Cisco Switching/Routing :: 2600 Series Router Cannot Remember PW
Mar 28, 2012
I have a 2600 Router series and I cannot remember the Password. I have tried following web pages that state to use control Break on the boot up but its not working.can reset that pw and write erase my configuration file?Here is my boot up. I have tried hitting control break at the very beginning over and over and then again when at the cold boot it has not worked....
System Bootstrap, Version 12.2(7r) [cmong 7r], RELEASE SOFTWARE (fc1)Copyright (c) 2002 by cisco Systems, Inc.C2600 platform with 131072 Kbytes of main memory
program load complete, entry point: 0x80008000, size: 0x1c9468cSelf decompressing the image : ######################################################################################################################################################################################################################################################################################################################################################################################################################################################################## [OK]
Smart Init is enabledsmart init is sizing iomem ID MEMORY_REQ TYPE00036A 0X000B3B80 C2610XM Single Fast Ethernet 0X00098670
[code]....
View 4 Replies
ADVERTISEMENT
Feb 14, 2012
does Cisco 2600 series switch support 802.1x and DHCP snooping?
View 6 Replies
View Related
Dec 6, 2010
I am asked to implement the security in campus Network. i.e. In this network we want to block some websites, We don't want to use any 3rd party software or proxy server and content filtering module to block theset.my router IOS is advance securityk9 How to block the website in a Cisco 2600 series router by using the command. What is the access list we need to use to block.Assume we want to restrict,
[URL]
Here we are using Cisco 2600 series router and 2900 series switch. In router we are using the2Mb lease line link
View 6 Replies
View Related
Oct 31, 2012
How to configure HSRP in techroutes 2600 series router and aaa authentication
View 2 Replies
View Related
Jun 26, 2012
We are upgrading our incoming Internet service from 30 Mb 10/100 to 100Mb 10/1,000.Will my 2600 series router support the 10Mb 10/1,000 traffic from my new modem?Do I need to change my interface speed from 100 to 1,000? I to be sure my router will support the upgrade. [code]
View 8 Replies
View Related
Oct 25, 2012
I am connecting a 2600 router to an ISP. Interface 0/0 is connected to the ISP using DHCP. Interface 0/1 is connected to the inside providing DHCP services to the inside. At least it should only be providing DHCP services to the inside. I also have a public static IP that is NAT to a private static IP. Everything is working except the computer on the static IP. From the router I am able to ping inside and out from each interface. I am able to ping both interfaces of the router from the computer on the static IP but I cannot ping outside the router. If I do a debug all I see a reject for the gateway of the static IP but it has “mobile IP” in the text string. Not sure what mobile IP is relating to. Networks are as follows:
0/0 DHCP 10.X.X.X
0/1 192x.x.x
Static 75.X.X.X
no ip dhcp use vrf connected
ip dhcp excluded-address 192.X.X.1
ip dhcp excluded-address 192.X.X.2
ip dhcp pool CLIENT
[code]...
View 2 Replies
View Related
Jul 8, 2012
I have a 2600 router and im trying to set it up for SDM. The crypto command is not there. What do i do?
show version
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-J1S3-M), Version 12.3(15b), RELEASE SOFTWARE (fc1 )
Copyright (c) 1986-2005 by cisco Systems, Inc.
Compiled Thu 25-Aug-05 13:38 by ssearch
Image text-base: 0x80008098, data-base: 0x81A255C4
[code]....
View 3 Replies
View Related
Jan 24, 2012
I have a cable modem with my 2600 Router and i have a little speed problem when I'm going out to the web via my F0/0.. according to regular speed test sites my speed is around 20mbps but when i hook up to my modem directly i get a solid 40mbps.. now I've changed my Cat 6 cable from my modem to my router and this are my settings in the router.
[Code] ...........
I see some drops and lost carriers but not sure what those might mean?
View 2 Replies
View Related
Apr 28, 2013
- How can I connect an old 2600 router to a linksys WRT54G2. to access the internet. I think it is not possible
- What device do i need to be able to do it
View 5 Replies
View Related
Aug 30, 2012
I have been saving money to build my ccna voice lab. Recently I bought 2600 and 1700 series routers.One of the 2600 router needed a password recovery so after a refreshing nap i got to work.
During the password recovery procedure, I mistyped confreg 0x1242; by the time I realized my mistake, my computer screen was full of "C" characters Now the whole story is i can not console into it.
Edit:After some research, I found If I use the baud rate 1200 in hyperterminal.i will be able to console into it.When I did that, I noticed that Rommon kept incrementing as:
rommon 1 >
rommon 1 > confreg 0x2142
rommon 2 >
rommon 2 >
rommon 2 >
rommon 2 >
rommon 2 > confreg 0x2142
rommon 3 >
View 4 Replies
View Related
Jun 27, 2012
I recently lost my configuration when attempting to reset the password for our Cisco 3560g switch, the switch connects to a Cisco 4506 switch via fiber back to our main office.
I have the switch temporarily routing all traffic to our 4506 by using the default route of 0.0.0.0 0.0.0.0 10.10.10.254 but the same switch is connected to a cisco 2600 router that is on a 10.10.20.0 network and the 3560g is on a 10.0.0.0 network.
Host computers sit on the 10.0.0.0 network, but they need to go to the 10.10.10.0 network for internet, domain, etc the same computers need to go to the 10.10.10.20 for remote connections and other services.
The address of the 3560g is: 10.0.0.254
The address of the 2600 is 10.10.20.2
When the default route is set to 0.0.0.0 0.0.0.0 10.10.10.254 (4560 switch) domain browsing works perfectly
When the default route is set to 0.0.0.0 0.0.0.0 10.10.20.2 (3560G) switch I can ping any ip address in that range and the address on the other
interface ip adresses on the 2600 (eg. 10.10.30.1 / eth2, 10.10.40.1/ eth3 etc.)
I have tried to weight the routes after adding them both to the configuration, but that doesn't seem to work at all.
The switch connects back to the office via vlan1 (10.10.10.253)
The 2600 is connected to port 1, which belongs to Vlan2 (10.10.20.1)
And client computers sit on ports 2-12 belonging to Vlan10 (10.0.0.240)
So in a nut shell, how would I go about setting it up so the machines on 10.0.0.0 can connect to 10.10.20.0 and 10.10.10.0 and vice versa at the same time? Everything was working fine until I rebooted the switch (3560g), which makes me think the person that configured this before me didn't save the running config to the start up config.
View 4 Replies
View Related
Dec 2, 2011
How i can transfer the router logs to email address.Wev are using the router 2600.
View 5 Replies
View Related
Jan 10, 2012
My network generally runs older routers (2600 series) with 16 port switch modules (NM-ESW-16). This has always worked great since I can configure the router and the switch ports on the fly, making changes to either as necessary. Well I am upgrading to 2811 routers, and we wanted to get gigabit ethernet ports on our switch modules. I think I made an error when I purchased a few of these switch modules: NME-16ES-1G.
The first problem, is that the switch ports don't even show up on the router config, I have to establish a session into the switch, (And I can't seem to get back to the router unless I manually switch off power and restart). I don't like this type of switch module, it's like I'm running a completely separate device, and while having a layer 3 switch is cool, It doesn't let me setup routing protocols so I don't like doing it this way. I want to go back to using a switch module that simply adds a ton of ports to my router like the NM-ESW-16. (Note: The NM-ESW-16 does actually work in the 2811 and would be perfect if it were Gigabit speed.)
The seconds problem is that the NME-16ES-1G isn't actually a Gigabit switch. It has a single gigabit port, but the 16 ports are all Fastethernet, and not gigabitethernet. So ideally, I am looking for a switch module that I can fully configure from the router interface that has 16 gigabitethernet ports, and works with a 2811. IE I want to do this. [code]
View 4 Replies
View Related
May 21, 2012
We have two MPLS circuits managed by two different suppliers, one carries VOICE the other DATAWe are to decommision the VOICE MPLS and have increased the bandwith of the DATA MPLS to carry VoIP traffic too.
At both of our sites A & B ,devices connected to the LAN have a default gateway of the VOICE providers Cisco 2600 router , which then goes into the LAN switching. (see diagram)So what I am trying to achieve is toto simply replace these 2600 routers from the VOICE MPLS provider with our own so we dont have to change the default gateways at both sites.
Testing
Our Cisco 2600 routes are plugged into each LAN switching environment with two subinterfaces configured, one for voip and the other for dataThe problem is from the router and respective subinterfaces we can get to the other sites destination without any issue, but if for example a user is at site A with Ip address 10.16.11.12/16 they cant ping the VOIP subnet at site B 10.3.11.0/24. But If a ping is issue from the Site A test router then the 10.3.11.0/24 subnet is reachable but only on the 10.3.12.0/24 configured subinterface.So i guess what Im saying is 10.16.0.0/16 from the LAN needs to be able to get to 10.3.11.0/24Note at site A 10.16.0.0/16 & 10.3.12.0/24 can communicate no problem and at site B 10.207.0.0/16 & 10.3.11.0/24 can communicate no problem.We are using IP routing, should we be using route-maps?
View 15 Replies
View Related
Nov 17, 2011
I need to configure an existing 2600 router to use dynamic NAT for access to the web and ALSO I have (5) fixed IP addresses for use with an email server, a web server, and (3) future servers. I do not know the concept of how to set this up. I'm currently using dynamic NAT for the web and this seems OK but I dont know how to map my fixed servers. I assume this is done with static NAT. Do I need to add sub interfaces on the S0/0 T1 interface for each of these fixed IPs? Then do I somehow do static NAT on these fixed IPs to their respective servers?
View 14 Replies
View Related
Jan 15, 2013
client originally connects to the 4500E, moves to the 2960s and then cannot connect back to the 4500E.My design is a 4500E (configured for routing) and a 2960s. The 2960s is trunked to the 4500E, no vlan pruning.
Tried;
- shut/no shut port on the 4500E doesn't work
- no result for sh ip arp | i (clients mac) or sh mac address | i (clients mac) on the 4500E
The only way I can get the user back online is removing the 2960s, not a desirable solution as other clients are on the 2960s.
View 2 Replies
View Related
Mar 17, 2013
i have a simple router on a stick config which is providing dhcp to a customer SSID. however i don't want employees to stay on it and eat the band width since its open. the lease is set to an hour, is there anyway that i could set it so that once your lease expired it can't be renewed for 4 about 8 hours? I am using a cisco 2600 router in this setup.
View 1 Replies
View Related
May 8, 2013
My question relates to how many clients can be connected to a 2600 series AP. The documentation states 200 clients per radio and the AP has three radios. However when my AP gets to 200 it rejects further clients with the following log: [code] I see this exact message many times and each time the radio mac address is the same and the number of clients connected is 199. The same mac address is used for both 2.4ghz and 5ghz so does this AP have a single logical radio covering both 2.4 and 5ghz frequency ranges and is the limit for all connected clients 200?When viewing the AP details under the Wireless tab it only lists one mac address for each AP for both 2.4ghz and 5ghz frequencies.
View 11 Replies
View Related
May 2, 2012
I have a Cisco 2600 series with 2 X Fast Ethernet ports and I would like to configure the cisco to perform the task if it is possible.The scenario is:
2 networks:
F0/0: 192.168.x.x
F0/1: 10.1.x.x
No communication between them except one way multicast from F0/1 to F0/0.
View 1 Replies
View Related
May 24, 2011
How come the 2600 series IOS has the show mac-address command but it does not display anything? you need to use show arp? is this for when you use one of those network modules that is a switch?
View 2 Replies
View Related
Aug 30, 2012
I bought some hardware and created my own lab to prepare for the CCNA. I only have one machine with a serial port and whenever I try to connect to a router (I've tried multiple purchased from different sources) nothing happens on the screen. If I wait for a couple of seconds and hit enter I get the response shown on the screen in the screenshot I have inserted. If this image is too small I have also attached. looks like it has already asked me this but I am unable to see it. Shouldn't I see some information when I attempt to connect, some acknowledgement that I have connected? I have tried using both hyperterminal anbd PuTTy.
View 1 Replies
View Related
Jan 27, 2013
I purchased the AP wrongly, instead of getting the "Standalone/Autonomous" (AIR-SAP2602E) version but I purchased the controller-based version (AIR-CAP2602E); my question is can I use "ap3g2-k9w7-tar.152-2.JB.tar" too flash it to a "Standalone/Autonomous" version?
View 21 Replies
View Related
Nov 10, 2011
- I have an older router 2600 running 12.1(4) IOS.
- There are a few clients connected to it via the frame relay connection.
- There is an IP that clients access 192.168.1.10 for example
- We need to do a NAT for this IP for one specific client only like "ip nat inside source static 192.168.1.10 1.1.1.1"
- However if I do that, that will effect other clients too
- On the interface for this client I'll be using "ip nat outside"
- Is there a way to accomplish this without effecting other customers?
View 6 Replies
View Related
Dec 2, 2011
I've been working with these two Cisco devices in my home off and on for several months now but I just can't take it anymore, I'm about to throw them away and go back to Linksys router.
I have a Cisco 2600 Router with only one Ethernet card in it so I have to trunk from my 3550 Switch to that device. I'd like to have my ISP and all users plug into switch and all trunk back to the router's sub interfaces. Currently, I have started over...again, and am unable to simply get the router and switch to ping each other if I put sub-interfaces on the router. See my configs:
2600 ROUTER:
Router#sho run
Building configuration...
Current configuration : 555 bytes
[code]......
3550 SWITCH:
Switch#sho run
Building configuration...
Current configuration : 2302 bytes
!
version 12.2
[code]..........
Port F0/24 is in VLAN 1, as are all ports but Port F0/1 which is my desktop PC. I mocked it up in Packet Tracer and it works just fine. This is just a simple setup and I'm making sure I can ping between switch and router before I move to each next step.
View 40 Replies
View Related
May 7, 2013
We are having a hard time to console into to the APs using the serial connection (USB to serial converter).We have tried the recommended settings (9600, 8 bits, no parity, 1 stop bit, no flow control (also tried XON/XOFF)) without any success.We are able to connect to 3560 series switches and 5508 WLCs using the same cables, notebook and application (putty, hyperterminal & secureCRT).
View 4 Replies
View Related
Mar 4, 2013
If the 2600 series access points are compatible with a 4404 controller running 7.0.235.3 code? I was looking for a compatibilty matrix for the AP to controller to code comparison but couldn't find one.
View 1 Replies
View Related
Jun 13, 2012
about to install first UC320w and wanted some sample 800 series router configurations showing required port fowarding, ACL entries and QoS examples.
View 5 Replies
View Related
Aug 23, 2012
I have a Cisco 800 series router that I need to set NAT up on. There will be four computers connecting to the internet through it. I already have the IP address coming from my cable modem I just do not know the command to get it to translate to my internal dhcp pool I have setup.
View 1 Replies
View Related
Sep 17, 2012
I am trying to configure SDM 2.5 on a cisco 2600.I have access via telnet to the router and was able to change the enable password - which i think is level 15 (right?) and setup (and bring up) the ip on the ethernet interface. I can ping - and get response from - the router Trying to install SDM on the router i need to provide the default username i tried both admin/administrator but SDM can't communicate with the router?
View 21 Replies
View Related
May 22, 2013
I have Router 2800 series Global nating is configured on it.
ip nat inside source list 111 interface Dialer1 overload
!
access-list 111 deny ip 192.168.1.0 0.0.0.255 192.168.0.0 0.0.0.255
access-list 111 permit ip 192.168.1.0 0.0.0.255 any
My object is that i want give internet access only for few users ip E.g IPs addresses from range 192.168.1.0-10 can acess intenet access other all are deny.How i do this with ACL .
View 2 Replies
View Related
Dec 27, 2012
I would like to setup RDP on my cisco router so I can access my server from outside my network. I also have a router from my ISP that has DHCP for my external IP address and DHCP for my internal as well.
View 3 Replies
View Related
Aug 23, 2012
I have a Cisco 800 series router that I need to set NAT up on. There will be four computers connecting to the internet through it. I already have the IP address coming from my cable modem I just do not know the command to get it to translate to my internal dhcp pool I have setup. I have also been doing some research, seeing as I only have one public IP address coming from my ISP will I have to use PAT as well?
View 1 Replies
View Related
May 1, 2013
I have a Cisco 881 router running 15.1(4)M4. I am trying to configure SPAN on it to mirror my outside interface (source) to one of my LAN interfaces (dest).
!--- WAN interface
interface FastEthernet4
description Comcast WAN$ETH-WAN$
[Code]......
As you can see from the above output there is a problem with the command on this interface. When I try to set Fa0 as my source it works fine:
rtr(config)#mon session 1 source int fastEthernet 0
rtr(config)#
Is this because fa4 is layer 3 and fa0 is a switchport? If so, is there another way to set fa4 as the source?
View 4 Replies
View Related
