Cisco WAN :: 2610 Testing Out Frame Relay Connections
Mar 13, 2012
I'm looking to test fram relay connections in a lab environment i'm building at home. I have a couple of 2610 routers that are barebones and am looking to get some serial modules. Are (2) WIC-2T's all I would need to create those test connections? Also on a side note are the any modules for the 2610 that have fast ethernet connections. I would like to have that so I can create a router on a stick model off of the 2600's.
View 1 Replies
ADVERTISEMENT
Apr 23, 2013
Network is 10.254.0.0/16
snag.gy/3Y8aN.jpg This is the network image.
This is my subnetted connections: http:[url]....
I can ping R2 to R5 but not R5 to R2. I have spent about 10 hours going through my network and code to no avail. I think it is the frame relay that's causing the error but not sure.. I just checked and I think R6 and R5 are not getting their OSPF updates by trying show ip route
Here are my configs: http:[url]....
View 6 Replies
View Related
Jun 22, 2011
I am working at a client site today. The client has a large Frame Relay Hub Spoke network. The Hub is at the HQ location, and then there are about 15 spoke sites in remote offices.
We are having an issue with the frame between the HQ and one of the spokes. We are currently working with our dear friends at AT&T to troubleshoot the issue. AT&T yesterday was trying to run a local loop test to the router at the remote (spoke) end. We were working iwth them in trying to put the remote router (which we manage) into a loopback mode. We were trying to use controller commands
COOP-Rappahanock#conf t
Enter configuration commands, one per line. End with CNTL/Z.
COOP-Rappahanock(config)#controller ?
% Unrecognized command
COOP-Rappahanock(config)#controller
That we seem to run out of options...
How can we put the subinterface that is the other end fo the frame into loopback mode so that a local loop test can be done between us and AT&T (provider)?
View 1 Replies
View Related
May 21, 2011
Main site have 8 departments and each department have 60 pc's,remaining sites each have 6 departments and in each department have 40 pc's and in the design of WAN connection you use frame relays and that is the 100% growng hosptals and clock speed is 64000 bits/sec and security must don't access the unautheraised users from out side....how can I do this?
View 5 Replies
View Related
Nov 10, 2011
Provider T1 handoff with two PVCs to their MPLS cloud to a 2911.One Internet PVC and one for the MPLS including a SIP trunk .
Is there a way to use QOS to have the router prioritize one PVC over the other.Always service the MPLS/SIP PVC over the Internet ONLY PVC?The MPLS/SIP PVC will have QOS for voice but needs to be prioritize.Other option will be to police down the Internet PVC to a value which will leave the required total Kb for the voice priority KB.(FR PIPQ works if the PVC is for voice only.)
View 1 Replies
View Related
Apr 7, 2011
I am having real problems trying to build resiliency into a hub and spoke frame relay scenario. I know the hub is a single point of failure. Is there any way to put some resilience into the network? There is 4 attached branch offices.
View 8 Replies
View Related
Mar 24, 2012
working through a lab and can't seem to configure frame relay on subints. I assume it's not supported but this seems basic; am I doing something wrong?
View 4 Replies
View Related
Sep 21, 2012
I have been trying to make rip work on this frame relay with multipoint configuration (hub and spoke) and I also configured a loopback interface on each of the routers and configured rip with the loopback address. I observed that the routers (cisco 3600 series) are not sending or receiving any RIP updates through their serial interfaces but are sending through loopback interfaces i configured (debug ip rip).I can ping all routers but cant ping their loopback interfaces because RIP updates are not sent or received by them.
R1#debug ip rip
RIP protocol debugging is on
R1#
*Mar 1 00:09:46.759: RIP: sending v2 update to 224.0.0.9 via Loopback1 (1.1.1.1)
*Mar 1 00:09:46.763: RIP: build update entries - suppressing null update
[code]....
View 5 Replies
View Related
Apr 27, 2011
I started studying yesterday for CCNP Route and I'm already stuck. Stupid Frame relay. Basic topology attached, 1 Hub, 2 spokes. I have EIGRP working correctly and each spoke can see all routes correctly. The Hub is on a Multipoint interface with split horizon turned off.
View 15 Replies
View Related
Apr 2, 2012
I've a home lab which consists of three 2610xm routers and I have configured two routers back to back with FR subinterfaces. The commands are used are;
R1
frame relay switching
int s0/0
encap FR
no sh
clock rate 64000
frame-relay intf-type dce
[code].....
Everything works great with this config and I know how to configure without lmi too. My question is more for the CCNA exam and fill the gaps in so to speak. The question is when you configure FR with static mappings and inverse arp do you need actual frame relay switches on the other side of the link or can I configure on my home labs routers. I know I am gonna try and configure this as well, but can I configure multipoint on my third router with a different physical interface. Like R1 with s0/0 to R2 s0/0 and R1 s0/1 to R3 s0/0 with subinterfaces.
View 2 Replies
View Related
Sep 23, 2012
I 'm trying to set up a home lab with a couple of 28XX and 2651XM series routers.I would like to simulate a frame-relay connection between HQ, Branch1 and Branch2 . All of them are conneced to a PSTN switch (2811 router) via T1 cross over cables. The connectivity is like this. [code] I have configured all the routers and FR switch with necessary configuration. However the link between HQ and Branch1 is not coming up. On both the routers I could see the line protocol is down.I have pasted the configuration below.[code]
View 4 Replies
View Related
Dec 14, 2010
As U know cisco feature for frame-relay is creating mfr link and binding them to physical interfaces I did so but my MFR links doesn't get up?
PS. router is ASR1004
frame-relay switching
interface MFR0 description Virtual FR ---> Serial0/0/0 no ip address encapsulation frame-relay IETF frame-relay lmi-type ansi frame-relay intf-type dce frame-relay route 908 interface Serial0/0/0 908!interface MFR1 description Virtual FR ---> Serial0/2/4:0 no ip address encapsulation frame-relay IETF frame-relay lmi-type ansi frame-relay intf-type dce frame-relay route 900 interface Serial0/2/4:0 900
interface Serial0/0/0 (Smart serial interface) description Serial ---> E1 no ip address encapsulation frame-relay MFR1
interface Serial0/2/4:0 (E1 serial interface) description Link ---> S no ip address encapsulation frame-relay MFR0
View 1 Replies
View Related
Jun 14, 2012
I am installing an ASA 5520 and I have a problem on accepring the incoming traffic from an external office connected via Frame Relay.
On my OUTSIDE interface I have both the internet traffic and the external office traffic incoming. What comes from the external office is visible as 10.1.0.0/16.
I have to allow this traffic to enter the internal network, without any control. I would also keep the original IP address.
I have configured the Firewall but I don't know how to setup the NAT.
View 2 Replies
View Related
Dec 18, 2011
IOS 15.1(4)M1.
I am trying to setup my new 2901 running 15.1(4)M1 for frame realy via a VWIC3-1MFT-T1/E1 card. Now I have set up plenty of frame relay connections via older serial cards, but I just cannot find any documentation on how to do this on one of the new VWIC3-1MFT-T1/E1s. None of the commands I am used to seem to even exist. None of the
encapsulation frame-relay ietf
frame-relay interface-dlci 16 ietf
seems to be there. How to configure the card in IOS 15?
View 1 Replies
View Related
Feb 24, 2013
We have frame relay T1 circuit at one of our remote site. Which is connected to our core frame relay router which have DS3 circuit.Now we bought second T1 line at remote site and now I have to configure Bounded T1 with Cisco 1921 router.good config example or document on how to configure frame relay bounded T1 ?
View 1 Replies
View Related
Apr 21, 2009
I have a 3845 running 12.4.13a which I want to upgrade to 12.4.24.After upgrade one of the interface that is configured for frame relay doesn't work anymore.In fact is the "service-module t1 timeslots" commands that can not be executed and the router throws that error.I tested this behaviour on two 3845s and the result is the same.Is this a bug or is an workaround for it?
View 3 Replies
View Related
Sep 26, 2012
Transitioning from 3825 to 3945 (OS is 15.0(1r)M13 c3900-universalk9-mz.SPA.151-4.m4). Turning on FDL on the 3825 was easy but the same command on the 3945 doesn't work.
View 3 Replies
View Related
Jan 22, 2013
I have a NM-1CE1U working on my router 2600 , configured with frame-relay . But seems it does not work on my router 2811. I have check that the replacement is HWIC-1CE1T1-PRI , right ？
But the problem is these two modules have different interface type , I want to keep my cable interface type and find one module card working on 2800 or 2900 router , can configure frame-relay.
View 2 Replies
View Related
Jan 10, 2012
QoS on an MFR interface/subinterfaces. We have a remote site with two bundled T1's terminating on a 2951 router for a total bandwidth of 3072. The circuit is provided by Paetec and the subinterfaces are designated for internet and MPLS traffic respectively. The issue we are facing is with outbound voice quality. It seems that no matter how we apply QoS, either to the main MFR interface or the MFR subinterfaces, voice packets do not seem to be prioritized. We tried FRTS, which slowed the entire link down to a crawl, we tried applying a class map to the main interface as well as a service policy, none of which seemed to affect anything.
class-map match-all VOICE
match ip dscp ef
class-map match-any SIGNALING
match ip dscp af31
match ip dscp cs3 (code)
View 4 Replies
View Related
Jan 27, 2013
I have catalyst 3750 I want to controle traffics on every port I have tried Frame-Relay Traffice shaping and Quality of service but there is no support for these commands in the switch.do we have any way to limit traffic on every port in catalyst 3750 and 2960 switches ?
View 4 Replies
View Related
Nov 13, 2011
I need to get some low volume, interactive data, prioritized on frame relay PVCs across our network. I have followed the CBWFQ examples from cisco.com, but my test packets are still showing latency over 1 second. My lab set up has a corporate connected gateway router linked via FE to testrouter 50. TR51 has a T1 frame relay loop to another router acting as a frame relay switch. The other side of the FR switch has a 56k link to testrouter51. I am sourcing test pings from my desktop PC, that are marked as AF43, and leave at a rate of 1/second, when the response comes back in time. I am using a Smartbits to generate some default class traffic at a rate of about 56Kbps only in the 'outbound' direction, toward TR51, as this emulates a file copy from corporate to remote sites, that is causing the AF43 traffic to suffer. Here is the relevant config on the TR50 device:
class-map match-all rtu-data
match ip dscp af43
!
policy-map frame-56
class rtu-data
priority percent 20
class network-mgt-data
bandwidth percent 5(code)
View 1 Replies
View Related
May 19, 2011
Application is that need to configure the VOIP with the existing Frame relay network ,where VOFR command is not shown in the router when type yhe command router config#dial-peer voice 123 need vofr On the 3945 router where in the router it is not accepting the above command,
View 8 Replies
View Related
Aug 20, 2011
why the WAN protocols like Frame-relay, HDLC and PPP are called Layer2 protocols?What is the address scheme they use?
View 5 Replies
View Related
Feb 28, 2011
i recently bought and installed a working NM-16ESW into my cisco 2610.HOWEVER:i have tried different IOS's:c2600-ik9o3s-mz.122-46a.binc2600-io3-mz.122-46a.binc2600-io3-mz.123-26.bin and unfortunately non of those IOS versions works with the NM-16ESW.Heres my SHOW DIAG command:
Router#show diagSlot 0: C2610 1E Mainboard Port adapter, 3 ports Port adapter is analyzed Port adapter insertion time unknown EEPROM contents at hardware discovery: Hardware Revision : 3.0 PCB Serial Number : JAD05470D9S (1580012177) Part Number : 73-2839-14 RMA History : 00 RMA Number : 0-0-0-0 Board Revision : B0 Deviation Number : 0-0 EEPROM format version 4 EEPROM contents (hex): 0x00: 04 FF 40 00 91 41 03 00 C1 18 4A 41 44 30 35 34 0x10: 37 30 44 39 53 20 28 31 35 38 30 30 31 32 31 37 0x20: 37 29 82 49 0B 17 0E 04 00 81 00 00 00 00 42 42 0x30: 30 80 00 00 00 00 FF FF FF FF FF FF FF FF FF FF 0x40: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[code].....
View 1 Replies
View Related
Apr 5, 2013
I'm just about to update flash on my router 2610, but I don't know which IOS i should take that's specification of my router: [code]
View 6 Replies
View Related
Jan 26, 2012
I am trying to test and setup some ACL's on a switch, the current setup is:
Core Switch - HP ProCurve 2610-24-PWR
Edge Switch - HP ProCurve 2510-24
VLANS 5, 10, 15, 20, 25, 30
I want to deny access to VLAN 5 from VLAN 20 which is are client VLAN.
View 6 Replies
View Related
Sep 18, 2011
I've got three Cisco 1721's and a 2610, two of the 1721's are 32f's, the other one is a bit older but is still the same model. The two Cisco 1721 32f's have 1-dsu-t1-v2 wics in them, and the older 1721 has a 1-dsu-t1 wic in it. Now no matter how i have configured it the old t1 wic will not talk to the v2 wic. I've tried putting the old wic into a 1721 32f and it doesn't work at all!
What i have working:
router DCE (1721 32f with v2 wic) can talk to router DTE (1721 32f with v2 wic) no problem with this configuration.
Router DCE:
-service-module t1 clock source internal
-service-module t1 data-coding normal
[ code].....
Router DTE:
-service-module t1 clock source line
-service-module t1 data-coding normal
[ code]....
Router OLD (1721 with v2 wic) can talk to router DTE (1721 32f with v2 wic) no problem with same config. What doesn't work: Any router with 1-dsu-t1 (old) wic to router DTE (1721 32f with v2 wic). again same configuration as before, so whats going on that i cant get this to work? Is the old t1 wic not compatible with the new t1 wic?
View 4 Replies
View Related
Jan 15, 2011
I erased my flash and cannot locate an IOS that will fit on my 2610 router, I was running 11.3(7), but cannot locate anything even close.
View 3 Replies
View Related
Jan 6, 2012
I have a Cisco 2610 series router(Version 12.0(5)T1, c2600-i-mz.120-5.T1), which has a network module inserted. I would like to view the model of this network module. There are no "show inventory" or "show platform" commands. "Show version" doesn't list the network module as well. In addition, it appears to have a "show c2600" command, but this doesn't display any hardware information.
View 14 Replies
View Related
Apr 28, 2013
I have a home lab. I am trying to connect a 1710 to a 2610 with just using the fast ethernet ports. I understand that serial connections and t1 csu/dsu connections use clocking, etc. How can I configure FA ports to do the same AND be routable?
View 6 Replies
View Related
Mar 2, 2012
I have a Cisoc 2610 connected to my network, 1 Ethernet port and a WIC-2T card. I have ther serial connection to the main router and the ethernet going to the switch. I can ping all device throught the network...but the 2610 can't ping any outside address (no internet connection). I have the internet connection going through my 3745 (which the 2610 is connected to via serial cable). I put a default route into the 2610 but still no luck.
Here are the running configs:
2610:
version 12.3
service timestamps debug uptime
service timestamps log uptime
[Code].....
View 11 Replies
View Related
Nov 16, 2012
I hope I'm posting this in the correct place. I have a 2610 router and on starting it up i get this and only this,
"System Bootstrap, Version 11.3(2)XA4, RELEASE SOFTWARE (fc1)
Copyright (c) 1999 by Cisco Systems, Inc.
TAC:Home:SW:IOS:Specials for info"
thats all and exactly what is displayed on the console screen the device is none responsive.
View 1 Replies
View Related
Mar 3, 2013
I have 2 Procuve Switches one is 2650 were all the Department PC's & Wireless access points connected & second one is 2610 were i have the firewall connected,Active Directory & Windows DHCP Server
Switch 1- 2650
Ports
Port 1-16 is used by HR Department
Port17-32 is used by Finanace Department
Port 33-34 is used by Access Points
Port 41-48 is used by Users
Port 50 is used to uplink to switch 2610.What i wanted to achive is Isolcate Departments & Users & Access Points through VLAN from each other but they should be able to hit our Active directory for authentication, Firewall for internet & DHCP Server for IP's.
View 3 Replies
View Related
