I'm having a problem when configuring this cisco router 1921 with an ip base software. Accordingly with the Cisco software adviser this software allows to configure the l2tp Client Initiated Tunneling. But configuring the router the commands are not recognized:
Router(config)#pseudo wire-class L2TP_PSEUDO
^
% Invalid input detected at '^' marker.
Router(config)#interface Virtual-PPP1.
I am working up a configuration template for an install I am doing in a couple weeks and wanted to take a look at the base config of an ASR1002.
View 1 Replies View RelatedMy ASA 5505 base license allows for three VLANs, the third one can only initiate traffic to one other VLAN (as specified by no forward interface vlan <number> on the third VLAN). This doesn't mean it can't "access" the other VLAN, it just can't initiate traffic to it. A lot of people get that wrong.Let's say you've got three VLANs, one is OUTSIDE, two is DMZ, and three is INSIDE. On the second VLAN would I enter the no forward interface as vlan 3, then set the name via the nameif command and everything will work just fine. The DMZ will not be able to initiate traffic to the INSIDE, but will to the outside, and assuming you have your ACLs and NAT set up properly, it will be able to respond to traffic from the INSIDE.
Would that be best practice or would I enter the "no forward" interface as in VLAN 1, thus is being able to respond to traffic from the outside as opposed to the inside.
I had a DMZ set up but since there was an intrusion into my network, I am building it again.
Need basic wireless configuration for a SOHO Cisco 1811W router? I just need the wireless to connect to the base wired LAN - with both WEP and MAC authentication. And - can the MAC auth. parameters be configured via CLI and not have to use either SDM or CP? I can access the router via SDM - but the Wirless Application will not fire up - and CP doesn't work at all.
View 18 Replies View Relatedconfigure the Firewall ASA 5510 in context based configuration in HA Mode with two different subnet....
IP Details are below.....:
interface Ethernet0/0
nameif outside
security-level 0
[Code].....
During high throughput times (nightly, when backup runs) we see packet drops on the network. We think it's the ACE module that drops. We use 2 ACE 20-MOD-K9 with base licenses in a FT configuration in Layer2 Mode.Now I found an interesting statistic on the ACE: [code] How to reset this counter?
View 4 Replies View RelatedHere is a copy of my cisco 881 easy vpn config. What I need to modify so this will work on a cisco 1921.
hostname BTLvpn
boot-start-markerboot system flash:c870-advipservicesk9-mz.124-11.T3.binboot-end-marker
no logging bufferedenable secret 5 XXXXXX
no aaa new-modelclock timezone EASTERN -5
crypto pki trustpoint TP-self-signed-733417695enrollment selfsignedsubject-name cn=IOS-Self-Signed-Certificate-733417695revocation-check nonersakeypair TP-self-signed-733417695
crypto pki certificate chain TP-self-signed-733417695certificate self-signed 01 30820244 308201AD A0030201(code)
Since Cisco 2511 is out of sale now and Cisco 1900 series are recommended to replace for the purpose of terminal/comm server. How to configure terminal server on HWIC-8A module?
View 3 Replies View RelatedI have a Cisco 1921 in place with the security IOS so it is also acting as a firewall.
I am wondering if I can enable the GUI so I can configure it remotely.
I have to open several ports from the WAN to LAN on a 1921:
For example:
Say I need port 41795 both UDP and TCP to go from the WAN to the LAN, can some provide me the context I have to follow?
Currently I have this in place
Another piece of this is that the devices that will need to be accessed remotely are on VLAN10 - will that cause a problem?
is installed at a clients home for a very complex Crestron network that included 5 Cisco POE GB switches, 2 VLANS, with VLAN10 utilizing QOS and is the AV network (VLAN1 is the computer network), 8 1142 WAP's, and this 1921.
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2011.12.16 19:52:41 =~=~=~=~=~=~=~=~=~=~=~=show runBuilding configuration...
Current configuration : 3340 bytes!! No configuration change since last restartversion 15.1service timestamps debug datetime msecservice timestamps log datetime msecno service password-encryption!hostname DHOWE_Router!boot-start-markerboot-end-marker!!enable secret 5 $1$JuTn$zn6CnXIm1bJGgPhtRCfB0.enable password ********!no aaa new-model!!no ipv6 cefip source-routeip cef!!ip dhcp excluded-address 192.168.39.0 192.168.39.49ip
[Code] ........
I have recently configured a cisco 1921 router for internal routing on my network. Here is what i am trying to accomplish:
Main network 10.65.1.0 mask 255.255.255.0- all office devies and computers.
Second network 10.65.2.0 mask 255.255.255.0 - All plant equipment machinery and production lines
i have configure gig 0/0 for my company network and gig 0/1 for my plant network. I can ping the router from both networks but am unable to route traffic betwenn them. what am i missing?
sample configuration for internet failover . i have 2 ISPs with one coming in thought a serial cable and another through internet and would wish one take over after the other has failed .The router is Cisco 1921 .
View 4 Replies View RelatedI've recently received this new Cisco 1921 routers with Cisco CP loaded, so it comes up with the annoying change username and password at first access. I've removed all of those files from the flash memory, and rebooted it, and it came up with the proper initial configuration dialog, which is what I wanted. But, whenever I configure the router with a set of basic configuration, like interface, routing, and snmp loggings, and hit wr mem, it doesn't display at all when I do "sh run". It's weird cause when I do sh run | sec rip or any other stuff that I have configured, it shows up , but not in sh run at all.
What's the deal with the new routers? Even sh version doesn't show the config-register or memory allocation details.
xxxxx#sh ver
Cisco IOS Software, C1900 Software (C1900-UNIVERSALK9-M), Version 15.1(4)M4, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
[Code].....
We have frame relay T1 circuit at one of our remote site. Which is connected to our core frame relay router which have DS3 circuit.Now we bought second T1 line at remote site and now I have to configure Bounded T1 with Cisco 1921 router.good config example or document on how to configure frame relay bounded T1 ?
View 1 Replies View Relatedi'm having some trouble setting up the correct NAT configuration of a Cisco 1921 router. The NAT is not working as I want - I think my configuration is wrong somewhere. All clients in 172.16.0.0/24 have the correct outgoing address of 1.1.1.3. But the NAT for 10.10.0.4 (and 10.10.0.5, 10.10.0.6) is partially broken: Ping and ssh from the outside world to 1.1.1.4 is "natted" to 10.10.0.4 and works as expected. But from inside (172.16.0.0/24) ssh to 1.1.1.4 should be "natted" to 10.10.0.4, but doesn't work (ping works). ssh from 172.16.0.0/24 to 10.10.0.4 (without doing NAT) works.
network design:
===============
172.16.0.0/16: network for normal use
192.168.64.0/24: network for specific clients and servers
[Code].....
1)For 3650X I found some contradiction in the Q&A about feature set LAN Base vs IP Base:
LAN Base: Can I do static IP routing ?
LAN Base: SVI => is this for intervlan routing ?
2)For 2960, there are 2 flavors (LAN lite and LAN BASE) Q: Can I do static routing on one of these flavors ?
I have a WS-C3750X-12S-S (IP Services) that I THINK I'd like to downgrade to LAN Base so I can stack it with a WS-C3750X-48T-L that is already LAN Base..
View 4 Replies View Relatedcan we upgrade 2960 switch from Lanbase IOS to IPbase
View 4 Replies View RelatedThis is IOS 15.1(4)M3 on a 1921 router. The LAN is 192.168.42.1/24. (DHCP config is further down.) We have a small range that we want to assign via DHCP to devices; .200 through .220 . At the same time, we have a handful of Macintosh systems to which we want to assign a specific address that is not in that 200-220 range. I don't want to configure the assignment based on the Ethernet MAC addresses because these systems might connect via UTP or wireless; that is to say, they have more than one MAC address. They only ever connect using one interface/MAC address at a time, but it's their choice; in some areas wi-fi is available, and in some areas they have to cable-up.
The Mac OSX network settings has a field for "DHCP Client ID". It would be much easier to tell the users of these systems to put their Mac's name in the Client ID field for both their wired and wireless DHCP configs. (As opposed to having them all lookup, and then give me their Ethernet MAC addresses for both of their interfaces.) I tried this with my Mac's (named "shrike") wi-fi interface, but I don't get the 192.168.42.14 address that I expected. I get an address from the .200 to .220 range.
Here's the DHCP-related config from the router:
router#sh run | s dhcp
ip dhcp excluded-address 192.168.42.1 192.168.42.199
ip dhcp excluded-address 192.168.42.221 192.168.42.254
ip dhcp pool OurOffice
network 192.168.42.0 255.255.255.0
[code]....
Is "client-name" the wrong place to configure the DHCP Client ID?
We want to puchase new Cisco ISR 1921/K9 . i want to know does it support the following sample IP-SLA commands
ip sla 2icmp-echo 172.16.1.2timeout 500frequency 1ip sla schedule 2 life forever start-time now
track 10 rtr 1 reachability
delay down 1 up 1
!
track 20 rtr 2 reachability
delay down 1 up 1
ip route 0.0.0.0 0.0.0.0 192.168.1.2 track 10ip route 0.0.0.0 0.0.0.0 172.16.1.2 track 20
Im asking above question because we will need to enable ip-sla on the mentioned router. as i read on the cisco webside, it says Cisco-ISR-1921/K9-IP Base support only IP-SLA RESPONDER feature nothing else. If Cisco-921/K9 does not support the above commands , should i go for ordering Cisco-1921-SEC/K9 ?
I'm planning to use 2 3560X (access switch) on two different locations connected over two 2921 routers in small ring. 3560Xs are directly connected via fiber. Each 3560X is conected to its own 2921, and 2921s are connected together with GRE over IPSec. So they are creating ring.I'm planning to use small area 0 in this scenario. There are less then 200 routes in the network. Will 12.2(55) IP Base on 3560X support this scenario or I will need IP Services image? "OSPF for routed access" is still little vague to me, there are only tipical case study scenarios.
View 22 Replies View RelatedI just would like to confirm if the ASR 1001 with IP Base license can support the normal BGP features such as remote-peering IPV4, Local-AS.
I am not looking for advanced features such as Route Reflectors, VPLS, L2 VPN, etc.
We are trying to migrate WCS base license to NCS 1.1 .We have procured the migration license .In the licensing guide , it is mentioned as "L-WCS-NCS1-M-K9 License first, before adding the licenses migrated from your WCS installation"
1)Whether we need to add this migration license in WCS before genrating XML file or
2)Before adding XML file in NCS we need to add this in NCS ..
I currently purchased, Cisco 1941/K9 with 2 onboard GE, 2 EHWIC slots, 1 ISM slot, 256MB CF default, 512MB DRAM default, IP Base.
Questions
1. With IP Base License, will I be able to run Frame Relay? I really need reference on what works and what doesn't between these different technology package licenses ? Actually frame relay is running on it right now, hope it doesn't suddenly stop after 60 days...
2. As I understand in order to run MPLS, I will need to upgrade to Data License "SL-19-DATA-K9". Since, I already have a Cisco 1941 to upgrade it, I need to order a spare license / paper PAK?
3. Does the IP Base License support site to site IPSEC VPN or do I need to purchase a security license "SL-19-SEC-K9"
4. Can I have both security and data license activated on the same device ?
5. If I do activate security or data license will I be able to use the IP Base features at the same time?
6. If I purchase a new Cisco 1941 with Data or Security License do I need to purchase the IP Base License then upgrade the license?
7. Is the 1941 suited for voice application routing ?
Just bought this switch it has the IP base IOS and I need to use BGP and VRF-lite. My question is can I configure and use these two things without having to upgrade to the IP Services IOS?
View 5 Replies View Relatedwhat iz the difference between 10Base-T and 10 Base-Tx?
View 1 Replies View RelatedCan I connect 2 or more wireless repeaters to the same wireless base station signal to extend wireless coverage? I.e. The base station is located in the centre of the building and the signal covers the middle but not the extreme end of the building. I would like to add a repeater on each opposite sides of the signal's reach so it covers the complete building. I can't use LAN cable and the building has different electricity supply to the 3 different part of the building so can't use the mains to carry the signal. Is this possible using wirless repeaters or do I have to use wireless bridge units to connect to the base station and then output with wireless access points attached to the bridge unit to extend the wirless signal?
View 6 Replies View RelatedHow do I tell if my cisco 2960 has the Lan Base or Lan Lite image?
View 11 Replies View RelatedAny document to explain the differences in the Software images for the ASR1001 routers.
View 3 Replies View RelatedIs there any way to link the Role-based CLI views created in the AAA client to the user created in the ACS 5.2 server? I know that you could do that in ACS 4.2 by using the “cli-view-name” attribute.What I have in mind is to login with some user and that the ACS 5.2 server links this user with a view previously created in the AAA client:This is what I would like to achieve:view configured in the AAA client:parser view DiData secret 5 $1$jPNA$gr9o8gGNmWh9sk8Axbfx91 commands exec include copy running-config ftp commands exec include copy running-config commands exec include copy startup-config ftp commands exec include copy startup-config commands exec include copy commands exec include all show Login to the device using a user created on ACS 5.2 and linked to the above DiData view:
telnet xx.xx.xx.xx
username: cenetacspassword:
Router#?Exec commands: <1-99> Session number to resume copy Copy from one file to another enable Turn on privileged commands exit Exit from the EXEC show Show running system information
Router#
Typing the command "enable view something" is not an option for us.
We have purchased an ASA 5510 with CSC module. Unfortunatelly, white envelope with PAK for activation a Base License was lost before we managed to register it.
View 1 Replies View RelatedI have Cisco 2651XM and currently running old IOS c2600-is-mz.123-26.bin (IP PLUS) which I used the NAT protocol. I was wondering can I use IP-BASE on this router and I am not sure if this feature set has NAT protocol.
View 1 Replies View RelatedOur ACS (5.3) has self signed certificate, we have exported it and declared it in Certificate Authorities.We have exported it to have a Trusted Certificate for client machine.
This certificat has been installed on a laptop.The wlc is successfully setup for eap (peap & eap-fast has been tested > ok)I have this error in the log:
12514 EAP-TLS failed SSL/TLS handshake because of an unknown CA in the client certificates chain.I think the Access Policies (identity & authorization) are misconfigured: [code]
