Cisco :: Unable To Access GUI For 2100 Series WLC?

Sep 2, 2012

I have powered ON WLC(2100 Series) and connected LAN port from WLC to my PC. To access WLC GUI what is the factory default IP address?
 
I connected Console Port of WLC to Serial port of my PC. I have configured WLC as per the WLC quick guide.

Management Interface IP address :: 10.40.0.4
Management interface Net Mask: 255.255.255.0

[Code].....
 
The result is same even when below commands are used Configuration modeport adminmode all enablenetwork webmode enablenetwork secureweb enable 

View 12 Replies


ADVERTISEMENT

Cisco Wireless :: WLC 2100 Series DHCP

Sep 1, 2011

I have a problem with our WLC 2100 series (2125). Basycally internal DHCP server configured on WLC is not working. I have one AP connected to port no 7 (PoE) to bypass and eliminate problem with other equipment.
 
Port no 7 details:
 
IP Address: 192.168.30.10
Netmask: 255.255.255.0
Default router: 192.168.30.1
DHCP Server: 192.168.1.250(code)

View 14 Replies View Related

Cisco :: WebAuth Bundle Not Uploading 2100 Series

May 19, 2012

Recectly we replaced Cisco 2100 Series LAN controller to Cisco 5508 Wirless LAN controller , I downloaded WebAuth Bundle from my Old LAN Controller ,when i am trying to upload to my New Wireless LAN controller ,its not uploading and also it gave me uploading failure error message .

View 2 Replies View Related

Cisco :: Locking Down Corporate SSID Using Certificate WLC 2100 Series

Jan 12, 2013

We need WiFi security on our corporate SSIDs locked down using certificates, we are using wlc cisco 2100 series. We need these on every workstation, laptops etc.

View 6 Replies View Related

Cisco :: Configuring Trunking And VLANs On A 2100 Series Wireless Controller?

Oct 4, 2011

We have 4 1142N LAPs that I want to divide between an internal wireless and a guest wireless network using the controller.  Currently all of the APs are on an established internal network, but I want to migrate one over to a test guest network before buying more LAPs to augment the networks further. Currently the port connecting to the WCS from the 3560 switch is configured as an access port using VLAN 10.  Whenever I make it a trunk port carrying VLAN 10 as well as the other ports we will be using for the guest and ap-manager networks, I lose connection with the controller.  To me this implies that the port on the controller is configured as an access port as well.  In the documentation I found for the controller it states that by default the ports are al configured to be trunks, but it appears as though something was changed by the previous tech.  All of the APs are connected to other switches, not to the controller itself.
 
1) How can I get the port on the controller back to being a trunk port

2) Can I use the internal DHCP server for the guest network if the subnet is different than the management subnet, or will I have to use another external server and relay/proxy it through the controller to give guest clients IP addresses?

View 2 Replies View Related

Cisco :: ASA 5505 Series / Unable To Access New Subnet

Dec 7, 2011

I am working on a site that has recently added a new subnet and I am unable to ping any of the stations on this new network. I have configured an Exempt NAT rule just the same as the rules allowing access to other networks. I have a feeling the problem is in the Site-to-Site VPN configuration since the new subnet is at the primary location over the VPN.
 
In the site-to-site configuration I added the new subnet to the list of "Remote Networks" and I still can't communicate with any of the devices on the network. If I go to the main site I have no problems so it appears to be related to the VPN or a configuration in the ASA on that site.
 
A port scan shows that all the traffic is "filtered" so somewhere either the site ASA or the main ASA is blocking the traffic.

View 7 Replies View Related

Cisco :: Test Fast Roaming Using A Cisco 2100 Series Controller And 2 1140 APs?

Jul 20, 2011

I'm trying to test fast roaming using a Cisco 2100 Series controller and 2 1140 APs. The initial authentication succeeds fine and the wireless connection works ok using WPA2+CCKM and LEAP with a Cisco ACS radius server.The problem is that the client does not attempt to preauthenticate with the other AP because the RSN Capabilities IE in the AP beacons and probe responses do not set the RSN Preauthentication capable bit. I can't figure out what it takes to get the APs to indicate to clients that it can do preauthentication. I'm been crawling through all the documentation I can find, to no avail.

View 1 Replies View Related

Cisco Wireless :: Unable To Console Into 2600 And 1552 Series Access Points?

May 7, 2013

We are having a hard time to console into to the APs using the serial connection (USB to serial converter).We have tried the recommended settings (9600, 8 bits, no parity, 1 stop bit, no flow control (also tried XON/XOFF)) without any success.We are able to connect to 3560 series switches and 5508 WLCs using the same cables, notebook and application (putty, hyperterminal & secureCRT).

View 4 Replies View Related

Cisco :: Does WLC 2500 Series Supports 1262 Series Access Point

Jun 14, 2011

Does AIR-CT2504-25-K9 spupports AIR-LAP1262N-E-K9  Access Point? How can I check this?

View 1 Replies View Related

Cisco :: 2100 WLC - Guest Access / Passing AD Credentials

Aug 31, 2011

We have a building with 6 Cisco Airnet 1140 connected to a Cisco 2100 WLC, all tied into a nice Central Certificate server and a Win2008 NPS/Radius server on a Win2008 AD. Our trusted PC wireless access is fine, with domain laptops with certificates authenticating with DHCP all round the building. We use GP to apply settings to an AD integrated Proxy server for internet access.
 
The problem I now have is with guest access...
 
We are an education establishment, so students could turn up with anything from a laptop to an iPad to an Android phone, which immediately rules out using proxy PAC files to configure the proxy.
 
What I really want is a method of using the radius to verify the guest user against their existing AD user account, which I believe is possible. The one snag we have is in order to avoid the user having to configure the Internet proxy we would have to switch it to a transparent mode, which immediately restricts our ability to report on AD username, we would only have an IP address to report on, which is next to useless!
 
We've looked at a Gateway product (Astaro), which integrates the Filtering onto the Gateway, but the downside is that you have to use their APs, so we would be replicating existing work, whilst also managing two filters.

View 1 Replies View Related

Cisco LAN :: 2100 - Browser Access To Wireless Controller?

Jul 29, 2012

I have a wireless controller 2100. I can't access it via browser, when I am connected to one of its physical ports. I use the same subnet ip address as that of the management interface of the wlc.

View 5 Replies View Related

DLink WL-2100 - PC To Access Point To Wireless Modem

Apr 2, 2011

I have a D Link WL-2100 AP, I connected my PC to AP with ethernet cable, then I tried to connect the AP to my wireless modem but I couldn't do.How can I make the AP recognize wireless modem?

View 2 Replies View Related

Cisco :: Light Weight Access Point 1242AG K9 Is Not Joining 2100

Sep 4, 2012

I have configued Cisco LAP 1242AG with statis IP.I have connected LAP to WLC.I am able to ping WLC management interface IP Address from LAP's console.LAP is failed to Join WLC with  error "Could not resolve CISCO-SAPWAP-CONTROLLER"

View 3 Replies View Related

Unable To Enter 10.12 Series Address In LAN PC?

May 2, 2011

Not able to enter 10.12 series address in LAN PC

View 12 Replies View Related

Cisco :: Unable To Download 2500 Series Wireless Controllers

Mar 19, 2013

I want to download the Cisco 2500 Series Wireless Controllers Release 7.3 Software AIR-CT2500-K9-7-3-112-0.aes.I have CON-SMB for it, when I try to download it I am not to download it. I have mentioned the message given by Cisco" The category for this contract does not include the feature or the benefit for software download that you are requesting at the moment, this means that even if the contract is a support assistant (8X5XNBD) does not support the the mentioned feature for you to update the device you need, please refer to your partner directly to be able to acquired a Cisco Service Contract that supports and include the software download feature to be able to upgrade and update your device as you need."Is there any seprate contract for downloading the Software.

View 2 Replies View Related

Unable To Connect To The Wireless Router To HP G-Series Laptop?

Mar 16, 2012

I can not get my new hp pavilion g series laptop to connect to the wireless router that I currently have. What do I need to do?

View 1 Replies View Related

Cisco Routers :: SRP 500 Series Gain Access From One IP Address With NAT

Nov 15, 2012

Normaly all incoming IP addresses can use NAT to gain access. I would like to make a rule that only one IP address can connect to my router and use that port or range of ports defined.
 
Is there a way to configure a SRP 527W on such a way?
 
If not possible now, can I expect a software update ?

View 3 Replies View Related

Cisco WAN :: Switches 2960 Series No Internet Access?

Mar 29, 2011

I have a problem I have Cisco 2960 series switches with ip address 10.10.10.2 255.255.255.0 works but can not connect to the Internet

View 1 Replies View Related

Cisco Wireless :: Controller 4400 Series Work With Aironet 3600 Series

Mar 6, 2012

Can Controller 4400 series work with Aironet 3600 series?

View 5 Replies View Related

Cisco WAN :: Can't Use Ehwic-3g-hspa-u Card In 2800 Series And 1841 Series Router

Jun 2, 2012

why I can't use cisco ehwic-3g-hspa-u card in cisco 2800 series and 1841 series router?documentation said that it should work with that devices but when I installed it, it doesn't work even as device i can't see I am using cisco latest ios  advance ent. 15.1(4)M4?

View 3 Replies View Related

Cisco Wireless :: 1140 AP Series Vs 1260 AP Series Technical Differences

Jul 24, 2012

What's the main technical differences among the 1140 AP series and the 1260 AP series?I know that the 1260 supports external antennas while the 1140 supports internal antennas, but apart from that, is there any other important difference ?

View 10 Replies View Related

Cisco Routers :: How Does Quality And Longevity Of SRP500 Series Compare To RV Series

May 27, 2012

My Draytek 2710 just dies after 2 years so I was looking for something a little more reliable and noticed the spec of the SRP527W-U.I take it with only one antenna and reading a couple of past discussions, the wireless will only manage n-lite as some people call it i.e. 150Mbps, and not the full 300? Oh, and are the ports still only 100M and not Gig?I know the 547 would tick both these boxes but we are talking twice the price.  How does the quality and logevity of the SRP500 series compare to the RV series (which would need an adsl modem) or the Linksys boxes?

View 1 Replies View Related

Cisco Wireless :: Configuring Access Point Of 1200 Series?

Apr 19, 2012

I recently purchased a Ciso 1200 Series WAP and I want to bridge this to my existing Cisco Wireless Router So I can extend my coverage. I have done some research but keep coming up short as to where I need to start. Note*(I do not want a physical connection to the WAP, I simply want to be able to bridge the connection from my existing Wireless router to my WAP.

View 1 Replies View Related

Cisco Wireless :: AP500 Series Access Points Range?

Oct 7, 2011

I am recently engaged by a client to convert his network to wireless network. My client operates in an office with 8 floors and also concrete walls. On making my research i came about your product Cisco AP500 Series Wireless Access Points.I will like to know if this product can work for my client perfectly or I will need to get other enhancement to make it work at its optimum.

View 2 Replies View Related

Cisco Wireless :: Will 3500 Series Access-Points Work

Jul 14, 2011

I have a customer who bought Cisco Aironet 3500 Series. Currently 4404 WISM Controllers are installed with 1142 Access-Points. The WLC-Version is 6.0.199.

Will the 3500 Series Access-Points work? (Of course without the spectrum intelligence feature)?
 
The Q&A says the following: Are there any concerns with supporting the new Cisco Aironet 3500  Series Access Points with the older Cisco 2000, 2100, 4100, or 4400  Series Wireless LAN Controllers?

View 2 Replies View Related

Cisco :: Setting Up Aironet 3500 Series Access Point

Nov 21, 2012

links with information / guidelines for the initial setup for this Access Point?

View 7 Replies View Related

Cisco :: How To Integrate WLC 2100 With ACS 5.0

Jan 17, 2011

i have a cisco ACS version 5.0, I need to authenticate a wireless users connected to WLC 2100 controller when i connect the controller to a Dot1x port in the switch , the port go down.

View 6 Replies View Related

Cisco Wireless :: How To Connect Macbook Air With 1100 Series Access Point

Oct 10, 2011

how to connect macbook air with cisco 1100 series access point

View 2 Replies View Related

Cisco :: Design Will Include 5508WLC And 3600 Series Access Points?

Apr 11, 2013

We are re-designing our wireless network and are navigating the security options.Are design will include a 5508 WLC and 3600 series APs. We plan on breaking our wireless out into four VLANS.Is 802.1x the standard for wireless authentication?What EAP flavor would you recommend for wireless? We will be supporting an environment with a variety of mobile devices (iPhone, iPad, HP tablets, Dell laptops, etc.). We will also be supporting wireless Cisco VoIP phones. Someone suggested choosing between EAP-Fast or EAP-PEAP, does this seem reasonable? Also, if we want to authenticate users using their AD account, we need to have NPS running on the AD server and use the radius protocol from client to server, is that right?

View 1 Replies View Related

Cisco Switching/Routing :: 800 Series - Limit Monthly Traffic On 3G Access

Oct 29, 2012

Is it possible to configure a limit on monthly traffic over a 3G access on a Cisco 800 Series?
 
The scenario is that a customer has a Cisco 800 3G routers with a 3G card from a Service Provider, that offers a rate for X Mbytes per month and that when those monthly X Mbps are exceeded, a differente rate (much more expensive) is applied for the excess traffic that month. The customer would like to have the router NOT to active the 3G access when the X Mbytes (on that month) are exceeded. Maybe this is possible to implement using a TCL script and ip accounting?

View 1 Replies View Related

Cisco Wireless :: 3602i Series Access Point Gives All Junk Values

May 16, 2013

Access point gives all junk vlaues in console.   I am getting all outputs while booting up and executing commands. But To say, it is as simple as printing with spelling mistakes

View 2 Replies View Related

Cisco Wireless :: Aironet 1100 Series / IOS Upgrade For Access Points?

Sep 25, 2012

I have some Cisco Aironet 1100-series, 1040 series, 1240 series, 1130 series and 1200series and i would like to upgrade them to the newest ios software.
 
The IOS that are present in my access points are 12.3(8)AJ and 12.3(11)JX.

View 2 Replies View Related

Cisco :: Changing Password On WLC-2100?

Aug 31, 2011

I am currently running WLC - 2100 with software version : 7.0.98.0
  
My question is :
 
How to change the existing password ( not reset )  but change the password with the web interface ?
 
If that cant be done, then my guess is I have to do it via telnet/ssh session

View 4 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved