Add 2 Repeaters To A Base Station?
Aug 23, 2012
Can I connect 2 or more wireless repeaters to the same wireless base station signal to extend wireless coverage? I.e. The base station is located in the centre of the building and the signal covers the middle but not the extreme end of the building. I would like to add a repeater on each opposite sides of the signal's reach so it covers the complete building. I can't use LAN cable and the building has different electricity supply to the 3 different part of the building so can't use the mains to carry the signal. Is this possible using wirless repeaters or do I have to use wireless bridge units to connect to the base station and then output with wireless access points attached to the bridge unit to extend the wirless signal?
View 6 Replies
ADVERTISEMENT
May 20, 2011
I was wondering if it is at all possible to set up a DIR-655 as a wireless base station for any router (specifically a netgear wrg614 v10). I've read that the DIR-655 can be set up as an access point, but with my current situation it's not currently possible.If this is not compatible with this specific netgear router, is there any other solution besides having to purchase a dedicated access point?
View 3 Replies
View Related
Dec 6, 2012
I have two computers, one is a Dell Dimension 8300 while the other is a Compaq Presario Desktop. Both use Microsoft Windows XP OS 32 bit and are networked using a Microsoft Wireless G-Base Station MN-700 on the Dell and a Wireless G-Adapter on the Compaq. This arrangement worked quite well for some time and recently they stopped communicating with each other. I reset the base station as described in the manual. When I did the same for the Adapter I could not enter the correct Wireless Security Key. I tried copying the key from the Base to the adapter but to no avail. Do I have to uninstall both units from their respective computers and reinstall from the CD provided?
View 7 Replies
View Related
Oct 20, 2012
I would like to use my new EA6500 as the base station and another wireless router with Wireless Repeating Function as a repeater. Is the EA6500 capable of that?? I have not found any documentation on that subject.
View 6 Replies
View Related
Mar 28, 2012
1)For 3650X I found some contradiction in the Q&A about feature set LAN Base vs IP Base:
LAN Base: Can I do static IP routing ?
LAN Base: SVI => is this for intervlan routing ?
2)For 2960, there are 2 flavors (LAN lite and LAN BASE) Q: Can I do static routing on one of these flavors ?
View 2 Replies
View Related
May 6, 2012
I have a WS-C3750X-12S-S (IP Services) that I THINK I'd like to downgrade to LAN Base so I can stack it with a WS-C3750X-48T-L that is already LAN Base..
View 4 Replies
View Related
Nov 14, 2011
can we upgrade 2960 switch from Lanbase IOS to IPbase
View 4 Replies
View Related
Jul 25, 2012
I have radio link where i work. Connections have been made to other pcs with an 8 port switch. from that switch i have extended another wire which is nearly 90 mts. that connection iss again connected to several pcs and working fine. But i have again extended another wire of about 90 mts from the 2nd switch. All other connections are working fine on the second switch but there is no light on the switch for the extended one.. Where have i gone wrong? Do i need to place repeaters instead of the second switch??
View 2 Replies
View Related
Apr 21, 2011
I need to setup wireless acces at the warehouse at my work. I have 3 D-Link DWL-2100AP's. 1 is connected to a switch and working properly as an access point. I was able to get another working as a repeater (WLAN light on) but cannot get the 3rd working as a repeater. I configured both repeaters the same way but with different ip addresses. (AP- .10, Repeater1 - .11 and Repeater2 - .12).
I guess the main thing I'm not understanding is how the 2nd repeater connects to the first repeater. Is it supposed to connect to the 1st repeaters MAC or to the AP's MAC? If I unplug the AP, the 2nd repeater won't pick up the 1st repeaters MAC. Both repeaters were connected to the AP. basically Switch -> AP -> Repeater -> Repeater.
View 5 Replies
View Related
Oct 22, 2012
I'm currently contemplating on purchasing a 2nd WRT54G router with dd-wrt as a 2nd wireless repeater in the house. Just wondering if this would be possible. Current setup is Main router (D-Link DIR-615) on 3rd floor > WRT54G as wireless repeater on 2nd floor. I don't mind the loss of connection speed since the main purpose is to increase coverage to the 1st floor.
View 4 Replies
View Related
Jul 20, 2011
I have an old metal-walled mobile home that I plan on converting to a combination shop and man-cave; it's about 200 feet from my home's computer room, where I have a Netgear WNDR3400 wireless-n router. The only place in the trailer where I can "see" my home network is the kitchen window, and I thought about putting a Wi-Fi repeater there to extend the home network into the trailer. But I have read that using a repeater will cut the network's Wi-Fi throughput in half -- which would not please my wife and daughters back at the house. Is there a simple, relatively inexpensive way to extend the network to the trailer without slowing everything down? Eventually I may have Charter install a separate cable hookup there, which would allow a separate high-speed Internet connection too. For now, I just want to "share" Wi-Fi to the trailer.
View 6 Replies
View Related
Aug 22, 2011
We have 4x WAP4410N access points 1 AP & 3 Repeaters, this works perfect. The situation at the moment is that the internet connection is plugged in with a cable on the AP but the question is that if it's possible to plug the internet connection into one of the repeaters?
After that are we still able to use the internet over al four access points?
View 1 Replies
View Related
Apr 3, 2012
Here's the current configuration in our organization (which I believe is incorrect):We have a number of Cisco 1500 series AP's (22 in total), that are mounted outdoors to provide seamless WiFi coverage over a large area. Each AP however has its own physical ethernet connection back to the WLC (All the AP's are marked as Root AP's). They are all broadcasting the same SSID. We have tried to stagger the channel selection but because there are only three non-overlapping channels to choose from, and in some areas the density of AP's is quite high, there is multiple places of channel interference. With this configuration we experience 100-150 disconnects from clients every day. (Our clients are mobile so they move throughout the coverage area constantly).
My idea is to switch the AP's to the same channel thereby forming a wireless mesh, use the built in functionality of the 1500 series to use 802.11a as the backhaul, designate one or two AP's as root AP's and wire them back to the WLC. Thereby forming a WiFi mesh, which if I'm not mistaken is the point of the 1500 series in the first place!
I am however completely new at WiFi networks and wondering if I am simply mistaken in what I believe my proposed changes will enable, or if there is a better way to tackle the WiFi topology.
View 1 Replies
View Related
Mar 23, 2012
I bought a tp-link WA701ND and a netgear WGR614. i wish to pick up signal using 701 and then let 614 repeat it. no more tech support coz im already broke.
View 1 Replies
View Related
Aug 19, 2012
I'm using an HP Elitebook 6930p with Windows XP and an HP EN488UT docking station. When I use the computer by itself the Network Connections shows "Local Area Connection 3 Connected Intel 83567LM Gigabit Network Connection" and I can connect to the internet. When I am in the docking station, I can also see this connection, as long as my notebok is open when I start up. However, if i start the computer with the lid closed (I just want to use the external monitor, not the notebook monitor) that network connection does not appear and I cannot connect to the intenet.
[code]....
View 5 Replies
View Related
Nov 28, 2011
What are procedures to deactivate di-604+di-704 routers+make the repeaters,connecting each of them,in a wired fashion,to my Belkin wireless N router?
View 1 Replies
View Related
Mar 10, 2011
what is a diskless station in networking
View 1 Replies
View Related
Oct 16, 2012
if the network i'm planning on will even work so i drew a picture on my project (attached). All cables will be gigabit compatible as will be the switches. The reason i will have 2 switches is because they won't be in the same building. The uppermost switch will be physically next to the router to enable me to have gigabit connection between the DiskStation and the PCs/HTPC without having to change my router (in fact can't change it due to special firmware for my internet TV).
View 4 Replies
View Related
May 1, 2012
We would like to install a wireless network throughout the station. Currently we have a wired network with 15 PC's and are looking at obtaining tablets for our squads and apparatus. The station is quite large and is divided by the vehicle bays.I'm thinking that we will need multiple access points throughout the station. I am familiar with setting up one wireless router but not with multiple access points.
View 2 Replies
View Related
Feb 28, 2012
I have the Air Station WHR-G300N. I just moved here from CA, I was on Verizon and now trying to use it on my girlfriend Cox system I can't get it to operate correctly.
Her PC system stopped having internet connection after about 2 weeks(running on the router) and going with Cox's reboot procedure of eliminating the router it can back up and seems to work fine as soon as I hook it back to the modem it stops.
I have unplugged all cables waited 30 seconds on both systems a couple of times. The lights are on the modem and the router.
View 1 Replies
View Related
May 18, 2012
I am trying to install ACS 5.0 on workstation, however once the install finsihes it reboots and I enter the Linux bash command line rather than the Cisco CLI.
Note - this is now fixed. I followed the steps here to install ACS 5.0 on VMware Workstation 7: url...
View 2 Replies
View Related
Mar 28, 2013
I am blocked with the below doubt for my issue resolution. When a ethernet frame for eg:ARP Packet of minimum length (64 bytes) is received at the end station, will the L2 layer remove both FCS and extra padding bytes(18 padding bytes for ARP)? Or removal of the padding bytes is dependent on the implementation?
View 2 Replies
View Related
Dec 7, 2012
i have 10 stations, and i think one of them generated allot of traffic.maybe a virus sending spam.is there a command that can show my which station consume bandwidth?
View 3 Replies
View Related
Jun 24, 2012
In ACS 5.3 radius authentication report I want to show the called-station-id attribute. (this was appearning on failed and passed auth in ACS 4.2). The value of called-station-id appears in the details. However, I want it to appear as a column with the report.
View 2 Replies
View Related
Oct 26, 2011
I have a Latitude D820, Windows XP, SP3. At my office I have a regular docking station but at home I have a D/Dock docking station. When I dock the 820 at home the Broadcomm network card works flawlessly. When I dock it in the office, it will occasionally work but most of the time the link light and data light on the docking station are on solidly and XP reports that the cable is unplugged. I have tried two different docking stations with identical results and also tested the cable by plugging it into the docking station that holds a D810. With the D810 it worked normally.
View 1 Replies
View Related
Oct 6, 2010
I want to connect from a Linux station to RV082, is it possible? What software can I use and with what configuration?
View 2 Replies
View Related
Nov 10, 2012
Samsung CY-WDCA7UT/ZA USB Central Station Dongle driver?
View 1 Replies
View Related
Feb 12, 2013
My buffalo link station 3t was giving me problems due to avg firewall blocking access to my drive. so switched it off to work . now that the drive is working but now when i click to access the drive the back ground on the desktop goes black on windows 7 its a acer laptop and the graphics are blurey.
View 1 Replies
View Related
May 5, 2012
I had a W120N wireless router which received all internet radio stations with no problemsI have just acquired an E3000 and it appears to not pass through 2 particular internet stations that worked fine on the 120N What configuration parameters affect internet radio?Currently, I'm using all the same parameters from the 120N where possible.
View 4 Replies
View Related
Mar 14, 2004
I have a Latitude D400 laptop with docking station. I left on a trip for a week and came back to find I cannot connect to the network through the docking station. I can however connect if I plug the ethernet cable directly into the laptop. Is this a hardware problem with the docking station?
View 3 Replies
View Related
Oct 7, 2012
When I connect my Android device (Nook) via the HotSpot "Local Area Connection" it has a strong signal, but for some reason cannot load any https webpages, such as gmail.com. It always says "web page not available" when I know the sites are working. Previously it connected without any problems but now only non-secure websites are accessible; I don't know what has caused the change.
My device connects with no such problem via the larger wireless network here (security is WEP), but the signal is weak so I prefer to use the HopSpot connection.
I have a XPS with HotSpot 1.1.0.0. The device says it is connected to HotSpot with WPA/WPA2 PSK.
View 6 Replies
View Related
Feb 28, 2011
I have a HP 6530b Laptop, and on-board Broadcom NetLink Gigabit Ethernet adapter.When I remove my laptop from the docking station, I obviously lose Network connectivity, however, when I replace the laptop back (or even just plug in a cable directly), I cannot reconnect to the network until I reboot.When I open Network and Sharing Center (Win7), and click change adapter settings the adapter is missing from the list (after i have removed laptop from docking station).
View 1 Replies
View Related
Mar 19, 2013
-Region : Spain
-Model : TD-VG3631
-Hardware Version : V1
-Firmware Version : 0.6.0 1.0 v0001.0 Build 130108 Rel.54595n
I have a problem with the VoIP feature of this router:I configure the router as a sip station of a asterisk local PBX (192.168.1.254),To this point everything is fine, I can call with a asterisk sip station to a analog phone (sip station 100) that is conected to the FXE port of the TPLINK,The problem occurs when I want to call with the analog phone to a sip station. I have a dial plan with a 0 prefix to call stations using the sip acount:Profile Name Registrar Address Phone Number Status Remove Edit Prueba192.168.1.254100up.And when I call, I can see in the log the INVITE action.
View 1 Replies
View Related
