Cisco Switching/Routing :: Router Boots Into Router With 2500 Series
Jul 27, 2009I m having 2500 series router. when i boot router automatically get into router(boot)> . how to solve?
View 6 Replies
ADVERTISEMENT
Cisco Switching/Routing :: 2500 To Show The DHCP Range Of Router
Jul 29, 2012how can I show the DHCP-range of a router if I don't have privilege level? (not in enable-mode),I can do a "show ip dhcp pool" - this will show me the range which is configured with the network-command.But there are also some dhcp-exclude-addresses which I can't see.... (I did a test on a router with full privilege-access)I need this because I have a router with limited access from our provider.
View 0 Replies View RelatedCisco :: Does WLC 2500 Series Supports 1262 Series Access Point
Jun 14, 2011Does AIR-CT2504-25-K9 spupports AIR-LAP1262N-E-K9 Access Point? How can I check this?
View 1 Replies View RelatedCisco Switching/Routing :: 3500XL Switch - Does Not Load Flash Or Boots
Dec 8, 2011Base ethernet MAC Address: 00:0a:b7:07:35:80Xmodem file system is available. The system has been interrupted prior to initializing theflash filesystem. The following commands will initialize the flash filesystem, and finish loading the operating system software:
flash_init load_helper boot switch: flash_initInitializing Flash...flashfs[0]: 3 files, 1 directoriesflashfs[0]: 0 orphaned files, 0 orphaned directoriesflashfs[0]: Total bytes: 3612672flashfs[0]: Bytes used: 1815040flashfs[0]: Bytes available: 1797632flashfs[0]: flashfs fsck took 3 seconds....done Initializing Flash.Boot Sector Filesystem (bs:) installed, fsid: 3Parameter Block Filesystem (pb:) installed, fsid: 4ô
Cisco Switching/Routing :: 6509 / 720 Sups Random ROMmon Boots
Dec 27, 2012Got a long lingering, year long issue that has spanned about 8 supervisor cards and a complete chassis swap. The 6509 acts as a ITN in our facility. The active sup card at random points of pipe usage boots into rommon mode, seriously inhibiting our company. I'm able to swap the 2 fiber pairs that we had going into the active supervisor card into the secondary and usually this works for another random amount of time, however, today it occured within minutes of hooking up the fiber links. Sitting there for about 5 minutes it booted into ROMMON. When this happens, I'm able to boot the sup card back to good status. Previous remedial actions, other than replacing sup cards/chassis, was checking the config register and making sure it was x2102. Previously, it was not, and we corrected and reloaded and it took, we thought this would fix the problem, until today.
[code]....
Cisco Switching/Routing :: 5548 - Restore IOS When Switch Boots Into Loader?
Apr 3, 2013I was in the process of recovering a password on a nexus 5548 swith when it finally gets in to the boot mode.I think i lost all my bootloader code.How do i get it back on the switch
loader> load n5000-uk9.5.0.3.N2.1.bin
Error 27: Unrecognized command
how to restore my IOS on this device
Cisco Switching/Routing :: 6509 Redundant Sup720 - Slave Boots Into ROMmon
Oct 24, 2012I'm fairly new to networking and need to migrate an old core to a new core. I have a 6509-e Switch that I had an RMA on one of my 720 sup cards. After receiving the sup card I swapped my slave out with the new one, expecting it to boot into ios. It booted into Roman. I tried to boot the image manually and it did the same thing. I also tried to boot from my flash and, again, booted into ROMmon.
Question: If i configure and change the boot to boot from image it tells me i need to reset or power cycle first. Will this reset the entire switch? As this is production I'd rather not.
I am at home now, but I can supply any logs/hardware model/configs tomorrow. I thought I would see if this is an easy fix.
Cisco Switching/Routing :: 800 Series Router Configuration
Jun 13, 2012about to install first UC320w and wanted some sample 800 series router configurations showing required port fowarding, ACL entries and QoS examples.
View 5 Replies View RelatedCisco Switching/Routing :: Setting Up NAT On 800 Series Router
Aug 23, 2012I have a Cisco 800 series router that I need to set NAT up on. There will be four computers connecting to the internet through it. I already have the IP address coming from my cable modem I just do not know the command to get it to translate to my internal dhcp pool I have setup.
View 1 Replies View RelatedCisco Switching/Routing :: NATing On 2800 Router Series
May 22, 2013I have Router 2800 series Global nating is configured on it.
ip nat inside source list 111 interface Dialer1 overload
!
access-list 111 deny ip 192.168.1.0 0.0.0.255 192.168.0.0 0.0.0.255
access-list 111 permit ip 192.168.1.0 0.0.0.255 any
My object is that i want give internet access only for few users ip E.g IPs addresses from range 192.168.1.0-10 can acess intenet access other all are deny.How i do this with ACL .
Cisco Switching/Routing :: Setup RDP To A Server On 800 Series Router
Dec 27, 2012I would like to setup RDP on my cisco router so I can access my server from outside my network. I also have a router from my ISP that has DHCP for my external IP address and DHCP for my internal as well.
View 3 Replies View RelatedCisco Switching/Routing :: Setting Up NAT And Possibly PAT On 800 Series Router
Aug 23, 2012I have a Cisco 800 series router that I need to set NAT up on. There will be four computers connecting to the internet through it. I already have the IP address coming from my cable modem I just do not know the command to get it to translate to my internal dhcp pool I have setup. I have also been doing some research, seeing as I only have one public IP address coming from my ISP will I have to use PAT as well?
View 1 Replies View RelatedCisco Switching/Routing :: Can't Configure SPAN On 800 Series Router
May 1, 2013I have a Cisco 881 router running 15.1(4)M4. I am trying to configure SPAN on it to mirror my outside interface (source) to one of my LAN interfaces (dest).
!--- WAN interface
interface FastEthernet4
description Comcast WAN$ETH-WAN$
[Code]......
As you can see from the above output there is a problem with the command on this interface. When I try to set Fa0 as my source it works fine:
rtr(config)#mon session 1 source int fastEthernet 0
rtr(config)#
Is this because fa4 is layer 3 and fa0 is a switchport? If so, is there another way to set fa4 as the source?
Cisco Switching/Routing :: 2600 Series Router Cannot Remember PW
Mar 28, 2012I have a 2600 Router series and I cannot remember the Password. I have tried following web pages that state to use control Break on the boot up but its not working.can reset that pw and write erase my configuration file?Here is my boot up. I have tried hitting control break at the very beginning over and over and then again when at the cold boot it has not worked....
System Bootstrap, Version 12.2(7r) [cmong 7r], RELEASE SOFTWARE (fc1)Copyright (c) 2002 by cisco Systems, Inc.C2600 platform with 131072 Kbytes of main memory
program load complete, entry point: 0x80008000, size: 0x1c9468cSelf decompressing the image : ######################################################################################################################################################################################################################################################################################################################################################################################################################################################################## [OK]
Smart Init is enabledsmart init is sizing iomem ID MEMORY_REQ TYPE00036A 0X000B3B80 C2610XM Single Fast Ethernet 0X00098670
[code]....
Cisco Switching/Routing :: 3900 Series Router Licensing?
Feb 6, 2013Can the 3900 series router be ordered or upgraded to a license with advances enterprise services? I have a few of these routers and I'm looking to get the license upgraded if possible.
View 1 Replies View RelatedCisco Switching/Routing :: Setup Port Forwarding On 800 Series Router?
Jan 14, 2013I just setup my homelab today, after having Cat5e installed so I can run my servers and network equiptment over wired network as well as setting up a wireless system. I got everything setup and its going great I can access everything from my office now including a E4200 Linksys router that I setup to do RiP (was only choice pretty much, or NAT), and my 891 Cisco Router which is my internet connection.
I use to have the linksys setup to do port forwarding but now I need to figure out how to do it on the cisco 891 router via command line.
Below is my current configuration. I need to be able to access my server which is behind my router by Remote Desktop. I also have a web server, and the kids also play minecraft, and have a server setup so I need to be able to forward their port as well.
[URL]
Ths is from the link above, would I just do like that but then put in my IPs and is that my Private IP I use this or my public facing. Also he has "interface Dialer1 6881" again after the port in the second and third row. I dont really understand what they have there. I understand basic access list and such though I am extremely rusty.
!
ip nat inside source list 102 interface Dialer1 overload
ip nat inside source static tcp 10.0.0.2 6881 interface Dialer1 6881
[Code].....
Cisco Switching/Routing :: Module To Add Gig Interfaces To 2800 Series Router
Aug 16, 2012I am trying to add WCCP to be configured for websense. My first option seems to be either purchase an IPServices license for the stack of 3750E switches, but i am thinking this will require us to license all three switches in the stack. The second option i am looking at is to do the WCCP configuration on the 2800 router we have on the edge. The problem is both Gig ports are in use, one going to the firewall and the second going to the ISP. My first question would be, which option is better in terms of manging as well as cost of implementing it.The second question is, if WCCP on the router is a better option, what is the add on module i should be looking to get to add the additional ports to hook up the Websense cache.
View 8 Replies View RelatedCisco Switching/Routing :: 1900 Series Router Not Giving Out IP Addresses
Oct 15, 2012I've got a problem with DHCP running on a cisco 1900 series router, 1921 to be precise. The Data VLAN works perfectly, i configured a ip helper address and its working. Problem tough is VLAN 20. This is the voice vlan. As u can see in the config below, this has been configured using VRRP and VRF for failover purposes. I did more of these configurations, and they all worked fine, just not with this particular router!
As u will notice i deleted all the not needed to know information or i X'ed it!
Jan-Aart
version 15.1
service timestamps debug datetime msec
[Code]......
Cisco Switching/Routing :: Recover Username And Password For 870 Series Router?
Jan 20, 2009how do i recover username and password for 870 series router
View 5 Replies View RelatedCisco Switching/Routing :: Router 800 Series Interface Cellular0 Keeps Bouncing Up / Down
Aug 6, 2012I was able to setup my router c819 with Verizon 3G but there is one minor thing that on the console it keeps saying:
Aug 7 21:04:30.067: %LINK-5-CHANGED: Interface Cellular0, changed state to reset
Aug 7 21:04:35.111: %LINK-3-UPDOWN: Interface Cellular0, changed state to down
Aug 7 21:06:18.423: %LINK-3-UPDOWN: Interface Cellular0, changed state to up
The interface Cellluar0 is connected to Verizon 3G network and I'm able to ping and get to the internet just fine. I did few research and some people said it was access list. My ACL is below but I can't find anything wrong with it.
!
!
interface Cellular0
ip address negotiated
[Code].....
Cisco Switching/Routing :: 887 - How To Restrict Devices Connected To 800 Series Router
Jan 30, 2013I have a Cisco 887M router which I wish to restrict the devices allowed to be connected/allocated an IP address to two, and *only* two.
I can't, for the life of me, find out how to allow these two devices to connect to ANY port - I can configure a MAC restriction on a single port, but I don't know how to make it so that I can allow JUST these two devices to connect to any port in the 4 port switch/VLAN (VLAN 1 is used because the mongrel who set this up was lazy). I know the MAC addresses I want to allow
How I can do this? I *can* restrict any given port to the two MAC addresses - but if I try to add the MAC addresses to another port, they get removed from the initial one. I need to be able to have them connect to ANY port and work, but allow NOTHING else to work.
For those wondering, this is to counter a user who is utilising company resources for purposes not approved - and costing us quite a bit of money in the process.
Cisco Switching/Routing :: 1941 Series Router Stopped Responding After Restart
Aug 12, 2012I am setting up a Cisco 1941 series router for our department in Denmark. As we quickly relised we had to reset the router to it's defult settings. As we comunicated with the router thorugh HyperTerminal, the router asked me to restart. After we did so the router only sends encrypted messages wich is unreadable. We neither get any respons in the terminal when we try to write commands back to the router.We have tried to use different terminal programs as well as the USB port on the router.
View 4 Replies View RelatedCisco Switching/Routing :: Copy Startup Configuration From 877W To Another 870 Series Router?
Jan 4, 2012I have an 877W router that I would like to have a 2nd pre-configured backup for. I was thinking of getting another 870 series (probably an 877) router, as the more expensive wireless option is not actually required. Am I right to assume that I could simply copy the contents of my current config.txt file onto the second router?
View 4 Replies View RelatedCisco Switching/Routing :: Get Fiber Optic Modules For 2821 Series Router
Mar 20, 2012How to get fiber optic modules for Cisco 2821 series router. I can not find anything apart a SFP module which contains only one SFP port.
View 9 Replies View RelatedCisco Switching/Routing :: 1900 Series Router Needs Reboot Every Time Connection Is Lost
Jan 1, 2013i have a cisco 1900 series router from the isp and we connect it the our router the rv042 small biz, and we have here a cisco catalyst 2950 switch with just default configuration connected to the hosts.
my problem is from time to time that the connection is lost there is no connection with the router and the only solution is to turn off and on the cisco 1900 router and the connection will be back.
do we need to configure the routers and switches? what do you need to configure?
Cisco Switching/Routing :: 2800 Series Router - Multicasting Windows Deployment Services
Mar 25, 2012We have recently implemented Windows Deployment Services on our local network, but everytime we do a multicast image deployment the network get flooded to point of total saturation.
We have Netgear switches and a Cisco 2800 series router. IGMP Snooping has been enabled on all Switches, however, we are unsure on how to implement multicasting on the router.
The whole network is flat - no VLANs over than the default VLAN1. We only want multicasting to work within our local network and does not need to go out the other side of the router as that is the connection to the internet.
How to get the Cisco router configured properly to enable multicasting to not flood the network. It seems that even if we were to image 4 PCs using multicast this is enough to completely get the network flooded.
Also, am I right in thinking that IGMP needs to be enabled on all of the Switches?
Cisco :: WLC 2500 Series / Differences Between 7.0 And 7.2 Firmware?
Mar 28, 2012which differences exist between 7.0 and 7.2 firmwares? I have to decide/choose which of them to run, before continuing to configure my WLAN infrastructure.
View 3 Replies View RelatedCisco :: WLC 2500 Series URL Filtering And Hotspot?
Oct 2, 2012I have Cisco Wireless Controller 2500 series (AIR-CT2504) and 10 LAPs implemented in my office building. I need to enforce security policy.
I have few questions below regarding the Wireless controller 2500 Series.
1) Can i enforce Internet security policy such that all prohibitive sites remain block from the WLC?
2) Is it possible to allow Internet access to only designated machines/users ?
3) Initial logon page for user /machine authentication to get access to wi-fi ?
Cisco Wireless :: MIBs For 2500 Series WLC
Apr 25, 2012I need the MIBs for Cisco 2500 WLC. I have it for 5508 WLC. Does it works same for 2500 WLC too ?
View 1 Replies View RelatedCisco Switching/Routing :: 2800 Series Router - Removing And Installing Compact Flash Memory Cards
Nov 15, 2011I just read the Removing and Installing CompactFlash Memory Cards in Cisco 2800 Series Routers instructions and there was nothing said regading powering down the router. Are these CompactFlash cards hot swappable??
View 2 Replies View RelatedCisco Wireless :: 2500 Series Machine Authentication With IAS
Jun 2, 2013I have the problem with machine authentication, our customer using Wireless Controller 2500 Series and need implement machine authentication on IAS server. So, as my understand is our controller may not change anything with configuration but we may configure IAS for support machine authentication, correct? but my question is how to? and is it work ?
View 24 Replies View RelatedCisco Wireless :: 2500 Series WLC Crashed Repeatedly
Aug 11, 2012I have 2500 series wlc which is crashing again and again. I attach the log of crash as well.Also in License location the base-ap-count license " is not in use ".
View 3 Replies View RelatedCisco Wireless :: 2500 Series Support Mobility Groups?
Dec 1, 2011Do you know if the new 2500 series controller supports things like mobility groups? Could I use 2 of these and do inter-controller roaming. Also do you know if this would work with a 2106 controller and a 2505 controller or are they 2 completely independent controllers only knowing about their own APs??
View 12 Replies View Related