Connection Between The Disk Station And The PCs / HTPC
Oct 16, 2012
if the network i'm planning on will even work so i drew a picture on my project (attached). All cables will be gigabit compatible as will be the switches. The reason i will have 2 switches is because they won't be in the same building. The uppermost switch will be physically next to the router to enable me to have gigabit connection between the DiskStation and the PCs/HTPC without having to change my router (in fact can't change it due to special firmware for my internet TV).
View 4 Replies
ADVERTISEMENT
Mar 14, 2004
I have a Latitude D400 laptop with docking station. I left on a trip for a week and came back to find I cannot connect to the network through the docking station. I can however connect if I plug the ethernet cable directly into the laptop. Is this a hardware problem with the docking station?
View 3 Replies
View Related
Mar 9, 2012
I am using a wireless connection via router to access internet at home. When my Dell Latitude E6510 Laptop is not on the Dell Docking Station and I'm using as just standalone I can access my wireless connection easily, no problem at all.However, when I attached my laptop to my Dell Docking Station, I can not access my wireless connection. The wireless connection is found, but when I click connect to network, I get "Windows cannot found network". When I remove the laptop from the docking station, I find the wireless connection and connect perfectly and it works normal.I am using Windows 7. I can connect to internet with straight wire going to docking station easily, but no wireless connection found when laptop is on the docking station. I work from home and use the docking station for two monitors for doing my job. I have struggle with this problem for two weeks now. I don't see anything on the docking station that's preventing me from access my wireless connection.
View 1 Replies
View Related
Mar 25, 2012
I cannot utilize my Ethernet connection when my Dell Latitude D630 is connected to a docking station. I have tried this on two different docking stations. I also have another Dell laptop that I have used in the one of the same docking stations and the ethernet connection is fine. I'm looking for assistance to troubleshoot this (even just determining if I can replace the connector and how I determine what type I need)
View 3 Replies
View Related
Jan 4, 2012
I have a NETGEAR XAVB101 Powerline AV Ethernet Adapter and an AMD Llano build HTPC which refuses to work with each other. The power plug works well with my Gateway NV79 laptop and even my Intel Core i5 -2500K desktop, without any problems! I have also used it to connect to my Roku, Yamaha Network Receiver and other networked stuff and all worked great, just the HTPC seems to have issues connecting to the network!The HTPC is AMD A6-3650 on a ECS FM1 A75 Mobo with Integrated Realtek RTL8111E Gigabit Ethernet Controller, which is what I am connecting the power plug to! Only the connection over the power line adapter does not work, it works great with both a connection directly from the router and with wireless!
The adapter has a 128 bit encryption push button security feature which I'm NOT using. When I connect it the HTPC tries to connect and fails and shows the network as connected to an unidentified network. My LAN drivers on the computer is all up-to-date.
View 4 Replies
View Related
Jan 4, 2012
I have a NETGEAR XAVB101 Powerline AV Ethernet Adapter and an AMD Llano build HTPC which refuses to work with each other.
The power plug works well with my Gateway NV79 laptop and even my Intel Core i5 -2500K desktop, without any problems! I have also used it to connect to my Roku, Yamaha Network Receiver and other networked stuff and all worked great, just the HTPC seems to have issues connecting to the network!
The HTPC is AMD A6-3650 on a ECS FM1 A75 Mobo with Integrated Realtek RTL8111E Gigabit Ethernet Controller, which is what I am connecting the power plug to! Only the connection over the power line adapter does not work, it works great with both a connection directly from the router and with wireless!
The adapter has a 128 bit encryption push button security feature which I'm NOT using. When I connect it the HTPC tries to connect and fails and shows the network as connected to an unidentified network. My LAN drivers on the computer is all up-to-date!
View 14 Replies
View Related
Oct 4, 2012
[code] Wireless transfer from HTPC to Windows Home Server peak at 8-9 MB/sec. Note that my WHS and my Winn7 Gaming rig are both on the same physical switch, but the same exact wireless file transfer from my HTPC to Windows 7 gaming rig hits consistent 35-40 MB/sec, 4x faster and which is what I expect. Wired transfer of same 4GB test file directly from gaming rig to WHS tops over 100MB/sec so it is not a problem with the WHS writing to disk or wiring. So the question is, what could possibly be bottle-necking my upload from HTPC only to the Home Server? I have tested a Netgear R6300 with the same results as the Asus router.
View 1 Replies
View Related
Jan 3, 2012
I have a NETGEAR XAVB101 Powerline AV Ethernet Adapter and an AMD Llano build HTPC which refuses to work with each other.
The power plug works well with my Gateway NV79 laptop and even my Intel Core i5 -2500K desktop, without any problems! I have also used it to connect to my Roku, Yamaha Network Receiver and other networked stuff and all worked great, just the HTPC seems to have issues connecting to the network!
The HTPC is AMD A6-3650 on a ECS FM1 A75 Mobo with Integrated Realtek RTL8111E Gigabit Ethernet Controller, which is what I am connecting the power plug to! Only the connection over the power line adapter does not work, it works great with both a connection directly from the router and with wireless!
The adapter has a 128 bit encryption push button security feature which I'm NOT using. When I connect it the HTPC tries to connect and fails and shows the network as connected to an unidentified network. My LAN drivers on the computer is all up-to-date!
View 19 Replies
View Related
Aug 19, 2012
I'm using an HP Elitebook 6930p with Windows XP and an HP EN488UT docking station. When I use the computer by itself the Network Connections shows "Local Area Connection 3 Connected Intel 83567LM Gigabit Network Connection" and I can connect to the internet. When I am in the docking station, I can also see this connection, as long as my notebok is open when I start up. However, if i start the computer with the lid closed (I just want to use the external monitor, not the notebook monitor) that network connection does not appear and I cannot connect to the intenet.
[code]....
View 5 Replies
View Related
Aug 23, 2012
Can I connect 2 or more wireless repeaters to the same wireless base station signal to extend wireless coverage? I.e. The base station is located in the centre of the building and the signal covers the middle but not the extreme end of the building. I would like to add a repeater on each opposite sides of the signal's reach so it covers the complete building. I can't use LAN cable and the building has different electricity supply to the 3 different part of the building so can't use the mains to carry the signal. Is this possible using wirless repeaters or do I have to use wireless bridge units to connect to the base station and then output with wireless access points attached to the bridge unit to extend the wirless signal?
View 6 Replies
View Related
Mar 10, 2011
what is a diskless station in networking
View 1 Replies
View Related
May 1, 2012
We would like to install a wireless network throughout the station. Currently we have a wired network with 15 PC's and are looking at obtaining tablets for our squads and apparatus. The station is quite large and is divided by the vehicle bays.I'm thinking that we will need multiple access points throughout the station. I am familiar with setting up one wireless router but not with multiple access points.
View 2 Replies
View Related
Feb 28, 2012
I have the Air Station WHR-G300N. I just moved here from CA, I was on Verizon and now trying to use it on my girlfriend Cox system I can't get it to operate correctly.
Her PC system stopped having internet connection after about 2 weeks(running on the router) and going with Cox's reboot procedure of eliminating the router it can back up and seems to work fine as soon as I hook it back to the modem it stops.
I have unplugged all cables waited 30 seconds on both systems a couple of times. The lights are on the modem and the router.
View 1 Replies
View Related
May 18, 2012
I am trying to install ACS 5.0 on workstation, however once the install finsihes it reboots and I enter the Linux bash command line rather than the Cisco CLI.
Note - this is now fixed. I followed the steps here to install ACS 5.0 on VMware Workstation 7: url...
View 2 Replies
View Related
May 20, 2011
I was wondering if it is at all possible to set up a DIR-655 as a wireless base station for any router (specifically a netgear wrg614 v10). I've read that the DIR-655 can be set up as an access point, but with my current situation it's not currently possible.If this is not compatible with this specific netgear router, is there any other solution besides having to purchase a dedicated access point?
View 3 Replies
View Related
Mar 28, 2013
I am blocked with the below doubt for my issue resolution. When a ethernet frame for eg:ARP Packet of minimum length (64 bytes) is received at the end station, will the L2 layer remove both FCS and extra padding bytes(18 padding bytes for ARP)? Or removal of the padding bytes is dependent on the implementation?
View 2 Replies
View Related
Dec 7, 2012
i have 10 stations, and i think one of them generated allot of traffic.maybe a virus sending spam.is there a command that can show my which station consume bandwidth?
View 3 Replies
View Related
Jun 24, 2012
In ACS 5.3 radius authentication report I want to show the called-station-id attribute. (this was appearning on failed and passed auth in ACS 4.2). The value of called-station-id appears in the details. However, I want it to appear as a column with the report.
View 2 Replies
View Related
Oct 26, 2011
I have a Latitude D820, Windows XP, SP3. At my office I have a regular docking station but at home I have a D/Dock docking station. When I dock the 820 at home the Broadcomm network card works flawlessly. When I dock it in the office, it will occasionally work but most of the time the link light and data light on the docking station are on solidly and XP reports that the cable is unplugged. I have tried two different docking stations with identical results and also tested the cable by plugging it into the docking station that holds a D810. With the D810 it worked normally.
View 1 Replies
View Related
Oct 6, 2010
I want to connect from a Linux station to RV082, is it possible? What software can I use and with what configuration?
View 2 Replies
View Related
Nov 10, 2012
Samsung CY-WDCA7UT/ZA USB Central Station Dongle driver?
View 1 Replies
View Related
Feb 12, 2013
My buffalo link station 3t was giving me problems due to avg firewall blocking access to my drive. so switched it off to work . now that the drive is working but now when i click to access the drive the back ground on the desktop goes black on windows 7 its a acer laptop and the graphics are blurey.
View 1 Replies
View Related
May 5, 2012
I had a W120N wireless router which received all internet radio stations with no problemsI have just acquired an E3000 and it appears to not pass through 2 particular internet stations that worked fine on the 120N What configuration parameters affect internet radio?Currently, I'm using all the same parameters from the 120N where possible.
View 4 Replies
View Related
Oct 7, 2012
When I connect my Android device (Nook) via the HotSpot "Local Area Connection" it has a strong signal, but for some reason cannot load any https webpages, such as gmail.com. It always says "web page not available" when I know the sites are working. Previously it connected without any problems but now only non-secure websites are accessible; I don't know what has caused the change.
My device connects with no such problem via the larger wireless network here (security is WEP), but the signal is weak so I prefer to use the HopSpot connection.
I have a XPS with HotSpot 1.1.0.0. The device says it is connected to HotSpot with WPA/WPA2 PSK.
View 6 Replies
View Related
Feb 28, 2011
I have a HP 6530b Laptop, and on-board Broadcom NetLink Gigabit Ethernet adapter.When I remove my laptop from the docking station, I obviously lose Network connectivity, however, when I replace the laptop back (or even just plug in a cable directly), I cannot reconnect to the network until I reboot.When I open Network and Sharing Center (Win7), and click change adapter settings the adapter is missing from the list (after i have removed laptop from docking station).
View 1 Replies
View Related
Dec 6, 2012
I have two computers, one is a Dell Dimension 8300 while the other is a Compaq Presario Desktop. Both use Microsoft Windows XP OS 32 bit and are networked using a Microsoft Wireless G-Base Station MN-700 on the Dell and a Wireless G-Adapter on the Compaq. This arrangement worked quite well for some time and recently they stopped communicating with each other. I reset the base station as described in the manual. When I did the same for the Adapter I could not enter the correct Wireless Security Key. I tried copying the key from the Base to the adapter but to no avail. Do I have to uninstall both units from their respective computers and reinstall from the CD provided?
View 7 Replies
View Related
Mar 19, 2013
-Region : Spain
-Model : TD-VG3631
-Hardware Version : V1
-Firmware Version : 0.6.0 1.0 v0001.0 Build 130108 Rel.54595n
I have a problem with the VoIP feature of this router:I configure the router as a sip station of a asterisk local PBX (192.168.1.254),To this point everything is fine, I can call with a asterisk sip station to a analog phone (sip station 100) that is conected to the FXE port of the TPLINK,The problem occurs when I want to call with the analog phone to a sip station. I have a dial plan with a 0 prefix to call stations using the sip acount:Profile Name Registrar Address Phone Number Status Remove Edit Prueba192.168.1.254100up.And when I call, I can see in the log the INVITE action.
View 1 Replies
View Related
Oct 20, 2012
I would like to use my new EA6500 as the base station and another wireless router with Wireless Repeating Function as a repeater. Is the EA6500 capable of that?? I have not found any documentation on that subject.
View 6 Replies
View Related
Oct 29, 2012
We have been having issues with random packet drops and or some sort of radio lockup which happens a few times a day. I have a test AP setup with a few clients only a few feet away and I see this combination of messages. Should I be seeing these clients drop off and then reconnect immediately? Granted these test clients are not passing much data but my assumption is that they would not become deauthenticated because of lack of activity? This setup is using a radius server for authentication. I tested it before with just WPA2 PSK and only had a few disconnected over a number of days, compared with many a day with the Radius.
View 1 Replies
View Related
Oct 9, 2012
We have 5 Cisco Aironet 1100 wireless access points and we are having huge problems in the last few days with them disconnecting some mobile barcode scanners that we have.
We have two Aironet's in the top of the factory which work fine and 3 down the bottom which keep kicking the barcode scanners off. If we use the barcode scanners at the top of the factory they work fine, as soon as we come down to the other 3 WAPs it they keep connecting and disconnecting.
We get the following error in the Event log on the access points.Disassociated because sending station is leaving (or has left) BSS On the barcode scanners. [code]
View 1 Replies
View Related
Jan 25, 2013
I own a Nanostation5 Loco, and I have a router behind it.I would like to add a DHCP Lease to that router and do a port forward to the router.I can not find the DHCP Lease option in Nanostation settings, but if I choose to see DHCP Leases in "Extra info" on main page I can see some MAC and IP addresses there.When it comes to port forwarding, I fill the form slots with info, and when I press OK to save it a pop-up comes saying "Please fill out this field", a field for another forward rule.
View 3 Replies
View Related
Mar 19, 2013
Region : Spain
Model : TD-VG3631
Hardware Version : V1
Firmware Version : 0.6.0 1.0 v0001.0 Build 130108 Rel.54595n
ISP :
I have a problem with the VoIP feature of this router:I configure the router as a sip station of a asterisk local PBX (192.168.1.254),To this point everything is fine, I can call with a asterisk sip station to a analog phone (sip station 100) that is conected to the FXE port of the TPLINK,The problem occurs when I want to call with the analog phone to a sip station. I have a dial plan with a 0 prefix to call stations using the sip acount:Profile Name Registrar Address Phone Number Status Remove Edit Prueba192.168.1.254100up And when I call, I can see in the log the INVITE action :
32013-03-19 10:16:33OTHERDebugport 1 cx 0x3, evt/reason 3/0 buf (nil)
42013-03-19 10:16:01OTHERDebugport -1 cx 0x3, evt/reason 1/4 buf 0x4761a8
52013-03-19 10:16:01OTHERDebugthe initial INVITE request for [accIndex(0),callIndex(3) dest(<sip:103@192.168.1.254>)] is sen
But I�am sniffing traffic in the PBX and not received the invitation... Obviously the 103 station never recive the call...I think that maybe the INVITE is going out behind the WAN interface.... bug version?
View 1 Replies
View Related
Jun 16, 2013
I am using the Vostro 3360 with win 7, I did used the hotspot station software accomplish with the WiFi driver before and worked fine. However, the hotspot is not working as the ipv4 is showing 'no internet connect'. And my iPhone cannot connect it too.
View 1 Replies
View Related
