight-through cable for the lack of slack. This wiring doesnt work, however in another city it works going straight from the Cisco 2811 octal cable to the router since they are in the same rack.
View 4 Replies View Relatedhardware version D3, FW 4.10 and 4.11 same problem.
i tried with 4 wlan adapters: two of them support 802.11b/g, they always work find no matter which settings. the other two support 802.11b/g/n, as default "n" is enabled, so does DIR-615, both wlan adapters can be connected to DIR-615, they get their LAN-IP, but they can access neither DIR-615(no respone to ping) nor internet. but if i disable "n" mode either in the adapter or in DIR-615, everythin works fine, of course only with 54mbit max.
so what can i do to use the n mode?
The DIR-825 wireless simply doesn't work. When I called tech support, we cleared some settings and hard-powered the unit on/off and it finally turned on the wireless radio. A couple weeks later I pull out my laptop to use in the house via wireless and the wireless on the DIR-825 is OFFLINE AGAIN...fallen and it can't get UP.Is anyone having issues with keeping their wireless online? OK - powered it off for 5 minutes...now the wireless is working. I think changing configuration settings causes the thing to lock up.
View 1 Replies View RelatedRecently I bought a Windows 8 (64bits) computer, which is now part of my home network, but it has problems with Shareport. The other computers can be easily connected to a USB printer on my DIR-825 (HW B1) router, but the W8 computer refuses to completely install Shareport (both the CD version and the latest download v1.17). I also tried Shareport-Plus v4.11 (found on the DIR 835 page), which did install correctly, but was still unable to see the USB printer. What can be done? Can D-Link provide a new version of Shareport?
View 3 Replies View RelatedI can't get my brand new DCS-930L cam to connect to my network by using the WPA / WPA2 encryption. Works ok wired, with WEP or with no encryption enabled. Red led is on the front. I've tested sw version 1.02, 1.03 and the latest 1.04b03. Same result: WPA doesn't work. I have a Thomson TG789 Gateway/Router as provided by my ISP. All other units in the network works perfectly fine on WPA i.e. PC, Mac, printers, mobile phones etc etc.
View 1 Replies View RelatedI have a DSL router Pirelli PDF A1000G.I have a Linksys e3000 and I have a dap-1522.When I bought a dap-1522 I thought it could do access point in fact i saw many videos in dlinktv before choosing an access point from DIY with mike etc to youtube there are 2 videos one showing bridged mode and another ap mode!Now what happens is this I have upgraded from firmware 1.11 that came as default to 1.21 i connect it wired to my linksys e3000 when it is connected with the ethernet cable wired I can connect to the internet and navigate and open sites and my ps3 can connect to it but my range is not very good only 40%!
Now I bring it downstairs remove the ethernet cable and connect it to the power and then you can connect to it but since it isn't connected to my router which is upstairs i can't access websites neither can I play on my ps3!I don't know does only ap mode works when it is connected to the router wired because what happens is if you don't put ethernet cables in the back of the dap-1522 and just connect it to power then here doewnstairs you can connect to the dap-1522 my signal is like 87% but while I'm connected with my laptop I can't access websites and in the ps3 I can't connect!
and choose access points there are (4) listed: dap-1522, dap-1160, dap-1353 and dap-2553, I thought of buying dap-1522 because it could support abgn while 1160 only supports g and 1353 only supports n to repeat to signal here downstairs and be a good access point!
i have a DIR-615 Rev C1, firmware 3.13.
After a reboot my password doesn't work anymore (wich is normal I guess) and all default passwords dont either. Such as ''Password'' or ''Admin''.
Edit I've found a work-around. It's on page 2: [URL]
I'm having this really weird issue with my DIR-655 revB. I have some port forwarding rules set up and externally they work fine. However, if I try connecting to my IP address using those same ports from a computer within my LAN, it won't connect.
Externally, I can ping my WAN address and connect through forwarded ports. No problems. Internally, pinging my WAN address apparently works (just now is the first time that's worked for me), however I can't access any of my computers using the WAN IP and port forwarded ports. I can access them by going directly to their hostnames or LAN IPs.
Things I've tried:
-Disabling/enabling firewalls on all computers involved
-Disabling/enabling QoS engine
-Disabling/enabling DNS relay
-Disabling/enabling Advanced DNS
-Adding custom nameservers from Google and Comodo
-Restarting computers
-Clearing DNS cache (I use a dynamic DNS name which works externally but not internally. This gets the correct IP internally and connecting directly to the IP doesn't work either.)
-Modifying the NAT Endpoint Filtering settings
I have an external DSL modem connected to the router using PPPoE if it matters.
The weird part is that it works externally but I've modified all of the values I can think of in the config with no luck. I upgraded to the DIR-655 from a DIR-615 which had all these settings in it and worked fine (until it started acting up which is why I replaced it).
We have a VPN setup for a customer between our shop and their shop 2.5 hours away. This is a Cisco 871.We had Verizon and the connection worked (still does) great! We had to switch providers as they sold to Frontier and were going to change our IPs anyways so why not switch to a faster provider instead.We switched to Charter. I have ZERO, NADA, ZILTCH knowledge of Cisco and I plan to keep it that was as they are way more complicated then they should be. Ill stay with my Sonicwall.....Anyways.... I took the config and did a find and replace for all the IP's, Gateways, DNS etc....I blasted that into the router and it took right off and connected up the VPN in a matter of 2 minutes. I was estatic as I knew I was going to sleep good that night not worrying about it..............Untill the next day at 11 am when I get a phone call from work saying the connection was down.
I go and realize that the router cant see the outside world anymore, therefor was obviously not going to see the peer IP address. I was dumbfounded!. To make a long story short I tried reconfiging therouter with the same file. I even redid the find and replace and resaved it to no avail. Still no go, no internet. All the proper IPs, Gateways and DNS numbers are where they should be. To test that its the config and/or something to far above me. I re configed the router with the old config and hooked it back up to verizon, it took right off and reestablished the VPN and was working.
I am using ASA5520 with webvpn for file sharing. But recently we just upgraded the OS that accommodate file shared folder from win2003 R2 32bit to windows server 2008 R2 64bit. Now I have a problem with accessing file share by ASA webvpn, it appears error contacting host, we have tested the file shared of webvpn on the other OS windows 2003 and windows 2008, they are working on these OS except win2008 R2. Current the ASA OS version is 8.0(2). And the windows firewall has been disabed.
View 3 Replies View RelatedLike others I see on this board, we've got middle- and high-school age kids whose access to FB and other sites needs to be controlled/scheduled.
I thought the DIR-655 was great, in that it has features that, on the face of it, would seem to be ideal for blocking domains and restricting access.
My problem: I've never been able to get this to work.
I've set up schedules and created lists of domains that I want to limit access to according to the schedules, but the only constraint I've ever gotten to stick is blocking access completely to the router.
*None* of the schedule-based or website-based access controls have ever worked; I'll put the block in place to my daughter's computer's MAC address so she shouldn't be able to get to youtube or facebook, save, bounce the router, but then I go by her room and she's still busily chatting away online to her FB friends.
Based on similar posts I've seen on this forum, this may not be a unique problem.
So in a nutshell, this is what I want to do:
1) Block certain computers (identifiable by MAC address)
2) from being able to get to particular named domains (and any of their sub-domains)
3) according to a schedule that I can create and modify.
My preference would be to do this in the router, but again, responses I've seen here suggest that may not be possible.
My DIR-655:
Hardware Version: A4
Product Page: DIR-655
The problem is that Website Filer doesn't work if on STEP 3: SELECT MACHINE of Access Control the machine was selected by MAC address. When the machine was selected by IP everything is fine.The problem is that IP addresses are assigned dynamically, so how to make sure that the policy would be applied to the same machine?
I just got my DIR 825. It had 2.02NA Firmware in it. It had a few options that I wanted to use but didn't work. So I thought I would update firmware. I follow the instruction from dlink to install firmware. So I loaded 2.03 and noticed internet connection not working. So then I loaded 2.05 part1 and part2. Still could get internet connection to work but the reason to upgrade the option I wanted worked. So then I loaded 2.06 and still same result. No internet connection. So then I loaded the original firmware back in and internet connection works. Why doesn't the internet work on the other firmware updates. I got the updates from dlink website. I would like to update firmware
View 9 Replies View RelatedFirst off, my router is a D-Link DIR-655, firmware v2.07. I'm trying to port forward port 25565.
My port forward settings are this:
However, when I use this open port checker, it claims that I don't have that port open. It looks like this, without the blurred out parts:
Added note: The way I want to use it is by my IP (xxx.xxx.xxx.154:25565). I have the software installed to do so (I'm using a minecraft server, connecting through minecraft), but I can't enter my IP in the IP address field, it says that it's out of the range of the LAN.
I tried to upgrade to 2.05NA several times and there always ends up being an issue that support is too sad to give the correct answer to and just puts a consumer thru "jumping thru hoops" and getting nowhere.2.05NA (actually started with 2.03NA) first caused a problem with limiting my upload speed to 1024mb. I happened across the fix on another forum and tried it and it worked. It was the default QoS setting D-Link changed after version 2.02NA and refuses to release a new firmware to fix this for everyone. Why they don't release a new FW that fixes the issue but keeps things promised on the package working is beyond me. Now, I purchased a D-Link DNS-323 and I finally got drives to fill it some time back. If 2.05NA is loaded, the Easy Search Utility will not connect to the NAS. I have tried the version the NAS came with AND the latest version offered. It will see the NAS upon 1st launch of the latest Easy Search Utility, but it will not connect and then it disappears if you relaunch the utility and won't return until a reboot. Bottom Line: it will not connect with 2.05NA loaded. It works fine with 2.02NA.
What is the setting that D-Link has screwed over here also that is causing this problem? It is pretty sad that their own hardware items won't play well together unless you run old FW. What setting D-Link changed that is making the D-Link DIR-825 not connect to the D-Link DNS-323 NAS when the DIR-825 has 2.05NA loaded. I have a DIR-825 Rev. B1 and a DNS-323 NAS with its latest firmware. I am using 2.02NA on the router since that is the only one that works and is the latest stable release(other than the DHCP reserve issue), no matter what D-Link wants to try to make people think. I won't try their support since they NEVER did give me the fix for the QoS upload issue and when I asked them to put it as a sticky in this forum when I found the answer somewhere else....well, there is no sticky as we all know. I would like to be able to have the DHCP Reserve issue working too, but I would like to connect to my NAS more at this point.
Region : Austria
Model : TL-MR3420
Hardware Version : V2
Firmware Version : TL-MR3420_V2_121206
ISP : 3
I am using a MR3420 V2 together with a E398 modem. The connection works well, but I can't do any port forwarding (virtual server). Using another router (Tiny Dovado) with the same E398 modem works flawlessly to forward ports.
Region : Germany
Model : TL-MR3040
Hardware Version : V1
Firmware Version :
ISP :
Just got TL-MR3040 from amazon, not very happy that it is version 1, they could at least mention it in the description, but whatever...The problem is, i can not make it work with my PC laptop(thinkpad x120e with Windows 7 64 bit). Which means,1 not possible to get into web interface to configure it, and 2 if i configure it with old powerbook (os x 10.4) to share internet from usb stick, i can connect to it's wireless network but it doesn't share internet with my pc laptop,while mac and ipad working perfect...I've try to log in into web interface through the cable, still no luck...Not sure i want to re-install the whole system on my laptop just to see if it will change anything, it works with any other router, and usb sticks...