Why WAN Protocols Like Frame-relay / HDLC And PPP Are Called Layer2 Protocols
Aug 20, 2011why the WAN protocols like Frame-relay, HDLC and PPP are called Layer2 protocols?What is the address scheme they use?
View 5 Replies
ADVERTISEMENT
Cisco :: Frame Frame Relay / OSP - Ping 1 Way But Not The Other?
Apr 23, 2013Network is 10.254.0.0/16
snag.gy/3Y8aN.jpg This is the network image.
This is my subnetted connections: http:[url]....
I can ping R2 to R5 but not R5 to R2. I have spent about 10 hours going through my network and code to no avail. I think it is the frame relay that's causing the error but not sure.. I just checked and I think R6 and R5 are not getting their OSPF updates by trying show ip route
Here are my configs: http:[url]....
WAN Setup Using Frame Relay?
May 21, 2011Main site have 8 departments and each department have 60 pc's,remaining sites each have 6 departments and in each department have 40 pc's and in the design of WAN connection you use frame relays and that is the 100% growng hosptals and clock speed is 64000 bits/sec and security must don't access the unautheraised users from out side....how can I do this?
View 5 Replies View RelatedFrame Relay Hub And Spoke Resiliency?
Apr 7, 2011I am having real problems trying to build resiliency into a hub and spoke frame relay scenario. I know the hub is a single point of failure. Is there any way to put some resilience into the network? There is 4 attached branch offices.
View 8 Replies View RelatedCisco WAN :: 2911 Qos On Frame Relay
Nov 10, 2011Provider T1 handoff with two PVCs to their MPLS cloud to a 2911.One Internet PVC and one for the MPLS including a SIP trunk .
Is there a way to use QOS to have the router prioritize one PVC over the other.Always service the MPLS/SIP PVC over the Internet ONLY PVC?The MPLS/SIP PVC will have QOS for voice but needs to be prioritize.Other option will be to police down the Internet PVC to a value which will leave the required total Kb for the voice priority KB.(FR PIPQ works if the PVC is for voice only.)
Cisco :: Frame Relay On Sub-Interfaces Not Supported?
Mar 24, 2012working through a lab and can't seem to configure frame relay on subints. I assume it's not supported but this seems basic; am I doing something wrong?
View 4 Replies View RelatedCisco :: RIP Over Frame Relay Multipoint Configuration?
Sep 21, 2012I have been trying to make rip work on this frame relay with multipoint configuration (hub and spoke) and I also configured a loopback interface on each of the routers and configured rip with the loopback address. I observed that the routers (cisco 3600 series) are not sending or receiving any RIP updates through their serial interfaces but are sending through loopback interfaces i configured (debug ip rip).I can ping all routers but cant ping their loopback interfaces because RIP updates are not sent or received by them.
R1#debug ip rip
RIP protocol debugging is on
R1#
*Mar 1 00:09:46.759: RIP: sending v2 update to 224.0.0.9 via Loopback1 (1.1.1.1)
*Mar 1 00:09:46.763: RIP: build update entries - suppressing null update
[code]....
Cisco :: EIGRP NBMA Frame Relay
Apr 27, 2011I started studying yesterday for CCNP Route and I'm already stuck. Stupid Frame relay. Basic topology attached, 1 Hub, 2 spokes. I have EIGRP working correctly and each spoke can see all routes correctly. The Hub is on a Multipoint interface with split horizon turned off.
View 15 Replies View RelatedCisco WAN :: 2610xm / Frame Relay Inverse Arp
Apr 2, 2012I've a home lab which consists of three 2610xm routers and I have configured two routers back to back with FR subinterfaces. The commands are used are;
R1
frame relay switching
int s0/0
encap FR
no sh
clock rate 64000
frame-relay intf-type dce
[code].....
Everything works great with this config and I know how to configure without lmi too. My question is more for the CCNA exam and fill the gaps in so to speak. The question is when you configure FR with static mappings and inverse arp do you need actual frame relay switches on the other side of the link or can I configure on my home labs routers. I know I am gonna try and configure this as well, but can I configure multipoint on my third router with a different physical interface. Like R1 with s0/0 to R2 s0/0 and R1 s0/1 to R3 s0/0 with subinterfaces.
Cisco WAN :: 2651XM Frame-relay Interface Not Coming Up
Sep 23, 2012I 'm trying to set up a home lab with a couple of 28XX and 2651XM series routers.I would like to simulate a frame-relay connection between HQ, Branch1 and Branch2 . All of them are conneced to a PSTN switch (2811 router) via T1 cross over cables. The connectivity is like this. [code] I have configured all the routers and FR switch with necessary configuration. However the link between HQ and Branch1 is not coming up. On both the routers I could see the line protocol is down.I have pasted the configuration below.[code]
View 4 Replies View RelatedCisco WAN :: ASR1004 Multi Frame-Relay Switching?
Dec 14, 2010As U know cisco feature for frame-relay is creating mfr link and binding them to physical interfaces I did so but my MFR links doesn't get up?
PS. router is ASR1004
frame-relay switching
interface MFR0 description Virtual FR ---> Serial0/0/0 no ip address encapsulation frame-relay IETF frame-relay lmi-type ansi frame-relay intf-type dce frame-relay route 908 interface Serial0/0/0 908!interface MFR1 description Virtual FR ---> Serial0/2/4:0 no ip address encapsulation frame-relay IETF frame-relay lmi-type ansi frame-relay intf-type dce frame-relay route 900 interface Serial0/2/4:0 900
interface Serial0/0/0 (Smart serial interface) description Serial ---> E1 no ip address encapsulation frame-relay MFR1
interface Serial0/2/4:0 (E1 serial interface) description Link ---> S no ip address encapsulation frame-relay MFR0
Cisco Firewall :: ASA 5520 - Allow All Traffic From Frame Relay
Jun 14, 2012I am installing an ASA 5520 and I have a problem on accepring the incoming traffic from an external office connected via Frame Relay.
On my OUTSIDE interface I have both the internet traffic and the external office traffic incoming. What comes from the external office is visible as 10.1.0.0/16.
I have to allow this traffic to enter the internal network, without any control. I would also keep the original IP address.
I have configured the Firewall but I don't know how to setup the NAT.
Cisco WAN :: 2610 Testing Out Frame Relay Connections
Mar 13, 2012I'm looking to test fram relay connections in a lab environment i'm building at home. I have a couple of 2610 routers that are barebones and am looking to get some serial modules. Are (2) WIC-2T's all I would need to create those test connections? Also on a side note are the any modules for the 2610 that have fast ethernet connections. I would like to have that so I can create a router on a stick model off of the 2600's.
View 1 Replies View RelatedCisco WAN :: C2901 VWIC3-1MFT-T1 / E1 Frame Relay?
Dec 18, 2011IOS 15.1(4)M1.
I am trying to setup my new 2901 running 15.1(4)M1 for frame realy via a VWIC3-1MFT-T1/E1 card. Now I have set up plenty of frame relay connections via older serial cards, but I just cannot find any documentation on how to do this on one of the new VWIC3-1MFT-T1/E1s. None of the commands I am used to seem to even exist. None of the
encapsulation frame-relay ietf
frame-relay interface-dlci 16 ietf
seems to be there. How to configure the card in IOS 15?
Cisco WAN :: 1921 Frame Relay Bounded T1 Configuration
Feb 24, 2013We have frame relay T1 circuit at one of our remote site. Which is connected to our core frame relay router which have DS3 circuit.Now we bought second T1 line at remote site and now I have to configure Bounded T1 with Cisco 1921 router.good config example or document on how to configure frame relay bounded T1 ?
View 1 Replies View RelatedCisco WAN :: 3845 Frame Relay Doesn't Work Anymore
Apr 21, 2009I have a 3845 running 12.4.13a which I want to upgrade to 12.4.24.After upgrade one of the interface that is configured for frame relay doesn't work anymore.In fact is the "service-module t1 timeslots" commands that can not be executed and the router throws that error.I tested this behaviour on two 3845s and the result is the same.Is this a bug or is an workaround for it?
View 3 Replies View RelatedCisco Infrastructure :: Frame Relay FDL Command For 3900 Router T1?
Sep 26, 2012Transitioning from 3825 to 3945 (OS is 15.0(1r)M13 c3900-universalk9-mz.SPA.151-4.m4). Turning on FDL on the 3825 was easy but the same command on the 3945 doesn't work.
View 3 Replies View RelatedCisco WAN :: NM-1CE1U Working On Router 2600 / Configured With Frame-relay
Jan 22, 2013I have a NM-1CE1U working on my router 2600 , configured with frame-relay . But seems it does not work on my router 2811. I have check that the replacement is HWIC-1CE1T1-PRI , right ？
But the problem is these two modules have different interface type , I want to keep my cable interface type and find one module card working on 2800 or 2900 router , can configure frame-relay.
Cisco WAN :: 2951 - QoS For Voice On Multi-Link Frame Relay Interface / Subinterface
Jan 10, 2012QoS on an MFR interface/subinterfaces. We have a remote site with two bundled T1's terminating on a 2951 router for a total bandwidth of 3072. The circuit is provided by Paetec and the subinterfaces are designated for internet and MPLS traffic respectively. The issue we are facing is with outbound voice quality. It seems that no matter how we apply QoS, either to the main MFR interface or the MFR subinterfaces, voice packets do not seem to be prioritized. We tried FRTS, which slowed the entire link down to a crawl, we tried applying a class map to the main interface as well as a service policy, none of which seemed to affect anything.
class-map match-all VOICE
match ip dscp ef
class-map match-any SIGNALING
match ip dscp af31
match ip dscp cs3 (code)
Cisco Switching/Routing :: Catalyst 3750 Frame-Relay Traffic Shaping Not Supported?
Jan 27, 2013I have catalyst 3750 I want to controle traffics on every port I have tried Frame-Relay Traffice shaping and Quality of service but there is no support for these commands in the switch.do we have any way to limit traffic on every port in catalyst 3750 and 2960 switches ?
View 4 Replies View RelatedCisco Switching/Routing :: TR50 - Priority Queuing Of Packets On Frame Relay Subinterface
Nov 13, 2011I need to get some low volume, interactive data, prioritized on frame relay PVCs across our network. I have followed the CBWFQ examples from cisco.com, but my test packets are still showing latency over 1 second. My lab set up has a corporate connected gateway router linked via FE to testrouter 50. TR51 has a T1 frame relay loop to another router acting as a frame relay switch. The other side of the FR switch has a 56k link to testrouter51. I am sourcing test pings from my desktop PC, that are marked as AF43, and leave at a rate of 1/second, when the response comes back in time. I am using a Smartbits to generate some default class traffic at a rate of about 56Kbps only in the 'outbound' direction, toward TR51, as this emulates a file copy from corporate to remote sites, that is causing the AF43 traffic to suffer. Here is the relevant config on the TR50 device:
class-map match-all rtu-data
match ip dscp af43
!
policy-map frame-56
class rtu-data
priority percent 20
class network-mgt-data
bandwidth percent 5(code)
Cisco WAN :: 3945 To 7206 Router Via IGX 8400 / Configure VoIP With Existing Frame Relay Network
May 19, 2011Application is that need to configure the VOIP with the existing Frame relay network ,where VOFR command is not shown in the router when type yhe command router config#dial-peer voice 123 need vofr On the 3945 router where in the router it is not accepting the above command,
View 8 Replies View RelatedRouting Protocols Cannot Communicate Together
Sep 5, 2011I have an skill exercise with 4 Routing Protocols Default Route,Static Route,Eigrp, Ospf. I have about 6-7 routers, and each of them has an routing protocol. But the problem is the Main router INTERNET, which it has to use Static in a direction, and default in the opposite path. This is the scheme of routers and how the r.protocol have to be configured.
View 19 Replies View RelatedWay To Disable Network Protocols
Apr 11, 2013Do i need these protocols and can i disable or uninstall them?
QoS Packet Scheduler
File and Printer Sharing for Microsoft Networks
Client for Microsoft Networks
Finding The Headers Of Different Protocols?
Mar 3, 2012I need to find the headers of different protocols like ETH_IP, ETH_IPv6_IP, ETH_MPLS_IP, ETH_VLAN_IP , ETH_MPLS_ETH_IP , ETH_MPLS_MPLS_IP, PPPC_IP_TCPnUDP and many more.
I dnt know how to find. some one told me about wireshark , i installed that software and started capturing the packets but didnt find any of above except ip.
Protocols :: Can't Connect Router To PC
Jun 20, 2011I have a Dell Inspiron 1501 with updated windows XP. Today I purchased a netgear wireless router N150 and a roku player. I inserted set-up CD after I hooked up cables to computer, modem and router. The message told me that there was no ethernet adapter and spelled the end to my installation.
View 1 Replies View RelatedProtocols / Routing :: Can't Go On Websites
Feb 26, 2011The websites I usually go on now have some type of error page when I go to them. So far it has happened to 2 of them though they might not be related.
Here's what the page says:
Site 1- Valenth
Quote:
Warning: mysql_connect() [ function.mysql-connect]: [2002] Connection timed out (trying to connect via tcp://ec2-184-73-84-14.compute-1.amazonaws.com:3306) in /var/www/valenth.com/include/database.class.php on line 25
[Code]....
Protocols / Routing :: Webpage Not Available?
Sep 4, 2012i've had this internet problem that has been going on with a wireless laptop i've had since april. it only happens on this computer, and i've tried many solutions. occasionally, i will try and go to pages on google chrome and an error pops up that says "this webpage is not available." when i play games that are online, they get disconnected as well. i've added google chrome and my other browsers to the firewall list and i've also changed the DNS server. when i use the troubleshooter it says something like "router, or modem is not connected to the internet. i've even downloaded the "fix it" program and it detected no problems
View 1 Replies View RelatedProtocols / Routing :: Can't Get RDP To Work
Jun 1, 2011I can't get RDP to work on a specific computer.I've already set it up on the router, know the IP address, and I can get it to work great with the server, but the workstation we want it to go to won't accept it.I checked, it's set to allow RDP, the firewall exception was setup, also turned off the firewall completely, removed the antivirus software, checked TCP/IP filtering on the lan connection, even changed the listening port and still nothing.
View 9 Replies View RelatedProtocols / Routing :: IP Conflict Through LAN
Jan 4, 2012Problem with a conflicting IP address. Basically on a normal running day my wireless is switched on and connected perfect to my internet, however if i want to download any large files i plug my Ethernet to my laptop and disable the wireless from my laptop, instantly then the LAN connection kicks in and im on the internet again as i find download speeds are faster through a LAN. However today my wireless is fine but the second i switch to LAN the ! symbol appears and a message says their is an IP conflict.
View 2 Replies View RelatedProtocols / Routing :: Unable To Use FTP
Aug 17, 2011I've been timing out via any FTP client, including FileZilla, FireFTP, and a few others. I even downloaded a few just to see if I could connect with other clients.I contacted my host who can't recreate the issue on their end. I contacted my ISP who instructed me to use my command prompt in order to connect to their server, and that of mozilla. Both times I was able to connect via the command prompt.I don't understand what's going on.If I can connect to the sample sites that my ISP gave me, why can't I connect using an FTP client any longer. What possible change could have been made to have caused that disconnection that happened a few nights ago, and is now causing the timeouts I continue to receive?
View 6 Replies View RelatedProtocols / Routing :: How To Change My Ip
Apr 12, 2011How can i actually change my ip...tryed those cmd things but nothing works. Ineed to change ip somehow.
View 1 Replies View RelatedDo These Protocols Match Correctly To Each Layer?
Apr 17, 2011Data link-ARP,RARP, presentation-SSL,TSL,ASCII,JPG, Session layer-ASP(apple talk session protocol),SCP are these correct?can your provide 2 new protocols for each with the long name?
View 17 Replies View Related