We are having a hard time to console into to the APs using the serial connection (USB to serial converter).We have tried the recommended settings (9600, 8 bits, no parity, 1 stop bit, no flow control (also tried XON/XOFF)) without any success.We are able to connect to 3560 series switches and 5508 WLCs using the same cables, notebook and application (putty, hyperterminal & secureCRT).
View 4 Replies
If the 2600 series access points are compatible with a 4404 controller running 7.0.235.3 code? I was looking for a compatibilty matrix for the AP to controller to code comparison but couldn't find one.
View 1 Replies View RelatedI bought some hardware and created my own lab to prepare for the CCNA. I only have one machine with a serial port and whenever I try to connect to a router (I've tried multiple purchased from different sources) nothing happens on the screen. If I wait for a couple of seconds and hit enter I get the response shown on the screen in the screenshot I have inserted. If this image is too small I have also attached. looks like it has already asked me this but I am unable to see it. Shouldn't I see some information when I attempt to connect, some acknowledgement that I have connected? I have tried using both hyperterminal anbd PuTTy.
View 1 Replies View RelatedI know that the deployment guide for 2600/3600 access points states that if you have surveyed for a 3600 deployment, you don't need to survey again for a 2600 deployment. As the the 3600 is the higher specification model, is it safe to assume the reverse? I.e. a site survey carried out using 2600 access points is valid for a 3600 deployment, or is this too simplistic?
View 5 Replies View RelatedI am recently engaged by a client to convert his network to wireless network. My client operates in an office with 8 floors and also concrete walls. On making my research i came about your product Cisco AP500 Series Wireless Access Points.I will like to know if this product can work for my client perfectly or I will need to get other enhancement to make it work at its optimum.
View 2 Replies View RelatedI have a customer who bought Cisco Aironet 3500 Series. Currently 4404 WISM Controllers are installed with 1142 Access-Points. The WLC-Version is 6.0.199.
Will the 3500 Series Access-Points work? (Of course without the spectrum intelligence feature)?
The Q&A says the following: Are there any concerns with supporting the new Cisco Aironet 3500 Series Access Points with the older Cisco 2000, 2100, 4100, or 4400 Series Wireless LAN Controllers?
I have some Cisco Aironet 1100-series, 1040 series, 1240 series, 1130 series and 1200series and i would like to upgrade them to the newest ios software.
The IOS that are present in my access points are 12.3(8)AJ and 12.3(11)JX.
We are re-designing our wireless network and are navigating the security options.Are design will include a 5508 WLC and 3600 series APs. We plan on breaking our wireless out into four VLANS.Is 802.1x the standard for wireless authentication?What EAP flavor would you recommend for wireless? We will be supporting an environment with a variety of mobile devices (iPhone, iPad, HP tablets, Dell laptops, etc.). We will also be supporting wireless Cisco VoIP phones. Someone suggested choosing between EAP-Fast or EAP-PEAP, does this seem reasonable? Also, if we want to authenticate users using their AD account, we need to have NPS running on the AD server and use the radius protocol from client to server, is that right?
View 1 Replies View RelatedMy Linksys Routers IP is 192.168.1.1 am unable to access the console, although i changed the computers IP 192.168.x.y. i have tried by Hard Resetting the Router but still the same?
View 1 Replies View RelatedI have linksys ADSL Router which is having one line port for Phone Line and 4 Ethernet Ports.The Router IP is 192.168.1.1. When i connect this Router through one of its Ethernet Port to one of the Network Point(which is DHCP enabled)is working fine. I get the IP 192.168.3.x from my existing DHCP not from the ADSL Router which is enabled.Secondly, Although i can Ping the Router IP 192.168.1.1 from Wifi client 192.168.3.X, But when i try to open the Router Console a Login window open and is says " your are trying to access the Router in an insecure ways and it doesnt not authenticate ID and PWD.When i directly connect Router to my Laptop then am able to do so.
View 1 Replies View RelatedMy question relates to how many clients can be connected to a 2600 series AP. The documentation states 200 clients per radio and the AP has three radios. However when my AP gets to 200 it rejects further clients with the following log: [code] I see this exact message many times and each time the radio mac address is the same and the number of clients connected is 199. The same mac address is used for both 2.4ghz and 5ghz so does this AP have a single logical radio covering both 2.4 and 5ghz frequency ranges and is the limit for all connected clients 200?When viewing the AP details under the Wireless tab it only lists one mac address for each AP for both 2.4ghz and 5ghz frequencies.
View 11 Replies View RelatedI recently installed Connectifyme (Connectify for Windows - Turn your Laptop or Smartphone into a Secure Wi-Fi Hotspot) so that I could broadcast a wifi signal for my phone. Testing at home, I used it to repeat my router and connect through my computer. But when I took the laptop to the place at which I primarily need the utility (I have access to ethernet but no wifi), and used it to broadcast an unprotected ad-hoc ethernet->wireless network. Since using it in this way, my laptop has been unable to locate my home router, or my college's public wifi, though it is able to locate networks which either I am unable to connect to, or do not supply wifi internet. I tried making a ticke on connectifyme's support page, but after something like a week I've yet to get a reply. Uninstalling connectify did nothing, nor have I been able to find any issues with the network card or windows not recognizing the card. I'll be using windows 7 default utility to see how that works, but I first need to be able to reconnect to networks I know are in range.
how I can correct the issue with my wireless card not finding networks?
I purchased the AP wrongly, instead of getting the "Standalone/Autonomous" (AIR-SAP2602E) version but I purchased the controller-based version (AIR-CAP2602E); my question is can I use "ap3g2-k9w7-tar.152-2.JB.tar" too flash it to a "Standalone/Autonomous" version?
View 21 Replies View RelatedAlthough I hasten to point out that I have owned and used an 'IBM' type PC since 1988 and have always managed to get things configured correctly until NOW!
Apart from the last time I tried to use a Linksys product. I had the WRVS4400N recommended to us by a friend as we run a small FTP server to share promotional materials amongst sales operatives around the world, wanted to protect it from intrusion and was told that a Cisco Linksys product with a VPN was the way to go.
I duly purchased a WRVS440N and have been trying to log into the admin console via both browsers (IE9 and Google Chrome) that are installed on a laptop running Win7 which in turn is the only thing connected to the stated device via ethernet port 1... I have tried accessing it via http://192.168.1.1 and have even tried a suggestion from another forum to try https://192.168.1.1 - this only results in my being told that the address does not have a trusted certificate and I even tried every suggested workaround...
I have tried all kinds of reset periods from 10 seconds to a minute, both hot and cold and each time the result is the same - I type in 'admin' and 'admin' in the appropriate boxes and the dialogue box continues to return to the browser window with empty fields...
The shame is that I have managed to re-flash a BT Voyager 190 ethernet modem successfully with DynaLink v3.29a firmware (which allows it to be used with any ISP besides AOL [for whom this modem was solely intended]) and can set it up as a DHCP server, non-DHCP with a single link to another server or non-DHCP and no link.... The point is the modem works... I'm using it right now to type this! We have a single static IP from our ISP and the BT modem is working just fine (as is the TP-Link wireless modem/router that the WRVS4400N was intended to replace)... there are other options in it's firmware for port forwarding, etc and I'm convinced that it wil be adequate for use in conjunction with the WRVS4400N.
I have to concede that the WRVS4400N was not sold to us as NIB; it was sold as re-conditioned and was shipped to or via Ingram Micro Distribution from Cisco Systems, Veldweg 3, Herkenbosch 6075 NL (Holland) via UPS on or about the 31st of July, 2012... there is a shipping label on the original packaging that tells me that so it has in fact been back to Cisco at some point and for some reason.
I am having FWSM in active /standby mode deployed on two different cat 6k chassis. Unable to access the fwsm module from switch using ' session module mod_no processor 1 ", it throws error " % telnet connections not permitted from this terminal" Running Version 3.2.6 on fwsm, Cat 6k is running 12.2.33.SXH1,
switch#session slot 3 processor 1
The default escape character is Ctrl-^, then x.
You can also type 'exit' at the remote prompt to end the session
% telnet connections not permitted from this terminal
---------------------------------------------------------------------------
have allowed telnet on line vty, configuration on Line vty is simple allowing all transport protocols
line vty 0 4
exec-timeout 5 0
transport input all
transport output all
line vty 5 15
exec-timeout 5 0
transport input all
transport output all
I have 2960 switch and i can't access it using my console cable .I can access other switches in my network ( 3560 & 2960 ) but i can't access only this switch.may be the console port in the switch damaged? or it's a bug ?? !!! although the switch is worked normally.
View 11 Replies View RelatedI not able to access cisco 2811 router (AC operated) through console port when I try to access it by selecting COM Port, but I able to access by selecting the TCP/IP option.
View 5 Replies View Relatedhow many users supports the 2600 series ap air voice, video, and data average any document or link
View 3 Replies View RelatedI am asked to implement the security in campus Network. i.e. In this network we want to block some websites, We don't want to use any 3rd party software or proxy server and content filtering module to block theset.my router IOS is advance securityk9 How to block the website in a Cisco 2600 series router by using the command. What is the access list we need to use to block.Assume we want to restrict,
[URL]
Here we are using Cisco 2600 series router and 2900 series switch. In router we are using the2Mb lease line link
I have a Cisco 2600 series with 2 X Fast Ethernet ports and I would like to configure the cisco to perform the task if it is possible.The scenario is:
2 networks:
F0/0: 192.168.x.x
F0/1: 10.1.x.x
No communication between them except one way multicast from F0/1 to F0/0.
I have powered ON WLC(2100 Series) and connected LAN port from WLC to my PC. To access WLC GUI what is the factory default IP address?
I connected Console Port of WLC to Serial port of my PC. I have configured WLC as per the WLC quick guide.
Management Interface IP address :: 10.40.0.4
Management interface Net Mask: 255.255.255.0
[Code].....
The result is same even when below commands are used Configuration modeport adminmode all enablenetwork webmode enablenetwork secureweb enable
How come the 2600 series IOS has the show mac-address command but it does not display anything? you need to use show arp? is this for when you use one of those network modules that is a switch?
View 2 Replies View RelatedHow to configure HSRP in techroutes 2600 series router and aaa authentication
View 2 Replies View RelatedI have a 2600 Router series and I cannot remember the Password. I have tried following web pages that state to use control Break on the boot up but its not working.can reset that pw and write erase my configuration file?Here is my boot up. I have tried hitting control break at the very beginning over and over and then again when at the cold boot it has not worked....
System Bootstrap, Version 12.2(7r) [cmong 7r], RELEASE SOFTWARE (fc1)Copyright (c) 2002 by cisco Systems, Inc.C2600 platform with 131072 Kbytes of main memory
program load complete, entry point: 0x80008000, size: 0x1c9468cSelf decompressing the image : ######################################################################################################################################################################################################################################################################################################################################################################################################################################################################## [OK]
Smart Init is enabledsmart init is sizing iomem ID MEMORY_REQ TYPE00036A 0X000B3B80 C2610XM Single Fast Ethernet 0X00098670
[code]....
I am working on a site that has recently added a new subnet and I am unable to ping any of the stations on this new network. I have configured an Exempt NAT rule just the same as the rules allowing access to other networks. I have a feeling the problem is in the Site-to-Site VPN configuration since the new subnet is at the primary location over the VPN.
In the site-to-site configuration I added the new subnet to the list of "Remote Networks" and I still can't communicate with any of the devices on the network. If I go to the main site I have no problems so it appears to be related to the VPN or a configuration in the ASA on that site.
A port scan shows that all the traffic is "filtered" so somewhere either the site ASA or the main ASA is blocking the traffic.
does Cisco 2600 series switch support 802.1x and DHCP snooping?
View 6 Replies View RelatedWe are upgrading our incoming Internet service from 30 Mb 10/100 to 100Mb 10/1,000.Will my 2600 series router support the 10Mb 10/1,000 traffic from my new modem?Do I need to change my interface speed from 100 to 1,000? I to be sure my router will support the upgrade. [code]
View 8 Replies View RelatedI'm using Linksys WAG200G Wireless modem and connection mode is "Bridge Mode Only", in this mode I'm not getting the 192.168.1.1 setup console and Wifi facility.
View 3 Replies View RelatedWe have a Cisco ASA5505 here that provides DHCP and routing to all our devices in our network. We also have a few other switches and wireless access points connected directly to the back of the ASA5505.For the past year all the wireless network signals has been working fine however starting last month, none of the wireless access points (we have three WRT54G) would allow proper connection (dropping connection, slow internet).I thought this maybe all THREE wireless access points are toast/bricked. So i went out and bought brand new Netgear WN604 and even with the new WAP i'm having same connectivity issues (really slow internet).When hardwired directly to the switches we get BLAZING fast internet & connectivity, no issues.
I called CISCO TAC and they automatically said "our ASA5505 is fine, it has to be your wireless access points" not working properly. I explained to them that i also purchased two brand new access points and they are doing the samething now, how can that be?
I've had some long standing issues that I've tried various things to fix. I have two WAP4410N access points set up at a smaller sister company. Wireless clients (laptops) are not receiving DHCP assigned IP addresses. If I type in an IP manually, it works fine.The sister company has a point to point T-1 connection to our main building. Our main building has the DHCP server. The router on the sister company end is configured as the DHCP relay.
I've upgraded the firmware three different times in the past to hopefully resolve the issue, but no luck. Just today, on one of the WAP4410N's, I upgraded to the 2.0.6.1 firmware (backing up config, reset to factory default, upgraded firmware, reset factory default again, restored config). After the first reset to factory defaults, the Access Point itself picked up a DHCP address from the server, and I verified this in the DHCP console on the server, so I know that the DHCP relay is working. However, my laptop would not get a DHCP address when connecting wirelessly through that access point. It is a Windows 7 Enterprise laptop. I also could not get a DHCP IP with my iPhone connecting to wireless, to rule out specific issues with just a laptop.I have the DHCP lease times for the subnet that these WAP4410Ns are on set to 2 hours.
To put a cherry on top, there is one laptop that stays in a lab area at all times, connecting wirelessly, and it DOES get a DHCP IP address (I can see in the DHCP console that the lease for this laptop continually renews as needed). I do remember on initial config when I couldn't get it to work, that I did a manual set up, gained connection, then switched it to DHCP...but that doesn't work for any other laptop.Why would the access points get DHCP address, but not anything connecting to the Access Points?
Using WISM with 7.0.220 and 1240 and 3502 APs. Just found that some of our 3502 AP didn't enbale their clean air and CDP when installed. This only happened on a few new APs. But the area these APs where we seem to have had a few problems with PCs. The only PCs effected where Computer On Wheels (COWs), Dell 780 Desktop with a Cisco Wireless Card.
Using an interl wireless card and others in thes areas worked.Once I enabled the CDP and Clean Air, the COWs worked.My question is with the APs not having CDP enabled, could this affect the cisco wirelss card in the COWs?
I have cisco 2600 router. The problem is my router ios has been crashed and i unable to use any mode on my router. I need to install new ios. How can i install or upgrade new ios step by step.
View 1 Replies View RelatedAt my school we have a lot of access points, but sometimes the computer use the wrong access point. How can I solve that? Is there a program for switching access point?
View 8 Replies View Related
