D-Link DAP-1522 :: Can't Access Wired WNDR3700v2 Device

Dec 11, 2011

I have 4 DAP-1522's bridging to a WNDR3700v2.  Any device plugged into any of the 1522's can access the internet and can access shared drives etc. on any other device plugged into any 1522.  I can access the WNDR3700 admin website from a device connected to a 1522.

However, no device plugged into a 1522 can access a device plugged into the 3700's ethernet switch.  Likewise, the devices plugged into the 3700 cannot access devices plugged into 1522s. 

Devices plugged into the 3700's switch can access the internet and can access each other.

I have changed network cables, power cycled all devices (PCs, bridges, routers, etc) at least once.  I am running latest firmware on 1522's and 3700.  In short, I've tried just about all the basic stuff.

It almost appears that the 3700's switch is acting as an isolated network.  I would say that were true, except that I can access the router admin page from anywhere (any 1522 and directly connected to the 3700).

All devices are within the 10.0.0.x address range with a subnet mask of 255.255.255.0.  Again, I have no problems accessing the internet.  Just the problem of devices plugged into a 1522 communicating with devices plugged into the 3700 and vice versa.

View 2 Replies


ADVERTISEMENT

D-Link DAP-1522 :: WPA Not Working With Android Device?

Dec 4, 2011

I am unable to connect and Android device (HTC Desire, Samsung Nexus S etc) wirelessly to the DAP-1522. I've search through the forums and can't find anyone else having issues with Android so I think it must be one of my settings. It works fine if I switch to WEP however I don't want to use the weaker hackable protocol. Any way to have the DAP-1522 in WPA working with an android device?

View 4 Replies View Related

D-Link DAP-1522 :: Connect A Number Of Wired Devices In A Couple Of Different Rooms

Feb 11, 2011

I am currently using a DIR-655 for the home wireless network.DSL into a 2-Wire home portal (not wireless) and ethernet into the DIR-655.I need to connect a number of wired devices in a couple of different rooms. Some streaming HDTV content to other devices in other rooms. I'm thinking of the following:

-DIR-655 routing between the DSL subnet to the internet, the 2.4GHz wireless and a couple of wired devices.

-DAP-1522 routing between the 2.4GHz wireless, 5GHz wireless, and a few wired devices.

-DAP-1522 bridging between the 5GHz wireless and a few wired devices.

All devices will/may need internet access.HDTV content would be between wired devices and only over the 5GHz wireless (no HDTV to/from internet).Is the DAP-1522 the right device(s) for this?

View 2 Replies View Related

DAP-1522 / Adding Wireless Access Point To Wired Network?

Dec 27, 2010

Here's the setup:

DGL-4100 (wired gigabit router)
-> Wii
-> X360
-> PS3
-> DGS-2205 (wired gigabit switch in study)
*-> My PC
*-> Her PC
*-> DAP-1522 (wireless access point/bridge)

Now, we're on the 192.168.1.x domain, and I've already hooked my PC up directly to the DAP-1522 and switched its IP address. So now, I can connect to it through the switch. I've renamed it, set it to WPA2 with a passphrase, and should be set to go. However, I can't get my laptop, IPod touch, or any devices to see it. I tried entering the SSID manually, and nothing can find it.

View 2 Replies View Related

Getting An Access Point Hardwired To A WNDR3700v2?

Dec 9, 2012

What so you think as an access point hardwired to a WNDR3700v2?Buffalo WCR-GN AirStation N-Technology Wireless-N150 Router & Access Point - 150Mbps, RJ-45, 2412 - 2462 MHz, 4x LAN Ports, WAN, Wireless-N, WE

View 3 Replies View Related

D-Link DAP-1522 :: No Internet Access With It

Nov 29, 2010

I have a DIR-655 router with a DAP-1522 connected in bridge mode.  The firmware on the router is 1.21 and the firmware on the bridge is 1.21.  I have my SSID set to broadcast on the DIR-655 with WPA-Personal encryption.  When I initially setup the DAP-1522, I was able to access the setup page and connect to the DIR-655.  On the status page of the DAP-1522, wireless radio is enabled and status is connected.  I connected my XBOX 360, Sony BR player and DirecTV DVR to the wireless bridge and none of them can connect to the internet.

I can wirelessly access the bridge's IP, 192.168.0.50, from any computer connected to the DIR-655 but when I attempt to access the internet on any device connected to the DAP-1522, I do not get a connection.  On the XBOX 360 I cannot connect my live account.  On the Sony BR player, I get a message that new firmware was found, but when it attempts to connect to the internet to download it, the connection times out.  Same occurs when attempting to access the internet on the DirecTV DVR receiver.

View 14 Replies View Related

D-Link DAP-1522 :: Unable To Access It

May 25, 2012

More that a year ago, with guidance from D-Link Customer Service, I performed setup on a system consisting of a DSL-2640B (with wireless disabled) and a DAP-1522 as an access point. I included the 1522 so as to have an N network, since the 2640 is G. The system works fine and I'm able to stream via the 1522 to an N 300 USB Adapter. Internet access is fine, and I'm able to access the 2640 with no problem.I want to add another 300 in a different location. To do that, I'll need to access the 1522 from my Windows 7 computer, since I've lost the passphrase that I'll need for the 300.Everything that I've read tells me to connect the 1522 directly to my computer via cable and to temporarily change the network adapter settinge to:

IP = 192.168.0.x         various sources list values of 2 and 99 for x
Subnet mask = 255.255.255.0
Gateway = 192.168.0.50

Then to use a browser window to go to 192.168.0.50 Regardless of the settings that I use, the browser (IE9) always indicates that it can't connect with that address. accessing the 1522, or on any alternative way to obtain the passphrase.

View 3 Replies View Related

D-Link DAP-1522 :: No Internet Access With Connection To DIR-655

Aug 29, 2012

I have a DIR-655 set up as follows: [code] Lost Internet Access on my DAP-1522 on only my wireless laptop connection, but not other wireless nodes on the DAP-1522.I have most of my wireless nodes attached to the DIR-655, which is upstairs. Downstairs is where the DAP-1522 is located. There is a wired connection between the DIR-655 and DAP-1522. The DAP-1522 is being used as a Access Point. On this I have only three nodes that are wireless. My Smartphone, iPad and my laptop. There are also three nodes that are using the wired ports with no issue accessing the internet. The setup above have being working for over two years with no issue. Then three days ago my laptop connects to the DAP-1522, but has "No Internet Access." If I change my wireless connection to the DIR-655 on my laptop, then I do have internet connection. My Smartphone and iPad still are able to access the DAP-1522 and get the internet.

I have deleted my DHCP Reservation for only my laptop on the DIR-655. Wireless connection to the DAP-1522, looked at the DIR-655 and see that DHCP Reservation show the MAC of the laptop and I Reserve it. Still "No Internet Access." On the DAP-1522 it does show that my laptop is associated to this device. I cannot ping my local LAN IP Addresses , a website or Public IP Address only from the laptop. The DIR-655 shows a "Do Not Enter: Wireless system with MAC address 4025C2B97110 disconnected for reason: Received Deauthentication" with a connection to the DAP-1522, but shows "Do Not Enter: Wireless system with MAC address 4025C2B97110 secured and linked" with a connection to the DIR-655.

View 6 Replies View Related

D-Link DAP-1522 :: Access Configuration Pages Via Wireless

Jan 9, 2012

I have a DAP-1513 unit but there is no section for that unit on the forum.Is is possible to access the configuration pages over the wireless connection.  After setting up access to the main router via WPS, I can access the configuration pages for a few minutes after I "power cycle" the unit.

View 9 Replies View Related

D-Link DAP-1522 :: Can't Access Admin Screen After Connected

Nov 30, 2011

I have a Netgear WNDR3300 Dual-Band and is setup to use both 2.4Ghz and 5Ghz to achieve 300 Mbps connection.

On the DAP-1522, I use IE (not Firefox or Chrome) for configuration as follow:
- IP address: STATIC
- Wireless config: using Wizard
- Wireless security: WPA2 / AES
- Mac Cloning: disabled

I tested this by connecting a Windows 7 desktop AND laptop via Ethernet cable and both laptop can obtain IP address dynamically, so my DAP-1522 is talking to the WNDR3300 (it has DHCP). Both Win 7 machines can also access the Internet.The problem is, I can NO LONGER access DAP-1522 admin screen, even by typing the static IP address assigned to it. The ONLY way I can re-access it is:

a). Reset DAP-1522

b). Shutdown the WNDR3300 wireless router, assign a static IP to the laptop, connect via cable to DAP-1522

View 3 Replies View Related

D-Link DAP-1522 :: To Work As Wireless Access Point To DIR-825

Jun 4, 2011

So just recently purchased the DIR-825 and DAP-1522.  At this point I just want to get the DAP-1522 to work as a wireless access point to my DIR-825.  So my wireless laptop would connect wirelessly to the DAP-1522 and the 1522 would go wireless to the router.  Pretty basic I guess.  I was planning on using the WAP to strengthen the 5 GHz signal to the router but again, at this point, I would be happy to get the 2.4 GHz working.

I've been working on this since last night and got frustrated and went to bed.  I woke up fresh and decided to try again and I'm not having making any headway.

DIR-825 is connected to my DSL modem and has no problem accessing the internet.  I can connect to either 2.4 or 5.0 directly from my laptop with no problem at all and have access to the internet.  Encryption is disabled.  It worked with encryption but I turned it off to troubleshoot this AP problem.

It should be simple but I must be doing something wrong.  BTW is there a way to scan for network devices from the router or the access point?  I tried discovering each device with the wireless setup button on each device but they don't recognize each other so I'm configuring this manually.

So the DAP has access point enabled and 802.11 is running in mixed mode.  I've tried different variations but nothing has worked.  I've tried 20 mhz and 20-40 auto mhz channels but same problem.  Wireless security is off for troubleshooting at the moment.

DHCP server is disabled and I've assigned the DAP an available ip from the router's dhcp range.  I can connect to the DAP both wirelessly and hard wired.  The problem is that it can't seem to connect to the router.  So my laptop can connect to the router and ha internet access.  And it can also connect to the DAP but does not have internet access.  The ip is showing auto configuration 169.x.x.x when connected to the DAP so I'm not getting an ip.  Is the router supposed to assign the ip to my laptop through the DAP?  But again, if the DAP can't communicate with the router, then that would explain why I can't get an IP.

View 1 Replies View Related

D-Link DAP-1522 Wireless - Create Access Point Password?

Mar 3, 2013

i cant create dlink acess point password , if I am going 192.168.0.50 then showing error massages , I am check two three computer , then the same error coming

View 1 Replies View Related

D-link Dap-1522 :: Wifi Performances When Used As Access Point / Switch

Apr 2, 2013

I would like to use the DAP-1522 as an Access Point (wired to my router). My two concerns are:Can the 3 remaining ethernet ports be used to wirely connect to local PCs (so the DAP-1522 also acts as a switch) ? In case answer to the previous is yes, would it affect the performances of the wifi ?

View 3 Replies View Related

Linksys Wired Router :: BEFSR81 / Add Device Names To DHCP Device Table?

Nov 30, 2011

My BEFSR81 is my primary router and has DHCP turned on.  The router's DHCP range is set to accommodate 12 devices.  I have three computers wired to it and their Host names (as specified in the set-up of each computer) show up in the router's DHCP device table.  I also have two printers (one old Brother HL5250DN laser printer and one new HP Photosmart Premier C410a inkjet printer) connected and there are blanks where the Host name should go.  I would like to be able to tell which printer is which when I am looking at the DHCP device table.  How can I get a names associated with each printer's IP address in the router's DHCP device table?  (The real problem is that the router seems to have both printers at the same IP address (192.168.1.100) and if I can get one of them to change I'd like to know which one it was!)

View 1 Replies View Related

D-Link DIR-655 :: Controlling Device Access On Network

Feb 6, 2012

I have a new audio/video receiver that has Apple Airplay functionality built in.  Now the Airplay allows any Iphone/pod/pad/tunes device/computer on the same network to route music to the receiver without plugging in the device directly.  Great concept but the execution allows any computer or iphone in my house on the network to take over my receiver with no questions asked and start playing. 

So far I have failed to find a way to restrict or shut off Airplay on the device itself (other than disabling it's network).  If there is anyway through networking or my DIR-655 router to control/restrict this access?  What I would like in a perfect world is to keep all computers and wireless Apple I devices from connecting to the unit unless I allow it for that particular device/computer.  In an imperfect world I would accept just blocking wireless devices from it but still allowing them full network connectivity otherwise.Some things I have thought of - Can I use static addressing for the A/V receiver but put it on a different subnet then what my router is set to?  Is there some network control in the firewall that may limit access to the A/V receiver?

View 14 Replies View Related

Networking :: How To Setup 1:1 Nat With WNDR3700v2

May 31, 2011

I am about to get a group of 5 public (external) IP addresses from my ISP. I have a Netgear WNDR3700v2 router. I was told that 1:1 NAT would be the way to assign static public IP addresses to some of my computers, while making the rest use private network IP addresses (issued by a DHCP server), and have all the computers accessible in the same domain network.

Is this possible using my netgear WNDR3700v2 router? If not, what do I need?I was looking at the Netgear FVS318G wired router, and I would then use my existing router as an access point. Does this make sense?

View 1 Replies View Related

Setting Up Netgear WNDR3700v2 Router?

Jul 27, 2012

SETUP CD MISSING - NETGEAR WNDR3700v2Have just received excellent condition 'barely-used' WNDR3700v2 router with ac adaptor, but NO setup cd. Am I dead in the water, as Netgear doesn't provide replacement CD's, or is there a workaround using say, an early firmware upgrade? Or other?

View 2 Replies View Related

Laptop Can't Connect To (Netgear WNDR3700v2) Router

Dec 23, 2011

connecting my old laptop to my router (Netgear WNDR3700v2) The router is an N router but is backwards compatible, but my laptop can't find it. The laptop is an LG LE50-5273V. I looked into the device manager and found two network adapters; 802.11b/g wireless adapter and Marvell Yukon 88E8036 PCI-E Fast Ethernet Controller. So it should be able to connect to it? Besides from that laptop I have another PC connected to the router and it works (Using N), Will I then be able to combine both N with B/G?

View 2 Replies View Related

D-Link DAP-1522 Not Connecting

Mar 10, 2013

My D-Link DAP-1522 wireless bridge is connected through a single cat5 cable from the LAN port on my PC to the 1st LAN port on the D-link unit. At the moment, it is in bridge mode, with the blue power indicator on, the orange wireless connection light flashing, and the 1st LAN port connection periodically wavering indicating that it is communicating with my PC. When I attempt to configure the DAP-1522 via my internet browser, (IP 192.168.0.50) I get an error saying that the requested webpage does not exist.

View 6 Replies View Related

D-Link DAP-1522 - Unable To Log On After Network Changes

Sep 30, 2011

I recently had a networking guy set up a VPN for me, but for it to work properly he had to change all my IP addresses to 192.168.10.xx from 192.168.0.xx. My DAP-1522 (in bridge mode) continued to work but I am unable to log on to it, I think because it's address is 192.168.0.0. I have run into some other issues which makes me think I may need to upgrade the DAP-1522 firmware and/or assign it an address beginning with 192.168.10.xx, however I can't log on to the bridge. (Nor do I know how to change or possible reassign the DAP-1522's address through my router, a DIR-615).

View 5 Replies View Related

D-Link DAP-1522 :: Not Connecting To DIR-815 Properly?

Apr 26, 2011

My problem is two-fold:

1. the DAP-1522 will not connect to the 5GHz network of the DIR-815. Although, this doesn't surprise me as none of my 5GHz-capable devices see it, other than intermittently and at low signal. It is most likely an issue with the 815's 5GHz radio/network.

2. OTOH, the 1522 does appear to connect to the 815's 2.4GHz network just fine. However, there is no Internet access for any of the devices connected to the 1522's ports.

I know the 1522 can work correctly on 2.4GHz, as it previously did fine with my prior 2Wire router from AT&T. (I've just switched to Comcast, using the DIR-815 connected to their SMC modem.)

Also, I know the router and modem work fine (at least with 2.4GHz), as all of my wireless devices connect easily and with screaming bandwidth to the router and Internet.

View 4 Replies View Related

D-Link DAP-1522 :: Can't Bridge PC Or Printer

Mar 12, 2012

I have a WIN XP desktop which I successfully connected to the 1522 AP - as evidence of the GUI to program it.  I have the 1522 set to Bridge Mode via the switch on the unit.  The 1522 has hardware version B1 and Firmware version 2.000.  I joined my wireless network successfully as evidence of the Status page showing it's successfully connected and bridged to my network.  I then disabled my USB wifi NIC in hopes of using my hardwired connection to the 1522 to get on the internet.

Wireless Radio : Enabled
Bridge State : Connected
MAC Address : fc:75:xxxxxx
802.11 Mode : Mixed 802.11a, 802.11g and 802.11n
Band Width : 40
Channel : 6
Network Name
(SSID) : cleveland
Wi-Fi Protected Setup : Enabled
Security : WPA2-PSK

View 3 Replies View Related

D-Link DAP-1522 :: Can't Update Firmware To 1.31

Dec 7, 2011

I have dap-1522 version A Browser IE8 with lestest updates.

I downloaded the DAP1522_FW_1.31zip went I try to upload via the 1522 admin error not correct file.

I try three different way to download it, could the file be bad on dlinks web site?

View 4 Replies View Related

D-Link DAP-1522 :: Incompatible With Almost All New Pioneer AVR's?

Aug 27, 2010

I have just discovered after three weeks of testing that DAP-1522 wireless bridges are not compatible with all the new Pioneer AVR's that support internet radio and Iphone control.  Anytime a DAP-1522 is powered on and on the same subnet mask as a Pioneer receiver it will cause the Pioneer to loose it's connection every 30 minutes.  The receiver is then not able to connect unless it is powered off and on again. The DAP-1522 will cause this even if the Pioneer is hardwired to a router and nothing is plugged into the DAP-1522.  This affects all new models of Pioneer receivers including the Elite line like I have.

I have tested this with 3 differnet Pioneer receivers and 2 DAP-1522's and always got the same results no matter what the settings were and with the 1522 in AP or bridge mode.  Other Pioneer receiver owners experiencing constant disconnect problems on another forum have now also confirmed they have DAP-1522's.....and they are also pissed after spending countless hours troubleshooting.

I talked to Dlink support today and they will not admit to a problem so I can't wait to contact Pioneer tech support on Monday to let them know I have found the reason they are seeing returns on their new receivers (some cost as much as $7K) since many of the new owners like myself are exchanging them thinking they got a bad one.  I'm sure Pioneer will test this immediately and force a Dlink fix or turn it over to the FCC.At this point I just wish I could get my money back since I have also already confirmed that a netgear bridge works just fine.  Come to think of it, I know Dlink has a new refund policy, but I will check with my state district attorney to see if they can legally keep my money even if the product doesn't work. I don't see anything on the outside of the box with this policy so therfore I wasn't given fair warning of the policy before purchase and would not be expected to know it since it is not industry standard.  Let the games begin.

View 14 Replies View Related

D-Link DAP-1522 :: Won't Accept New Firmware

Mar 14, 2012

I just purchased a DAP-1522. The sticker on the bottom says it's a version B1, with firmware 2.0.In the web interface, it says: "Firmware Version :   1.21 , Fri 26 Jun 2009"I downloaded the 2.01 firmware from the D-Link site and when I try to upload it, it says it's not an image file.

View 11 Replies View Related

D-Link DAP-1522 :: How To Get Ip From Dwl 2100Ap Not By Livebox

Jan 20, 2011

I have bought 1 Dlink Dwl 2100 Access Point about 1 week, it working with ( Default Gateaway 192.168.1.1) but I want connect with 2100Ap But I get Ip from my Livebox Orange.Can I get Ip From 2100Ap (Default Gateway 192.168.0.50), not by LiveBox Orange (Default Gateway 192.168.1.1).My brother live upstair (with LiveBox) I  Live ground Floor and connect to Cable Utp cat5 form upstair to ground Floor. In my room I have a Switch connect to 2100Ap.

LiveBox Orange Default gateway is 192.168.1.1
Dlink dwL 2100Ap Default Gateway is 192.168.0.50
My os is windows Xp sp2

View 2 Replies View Related

D-Link DAP-1522 :: DIR 655 Quit Working

Feb 14, 2012

My DIR 655 router quit working and so I called D link.  She had me reset the ip to 192.168.5.x.  So now my dap1522 is not connecting to the 655.  I connected the dap1522 to my laptop via ether-net and typed in dink, and got nothing, then put in default ip for the 1522 and still nothing. I also tried ip scanner and it would not come up.

View 1 Replies View Related

D-Link DAP-1522 :: Administration Web Of Switch Is Not Available

Jan 10, 2012

my config : one DAP-1522 as an AP + one DAP-1522 as a switch, 6 meters between them, signal strength about 70. Any others wifi networks around my house. both with FW140b03.bin dated 01/14/2011.Most of the time, both work correctly. But time to time, the wifi link is ko. In AP status, the switch is mentionned connected (uptime = 3 hours ...). The red led is blinking on the switch. The administration web of the switch is not available and the link is ko. Unplug and plug power units doesn't fix the problem. I need to reset DAPs.From Dlink experts, i would like to get more description about issues :

- in switch mode, which are the events modifying the red led state ? what does blinking / off led mean ?

- in AP mode, what does "uptime ...STA ...." mean ? frames are periodically received from STA ?

View 7 Replies View Related

D-Link DAP-1522 :: Comparability With 3D Material?

Aug 8, 2011

Will the dap-1522 work with 3d video ie; from a 3d Blue Ray Player? I am upgrading system to an LED Samsung 3D TV and Samsung 3d Blue Ray Player. I know that HDMI 1.4 cables will work but am looking at the wireless option.

View 1 Replies View Related

D-Link DAP-1522 :: Unable To Login With Default IP?

Jan 5, 2012

 changed the router wan access pwd and now trying to test the dap i can't seem to log in with the default ip / dlinkap url access i have tried the bridge and ap switch setting on the dap with no luck after resetting the dap a couple of times with no luck ..

View 8 Replies View Related

D-Link DAP-1522 :: How To Enable 5Ghz Band

Oct 13, 2011

I installed my 1522 today with a Direct TV receiver and made a connection using AP mode.

How do I know what band is being used and how to switch between the bads.

View 1 Replies View Related

D-Link DAP-1522 :: DNS Server Not Shown In Static IP

Mar 16, 2012

Under Advanced>DHCP Server, when I put in the Default DNS server of 192.168.0.1 and click save, it goes away. Meaning it doesn't show up anymore.

View 4 Replies View Related

D-Link DAP-1522 :: Do Devices Talk Directly

Apr 14, 2013

Do the devices connected to the DAP-1522 communicate directly with each other or do they communicate through the router.My DAP-1522 is set up as a bridge connected to my DIR-825.  The reason I ask is I've set up an HTPC connected to the DAP-1522 and I also have media devices connected to the DAP and am wondering if they'll communicate with each other directly or if they have do it by going to the router and back.  That way I can use my HTPC to serve media to my devices at local speeds.

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved