Cisco :: 2610 Which IOS Should Take Specification Of Router
Apr 5, 2013I'm just about to update flash on my router 2610, but I don't know which IOS i should take that's specification of my router: [code]
View 6 Replies
ADVERTISEMENT
Cisco WAN :: IOS For 2610 Router With 4MB Flash?
Jan 15, 2011I erased my flash and cannot locate an IOS that will fit on my 2610 router, I was running 11.3(7), but cannot locate anything even close.
View 3 Replies View RelatedCisco WAN :: Loopback Testing On 2610 Router
Jun 22, 2011I am working at a client site today. The client has a large Frame Relay Hub Spoke network. The Hub is at the HQ location, and then there are about 15 spoke sites in remote offices.
We are having an issue with the frame between the HQ and one of the spokes. We are currently working with our dear friends at AT&T to troubleshoot the issue. AT&T yesterday was trying to run a local loop test to the router at the remote (spoke) end. We were working iwth them in trying to put the remote router (which we manage) into a loopback mode. We were trying to use controller commands
COOP-Rappahanock#conf t
Enter configuration commands, one per line. End with CNTL/Z.
COOP-Rappahanock(config)#controller ?
% Unrecognized command
COOP-Rappahanock(config)#controller
That we seem to run out of options...
How can we put the subinterface that is the other end fo the frame into loopback mode so that a local loop test can be done between us and AT&T (provider)?
Cisco :: View Hardware Information Of 2610 Router?
Jan 6, 2012I have a Cisco 2610 series router(Version 12.0(5)T1, c2600-i-mz.120-5.T1), which has a network module inserted. I would like to view the model of this network module. There are no "show inventory" or "show platform" commands. "Show version" doesn't list the network module as well. In addition, it appears to have a "show c2600" command, but this doesn't display any hardware information.
View 14 Replies View RelatedCisco Infrastructure :: 2610 Router Connected To Satellite Modem
Dec 1, 2004I have a cisco 2610 router connected to satellite modem (CDM-600). Cisco has NM-2W module with WIC-2T card, one port of this card is connected to modem via CAB-SS-530MT=, chassis WIC slot is filled with 2MFT-E1. Everything works fine for several hours. Then serial interface (connected to modem) goes down, and never comes up. I see following messages in the log. [code]
View 4 Replies View RelatedCisco Switching/Routing :: 2610 Router What Speed Is Built In Ethernet Port
Oct 23, 2011I have a 2610 router. How can I tell if the built-in ethernet port is only a 10BASE-T or if it's a 10/100 port? Is there a "Show" command to give me this information or did it only come one way? I have found conflicting information on this :-( If it's only 10BASE-T, can I upgrade it to 10/100?
View 8 Replies View RelatedHow To Remember Ethernet Specification
Jul 5, 2011I noticed alot of question about ethernet, distances, differences, bandwidth, throuput etc of different types. I have a list off all from 10base2 all the way upto 10000baseEW, but there are so many how am I meant to remember all the differences..?
View 8 Replies View RelatedCisco Firewall :: What User Specification With Asa5505 Means
Nov 30, 2011What the user specification with the asa5505 means.there is a 50 user and an unlimited license with the asa5505. with 50 user does this mean that only 50 user can work simultaneously over the asa, or what?
View 10 Replies View RelatedCisco Switching/Routing :: The Specification Of Cat3550 About SVI's Mac Address
Jan 22, 2013I would like to know why Cat3550 SVI's mac address is always same.for example if I configure interface vlan1 and vlan2.mac address is same as like 000d.bdfc.xxxx but Cat3750 is different, each SVI has unique mac address.
View 1 Replies View RelatedRouters / Switches :: Electrical Specification Of Cat-5e Cable
Feb 7, 2011electrical specification of cat-5e cable
View 1 Replies View RelatedCisco WAN :: Find Website Specification Of Power Cables For ASR1002
Jun 5, 2013I am trying to find on Cisco's web site the specification of their power cables for the ASR1002. I am particularly interested in the NEMA specification for the US power cable CAB-AC-RA .
View 2 Replies View RelatedCisco Wireless :: AP541N Specification For Ack Time Adjusting And Survey
Nov 8, 2010Some deep technical questions regarding the AP541N access point? What I want to know is, if the AP has: - Watchdog per IP - ACK time adjusting - Site Survey.
View 1 Replies View RelatedCisco Switching/Routing :: 6509 BGP X Autonomous System Specification
Mar 25, 2012I am trying to configure BGP on 6509 IOS. I can not specify a long interger for autonomous system: ASN: 262829 (32 bits)
View 1 Replies View RelatedCisco Firewall :: 871 / 2811 / 1841 - ZBFW Default Inspection Specification
May 6, 2011I can't find any specific information on the implementation of packet inspection in a zone based policy firewall. In other words, is there a specification or even just a set of values that define the default inspection parameters for all protocols? With DPI I can manage 'some' of the inspection capabilities but I have some fairly rigorous and specific requirements to meet and I need to validate that the IOS ZBFW will meet those requirements. Specifically, I'm interested in HTTP, DNS, and ICMP but all other protocols would be useful as well.I'm working with basic routers; 871's, 2811's, 1841's, etc. The IOS in use in most cases is adventerprisek9-mz.151-3.T.
View 4 Replies View RelatedCisco Switching/Routing :: Finding Specification For 3750x PoE Power Supply?
Jul 11, 2012Looking at the specs for the 3750 power supply - is the WS-C3750X-48P-S model with the 715W power supply referring to the amount for both power supplies per switch or just one power supply per switch? Meaning, is the 715 a accumulative number or, just the watts of one power supply. I would like to purchase a 3750x PoE switch with redundant power supplies. If this model is not the correct one?give me the model that offers 48 port PoE with redundant power supplies?
View 6 Replies View RelatedCisco WAN :: 2610 Non XM With NM-16ESW?
Feb 28, 2011i recently bought and installed a working NM-16ESW into my cisco 2610.HOWEVER:i have tried different IOS's:c2600-ik9o3s-mz.122-46a.binc2600-io3-mz.122-46a.binc2600-io3-mz.123-26.bin and unfortunately non of those IOS versions works with the NM-16ESW.Heres my SHOW DIAG command:
Router#show diagSlot 0: C2610 1E Mainboard Port adapter, 3 ports Port adapter is analyzed Port adapter insertion time unknown EEPROM contents at hardware discovery: Hardware Revision : 3.0 PCB Serial Number : JAD05470D9S (1580012177) Part Number : 73-2839-14 RMA History : 00 RMA Number : 0-0-0-0 Board Revision : B0 Deviation Number : 0-0 EEPROM format version 4 EEPROM contents (hex): 0x00: 04 FF 40 00 91 41 03 00 C1 18 4A 41 44 30 35 34 0x10: 37 30 44 39 53 20 28 31 35 38 30 30 31 32 31 37 0x20: 37 29 82 49 0B 17 0E 04 00 81 00 00 00 00 42 42 0x30: 30 80 00 00 00 00 FF FF FF FF FF FF FF FF FF FF 0x40: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
[code].....
Cisco WAN :: 2610 - How To Test Setup Some ACL
Jan 26, 2012I am trying to test and setup some ACL's on a switch, the current setup is:
Core Switch - HP ProCurve 2610-24-PWR
Edge Switch - HP ProCurve 2510-24
VLANS 5, 10, 15, 20, 25, 30
I want to deny access to VLAN 5 from VLAN 20 which is are client VLAN.
Cisco : 1721 / 2610 - Old T1 Wic Is Not Interacting To V2
Sep 18, 2011I've got three Cisco 1721's and a 2610, two of the 1721's are 32f's, the other one is a bit older but is still the same model. The two Cisco 1721 32f's have 1-dsu-t1-v2 wics in them, and the older 1721 has a 1-dsu-t1 wic in it. Now no matter how i have configured it the old t1 wic will not talk to the v2 wic. I've tried putting the old wic into a 1721 32f and it doesn't work at all!
What i have working:
router DCE (1721 32f with v2 wic) can talk to router DTE (1721 32f with v2 wic) no problem with this configuration.
Router DCE:
-service-module t1 clock source internal
-service-module t1 data-coding normal
[ code].....
Router DTE:
-service-module t1 clock source line
-service-module t1 data-coding normal
[ code]....
Router OLD (1721 with v2 wic) can talk to router DTE (1721 32f with v2 wic) no problem with same config. What doesn't work: Any router with 1-dsu-t1 (old) wic to router DTE (1721 32f with v2 wic). again same configuration as before, so whats going on that i cant get this to work? Is the old t1 wic not compatible with the new t1 wic?
Cisco WAN :: 2610 Connecting 2 Routers With Only Fast Ethernet
Apr 28, 2013I have a home lab. I am trying to connect a 1710 to a 2610 with just using the fast ethernet ports. I understand that serial connections and t1 csu/dsu connections use clocking, etc. How can I configure FA ports to do the same AND be routable?
View 6 Replies View RelatedCisco WAN :: 2610 Testing Out Frame Relay Connections
Mar 13, 2012I'm looking to test fram relay connections in a lab environment i'm building at home. I have a couple of 2610 routers that are barebones and am looking to get some serial modules. Are (2) WIC-2T's all I would need to create those test connections? Also on a side note are the any modules for the 2610 that have fast ethernet connections. I would like to have that so I can create a router on a stick model off of the 2600's.
View 1 Replies View RelatedCisco Switching/Routing :: 2610 - No Internet Access?
Mar 2, 2012I have a Cisoc 2610 connected to my network, 1 Ethernet port and a WIC-2T card. I have ther serial connection to the main router and the ethernet going to the switch. I can ping all device throught the network...but the 2610 can't ping any outside address (no internet connection). I have the internet connection going through my 3745 (which the 2610 is connected to via serial cable). I put a default route into the 2610 but still no luck.
Here are the running configs:
2610:
version 12.3
service timestamps debug uptime
service timestamps log uptime
[Code].....
Cisco Switching/Routing :: 2610-non Responsive Device
Nov 16, 2012I hope I'm posting this in the correct place. I have a 2610 router and on starting it up i get this and only this,
"System Bootstrap, Version 11.3(2)XA4, RELEASE SOFTWARE (fc1)
Copyright (c) 1999 by Cisco Systems, Inc.
TAC:Home:SW:IOS:Specials for info"
thats all and exactly what is displayed on the console screen the device is none responsive.
HP Pro Curve 2650 And 2610 VLAN Infrastructure?
Mar 3, 2013I have 2 Procuve Switches one is 2650 were all the Department PC's & Wireless access points connected & second one is 2610 were i have the firewall connected,Active Directory & Windows DHCP Server
Switch 1- 2650
Ports
Port 1-16 is used by HR Department
Port17-32 is used by Finanace Department
Port 33-34 is used by Access Points
Port 41-48 is used by Users
Port 50 is used to uplink to switch 2610.What i wanted to achive is Isolcate Departments & Users & Access Points through VLAN from each other but they should be able to hit our Active directory for authentication, Firewall for internet & DHCP Server for IP's.
Cisco Switching/Routing :: 2610 Configured IP Addresses On Interfaces
Feb 10, 2013I'm working on my CCNA. I purchased an old router 2610 with two ethernet ports. I configured the IP addresses on the interfaces and added the default gateway. I configured NAT to go out my ATT DSL router to the internet. With the 2610, I'm able to ping the back end or internal DSL router, but I can't ping the front end, external router, or out to any internet site such as google.
View 10 Replies View RelatedCisco LAN :: 3550 / 2610 - Connect 2 Routers To Cable Modem
Oct 29, 2012i have 2 routers with a switch and pc connected to the switch. i am working on RIP and i enabled it on both routers.
my current set up is this:
PC---Switch(3550)---Router2(2610)---Router1(2610)--- Cable modem
I am able to ping from pc to Router1. I am able to ping 4.2.2.2 and google from Router1 but unable to ping it from Router 2 and pc.
Here is my config for Router1:
Current configuration : 1089 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
[code].....
Cisco WAN :: 2610 / Windows 7 Can't Ping Past Local Interface
Jul 18, 2012Ive got my home lab setup with two 2610 routers hooked togeather with a DTE/DCE Crossover and I have OSPF configured on both routers. Each router has one 3550 switch connected to each FA0/0 inteface. The issue is that Everything can be pinged except my windows 7 PC connected to the R1 LAN. Everything else can be pinged from any other device. I checked the PC gateway configuration, disabled the firewall and checked my switch configuration! Is their something that I need to change in Windows?
Windows PC ------------ 3550 Switch-------------R1-----------------------------------R2---------------------3550 Switch----------------------Linux Box
Windows PC can't ping past the FA0/0 interface between the switch and R1
Cisco WAN :: 2612 And 2610 Maximum Number Of Nat Translation Table Entries
Jan 7, 2013what is the size of nat table for cisco router 2612 and 2610 and what is the maximum number of nat translation table entries
View 1 Replies View RelatedCisco :: Monitor Routers 2610 / 2801 And 1760 With Monitoring Software Called Zenoss?
Sep 4, 2011I am trying to monitor routers Cisco 2610, 2801 and 1760 with a monitoring software called zenoss. and I cant see on this devices the powersupply state, temperature sensor, fan state, i dont know if this models of routers cant support the monitoring of this component on the devices.what can i do to monitoring this component? what kind of Oid I can use to get this components state?
View 4 Replies View RelatedLinksys Wireless Router :: E2000 Cisco Software And Router Password?
May 4, 2013I have an e2000 wireless router. I have the latest software version for the Cisco software.I have noticed that Cisco sets up the same password to access the router setup page as the wireless password..Anyone that connects to the main SSID will be able to connect to the setup page at 192.168.1.1...I know that I can change the password in the linksys setup page to whatever I want, but then when I open the Cisco software, it wants me to change the password to match what the administrator password is.Don't they realize that a wireless password is different than the Administrator password to access the router settings?
View 5 Replies View RelatedCisco Switching/Routing :: Router Boots Into Router With 2500 Series
Jul 27, 2009I m having 2500 series router. when i boot router automatically get into router(boot)> . how to solve?
View 6 Replies View RelatedLinksys Wireless Router :: E1200 When Run Cisco Connect After Couple Minutes Searching / Can't Find Router
Mar 9, 2012I want to use cisco connect with the Router E1200. There is a wireless connection between laptop and E1200 Router. When I run the "Cisco Connect" after couple minutes searching It can not find the Router and I have to put an (Router name SSID) and password.
View 9 Replies View RelatedCisco VPN :: 7100 VPN Router To Vigor Draytek 2820 VPN Router?
Apr 19, 2011I have managed to get the tunnel up and working and we are sending data via the tunnel from our Cisco VPN router to the Draytek and onto the clients server. (they , the client, have acknowledged that they are recieving and sending packets back to us).But, we never see any returning packets at our VPN tunnel endpoint. When we send I see the encrypted packet count go up , but the packet decrypt remains at zero, this is using show crypto ipsec sa | begin x.x.x.x.
We do have other working VPN solutions, but this is the first connecting to a Draytek. The ACL's are matching, and they have NAT turned off. The routing is fine or else the tunnel would not come up as are all the tunnel parameters, else our packets would not arrive at their server.
Cisco VPN :: 2900 Router / One Hub Router And 3 Spokes - DMVPN Error
Jun 21, 2012I configured dmvpn at cisco router 2900. one hub router and 3 spokes. all of them are working normally but tomorrow i see one error at at one spoke router.
error:
Maximum Tx Bandwidth limit of 85000 Kbps reached for Crypto functionality with securityk9 technology package license