I have a Cisco 2600 series with 2 X Fast Ethernet ports and I would like to configure the cisco to perform the task if it is possible.The scenario is:
2 networks:
F0/0: 192.168.x.x
F0/1: 10.1.x.x
No communication between them except one way multicast from F0/1 to F0/0.
how is the IP configuration for this Fast Ethernet F0.
This is because usually we only assign IP to the BVI interface. Is it after that, the Fast Ethernet F0 automatically also be assigned the same IP?
As such, when goto the Fast Ethernet F0 by CLI, by using no shut then this will Enable the Fast Ethernet Port?
I have 4 cisco 2960 switches to which many users are connected. No vlans are the only default vlan 1 is there. Now I want to make ether channel on switch 1 whcih has 24 fast etherenet ports. Can I make port 1- 8 as one ether channel which are connected to users or i can only make ethere channel of ports that are connectd to other switchs. If I can, how the other switchs will comnicate with the switch ports bundalled in the ether channel in switch 1.
View 6 Replies View Relatedwhat is difference between Ethernet and fast ethernet
View 1 Replies View RelatedMy question relates to how many clients can be connected to a 2600 series AP. The documentation states 200 clients per radio and the AP has three radios. However when my AP gets to 200 it rejects further clients with the following log: [code] I see this exact message many times and each time the radio mac address is the same and the number of clients connected is 199. The same mac address is used for both 2.4ghz and 5ghz so does this AP have a single logical radio covering both 2.4 and 5ghz frequency ranges and is the limit for all connected clients 200?When viewing the AP details under the Wireless tab it only lists one mac address for each AP for both 2.4ghz and 5ghz frequencies.
View 11 Replies View RelatedI am asked to implement the security in campus Network. i.e. In this network we want to block some websites, We don't want to use any 3rd party software or proxy server and content filtering module to block theset.my router IOS is advance securityk9 How to block the website in a Cisco 2600 series router by using the command. What is the access list we need to use to block.Assume we want to restrict,
[URL]
Here we are using Cisco 2600 series router and 2900 series switch. In router we are using the2Mb lease line link
How come the 2600 series IOS has the show mac-address command but it does not display anything? you need to use show arp? is this for when you use one of those network modules that is a switch?
View 2 Replies View RelatedHow to configure HSRP in techroutes 2600 series router and aaa authentication
View 2 Replies View RelatedI bought some hardware and created my own lab to prepare for the CCNA. I only have one machine with a serial port and whenever I try to connect to a router (I've tried multiple purchased from different sources) nothing happens on the screen. If I wait for a couple of seconds and hit enter I get the response shown on the screen in the screenshot I have inserted. If this image is too small I have also attached. looks like it has already asked me this but I am unable to see it. Shouldn't I see some information when I attempt to connect, some acknowledgement that I have connected? I have tried using both hyperterminal anbd PuTTy.
View 1 Replies View RelatedI have a 2600 Router series and I cannot remember the Password. I have tried following web pages that state to use control Break on the boot up but its not working.can reset that pw and write erase my configuration file?Here is my boot up. I have tried hitting control break at the very beginning over and over and then again when at the cold boot it has not worked....
System Bootstrap, Version 12.2(7r) [cmong 7r], RELEASE SOFTWARE (fc1)Copyright (c) 2002 by cisco Systems, Inc.C2600 platform with 131072 Kbytes of main memory
program load complete, entry point: 0x80008000, size: 0x1c9468cSelf decompressing the image : ######################################################################################################################################################################################################################################################################################################################################################################################################################################################################## [OK]
Smart Init is enabledsmart init is sizing iomem ID MEMORY_REQ TYPE00036A 0X000B3B80 C2610XM Single Fast Ethernet 0X00098670
[code]....
I purchased the AP wrongly, instead of getting the "Standalone/Autonomous" (AIR-SAP2602E) version but I purchased the controller-based version (AIR-CAP2602E); my question is can I use "ap3g2-k9w7-tar.152-2.JB.tar" too flash it to a "Standalone/Autonomous" version?
View 21 Replies View RelatedI have been having trouble forwarding ports for different softwares and servers. I just upgraded my internet and my ISP sent me a new modem/router all in one. I am using a wired setup to my desktop. The router I am using is Sagem FAST 1704.
My ISP told me that they only give support for game consoles, the dumbest thing I ever heard since I don't pay for their internet so I can play games. Cannot forward a simple port. Port 100 in specific.
When I forward ports, I am certain that I'm typing in the right Ip address digit because I checked ipconfig. Then I check the 'canyouseeme' website and it tells me that the port is not open on my ip address. I have tried other means of checking to see if the port is open but they all tell me the port is closed. Once in awhile the port will be open but most of the time it isn't.
I plug in my older modems and it doesn't make a difference when I re-set up the port forwarding to the new IP so I guess it isn't a problem with the modem or router. I changed all my ethernet and phone cords and filters as well. My isp told me that they do not block ports.
My isp is Windstream. I cannot set up a static IP in network connections because when I do the internet doesn't work at all even if I set the exact same settings that are currently set. This happens with both modems I have. I do not use two devices at one time just the modem or the modem/router, there are no other computers connected and filters are on all phones/satellites. I am using Windows XP, not sure what other info you will need.
My isp keeps telling me they do not support setting up vpn's. I do not need support for that I just want to open a port. lol the next thing they told me is, you guessed it, "We do not support setting up VPN please contact your work IT........" which doesn't exist. I spoke to three of them and they all said the same thing, except one told me they were going to open ALL ports for me. That didn't happen.
Was just wondering if we can segregate users using subnets and not vlans in cisco switches? We have few groups we want to segregate onto different subnets, but don't want to use Vlans. Apparently I have been told that vlans do way too much packet processing and slows the network.
we are working on a school network. Want to segregate staff/students/admin.Further segregate students by year levels. This means if we were to use vlans we would have around 15 vlans. will it slow the network? (thats what I have been told and i dont agree to it). How to implement this topology without vlans and by just using subnets.PS: we use Juniper EX4200 (layer3), Juniper EX2200 x15,H3C 3100 x16 and cisco 2600 x1 switches on campus.
does Cisco 2600 series switch support 802.1x and DHCP snooping?
View 6 Replies View RelatedWe are having a hard time to console into to the APs using the serial connection (USB to serial converter).We have tried the recommended settings (9600, 8 bits, no parity, 1 stop bit, no flow control (also tried XON/XOFF)) without any success.We are able to connect to 3560 series switches and 5508 WLCs using the same cables, notebook and application (putty, hyperterminal & secureCRT).
View 4 Replies View RelatedWe are upgrading our incoming Internet service from 30 Mb 10/100 to 100Mb 10/1,000.Will my 2600 series router support the 10Mb 10/1,000 traffic from my new modem?Do I need to change my interface speed from 100 to 1,000? I to be sure my router will support the upgrade. [code]
View 8 Replies View RelatedIf the 2600 series access points are compatible with a 4404 controller running 7.0.235.3 code? I was looking for a compatibilty matrix for the AP to controller to code comparison but couldn't find one.
View 1 Replies View RelatedI need to add another fast Ethernet port to an old 2621 router, I need a NM-1FE-TX OR NM-1FE-FX-V2 ??
View 4 Replies View RelatedI currently have 2 PCs that are directly connected to each other via a 1Gbs Cat6 connection.I don't currently have a 1Gbs router so what I am doing right now is unhooking this connection and reconnecting both machines to my router when I need internet access. I have ordered some USB Wi-Fi adapters so I can have both machines access the internet that way whilst still use FTP between them on the 1Gbs line.If I were to scrap that idea and get a 1Gbs hub, connect both PCs straight into that, and then also connect the hub to my 100mbits router, would the 2 computers be able to communicate with each other at 1Gbs and then talk to the router at 100mbits, or would the whole network run at 100mbits.I don't really want to have to shell out on a 1Gbs router as I don't need anything else on the network to run at that speed.
View 6 Replies View RelatedWe have an ASA 5505. 5505 comes with two default vlans 1&2 with each of them marked as inside & outside respectively.My query is , if i do not want to use vlans on 5505 and only want to use the Ethernet ports as pure physical layer 3 ports, is it possible?i.e. i want to assign a layer 3 ip address on eth0/0 and eth0/1 and make them as the inside & outside interfaces rather than vlans. is it possible to do away with vlans in 5505 & will it work otherwise?
View 3 Replies View RelatedI am having a heck of a time finding information on this. I have a 2620xm router that only has one Ethernet port on it. Is there an expansion I can get that allows me another Ethernet port. I have thus far assumed that all of the WIC cards won't allow me to attach to an Ethernet LAN.
View 7 Replies View RelatedI have a cisco 1841 whose LAN interface is showing status as "Fastethernet 0/1 is up , line protocol is down" the duplex and speed settings in the Router are in Auto mode and the Router was working fine till now , when i changed the duplex settings to duplex full , speed 100 the ping replies comes back with 5-6 replies then the link dies again..
View 1 Replies View RelatedI have a home lab. I am trying to connect a 1710 to a 2610 with just using the fast ethernet ports. I understand that serial connections and t1 csu/dsu connections use clocking, etc. How can I configure FA ports to do the same AND be routable?
View 6 Replies View RelatedI had a question regarding the Cisco 2811. I tried fitting an NM 2FE-2W card and the fast Ethernet interfaces of the module never get recognized. Is there a special command to enable it or isn't the module supported at all by the router. If not , is there a way to have the router possess more than the 2 Fast Ethernet interfaces it already has? Let me know if any more info is needed from my end.
Another question I have out of curiosity. Is it possible to make the controller T1 port of a VWIC 1MFT-T1 or a VWIC 2MFT-T1 act as a fast Ethernet.
Is there a keyword that we use under the interface to specify that it is purely management?
We need to assure that the subnet and any node on that subnet is not shared with the default routing table.
how do we set the gateway for the management interface if the node we are sourcing the ssh session from is on a different private subnet?
I’m working with a managed switch that has three V LANs setup on it. Recently the domain changed and the wireless V LAN can no longer access the internal website. I found access rules, in the switch that allowed the wireless V LAN to use the DNS server on the private/staff V LAN. Their DHCP scope is on the switch and DNS is set there. The Website is also on the V LAN with the DNS server. This configuration totally cuts out external DNS usage. It stopped working though. It is as if when things switched on the Domain the wireless users were denied DNS requests. The switch was not touched at that time. I’m looking at it though and it seems that I may have conflicting rules.
The version is 12.2. I believe its a Catalyst 2600~
DHCP scopes: ip dhcp pool INSIDE network 192.168.1.0 255.255.255.0 default-router 192.168.1.1 dns-server 192.168.1.6 192.168.1.4 domain-name saline.lib.mi.us
ip dhcp pool WIRELESS
network 172.16.0.0 255.255.255.0 default-router 172.16.0.1 dns-server 192.168.1.6 192.168.1.4
Here is the V LAN Setup:
Interface Vlan1
ip address 192.168.1.1 255.255.255.0
[code]...
Here are two access lists that should be allowing the traffic from 172.16.0.0 into the list IPs/Ports. These do no work.
ip access-list extended WIRELESS-PRINT
permit tcp 172.16.0.0 0.0.0.255 host 192.168.1.12 eq 30044
permit tcp 172.16.0.0 0.0.0.255 host 192.168.1.12 eq 21326
permit tcp 172.16.0.0 0.0.0.255 host 192.168.1.12 eq 6987
[code]...
During my testing I removed the Deny rule and everything worked. deny ip 172.16.0.0 0.0.0.255 192.168.1.0 0.0.0.255
However, the “ permit ip any any “ rule, makes all the port rules pointless because when this rule is in place solo, I can ping and access everything on the 192.168.1.0 network. Is there a way to deny everything, except what I permit? Because when I remove the ip any any, then they cant even get out. Perhaps there a better way to say, the wireless users can get out but only get into the sub net over specific ports? I have a feeling it may have not be thought out entirely when initially created. However, the big mystery is that it worked before secondary domain controller failed.
I'm using a Cisco 1812 to route traffic from a small location with 10 users.. Users are complaning about packet loss, and programs with live database connection is freezing..On the router i've checked one of the Fastethernet interfaces, and I can see that the input errors are increasing constantly. [code]
View 5 Replies View RelatedI am having some issues with a 861W router connected to a cable modem. Traffic is passing fine but my SNMP monitoring tool is showing continual changes to the ifLastChage mib. [code]
View 8 Replies View RelatedI have cisco 1801W . Earlier I am using ADSL dynamic IP address on RJ 11 through the ADSL Port but now the ISP change the connection to RJ45.
I am trying to configure it but unable to do this. ADSL line is okay because When I am connecting through the ISP router it is working fine. I have connected the ADSL RJ45 cable in the router fast ethernet 0.But I wanted to use Cisco 1801 Router so that I can use the ADSL as primary and ISDN as the backup.
Below is my configuration, eiteher this is possible to configure ADSL through RJ45 in 1801 and what configuration require for this.
Router#show ip int brief
Interface IP-Address OK? Method Status Protocol
FastEthernet0 unassigned YES DHCP up up
BRI0 unassigned YES unset administratively down down
BRI0:1 unassigned YES unset administratively down down
BRI0:2 unassigned YES unset administratively down down
[code].....
It is a single router with dual ISPs. It is a 2800 and there is failover configured. I have implemented object tracking and the feature works great except that lately, whenever there is a lot of traffic coming perhaps from the internal users, we start getting intermittent outages.
I have gone deep into looking into this problem and have determined that our ISP#1 does not have any problems. What I think is happening is that whenever the router receives a lot of packets (30-40 users on the internal network) destined to the outside, the router CPU maybe gets too busy and the router then believes that the objects are no longer reachable and it triggers a failover which causes the router to re-direct traffic to the ISP#2. Then, because these are just quick burst of traffic, in the next 30 to 45 seconds after the router re-directed the traffic to ISP#2, the router object tracking engine detects that the objects are now again reachable and this then causes the router to re-direct all traffic back to ISP#1.
This cycle then continues all day on how to prevent this.
Is there a way to perhaps tell the router to completely shut down the interface facing ISP#1 whenever there is a hicup and to keep it shutdown for at least 8 hours? This way I can prevent the router from going crazy.
Or is there a way to perhaps prevent this at the internal (LAN) interface? Are there some metrics like QoS that I can implement on the internal Fast Ethernet Interface to prevent the burst of traffic from eating up the CPU?
I am troubleshooting interface resets on a 3660 connected to a 3550 over Fast Ethernet. I have hard coded both sides for full duplex and 100Mbit. The 3660 is incrementing interface resetes about 4-6 times a day and the 3550 is clean. I have noticed this in other similar configurations as well.
View 4 Replies View RelatedI have a couple of 2600 APs (external antenna) which are getting PoE from my switch but no ethernet. This is happening on both APs. If I connect a laptop to the (cat5e) cable I get ethernet. If i move the AP to another patch lead adjacent to my switch I get ethernet connectivity too. So, change the cable is the answer I thought, however I have exactly the same issue on both APs and each ethernet cable has been reterminated a number of times (straight through). I wonder is the 2600 AP less tolerant to the actual ethernet cable ?
I just swap the cable, however the patch leads have been run (only 15m or so) and have been replaced once - relaying again is not an easy job. It's more a case of reterminating the cable that is already there and as I've already done this a few times on each patch lead and the results are the same each time I'm thinking I'm missing something obvious.
how many users supports the 2600 series ap air voice, video, and data average any document or link
View 3 Replies View Related