Unable To Access Linksys Console
May 2, 2012
I have linksys ADSL Router which is having one line port for Phone Line and 4 Ethernet Ports.The Router IP is 192.168.1.1. When i connect this Router through one of its Ethernet Port to one of the Network Point(which is DHCP enabled)is working fine. I get the IP 192.168.3.x from my existing DHCP not from the ADSL Router which is enabled.Secondly, Although i can Ping the Router IP 192.168.1.1 from Wifi client 192.168.3.X, But when i try to open the Router Console a Login window open and is says " your are trying to access the Router in an insecure ways and it doesnt not authenticate ID and PWD.When i directly connect Router to my Laptop then am able to do so.
View 1 Replies
ADVERTISEMENT
May 2, 2012
My Linksys Routers IP is 192.168.1.1 am unable to access the console, although i changed the computers IP 192.168.x.y. i have tried by Hard Resetting the Router but still the same?
View 1 Replies
View Related
Jan 18, 2013
Although I hasten to point out that I have owned and used an 'IBM' type PC since 1988 and have always managed to get things configured correctly until NOW!
Apart from the last time I tried to use a Linksys product. I had the WRVS4400N recommended to us by a friend as we run a small FTP server to share promotional materials amongst sales operatives around the world, wanted to protect it from intrusion and was told that a Cisco Linksys product with a VPN was the way to go.
I duly purchased a WRVS440N and have been trying to log into the admin console via both browsers (IE9 and Google Chrome) that are installed on a laptop running Win7 which in turn is the only thing connected to the stated device via ethernet port 1... I have tried accessing it via http://192.168.1.1 and have even tried a suggestion from another forum to try https://192.168.1.1 - this only results in my being told that the address does not have a trusted certificate and I even tried every suggested workaround...
I have tried all kinds of reset periods from 10 seconds to a minute, both hot and cold and each time the result is the same - I type in 'admin' and 'admin' in the appropriate boxes and the dialogue box continues to return to the browser window with empty fields...
The shame is that I have managed to re-flash a BT Voyager 190 ethernet modem successfully with DynaLink v3.29a firmware (which allows it to be used with any ISP besides AOL [for whom this modem was solely intended]) and can set it up as a DHCP server, non-DHCP with a single link to another server or non-DHCP and no link.... The point is the modem works... I'm using it right now to type this! We have a single static IP from our ISP and the BT modem is working just fine (as is the TP-Link wireless modem/router that the WRVS4400N was intended to replace)... there are other options in it's firmware for port forwarding, etc and I'm convinced that it wil be adequate for use in conjunction with the WRVS4400N.
I have to concede that the WRVS4400N was not sold to us as NIB; it was sold as re-conditioned and was shipped to or via Ingram Micro Distribution from Cisco Systems, Veldweg 3, Herkenbosch 6075 NL (Holland) via UPS on or about the 31st of July, 2012... there is a shipping label on the original packaging that tells me that so it has in fact been back to Cisco at some point and for some reason.
View 3 Replies
View Related
Aug 15, 2011
I am having FWSM in active /standby mode deployed on two different cat 6k chassis. Unable to access the fwsm module from switch using ' session module mod_no processor 1 ", it throws error " % telnet connections not permitted from this terminal" Running Version 3.2.6 on fwsm, Cat 6k is running 12.2.33.SXH1,
switch#session slot 3 processor 1
The default escape character is Ctrl-^, then x.
You can also type 'exit' at the remote prompt to end the session
% telnet connections not permitted from this terminal
---------------------------------------------------------------------------
have allowed telnet on line vty, configuration on Line vty is simple allowing all transport protocols
line vty 0 4
exec-timeout 5 0
transport input all
transport output all
line vty 5 15
exec-timeout 5 0
transport input all
transport output all
View 3 Replies
View Related
Dec 27, 2012
I have 2960 switch and i can't access it using my console cable .I can access other switches in my network ( 3560 & 2960 ) but i can't access only this switch.may be the console port in the switch damaged? or it's a bug ?? !!! although the switch is worked normally.
View 11 Replies
View Related
May 7, 2013
We are having a hard time to console into to the APs using the serial connection (USB to serial converter).We have tried the recommended settings (9600, 8 bits, no parity, 1 stop bit, no flow control (also tried XON/XOFF)) without any success.We are able to connect to 3560 series switches and 5508 WLCs using the same cables, notebook and application (putty, hyperterminal & secureCRT).
View 4 Replies
View Related
Jan 11, 2012
I not able to access cisco 2811 router (AC operated) through console port when I try to access it by selecting COM Port, but I able to access by selecting the TCP/IP option.
View 5 Replies
View Related
Jun 13, 2012
I'm using Linksys WAG200G Wireless modem and connection mode is "Bridge Mode Only", in this mode I'm not getting the 192.168.1.1 setup console and Wifi facility.
View 3 Replies
View Related
Feb 11, 2013
i have been facing this problem as i cannot see any log messages via my console port,except by looking at logs manually by "show log" command,
View 3 Replies
View Related
Aug 9, 2012
I have a 6513 with redundant sup 720-3B's that I cannot get onto. In short, one of the power supplies failed, it still passes traffic but I can't console or ssh to the box. Other than the two sup 720's, I have a 4 port 10gig card, a 16 port GBIC Card and an IDS module. I have tried removing the 10Gig, IDS and one of the sup's but still don't get anything on the console. I have rebooted the entire chassis and don't get anything on my console while booting. I have tried changing the speed of my terminal to every setting available incase someone has changed it at some stage but to no avail. I have tried swapping sup's, using only one at a time in the chassis but not getting anything. Is there anything else I can try to get onto this chassis? The power supply is a 3000w with a 32amp input. The failed power supply had tripped a switch, when i brought it back up, the power supply came out but the output failed LED is on. My #questions are, is there anything else I can do to try get onto the console, and is the power supply goosed when the RED LED is lit? I have reseated the power supply also but the same result.
View 2 Replies
View Related
Sep 10, 2012
I have stack of 2960 S switches.I can console only from Master not from memember switches is this default behaviour?
View 1 Replies
View Related
Jan 25, 2012
I use a C2950-24 switch, with IOS 12.1(22)EA12 release.When I try to connect in console mode, I can see the "Press RETURN to get started!" message, but it's not possible to me to have the # prompt.An "authorization failed" message is displayed. And the same message is prompted.
I try to recover password by following the recovery procedure. After the boot command, I never see the message "Continue with the configuration dialog? [yes/no]: ".
View 6 Replies
View Related
Oct 23, 2012
I have a set-up with multiple C2960 and C3750 switches. All these devices are being managed remotely. So basically I login to C2901, which is used as a Terminal Server, and reverse SSH to the console of each device. That's - I have assigned an IP to each port of the terminal server so that I can SSH directly to the desired device through via the mapped IP.
Now, recently I had to restart couple of switches - one C2960 and C3750. I initiated the reboot via console connection remotely. I could see the device logs for some time and then the logs stopped and there was no reaction from the console irrespective of any command I tried to enter.
I tried resetting the line on the terminal server, but that didn't work.
Now when I try to SSH the IP mapped to console of that particular device - i dont get any login prompt and there is no effect on device after giving any command. Although i can see the logs on the console session - but cant do anything.
I have a second way of connecting the device via inband- management, and checked the device config found it correct. It is same as other devices which are working correctly.
Both C3750 and C2960 are behaving exactly same - can see logs on console but see effect of even pressing enter - not getting login prompt as well.
View 4 Replies
View Related
Mar 12, 2012
I have a strange issue that I am having an issue figuring out. I am trying to login to the 1941 router through the console port. When I enter the username and password, which I just set, it fails. I am able to login under a different login but when I try to enter the enable mode the enable password doesn't work, which I just set as well. I can login with the TACACS+ login from a SSH session. Here is the line config:
line con 0
exec-timeout 15 0
logging synchronous
[Code].....
View 5 Replies
View Related
May 10, 2012
I have 2691 router with following config
line console 0
login local
password xty
When i remove the login local from the line console i connect to console port and press enter it shows router prompt 2691Router> but i am unable to go to enable mode.If i telnet to router then i put username and pw then it goes straight to enable mode.
vty config is
line vty 0 4
exec-timeout 600 0
logging synchronous
login local
length 500
transport input telnet ssh
escape-character 3
Any reasons why i can not go to enable mode by console?
View 3 Replies
View Related
Jan 14, 2012
I am not able to access my wireless access point anymore. I tried to access the web configuration in my browser as I have in the past 192.168.1.245, but I have no luck there. I tried to reset it by holding the reset button for 10-30 seconds, and I have no luck with that. What I have noticed on the AP is that the ethernet light keeps going out. The only light that is lit on my AP is the power and sometimes the ethernet light. My AP is connected to my router which I am able to gain access to the internet from any devices connected to the router except the AP. I have a router (E2000), a WAP4400N, and switch. I want to keep my wireless access separate from my business network. I cannot get my WAP4400N to work anymore.
View 1 Replies
View Related
Jan 3, 2011
We forgot the IP address of this WAP, and resetting the router doesn't take it to the default IP, no matter how I try to reset it. The SSID (and WEP key) stays the same too, which makes me wonder if the reset button is even working. We can still connect computers wirelessly through it and have them access the internet. Our issue is we need to change the SSID. Right now it just connects people invisibly - it gives them IPs from the subnet it's attached to, and yet the various DHCP servers I've connected to never show it as having its own DHCP address.
View 1 Replies
View Related
Apr 19, 2013
I have a problem with my vpn concentrator. I cannot access it through console, I have tried every baud rate that is available on my SecureCrt but it won't display anything. At first, I thought that my console cable is defective but I was able to access a WLC via console cable together with the rj45 to db9 converter. I also tried connecting the vpn concentrator to a switch and enable the cdp in the switch but the "show cdp neighbor" can't detect or display the vpn concentrator even if the interface status is "up up". Is it safe to say that the VPN concentrator is already broken?
View 1 Replies
View Related
Sep 4, 2012
but is there anyway to access directly a LAP 1522 using a console port?
View 5 Replies
View Related
Apr 9, 2013
I can access the web console, and also have telnet access but only to a VT100 menu system - How do I access the full console command prompt (without using the serial console connection)?
View 4 Replies
View Related
Jan 4, 2013
I can not access the switch through the console. The web interface is working properly.
Model: SRW224g4
Below some pictures. The Hyper Terminal settings. Error:
View 6 Replies
View Related
Jun 14, 2011
we have two pix535 one is ur other is FO license.
once a time i found can't access FO pix535 console, i'm sure console cable is ok. when i unplug failover serial cable from FO pix535, i can access pix 535 console.
View 3 Replies
View Related
Feb 9, 2012
I have an asa 5585x cluster. I get ssh access but no console access on the standby unit.
On the active unit, when I try console access, ASA ask for a password. I have tried all the one that I have configured, but without success.
View 5 Replies
View Related
Feb 29, 2012
today I received a Cisco 1841 Router with a problem i have never seen before. Maybe this my 1st really,really broken Cisco Router. When I power the Router on, the fan and all lights turn on (green) and that's it. Nothing changes, also after minutes of wating. On console i don't get any messages and I already tried every BAUD rate possible. Switched the router off/on again and again. And no, it's obviously not a console problem of my computer, because i tried with different routers.
View 3 Replies
View Related
Jun 30, 2012
I just purchased a used Catalyst 2900 XL switch and have not been succesful in connecting to the console via minicom 2.5 running on Ubuntu 12.04 or 11.10, I don’t even get junk charecters in the terminal or echo on input. The switch passes POST according to the LEDs on the front and the network ports are fucntional for switching purpouses.
I’m using a Prolific PL2303 USB-Serial adapter, which works with minicom to console into another device. I’ve tried every baud rate available and tried combonations of hardware flow control, software flow control, and niether.I’ve tested the pinout of the console cable and all pins map correctly according to Cisco spec.I’ve also tried Cutecom, putty, and screen. I have not tried HyperTerminal because I do not use windows.Is it possible that the previous owner disabled console access? Do I need to reboot the switch each time I test a different baud rate?
View 4 Replies
View Related
Aug 29, 2009
I just bought an LG Bluray DVD player (BD390) which is unable to find the access point in my home network.My router is a WRT54G, ver. 2.2, running firmware: Ver.4.21.1. My home network uses high speed cable with two computers on the wireless network, all working with no problems.The router is on the second floor but the two computers and the new BD390 are on the first floor - about 35 feet away. I have the wirelss security set to none and use only the specific computer MAC addresses to allow connection to this network.
I found directions in the forum for a setup using the LG BD390 but with a different Linksys router. I changed the security to WPA (AES); the Beacon interval from 100 to 75; the Fragmentation Threshold from 2346 to 2304; and the RTS Threshold from 2347 to 2307. The DVD wireless connection still failed to find my network. There is a "Push button" connection feature on the BD390 setup which I tried, but the only "button" on the router I could find was in the basic wireless setting, a green icon for the wireless SSID setup. No connection was made there either.
The recommendation connection from the LG manual is for a network cable, but that would be over 50 feet and a real pain to connect, so I would prefer WiFi.
View 3 Replies
View Related
Aug 26, 2011
Few months back i had upgraded my Lynksys router with Coova AP firmware. Everything was working fine.I had configured the AAA server on CoovaAP and was able to access the internet.I had configured the user name and password as a "testuser" and "password" respectively. With that user id i used to access the Coova AP router and internet. Now i want restore the WRT54GL firmware on Lynksys router. But with the used id and password which i had configured the router is not at all accessible. So i did 30-30-30 reset on the router 2-3 times.
Now i can see openwrt login page with 192.168.1.1 IP address. It is asking for user id and password. I tried all the combinations of user id and password, but no luck. I browsed some link on the internet and some people have recommended that default user id as a "root" and blank password. But with that also the router is not accessible. I cant to do much on the router untill i will log in to router. I have spent lot of time on this.
how to restore back the original WRAT54GL firmware on my router. Anyhow i want WRAT54GL firmware on Lynksys router. Can somebody tell me how to achieve this?? Or atleast what user id and password should i try to log in to router?I tried to use telnet command on the router (Connected router to linux based computer with ethernet cable). But telnet also not working. It is not asking for password, and it saying disconnected.
View 1 Replies
View Related
Aug 26, 2011
I had configured the AAA server on CoovaAP and was able to access the internet.I had configured the user name and password as a "testuser" and "password" respectively. With that user id i used to access the Coova AP router and internet.Now i want restore the WRT54GL firmware on Lynksys router. But with the used id and password which i had configured the router is not at all accessible. So i did 30-30-30 reset on the router 2-3 times. Now i can see openwrt login page with 192.168.1.1 IP address. It is asking for user id and password. I tried all the combinations of user id and password, but no luck. I browsed some link on the internet and some people have recommended that default user id as a "root" and blank password. But with that also the router is not accessible. I cant to do much on the router untill i will log in to router. I have spent lot of time on this. How to restore back the original WRAT54GL firmware on my router. Anyhow i want WRAT54GL firmware on Lynksys router
View 4 Replies
View Related
Sep 17, 2008
I'm trying to access the WAP200 for the first time. Instructions say Configure your PC to have the static IP address on the same subnet as the Access Point's default address (http://192.168.1.245). So I assumed i would go to TCP/IP properties and type in IP address and subnet mask and the Utility would open.
View 3 Replies
View Related
Jun 15, 2012
Just got a new hard drive installed on my laptop, and now for some reason I can not access my router. I am connected to the internet, and everything is fine there, but when I type the 192.168.1.1 and enter admin as the password, it shows that I am unauthorized.
I have a Linksys E4200 router
View 2 Replies
View Related
May 4, 2013
after updating to smart wi-fi I can't access the USB FTP or off network.Only way it's accessible is from the computer the router is attached to via network drive.FileZilla gives me this error....."Connection attempt failed with "ECONNREFUSED - Connection refused by server".I've reset the router same problem.
View 9 Replies
View Related
Jul 20, 2011
I cannot access this router. I have a cable modem from Comcast Is there any way to clear info, I have reset 50 time and it will ask for uname & paswrdWhat shall I do?
View 1 Replies
View Related
Mar 22, 2011
I've recently purchased 5 WAP610N access points to replace my older US Robotincs access points.I've configured one WAP610N (upgraded to the latest firmware i found on the site) with a static IP, bropadcasted SSID & WPA2 personal security.I had no problem at all to connect PC's but when i tried to connect the Ipad & Iphone (with the latest 4.3 firmware) i was able to connect to the network but unable to get an IP lease.
I had no problem before connecting to the US roboticx access points.When i change (lower) the security to WEP on the WAP610N then everything works fine but i want to use WPA2 in stead of the unsecure WEP protocol.
View 1 Replies
View Related
