Cisco VPN :: 7100 VPN Router To Vigor Draytek 2820 VPN Router?
Apr 19, 2011
I have managed to get the tunnel up and working and we are sending data via the tunnel from our Cisco VPN router to the Draytek and onto the clients server. (they , the client, have acknowledged that they are recieving and sending packets back to us).But, we never see any returning packets at our VPN tunnel endpoint. When we send I see the encrypted packet count go up , but the packet decrypt remains at zero, this is using show crypto ipsec sa | begin x.x.x.x.
We do have other working VPN solutions, but this is the first connecting to a Draytek. The ACL's are matching, and they have NAT turned off. The routing is fine or else the tunnel would not come up as are all the tunnel parameters, else our packets would not arrive at their server.
View 1 Replies
ADVERTISEMENT
Dec 17, 2011
I have recently changed my Router to a Draytek Vigor 2830N from the standard O2 broadband router. When I swap them out I get no internet access via the main PC that is connected via ethernet. However I can access internet via WLAN on any other device. here are the ipconfig details for before and after swap (same)
View 3 Replies
View Related
Jul 14, 2011
I am currently using a Draytek 2820 at work and I am needing to port forward port 3333 to two different computers at the same time
View 9 Replies
View Related
Mar 17, 2013
I have a 7100 router that has some servers behind it. I need to translate each server to a public IP. The only thing is that between the outside world and the router is an ASA. We have a small data center where the ASA is connected to a core switch on the inside and the ISP on the outside. How would I do the NAT/PAT translations on the 7100 and then have them pass through the ASA? for example:
View 6 Replies
View Related
Sep 27, 2012
We have a Vigor ADSL modem linked to a hub that then links to 3 pc's and 2 printers all via ethernet. Connection to the outside world is fine.
A few weeks ago the IT geek decided to switch the modem from DHCP to PPPoA and put each pc & printer on fixed IPs. The Vigor is also on a static IP.
This therefore cut off our link to the Linksys WRTG54 we have in a different room serving as a wireless router.
The Linksys is/was connected via ethernet to port 1, port 2 direct to laptop. Wireless worked fine until they changed to static IP etc on the Vigor, now we only have ethernet to the laptop and no Wireless.
What do we need to do at the Linksys end to get wireless working again?
View 9 Replies
View Related
Feb 1, 2013
I've set up PPPoE on my EA4500 router with a Vigor 120 modem in bridged mode and it says an internet connection is established, but the connection is extremely slow on all my devices. When I run the speed test within the EA4500 firmware it appears fine, but I cannot load any web pages on my laptop or other decives because the connection is so slow. The connection is slow with both wired and wireless connections. I've tried changing the MTU settings with no success. I've also tried using a different router and connecting the modem directly to my laptop and using PPPoE within the laptop and these both work fine, so I think it's clear there is a problem with the EA4500 router itself.
I'm just using the Vigor 120 to authenticate and connect to the internet itself, with the router in DHCP automatic configuration mode. I think this is causing a double NAT.
View 9 Replies
View Related
Jul 13, 2011
I have a cisco 877 router connected to our adsl broadband at our head office. I have managed to set this up with Nat and DHCP all working to let multiple users access the internet through our single static ip supplied by the ISP lets say the ip is 1.2.3.4.Our internal network is 192.168.1.0 255.255. 255. 0.I have a draytek vigor 2600 at a branch office set up the same with a static ip addresss supplied by the ISP lets say the ip is 5.6.7.8.The internal network is 192.168.4.0 255.255.255.0
I am trying to set up a VPN between the head office and branch office so the branch office users can connect to our internal server(lets say ip is 192.168.1.2) to receive group policies,access files and also telnet into our database server(lets say ip is 192.168.1.3).I have attached a sort of running config that i have pieced together from bits i have read on this site and others. I have tried these settings and other permutations of these settings but i cant seem to establish a tunnel even though when i show int tunnel0 on the router it says tunnel is up and line protocol is up, if i show ip route it shows that there is an ip address for the tunnel and that is about it(No vpn light on).
If it makes sense and that I have entered the right information? I have highlighted the parts i am not sure about in red(Quite a bit and obviously not the exact settings but what i think it should be). Once all the settings are correct on the cisco will it automatically establish the vpn or do i have to dial it from the draytek.
View 4 Replies
View Related
Jun 26, 2011
My company is setting up a small branch in Scotland (the main office is in Bristol)All we need one desktop, one laptop, a printer and we will be using a DraytekVgn router, and a small switch.We need VPN to this office to set up an inhouse application.How would I set this up with minimal configuration.......ie...Does BT send a router/modem with the set up..Is there anything inside the router configuration that has to be changed.(I know PPTP etc has to be enabled).Do I use the same vpn external ip address we use for our other 2 branches....Can I change the IP Address of the router from 192.168.1.1........to say 192.168.100.1.
View 6 Replies
View Related
Jun 19, 2011
my local site has Cisco 2811 router connecting locally to ASA 5520. Remote site A has Draytek Vigor2950. I have working vpn between local subnet 10.0.0.0/24 and remote site A 10.100.6.0/24. I have remote sites B (10.100.7.0/24) and C (10.100.8.0/24). I would like to route traffic from local site to remote sites B and C via the local-to-remote A vpn. On Draytek routers B and C, I have added to subnet 10.0.0.0/24 to the remote network profile list. On local router, I route traffic for subnets 10.100.7.x and 10.100.8.x to the ASA. On ASA I have added these subnets to the profile for local-to-remoteA vpn.But the vpn will not establish when I attempt to ping from local to remote B or C.
View 5 Replies
View Related
Jun 14, 2011
I'm having some rather odd issues with my wireless connectivity. Running a draytek 2830n router. The wireless connection drops out at random sometimes, at other times it connects (shows full reception) but does allow any kind of internet connection. Plugging in by lan cable allows normal function.I have no clue whats going on but I did just notice that shutting down one of the laptops connected to the network (Dell lx502) appears to have solved the problem for the moment. I've not had a chance to test this as a long term solution. However I believe this is the only laptop with a dual band wifi card.This problem was also occurring on our previous router, a draytek 2820vn but the symptoms were a bit different and this laptop was not there at the time.Is it possible for one machine to knock out an entire wireless network? The other change I made yesterday was to activate the bind ip to mac function on the router for our new NAS as I was messing around with ftp configurations.
View 1 Replies
View Related
Mar 9, 2011
We have a Cisco 2820 that serves as a hub and our spokes are Cisco 871s. Its been working for a while and for some reason last week. Http and https traffic over the tunnel is having connection issues. I can Remote desktop or PCanywhere into the remote PCs. From that PC I can ping internal IP address or IP of the webmail server or internal webserver with no issue. But if I access it over the browser it times out or it will work and stop working again. Basically ica, icmp, pcanythere, rdp traffic works over the tunnel but not http or https.
View 2 Replies
View Related
Aug 9, 2012
It was fine, online games like ARMA2 and Everquest2 worked w/o fail (for hours and hours).
My son went to get on one day and the ARMA game would let him sign in, then drop him. I told him it was the game as it is a bastardized program from several programmers and i just assumed it was a software issue. Then I decide to get on Everquest2 and it does the same thing to me, you log in, you get started and 1 min later in drops you. Both his game and mine give you a "server not found" error even when you were just online and playing. Everquest even starts looking for "log in servers" 1-6 and fails on all. I can log off and get right in again, but only for 1 to 2 min. then dropped.
My other internet connections work fine. Sony PS3, no problems....my wifes Dell laptop, no problems, my other Dell (while playing ARMA2 and Everquest2) no problem.
Product
Studio XPS 7100
BIOS Version String
[Code].....
View 3 Replies
View Related
Jan 15, 2012
I just recently learned that my Kodak ESP5250 printer needs to be installed with the Wi-Fi in my Windows 7 Ultimate SP1. How do I activate the Wi-Fi installed in my Dell Inspiron 7100?
View 1 Replies
View Related
Nov 4, 2012
I did a clean install of windows 8 and my tooth application or drivers do not show up in device manager dell xps studio 7100.
View 1 Replies
View Related
Mar 26, 2012
I've recently installed a Cisco ASA with a NAT'd configuration, I'm in the final stages and would like to configure a lan to lan VPN to a Draytek box and that unfortunately isn't going well and having spent almost two days on it am starting to wonder if it will actually work. I can get it to connect but no data seems to be transmitted between the two.
Site A on the range 10.0.0.0 has the ASA and Site B is on the 192.168.16.0 and is a Draytek 2930.
Below is the ASA config created with the lan to lan wizard:
route outside 0.0.0.0 0.0.0.0 193.164.x
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00(code)
View 1 Replies
View Related
Jun 27, 2011
We're trying to establish a "simple" vpn tunnel between a cisco 800 and a draytek 2910, situation:
LAN (192.168.2.0 ) --cisco800 ----- internet ------ draytek ----LAN (192.168.20.0 )
WAN-ports , internet access on both sides are working fine.vpn configuration part cisco:
crypto isakmp policy 1
encr 3des
authentication pre-share
group 2
[code]....
What can be wrong: other protocol? something with pfs? diffy hellman group: i heart draytek used 1 and cisco 2?debugging on the cisco site keeps on ginving the error message:
entry number 487 : CRYPTO-4-IKMP_BAD_MESSAGE
IKE message from x.x.x.x failed its sanity check or is malformed
timestamp: 4002880
View 5 Replies
View Related
Apr 20, 2011
I have a Cisco 7200 and need to establish L2TP over IPSEC session with a Draytek Fly200. Draytek must use L2TP over IPSEC to provide LAN-to-LAN connectivity. IPSEC phase 1 and 2 is ok, L2TP tunnel is also established, but on cloned virtual-access IPCP negotiation is not completed:
*Sep 16 09:50:36.911: %LINK-3-UPDOWN: Interface Virtual-Access3, changed state to up
L2X_ADJ: Vi3:midchain adj reqd for ip 0.0.0.0, cid 0
*Sep 16 09:50:38.911: Vi3 IPCP: O CONFREQ [REQsent] id 2 len 10
*Sep 16 09:50:38.911: Vi3 IPCP: Address 192.168.176.2 (0x0306C0A8B002)
*Sep 16 09:50:38.911: Vi3 IPCP: Event[Timeout+] State[REQsent to REQsent]
I think my VPDN configuration from Cisco side is not correct, but I cannot find configuration examples for this kind of solution.
View 8 Replies
View Related
Apr 11, 2013
we have bought 2 Draytek 2830 Routers for our 2 businesses that are in different locations. We are looking at setting up a VPN between them and wanted to do it similar to the following:
http:[url].....
The thing the "Dial IN" site has a static IP from the ISP but the "Dial Out" site has a dynamic IP.what the best approach to take with this would be as I guess the link between the routers wouldn't work if the address kept changing?
View 2 Replies
View Related
Sep 18, 2012
Any experience with IP Routing on Draytek routers?We have a 2830 and I'm trying to set it up like the following: [code]
Now a server in VLAN 2 with address x.x.x.77 can ping x.x.x.74, but I can't access any of it's services (Apache, SSH etc) from the internet (testing through my phone and other people).I've removed the IPs from the NAT pool in the WAN settings, setup LAN2 for IP routing and put it into the second VLAN, but apart from that not done much else.
View 3 Replies
View Related
May 4, 2013
I have an e2000 wireless router. I have the latest software version for the Cisco software.I have noticed that Cisco sets up the same password to access the router setup page as the wireless password..Anyone that connects to the main SSID will be able to connect to the setup page at 192.168.1.1...I know that I can change the password in the linksys setup page to whatever I want, but then when I open the Cisco software, it wants me to change the password to match what the administrator password is.Don't they realize that a wireless password is different than the Administrator password to access the router settings?
View 5 Replies
View Related
Jul 27, 2009
I m having 2500 series router. when i boot router automatically get into router(boot)> . how to solve?
View 6 Replies
View Related
Mar 9, 2012
I want to use cisco connect with the Router E1200. There is a wireless connection between laptop and E1200 Router. When I run the "Cisco Connect" after couple minutes searching It can not find the Router and I have to put an (Router name SSID) and password.
View 9 Replies
View Related
Jun 21, 2012
I configured dmvpn at cisco router 2900. one hub router and 3 spokes. all of them are working normally but tomorrow i see one error at at one spoke router.
error:
Maximum Tx Bandwidth limit of 85000 Kbps reached for Crypto functionality with securityk9 technology package license
View 1 Replies
View Related
Oct 25, 2012
I have a CISCO 851W router in the garage that I want to connect to my Linksys router in the office, which is connected to the internet.The 851W is connected from it's WAN port to Lan port 1 of the Linksys router. Now, currently that ethernet cable is a straight-through cable. Does it have to be crossover? If so, I can fix that.
I want the default gateway for the CISCO router to be 192.168.2.1. I am not sure how to configure that. [URL]
View 3 Replies
View Related
Dec 28, 2012
I have two mac laptops and am trying to copy a directory with a number of PDFs in it. The files aren't particularly large, but there are many of them. At some point in the process the router stops and must be turned off and on before it will respond again either wirelessly or wired. I have tried the same experiment with both devices wired and the router works fine. I have tried changing the MTU, channel, beacon setting, etc. as other forum posts have tried. I tried reflashing the firmware, resetting to factory defaults and reconfiguring. So far no success. Cisco support wants me to return the router. Frankly I'm at the point of considering the former Linksys/Cisco products complete rubbish. I am going to have to buy a new router even if I return this one since I can't be without a router for any length of time.
View 8 Replies
View Related
Jan 4, 2011
Why there is no parental control feature built in for WAP610N... how do i block website on all computers connected to my router?
View 4 Replies
View Related
Aug 9, 2012
We have a home use WRT160N router linked to a PC desktop and two wireless laptops, Yesterday bought a new I-Phone, but could not link to my network (entered the security key many times). I accidentally connected to computer fix it firm that linked to my PC and wanted a large sum to fix the problem which he said was due to large number of temp?? internet files and once removed he would change the IP address of the desktop computer? Is this diagnosis logical and can I do it on my own. The router is definetely working - both laptops access the internet and I was recently able to hook up a Samsung Blu-Ray player using the same security code I used for the I-Phone.
View 1 Replies
View Related
Mar 18, 2012
Is the Linksys E4200 Dual Band Router compatible with DHCP and VPN?
View 1 Replies
View Related
Mar 5, 2013
The router had firmware 2.0.x(?) and I tried to update to the latest FW, according to the webpage that's
FW_E1000_2.1.02.006_US_20130115.bin
Hardware is E1000 v2 according to sticker on back.The firmware update failed (no reason given) and the router now hangs in limbo where all it does is flashing the power LED.I set my PC to 19?2.168.1.2 and TFTP'd the firmware over to 192.168.1.1 - no errors reported and 192.168.1.1 is pingable. Held reset for 30s, then powered down the router for another 30s. On power-up the router still flashes the power LED.
View 3 Replies
View Related
Jun 26, 2012
I installed an IP camera, and had to change my E1000 router settings to a static IP address. Now I can't access the router settings. 192.168.1.1 is still the default gateway, but it won't open in any browser.
I'm reluctant to do a reset because it took me quite a while to figure out how to get the IP camera and port forwarding working (it does!), and I'd hate to do it all again and come to the same place. I'm not very good at this stuff, and it's a small miracle that I did it once.
View 4 Replies
View Related
Aug 27, 2008
Can you use your WRT54G router with the newer WRT310N router to extend your wireless signal? How?
View 7 Replies
View Related
Apr 6, 2012
The standard Verizon router doesn't have Wireless N capability, so I got the WRT600N (first floor) a while back and connected it to one of the ports on the Verizon router (basement). I have the wireless turned off on Verizon router. My problem is that anything connecting to the WRT600N has extremely intermittent connectivity.
View 1 Replies
View Related
Jun 20, 2010
I just got E1000 cisco wireless router. Started setup, everything worked fine and replaced admin password with my own. For some reason got error message. tried to redo setup and got message router not recognized. used laptop and found out that wireless works fine. After few days noticed that there is a (mynetworkname) guest connection you can connect without any password. i don't need that stupid thing and my question is how to disable guest network? I cannot reach Main Menu from cd and have no idea where to look for it when i connect to router by web.
View 9 Replies
View Related