We have frame relay T1 circuit at one of our remote site. Which is connected to our core frame relay router which have DS3 circuit.Now we bought second T1 line at remote site and now I have to configure Bounded T1 with Cisco 1921 router.good config example or document on how to configure frame relay bounded T1 ?
View 1 RepliesI have been trying to make rip work on this frame relay with multipoint configuration (hub and spoke) and I also configured a loopback interface on each of the routers and configured rip with the loopback address. I observed that the routers (cisco 3600 series) are not sending or receiving any RIP updates through their serial interfaces but are sending through loopback interfaces i configured (debug ip rip).I can ping all routers but cant ping their loopback interfaces because RIP updates are not sent or received by them.
R1#debug ip rip
RIP protocol debugging is on
R1#
*Mar 1 00:09:46.759: RIP: sending v2 update to 224.0.0.9 via Loopback1 (1.1.1.1)
*Mar 1 00:09:46.763: RIP: build update entries - suppressing null update
[code]....
Network is 10.254.0.0/16
snag.gy/3Y8aN.jpg This is the network image.
This is my subnetted connections: http:[url]....
I can ping R2 to R5 but not R5 to R2. I have spent about 10 hours going through my network and code to no avail. I think it is the frame relay that's causing the error but not sure.. I just checked and I think R6 and R5 are not getting their OSPF updates by trying show ip route
Here are my configs: http:[url]....
Main site have 8 departments and each department have 60 pc's,remaining sites each have 6 departments and in each department have 40 pc's and in the design of WAN connection you use frame relays and that is the 100% growng hosptals and clock speed is 64000 bits/sec and security must don't access the unautheraised users from out side....how can I do this?
View 5 Replies View RelatedProvider T1 handoff with two PVCs to their MPLS cloud to a 2911.One Internet PVC and one for the MPLS including a SIP trunk .
Is there a way to use QOS to have the router prioritize one PVC over the other.Always service the MPLS/SIP PVC over the Internet ONLY PVC?The MPLS/SIP PVC will have QOS for voice but needs to be prioritize.Other option will be to police down the Internet PVC to a value which will leave the required total Kb for the voice priority KB.(FR PIPQ works if the PVC is for voice only.)
I am having real problems trying to build resiliency into a hub and spoke frame relay scenario. I know the hub is a single point of failure. Is there any way to put some resilience into the network? There is 4 attached branch offices.
View 8 Replies View Relatedworking through a lab and can't seem to configure frame relay on subints. I assume it's not supported but this seems basic; am I doing something wrong?
View 4 Replies View RelatedI started studying yesterday for CCNP Route and I'm already stuck. Stupid Frame relay. Basic topology attached, 1 Hub, 2 spokes. I have EIGRP working correctly and each spoke can see all routes correctly. The Hub is on a Multipoint interface with split horizon turned off.
View 15 Replies View RelatedI've a home lab which consists of three 2610xm routers and I have configured two routers back to back with FR subinterfaces. The commands are used are;
R1
frame relay switching
int s0/0
encap FR
no sh
clock rate 64000
frame-relay intf-type dce
[code].....
Everything works great with this config and I know how to configure without lmi too. My question is more for the CCNA exam and fill the gaps in so to speak. The question is when you configure FR with static mappings and inverse arp do you need actual frame relay switches on the other side of the link or can I configure on my home labs routers. I know I am gonna try and configure this as well, but can I configure multipoint on my third router with a different physical interface. Like R1 with s0/0 to R2 s0/0 and R1 s0/1 to R3 s0/0 with subinterfaces.
I 'm trying to set up a home lab with a couple of 28XX and 2651XM series routers.I would like to simulate a frame-relay connection between HQ, Branch1 and Branch2 . All of them are conneced to a PSTN switch (2811 router) via T1 cross over cables. The connectivity is like this. [code] I have configured all the routers and FR switch with necessary configuration. However the link between HQ and Branch1 is not coming up. On both the routers I could see the line protocol is down.I have pasted the configuration below.[code]
View 4 Replies View RelatedAs U know cisco feature for frame-relay is creating mfr link and binding them to physical interfaces I did so but my MFR links doesn't get up?
PS. router is ASR1004
frame-relay switching
interface MFR0 description Virtual FR ---> Serial0/0/0 no ip address encapsulation frame-relay IETF frame-relay lmi-type ansi frame-relay intf-type dce frame-relay route 908 interface Serial0/0/0 908!interface MFR1 description Virtual FR ---> Serial0/2/4:0 no ip address encapsulation frame-relay IETF frame-relay lmi-type ansi frame-relay intf-type dce frame-relay route 900 interface Serial0/2/4:0 900
interface Serial0/0/0 (Smart serial interface) description Serial ---> E1 no ip address encapsulation frame-relay MFR1
interface Serial0/2/4:0 (E1 serial interface) description Link ---> S no ip address encapsulation frame-relay MFR0
I am installing an ASA 5520 and I have a problem on accepring the incoming traffic from an external office connected via Frame Relay.
On my OUTSIDE interface I have both the internet traffic and the external office traffic incoming. What comes from the external office is visible as 10.1.0.0/16.
I have to allow this traffic to enter the internal network, without any control. I would also keep the original IP address.
I have configured the Firewall but I don't know how to setup the NAT.
I'm looking to test fram relay connections in a lab environment i'm building at home. I have a couple of 2610 routers that are barebones and am looking to get some serial modules. Are (2) WIC-2T's all I would need to create those test connections? Also on a side note are the any modules for the 2610 that have fast ethernet connections. I would like to have that so I can create a router on a stick model off of the 2600's.
View 1 Replies View RelatedIOS 15.1(4)M1.
I am trying to setup my new 2901 running 15.1(4)M1 for frame realy via a VWIC3-1MFT-T1/E1 card. Now I have set up plenty of frame relay connections via older serial cards, but I just cannot find any documentation on how to do this on one of the new VWIC3-1MFT-T1/E1s. None of the commands I am used to seem to even exist. None of the
encapsulation frame-relay ietf
frame-relay interface-dlci 16 ietf
seems to be there. How to configure the card in IOS 15?
I have a 3845 running 12.4.13a which I want to upgrade to 12.4.24.After upgrade one of the interface that is configured for frame relay doesn't work anymore.In fact is the "service-module t1 timeslots" commands that can not be executed and the router throws that error.I tested this behaviour on two 3845s and the result is the same.Is this a bug or is an workaround for it?
View 3 Replies View RelatedTransitioning from 3825 to 3945 (OS is 15.0(1r)M13 c3900-universalk9-mz.SPA.151-4.m4). Turning on FDL on the 3825 was easy but the same command on the 3945 doesn't work.
View 3 Replies View RelatedI have a NM-1CE1U working on my router 2600 , configured with frame-relay . But seems it does not work on my router 2811. I have check that the replacement is HWIC-1CE1T1-PRI , right ？
But the problem is these two modules have different interface type , I want to keep my cable interface type and find one module card working on 2800 or 2900 router , can configure frame-relay.
QoS on an MFR interface/subinterfaces. We have a remote site with two bundled T1's terminating on a 2951 router for a total bandwidth of 3072. The circuit is provided by Paetec and the subinterfaces are designated for internet and MPLS traffic respectively. The issue we are facing is with outbound voice quality. It seems that no matter how we apply QoS, either to the main MFR interface or the MFR subinterfaces, voice packets do not seem to be prioritized. We tried FRTS, which slowed the entire link down to a crawl, we tried applying a class map to the main interface as well as a service policy, none of which seemed to affect anything.
class-map match-all VOICE
match ip dscp ef
class-map match-any SIGNALING
match ip dscp af31
match ip dscp cs3 (code)
I have catalyst 3750 I want to controle traffics on every port I have tried Frame-Relay Traffice shaping and Quality of service but there is no support for these commands in the switch.do we have any way to limit traffic on every port in catalyst 3750 and 2960 switches ?
View 4 Replies View RelatedI need to get some low volume, interactive data, prioritized on frame relay PVCs across our network. I have followed the CBWFQ examples from cisco.com, but my test packets are still showing latency over 1 second. My lab set up has a corporate connected gateway router linked via FE to testrouter 50. TR51 has a T1 frame relay loop to another router acting as a frame relay switch. The other side of the FR switch has a 56k link to testrouter51. I am sourcing test pings from my desktop PC, that are marked as AF43, and leave at a rate of 1/second, when the response comes back in time. I am using a Smartbits to generate some default class traffic at a rate of about 56Kbps only in the 'outbound' direction, toward TR51, as this emulates a file copy from corporate to remote sites, that is causing the AF43 traffic to suffer. Here is the relevant config on the TR50 device:
class-map match-all rtu-data
match ip dscp af43
!
policy-map frame-56
class rtu-data
priority percent 20
class network-mgt-data
bandwidth percent 5(code)
Application is that need to configure the VOIP with the existing Frame relay network ,where VOFR command is not shown in the router when type yhe command router config#dial-peer voice 123 need vofr On the 3945 router where in the router it is not accepting the above command,
View 8 Replies View Relatedwhy the WAN protocols like Frame-relay, HDLC and PPP are called Layer2 protocols?What is the address scheme they use?
View 5 Replies View RelatedHere is a copy of my cisco 881 easy vpn config. What I need to modify so this will work on a cisco 1921.
hostname BTLvpn
boot-start-markerboot system flash:c870-advipservicesk9-mz.124-11.T3.binboot-end-marker
no logging bufferedenable secret 5 XXXXXX
no aaa new-modelclock timezone EASTERN -5
crypto pki trustpoint TP-self-signed-733417695enrollment selfsignedsubject-name cn=IOS-Self-Signed-Certificate-733417695revocation-check nonersakeypair TP-self-signed-733417695
crypto pki certificate chain TP-self-signed-733417695certificate self-signed 01 30820244 308201AD A0030201(code)
I'm having a problem when configuring this cisco router 1921 with an ip base software. Accordingly with the Cisco software adviser this software allows to configure the l2tp Client Initiated Tunneling. But configuring the router the commands are not recognized:
Router(config)#pseudo wire-class L2TP_PSEUDO
^
% Invalid input detected at '^' marker.
Router(config)#interface Virtual-PPP1.
Since Cisco 2511 is out of sale now and Cisco 1900 series are recommended to replace for the purpose of terminal/comm server. How to configure terminal server on HWIC-8A module?
View 3 Replies View RelatedI have a Cisco 1921 in place with the security IOS so it is also acting as a firewall.
I am wondering if I can enable the GUI so I can configure it remotely.
I have to open several ports from the WAN to LAN on a 1921:
For example:
Say I need port 41795 both UDP and TCP to go from the WAN to the LAN, can some provide me the context I have to follow?
Currently I have this in place
Another piece of this is that the devices that will need to be accessed remotely are on VLAN10 - will that cause a problem?
is installed at a clients home for a very complex Crestron network that included 5 Cisco POE GB switches, 2 VLANS, with VLAN10 utilizing QOS and is the AV network (VLAN1 is the computer network), 8 1142 WAP's, and this 1921.
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2011.12.16 19:52:41 =~=~=~=~=~=~=~=~=~=~=~=show runBuilding configuration...
Current configuration : 3340 bytes!! No configuration change since last restartversion 15.1service timestamps debug datetime msecservice timestamps log datetime msecno service password-encryption!hostname DHOWE_Router!boot-start-markerboot-end-marker!!enable secret 5 $1$JuTn$zn6CnXIm1bJGgPhtRCfB0.enable password ********!no aaa new-model!!no ipv6 cefip source-routeip cef!!ip dhcp excluded-address 192.168.39.0 192.168.39.49ip
[Code] ........
I have recently configured a cisco 1921 router for internal routing on my network. Here is what i am trying to accomplish:
Main network 10.65.1.0 mask 255.255.255.0- all office devies and computers.
Second network 10.65.2.0 mask 255.255.255.0 - All plant equipment machinery and production lines
i have configure gig 0/0 for my company network and gig 0/1 for my plant network. I can ping the router from both networks but am unable to route traffic betwenn them. what am i missing?
sample configuration for internet failover . i have 2 ISPs with one coming in thought a serial cable and another through internet and would wish one take over after the other has failed .The router is Cisco 1921 .
View 4 Replies View RelatedI've recently received this new Cisco 1921 routers with Cisco CP loaded, so it comes up with the annoying change username and password at first access. I've removed all of those files from the flash memory, and rebooted it, and it came up with the proper initial configuration dialog, which is what I wanted. But, whenever I configure the router with a set of basic configuration, like interface, routing, and snmp loggings, and hit wr mem, it doesn't display at all when I do "sh run". It's weird cause when I do sh run | sec rip or any other stuff that I have configured, it shows up , but not in sh run at all.
What's the deal with the new routers? Even sh version doesn't show the config-register or memory allocation details.
xxxxx#sh ver
Cisco IOS Software, C1900 Software (C1900-UNIVERSALK9-M), Version 15.1(4)M4, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
[Code].....
i'm having some trouble setting up the correct NAT configuration of a Cisco 1921 router. The NAT is not working as I want - I think my configuration is wrong somewhere. All clients in 172.16.0.0/24 have the correct outgoing address of 1.1.1.3. But the NAT for 10.10.0.4 (and 10.10.0.5, 10.10.0.6) is partially broken: Ping and ssh from the outside world to 1.1.1.4 is "natted" to 10.10.0.4 and works as expected. But from inside (172.16.0.0/24) ssh to 1.1.1.4 should be "natted" to 10.10.0.4, but doesn't work (ping works). ssh from 172.16.0.0/24 to 10.10.0.4 (without doing NAT) works.
network design:
===============
172.16.0.0/16: network for normal use
192.168.64.0/24: network for specific clients and servers
[Code].....
This is IOS 15.1(4)M3 on a 1921 router. The LAN is 192.168.42.1/24. (DHCP config is further down.) We have a small range that we want to assign via DHCP to devices; .200 through .220 . At the same time, we have a handful of Macintosh systems to which we want to assign a specific address that is not in that 200-220 range. I don't want to configure the assignment based on the Ethernet MAC addresses because these systems might connect via UTP or wireless; that is to say, they have more than one MAC address. They only ever connect using one interface/MAC address at a time, but it's their choice; in some areas wi-fi is available, and in some areas they have to cable-up.
The Mac OSX network settings has a field for "DHCP Client ID". It would be much easier to tell the users of these systems to put their Mac's name in the Client ID field for both their wired and wireless DHCP configs. (As opposed to having them all lookup, and then give me their Ethernet MAC addresses for both of their interfaces.) I tried this with my Mac's (named "shrike") wi-fi interface, but I don't get the 192.168.42.14 address that I expected. I get an address from the .200 to .220 range.
Here's the DHCP-related config from the router:
router#sh run | s dhcp
ip dhcp excluded-address 192.168.42.1 192.168.42.199
ip dhcp excluded-address 192.168.42.221 192.168.42.254
ip dhcp pool OurOffice
network 192.168.42.0 255.255.255.0
[code]....
Is "client-name" the wrong place to configure the DHCP Client ID?
We want to puchase new Cisco ISR 1921/K9 . i want to know does it support the following sample IP-SLA commands
ip sla 2icmp-echo 172.16.1.2timeout 500frequency 1ip sla schedule 2 life forever start-time now
track 10 rtr 1 reachability
delay down 1 up 1
!
track 20 rtr 2 reachability
delay down 1 up 1
ip route 0.0.0.0 0.0.0.0 192.168.1.2 track 10ip route 0.0.0.0 0.0.0.0 172.16.1.2 track 20
Im asking above question because we will need to enable ip-sla on the mentioned router. as i read on the cisco webside, it says Cisco-ISR-1921/K9-IP Base support only IP-SLA RESPONDER feature nothing else. If Cisco-921/K9 does not support the above commands , should i go for ordering Cisco-1921-SEC/K9 ?