I have a 3845 running 12.4.13a which I want to upgrade to 12.4.24.After upgrade one of the interface that is configured for frame relay doesn't work anymore.In fact is the "service-module t1 timeslots" commands that can not be executed and the router throws that error.I tested this behaviour on two 3845s and the result is the same.Is this a bug or is an workaround for it?
View 3 Replies
Network is 10.254.0.0/16
snag.gy/3Y8aN.jpg This is the network image.
This is my subnetted connections: http:[url]....
I can ping R2 to R5 but not R5 to R2. I have spent about 10 hours going through my network and code to no avail. I think it is the frame relay that's causing the error but not sure.. I just checked and I think R6 and R5 are not getting their OSPF updates by trying show ip route
Here are my configs: http:[url]....
I have a W7 PC 64 bit system and I've been trying to port forward the port 25565 for my Minecraft server. However for some reason (even after port forwarding the right one) people still can't connect. When I check on Open Port Check Tool - Test Port Forwarding on Your Router It still says that the port 25565 is closed!I've even created an Inbound and Outbound rule in the Windows Firewall advanced settings. I use Avira Anti-vir fyi..
View 19 Replies View RelatedComcast sent out a new modem a few days ago. The reason for this was our internet had gone out for a while, they came in and said our modem was fried. I have internet access by directly wiring from the modem to my computer.My router doesn't work anymore. I have a local network, but no internet access. I'm using a Linksys WRT54G, and I don't really know what to do.As far as I remember, setting everything to defaults and factory settings was how I set up my router in the first place and it just worked.
View 11 Replies View RelatedI had the website filter ON and it was working very well to block a few websites on a schedule. And after a few month, it doesn't work any more. While it is possible that I scewed up the setting , I have tried so many settings.
So:DIR655 fw 1.32NA,hw A3,"Enable access control" is on with the desktop MAC address (used copy this MAC)(I have also tried my laptop MAC),web site filter is set to "deny",the router time is set using NTP dlink server,
I have several ports opened on my DIR-655 A3, pointing to specific ports on a NAS server i have on my network.
I've already try this:
- Reboot the router
- Erase all Virtual Server Settings and try open only one port
- Re-flash the router with latest European firmware - 1.34b05EU
Main site have 8 departments and each department have 60 pc's,remaining sites each have 6 departments and in each department have 40 pc's and in the design of WAN connection you use frame relays and that is the 100% growng hosptals and clock speed is 64000 bits/sec and security must don't access the unautheraised users from out side....how can I do this?
View 5 Replies View RelatedProvider T1 handoff with two PVCs to their MPLS cloud to a 2911.One Internet PVC and one for the MPLS including a SIP trunk .
Is there a way to use QOS to have the router prioritize one PVC over the other.Always service the MPLS/SIP PVC over the Internet ONLY PVC?The MPLS/SIP PVC will have QOS for voice but needs to be prioritize.Other option will be to police down the Internet PVC to a value which will leave the required total Kb for the voice priority KB.(FR PIPQ works if the PVC is for voice only.)
I am having real problems trying to build resiliency into a hub and spoke frame relay scenario. I know the hub is a single point of failure. Is there any way to put some resilience into the network? There is 4 attached branch offices.
View 8 Replies View Relatedworking through a lab and can't seem to configure frame relay on subints. I assume it's not supported but this seems basic; am I doing something wrong?
View 4 Replies View RelatedI have been trying to make rip work on this frame relay with multipoint configuration (hub and spoke) and I also configured a loopback interface on each of the routers and configured rip with the loopback address. I observed that the routers (cisco 3600 series) are not sending or receiving any RIP updates through their serial interfaces but are sending through loopback interfaces i configured (debug ip rip).I can ping all routers but cant ping their loopback interfaces because RIP updates are not sent or received by them.
R1#debug ip rip
RIP protocol debugging is on
R1#
*Mar 1 00:09:46.759: RIP: sending v2 update to 224.0.0.9 via Loopback1 (1.1.1.1)
*Mar 1 00:09:46.763: RIP: build update entries - suppressing null update
[code]....
I started studying yesterday for CCNP Route and I'm already stuck. Stupid Frame relay. Basic topology attached, 1 Hub, 2 spokes. I have EIGRP working correctly and each spoke can see all routes correctly. The Hub is on a Multipoint interface with split horizon turned off.
View 15 Replies View RelatedI've a home lab which consists of three 2610xm routers and I have configured two routers back to back with FR subinterfaces. The commands are used are;
R1
frame relay switching
int s0/0
encap FR
no sh
clock rate 64000
frame-relay intf-type dce
[code].....
Everything works great with this config and I know how to configure without lmi too. My question is more for the CCNA exam and fill the gaps in so to speak. The question is when you configure FR with static mappings and inverse arp do you need actual frame relay switches on the other side of the link or can I configure on my home labs routers. I know I am gonna try and configure this as well, but can I configure multipoint on my third router with a different physical interface. Like R1 with s0/0 to R2 s0/0 and R1 s0/1 to R3 s0/0 with subinterfaces.
I 'm trying to set up a home lab with a couple of 28XX and 2651XM series routers.I would like to simulate a frame-relay connection between HQ, Branch1 and Branch2 . All of them are conneced to a PSTN switch (2811 router) via T1 cross over cables. The connectivity is like this. [code] I have configured all the routers and FR switch with necessary configuration. However the link between HQ and Branch1 is not coming up. On both the routers I could see the line protocol is down.I have pasted the configuration below.[code]
View 4 Replies View RelatedAs U know cisco feature for frame-relay is creating mfr link and binding them to physical interfaces I did so but my MFR links doesn't get up?
PS. router is ASR1004
frame-relay switching
interface MFR0 description Virtual FR ---> Serial0/0/0 no ip address encapsulation frame-relay IETF frame-relay lmi-type ansi frame-relay intf-type dce frame-relay route 908 interface Serial0/0/0 908!interface MFR1 description Virtual FR ---> Serial0/2/4:0 no ip address encapsulation frame-relay IETF frame-relay lmi-type ansi frame-relay intf-type dce frame-relay route 900 interface Serial0/2/4:0 900
interface Serial0/0/0 (Smart serial interface) description Serial ---> E1 no ip address encapsulation frame-relay MFR1
interface Serial0/2/4:0 (E1 serial interface) description Link ---> S no ip address encapsulation frame-relay MFR0
I am installing an ASA 5520 and I have a problem on accepring the incoming traffic from an external office connected via Frame Relay.
On my OUTSIDE interface I have both the internet traffic and the external office traffic incoming. What comes from the external office is visible as 10.1.0.0/16.
I have to allow this traffic to enter the internal network, without any control. I would also keep the original IP address.
I have configured the Firewall but I don't know how to setup the NAT.
I'm looking to test fram relay connections in a lab environment i'm building at home. I have a couple of 2610 routers that are barebones and am looking to get some serial modules. Are (2) WIC-2T's all I would need to create those test connections? Also on a side note are the any modules for the 2610 that have fast ethernet connections. I would like to have that so I can create a router on a stick model off of the 2600's.
View 1 Replies View RelatedIOS 15.1(4)M1.
I am trying to setup my new 2901 running 15.1(4)M1 for frame realy via a VWIC3-1MFT-T1/E1 card. Now I have set up plenty of frame relay connections via older serial cards, but I just cannot find any documentation on how to do this on one of the new VWIC3-1MFT-T1/E1s. None of the commands I am used to seem to even exist. None of the
encapsulation frame-relay ietf
frame-relay interface-dlci 16 ietf
seems to be there. How to configure the card in IOS 15?
We have frame relay T1 circuit at one of our remote site. Which is connected to our core frame relay router which have DS3 circuit.Now we bought second T1 line at remote site and now I have to configure Bounded T1 with Cisco 1921 router.good config example or document on how to configure frame relay bounded T1 ?
View 1 Replies View RelatedTransitioning from 3825 to 3945 (OS is 15.0(1r)M13 c3900-universalk9-mz.SPA.151-4.m4). Turning on FDL on the 3825 was easy but the same command on the 3945 doesn't work.
View 3 Replies View RelatedI have a NM-1CE1U working on my router 2600 , configured with frame-relay . But seems it does not work on my router 2811. I have check that the replacement is HWIC-1CE1T1-PRI , right ？
But the problem is these two modules have different interface type , I want to keep my cable interface type and find one module card working on 2800 or 2900 router , can configure frame-relay.
QoS on an MFR interface/subinterfaces. We have a remote site with two bundled T1's terminating on a 2951 router for a total bandwidth of 3072. The circuit is provided by Paetec and the subinterfaces are designated for internet and MPLS traffic respectively. The issue we are facing is with outbound voice quality. It seems that no matter how we apply QoS, either to the main MFR interface or the MFR subinterfaces, voice packets do not seem to be prioritized. We tried FRTS, which slowed the entire link down to a crawl, we tried applying a class map to the main interface as well as a service policy, none of which seemed to affect anything.
class-map match-all VOICE
match ip dscp ef
class-map match-any SIGNALING
match ip dscp af31
match ip dscp cs3 (code)
I have catalyst 3750 I want to controle traffics on every port I have tried Frame-Relay Traffice shaping and Quality of service but there is no support for these commands in the switch.do we have any way to limit traffic on every port in catalyst 3750 and 2960 switches ?
View 4 Replies View RelatedI need to get some low volume, interactive data, prioritized on frame relay PVCs across our network. I have followed the CBWFQ examples from cisco.com, but my test packets are still showing latency over 1 second. My lab set up has a corporate connected gateway router linked via FE to testrouter 50. TR51 has a T1 frame relay loop to another router acting as a frame relay switch. The other side of the FR switch has a 56k link to testrouter51. I am sourcing test pings from my desktop PC, that are marked as AF43, and leave at a rate of 1/second, when the response comes back in time. I am using a Smartbits to generate some default class traffic at a rate of about 56Kbps only in the 'outbound' direction, toward TR51, as this emulates a file copy from corporate to remote sites, that is causing the AF43 traffic to suffer. Here is the relevant config on the TR50 device:
class-map match-all rtu-data
match ip dscp af43
!
policy-map frame-56
class rtu-data
priority percent 20
class network-mgt-data
bandwidth percent 5(code)
Application is that need to configure the VOIP with the existing Frame relay network ,where VOFR command is not shown in the router when type yhe command router config#dial-peer voice 123 need vofr On the 3945 router where in the router it is not accepting the above command,
View 8 Replies View Relatedwhy the WAN protocols like Frame-relay, HDLC and PPP are called Layer2 protocols?What is the address scheme they use?
View 5 Replies View RelatedI am trying to configure two 3845 routers to act as dhcp server and dhcp relay. Clients are connected to the router that relays all dhcp requests to the vrf instance which is used to connect it to the router wich is running dhcp server.
Router1
ip vrf dhcp_dns
rd 8:1
int gi0/0
ip vrf forwarding dhcp_dns
ip address 192.168.200.5 255.255.255.248
[code]...
So far I can see dhcp requests coming from the R1 and dhcp server on R2 replies with the dhcp offer but PC is not getting any ip.
We have a VPN setup for a customer between our shop and their shop 2.5 hours away. This is a Cisco 871.We had Verizon and the connection worked (still does) great! We had to switch providers as they sold to Frontier and were going to change our IPs anyways so why not switch to a faster provider instead.We switched to Charter. I have ZERO, NADA, ZILTCH knowledge of Cisco and I plan to keep it that was as they are way more complicated then they should be. Ill stay with my Sonicwall.....Anyways.... I took the config and did a find and replace for all the IP's, Gateways, DNS etc....I blasted that into the router and it took right off and connected up the VPN in a matter of 2 minutes. I was estatic as I knew I was going to sleep good that night not worrying about it..............Untill the next day at 11 am when I get a phone call from work saying the connection was down.
I go and realize that the router cant see the outside world anymore, therefor was obviously not going to see the peer IP address. I was dumbfounded!. To make a long story short I tried reconfiging therouter with the same file. I even redid the find and replace and resaved it to no avail. Still no go, no internet. All the proper IPs, Gateways and DNS numbers are where they should be. To test that its the config and/or something to far above me. I re configed the router with the old config and hooked it back up to verizon, it took right off and reestablished the VPN and was working.
Just replaced my SMC Gateway with a Cisco Home Networking Modem, router doesn't see DCS 930 cameras. Working perfect before. I start the wizard, I plug in camera power, plug in ethernet cable for setup, light is green as requested, searches for camera, comes up "No Cameras found". Called ISP provider to reset modem, still no go. Tried a wireless setup using the "buttons", no go. Reset cameras..
View 9 Replies View RelatedI have a laptop that I want to sell, therefore I went to somebody to see my laptop and wanted to connect to his wifi. After repeatedly entering the pass for the wifi ,the wifi was still not connecting.
1. My laptop will see his wifi but after entering the pass will not connect
2. The pass is correct because I introduced the same pass on my mobile and I was able to connect to his wifi through my mobile
3 My laptop wifi is working fine because when I went home it connects automatically on my home wifi
4. I tried to open and close his router but I faced same problem.
I've just bought this wireless usb today and attempted 2-3 times to be able to connect with my router (D-Link's DIR-601) but it for some reason failed to do so, until the little usb didn't have its green light flashing anymore... and when i reconnected it to my Windows XP it rang its error sound... and I kept having this message from the Wireless Wizard that it's not connected appropriately or something...and that i have to run the setup wizard again.
View 1 Replies View Relatedhow to configure dhcp relay agent and how it's work
View 1 Replies View RelatedI have two ASA 5515 configured as active / standby. I configured the failover and I checked for proper operation. But when I configured access rules and NAT, I realized that the failover does not work anymore: two interfaces, inside and outside, are "Unknow (Waiting)". The other LAN interface and management are "Normal (Monitored)." [code] It is possible that some access rule deny the communication between the two asa?
View 9 Replies View Related
