Cisco :: Access Directly LAP 1522 Using Console Port?
Sep 4, 2012but is there anyway to access directly a LAP 1522 using a console port?
View 5 Replies
ADVERTISEMENT
Cisco Wireless :: AIR-LAP 1522 To Connect To Console Port
Sep 5, 2012They brought me a LAP1522 referring that it is not working properly. I am trying to connect to console port but the problem is that I only get log messages but I cannot edit something or type any commands. I have attached the log messages if you can catch something from there. Ignore the messages about not finding controller because the AP has been removed from the real network to my office.
View 14 Replies View RelatedD-Link DAP-1522 :: Do Devices Talk Directly
Apr 14, 2013Do the devices connected to the DAP-1522 communicate directly with each other or do they communicate through the router.My DAP-1522 is set up as a bridge connected to my DIR-825. The reason I ask is I've set up an HTPC connected to the DAP-1522 and I also have media devices connected to the DAP and am wondering if they'll communicate with each other directly or if they have do it by going to the router and back. That way I can use my HTPC to serve media to my devices at local speeds.
View 1 Replies View RelatedCisco Switching/Routing :: Unable To Access C2811 Router (AC Operated) Through Console Port
Jan 11, 2012I not able to access cisco 2811 router (AC operated) through console port when I try to access it by selecting COM Port, but I able to access by selecting the TCP/IP option.
View 5 Replies View RelatedCisco Switching/Routing :: 1700 - Setup For Connecting Router AUX Port To Switch Console Port
Feb 26, 2012I was looking for a way to connect an AUX port from a 1700 router to a 6500 switch module console port, to see the output of the Switch's on the 1700 router, in case there is a network downtime, I could see what's going on in the switch, what cable should I use ? Also, is there is any kind of documentation for this type of config what have I seen is very few info.
View 2 Replies View RelatedRouters / Switches :: Plug A 8 Port Switch Directly?
Sep 27, 2011I have a Modem/Router combo and am trying to plug an 8 port switch directly into it and then have wireless AP's and other hardwired devices plugged into the switch. Normally, when I plug a switch into a router it requires no set up. This one on the other hand, will not work.
View 7 Replies View RelatedPort Forwarding Setup - Remote Directly Into One Of Servers?
Jan 19, 2012I have a small network in my garage, it's basically made up of a bunch of test servers. Those and a win xp machine are all hooked up to a switch, and the win xp machine also has a wireless usb stick that is connected to my wireless router, and is being used to share internet to the rest of the machines. The test servers along with the NIC card on my win xp machine sit on a different subnet, however.When I remote into the win xp machine from my house, i can run a second remote desktop in the first session, into any of my servers. I want to do work on them, but its very laggy.
Is there a way I can setup a port either on the win xp machine or my wireless router so that i can remote directly into one of the servers? so if the win xp machine has a wireless ip address of 192.16.13.102, and one of the servers on the 2nd subnet has an internal ip of 192.2.2.4, can i have it so i can make, for instance, 192.16.13.102:6333 forward to 192.2.2.4? If not, is there any other way i can directly remote into one of the servers, by passing the first remote desktop into win xp? What settings would have to be the same across the line?
D-Link DIR-655 :: Connect 3g USB Modem To Router Directly Through Usb Port?
Jan 24, 2013Can i connect my 3g USB modem to my dlink router directly through the usb port.
View 10 Replies View RelatedCisco LAN :: AS5350 Can't Connect With Console Port
Jun 22, 2012I had a Cisco AS5350 , and it works correctly through the year. but now I could not conncet to it even with console cable .my windows is server 2008 ,COM1,9600, but in hyper terminal I couldnt see anything from cisco,even I have change my console cable , but it still doesnt work.
View 11 Replies View RelatedLinksys Wireless Router :: E3000 Disconnected / Connect To PC Usb Port Directly
Jul 26, 2011I have external hard drive connected to E3000. It is formatted as NTFS and working fine. However if I disconnect from router and connect to PC usb port directly, I get a message that hard drive needs to be formatted.
View 2 Replies View RelatedCisco WAN :: 2911 Console Port Giving No Response
Apr 6, 2012I have a brand new 2911 router out of the box. I attached a terminal to the console port and watched the bootup sequence. I get the "press return to get started" at the end but I can't get any response. I just used the same cable and terminal on a 3750 switch and an ASA. What am I missing?
View 3 Replies View RelatedCisco Infrastructure :: 6509 Console Port Not Working?
Jan 27, 2003We have a 6509 running 5.4(2). We have set up a hyperterm session and connect to multiple devices, then we get to the 6509 and it will not work. When we reload the 6509 and we are consoled into it, we get data until it is finished reloading. Then the console connections is no longer there.
View 5 Replies View RelatedCabling / Cards :: Connect To Cisco Console With / Without PC Serial Port?
Jan 5, 2012I need to connect to the console port on a cisco firewall, an rj-45 connector. The cable is a rj-45 at one end and a serial on the other. My PC has no serial port and I am unable to use the provided cable to connect to the firewall appliance. Is there software that can allow serial over my PC's Ethernet? I really don't have time to order a serial card for my PC.
View 1 Replies View RelatedCisco WAN :: SG500-28-K9-G5 Weird Symbols When Trying To Connect Through Console Port
Feb 18, 2013I have a SG500-28-K9-G5 at work and I'm tyring to connect to it trough the console port via Putty and get wierd symbols: When I press any button I see alot of wierd symbols comming up, for example if I press shift+6 or Enter (or anything). [code]
View 2 Replies View RelatedCisco Firewall :: Brand New ASA 5510 Console Port Not Responding
Jan 17, 2013Any one experience with this issue that cannot access to console port. USB serial cable and terminal server working fine with all other ASA 5510 except one of them. I rarely see the console and aux port failed to response.
View 2 Replies View RelatedCisco Switches :: Configure SRW248G4 Switch Through Console Port?
Jun 2, 2013I want to configure my SRW248G4 switch thru console port. Unfortunately in this switch there is no RJ45 console port input, I can only see cosole port that is look like RS232 input. I bought two standard cisco console cables that have one end with db9 and one with RJ45.
Now I have and idea to put one end of one cable (db9) to switch, and one end (db9) of second cable in my computer (COM input/output)
I need to connect two RJ45 together - this is not a problem, I know how to do this. Here is the question :I know how pinout in my computer look like but i can't find pinout of console port in my SRW248G4. There is many pictures in Internet, for many Cisco devices but this isn't working. Maybe in LINKSYS pinout look different ?
Cisco Switching/Routing :: 2911 - No Response From Console Port
May 3, 2013I attached the terminal to the console port to watch the bootup sequense, but nothing appear the same cable used on athor switches and router without any issue.procedure to access the router noting that Giga ports not working also.
View 2 Replies View RelatedCisco Switching/Routing :: 2801 Router Console Port Not Working?
Feb 13, 2013I have issue with Cisco Router 2801's Console Port. My student was doing a lab and he said during configuration, Console Port stopped responding. He was in middle of configuration, so now at present, only telnet is able to login on "R2>" user mode, enable password is not set, so getting "R2>en % No password set R2>" I have tried different terminal software but no output from Console Port, changed the Console Cables, replace with working console cables, change speed (baud) settings. Also tried to connect same console with "AUX" port and got same error mentioned above. AUX Port responds but I am not able to change mode (R2#) because of incomplete running-config. it seems "Console Port" is physically damaged.
View 4 Replies View RelatedCisco Switching/Routing :: 2924 Switch - No Response From Console Port?
Dec 11, 2011I have 2 Catalyst 2924 switch in a home lab. Both of them have developed the same problem at the same time (strange). I have tried all that I can think of. I can telnet to them but cannot access via the console port. On a telnet session I execueted a "write erase, reload" on one of them. As I anticipated this threw me out of the telnet session and I presently have no access to that switch.
The console cable is fine, works for all other devices.
Cisco Switching/Routing :: 3560Gs / 4900Ms / Starting SSH Session From Console Port?
Dec 29, 2011I console into switch 1 (or router, it doesn't matter) and everything is fine. From that session I SSH to switch 2 (or router). The session on the second device has a noticable delay when I type.Next I SSH to switch 1, then SSH to switch 2 from that session. Everything works fine.Finally, I console to switch 1, and telnet to switch 2. There is no delay.So it appears the delay only occurs when I open an SSH session while consoled into a device. It didn't matter what switch 1 and switch 2 were - I had 3560Gs, 4900Ms and a 3845 router. There's no special configuration on the console or vty ports - when I do a "show line console" and "show line vty 0" the output is basically the same.
View 2 Replies View RelatedCisco Switching/Routing :: Unable To Login Through Console Port On 1941 Router
Mar 12, 2012I have a strange issue that I am having an issue figuring out. I am trying to login to the 1941 router through the console port. When I enter the username and password, which I just set, it fails. I am able to login under a different login but when I try to enter the enable mode the enable password doesn't work, which I just set as well. I can login with the TACACS+ login from a SSH session. Here is the line config:
line con 0
exec-timeout 15 0
logging synchronous
[Code].....
Cisco Switching/Routing :: VS-S720-10G - Key Sequence To Go Into ROMmon From Console Port For VSS System
Jan 19, 2012What key sequence to go into ROMMON mode from the console port for VSS system with 2 VS-S720-10G?
View 3 Replies View RelatedCisco Switching/Routing :: 6509E / SUP720 (Standby Hot) - Console Port Indicate Software Crash
Oct 28, 2012I have one Catalyst 6509E chassis and two SUP720. The bootup sequence on SUP 720 (standby hot) failed . Messages that appear on SUP 720, on the console port indicate o software crash. I don't have a flash card in SUP720.
This is the bootup process:
System Bootstrap, Version 8.5(3)
Copyright (c) 1994-2008 by cisco Systems, Inc.
Cat6k-Sup720/SP processor with 1048576 Kbytes of main memory
[code].....
D-Link DAP-1522 :: No Internet Access With It
Nov 29, 2010I have a DIR-655 router with a DAP-1522 connected in bridge mode. The firmware on the router is 1.21 and the firmware on the bridge is 1.21. I have my SSID set to broadcast on the DIR-655 with WPA-Personal encryption. When I initially setup the DAP-1522, I was able to access the setup page and connect to the DIR-655. On the status page of the DAP-1522, wireless radio is enabled and status is connected. I connected my XBOX 360, Sony BR player and DirecTV DVR to the wireless bridge and none of them can connect to the internet.
I can wirelessly access the bridge's IP, 192.168.0.50, from any computer connected to the DIR-655 but when I attempt to access the internet on any device connected to the DAP-1522, I do not get a connection. On the XBOX 360 I cannot connect my live account. On the Sony BR player, I get a message that new firmware was found, but when it attempts to connect to the internet to download it, the connection times out. Same occurs when attempting to access the internet on the DirecTV DVR receiver.
D-Link DAP-1522 :: Unable To Access It
May 25, 2012More that a year ago, with guidance from D-Link Customer Service, I performed setup on a system consisting of a DSL-2640B (with wireless disabled) and a DAP-1522 as an access point. I included the 1522 so as to have an N network, since the 2640 is G. The system works fine and I'm able to stream via the 1522 to an N 300 USB Adapter. Internet access is fine, and I'm able to access the 2640 with no problem.I want to add another 300 in a different location. To do that, I'll need to access the 1522 from my Windows 7 computer, since I've lost the passphrase that I'll need for the 300.Everything that I've read tells me to connect the 1522 directly to my computer via cable and to temporarily change the network adapter settinge to:
IP = 192.168.0.x various sources list values of 2 and 99 for x
Subnet mask = 255.255.255.0
Gateway = 192.168.0.50
Then to use a browser window to go to 192.168.0.50 Regardless of the settings that I use, the browser (IE9) always indicates that it can't connect with that address. accessing the 1522, or on any alternative way to obtain the passphrase.
Connecting Access Switches Directly To Core Switch?
Apr 30, 2011Is this a good idea to connect access layer directly to core layer with fiber and omit the distribution layer?
View 2 Replies View RelatedD-Link DCS-942L :: Access Camera Directly And RTSP?
Apr 6, 2012I can access my DCS cameras directly using several iPhone apps such as IP Cam Viewer Pro. Is it possible to access the camera directly using a web browser (I have tried without success) e.g. do you need to use a specific port?Also, the DCS-942L has RTSP. I am not clear as to the difference between RTSP and HTTP streaming of video, any resource that clarifies with respect to D-Link cameras?
View 2 Replies View RelatedCisco Wireless :: Access Points Are Directly Connected To 2016 WLC But Not Functional?
Jul 17, 2012access points are directly connected to 2016 wlc.Event log from the wlc
AP event log download completed.
======================= AP Event log Contents =====================
*Mar 1 00:00:30.157: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:00:30.161: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Mar 1 00:00:30.190: %LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar 1 00:00:30.191: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
[code]....
but still access points are not functional ?
D-Link DAP-1522 :: No Internet Access With Connection To DIR-655
Aug 29, 2012I have a DIR-655 set up as follows: [code] Lost Internet Access on my DAP-1522 on only my wireless laptop connection, but not other wireless nodes on the DAP-1522.I have most of my wireless nodes attached to the DIR-655, which is upstairs. Downstairs is where the DAP-1522 is located. There is a wired connection between the DIR-655 and DAP-1522. The DAP-1522 is being used as a Access Point. On this I have only three nodes that are wireless. My Smartphone, iPad and my laptop. There are also three nodes that are using the wired ports with no issue accessing the internet. The setup above have being working for over two years with no issue. Then three days ago my laptop connects to the DAP-1522, but has "No Internet Access." If I change my wireless connection to the DIR-655 on my laptop, then I do have internet connection. My Smartphone and iPad still are able to access the DAP-1522 and get the internet.
I have deleted my DHCP Reservation for only my laptop on the DIR-655. Wireless connection to the DAP-1522, looked at the DIR-655 and see that DHCP Reservation show the MAC of the laptop and I Reserve it. Still "No Internet Access." On the DAP-1522 it does show that my laptop is associated to this device. I cannot ping my local LAN IP Addresses , a website or Public IP Address only from the laptop. The DIR-655 shows a "Do Not Enter: Wireless system with MAC address 4025C2B97110 disconnected for reason: Received Deauthentication" with a connection to the DAP-1522, but shows "Do Not Enter: Wireless system with MAC address 4025C2B97110 secured and linked" with a connection to the DIR-655.
Cisco Wireless :: Configure AP 1522 To Accept Client Access On 2.4 And 5.0 Ghz?
May 5, 2013 how to configure AP1522 in my possession.
I have 2 AP1522 and I have to configure them so that clients can connect either 2.4 GHz or 5.0 GHz. Each of the two AP1522 must be autonomous, but has to bear in mind that are close together.
To do this I have:
- Defined the two AP1522 as RAP mode
- Set the flag on the "client access on backhault link", but I have not enabled the sub-flag "Extended backhaul Client Access" (what is this sub-flag?)
- Set 2 BGN different (but this is indispensible or I can put the same BGN? what is the difference?)
- Set the two AP1522 on two different channels (but this is necessary? or is importan only if I set the same BGN?)
- The two AP1522 appear on the WLC as a way bidge (is correct?)
How can I check if my laptop will connect using the 5.0 GHz?!? It's just turn off the antenna of 2.4 GHz?!? On my laptop I haven't found a way to force it to connect in 5.0 GHz.
D-Link DAP-1522 :: Can't Access Wired WNDR3700v2 Device
Dec 11, 2011I have 4 DAP-1522's bridging to a WNDR3700v2. Any device plugged into any of the 1522's can access the internet and can access shared drives etc. on any other device plugged into any 1522. I can access the WNDR3700 admin website from a device connected to a 1522.
However, no device plugged into a 1522 can access a device plugged into the 3700's ethernet switch. Likewise, the devices plugged into the 3700 cannot access devices plugged into 1522s.
Devices plugged into the 3700's switch can access the internet and can access each other.
I have changed network cables, power cycled all devices (PCs, bridges, routers, etc) at least once. I am running latest firmware on 1522's and 3700. In short, I've tried just about all the basic stuff.
It almost appears that the 3700's switch is acting as an isolated network. I would say that were true, except that I can access the router admin page from anywhere (any 1522 and directly connected to the 3700).
All devices are within the 10.0.0.x address range with a subnet mask of 255.255.255.0. Again, I have no problems accessing the internet. Just the problem of devices plugged into a 1522 communicating with devices plugged into the 3700 and vice versa.
D-Link DAP-1522 :: Access Configuration Pages Via Wireless
Jan 9, 2012I have a DAP-1513 unit but there is no section for that unit on the forum.Is is possible to access the configuration pages over the wireless connection. After setting up access to the main router via WPS, I can access the configuration pages for a few minutes after I "power cycle" the unit.
View 9 Replies View RelatedD-Link DAP-1522 :: Can't Access Admin Screen After Connected
Nov 30, 2011I have a Netgear WNDR3300 Dual-Band and is setup to use both 2.4Ghz and 5Ghz to achieve 300 Mbps connection.
On the DAP-1522, I use IE (not Firefox or Chrome) for configuration as follow:
- IP address: STATIC
- Wireless config: using Wizard
- Wireless security: WPA2 / AES
- Mac Cloning: disabled
I tested this by connecting a Windows 7 desktop AND laptop via Ethernet cable and both laptop can obtain IP address dynamically, so my DAP-1522 is talking to the WNDR3300 (it has DHCP). Both Win 7 machines can also access the Internet.The problem is, I can NO LONGER access DAP-1522 admin screen, even by typing the static IP address assigned to it. The ONLY way I can re-access it is:
a). Reset DAP-1522
b). Shutdown the WNDR3300 wireless router, assign a static IP to the laptop, connect via cable to DAP-1522