D-Link DAP-1522 :: Connect A Number Of Wired Devices In A Couple Of Different Rooms
Feb 11, 2011
I am currently using a DIR-655 for the home wireless network.DSL into a 2-Wire home portal (not wireless) and ethernet into the DIR-655.I need to connect a number of wired devices in a couple of different rooms. Some streaming HDTV content to other devices in other rooms. I'm thinking of the following:
-DIR-655 routing between the DSL subnet to the internet, the 2.4GHz wireless and a couple of wired devices.
-DAP-1522 routing between the 2.4GHz wireless, 5GHz wireless, and a few wired devices.
-DAP-1522 bridging between the 5GHz wireless and a few wired devices.
All devices will/may need internet access.HDTV content would be between wired devices and only over the 5GHz wireless (no HDTV to/from internet).Is the DAP-1522 the right device(s) for this?
View 2 Replies
ADVERTISEMENT
Apr 14, 2013
Do the devices connected to the DAP-1522 communicate directly with each other or do they communicate through the router.My DAP-1522 is set up as a bridge connected to my DIR-825. The reason I ask is I've set up an HTPC connected to the DAP-1522 and I also have media devices connected to the DAP and am wondering if they'll communicate with each other directly or if they have do it by going to the router and back. That way I can use my HTPC to serve media to my devices at local speeds.
View 1 Replies
View Related
May 17, 2011
This is the configuration I am running:Internet > Cable Modem > Netgear WNDR3700 Router ~~ DAP-1522 > Wired Windows 7 PC + Linux PC + Printer.The Windows 7 and Linus PC's do communicate well to the internet as do any laptops accessing the router wirelessly and any devices wired to the router. That is the good news.
The bad news is that any devices located after the DAP-1522, including the DAP-1522 do not show up on the network map of either the router or any of the wireless laptops. Neither does the Win 7 PC connected through the DAP-1522 show any networked devices, whether through the DAP-1522 or not, even though network discovery is turned on.
Right now the DAP-1522 is set up to function as a bridge and is in "Static IP" mode. I tried changing it to DHCP, but the DAP-1522 will not allow saving that setting, even though it will allow changing it. It just reverts back to "Static IP". The firmware version is 1.31, and the firmware update went well after a workable logon to the admin page was discovered. Also the one-button (WPS) set-up to the router worked as far as allowing an internet connection.
What needs to change to allow all the devices to show up on the network maps and maintain internet access? Ultimately, I would like to stabilize the IP's of the major components of the network to make troubleshooting easier. But to do that the devices need to show up on the network maps, particularly of the router, so they can be added to the IP reservation table by selection.
View 2 Replies
View Related
Dec 11, 2011
I have 4 DAP-1522's bridging to a WNDR3700v2. Any device plugged into any of the 1522's can access the internet and can access shared drives etc. on any other device plugged into any 1522. I can access the WNDR3700 admin website from a device connected to a 1522.
However, no device plugged into a 1522 can access a device plugged into the 3700's ethernet switch. Likewise, the devices plugged into the 3700 cannot access devices plugged into 1522s.
Devices plugged into the 3700's switch can access the internet and can access each other.
I have changed network cables, power cycled all devices (PCs, bridges, routers, etc) at least once. I am running latest firmware on 1522's and 3700. In short, I've tried just about all the basic stuff.
It almost appears that the 3700's switch is acting as an isolated network. I would say that were true, except that I can access the router admin page from anywhere (any 1522 and directly connected to the 3700).
All devices are within the 10.0.0.x address range with a subnet mask of 255.255.255.0. Again, I have no problems accessing the internet. Just the problem of devices plugged into a 1522 communicating with devices plugged into the 3700 and vice versa.
View 2 Replies
View Related
Jul 15, 2012
Just upgraded my system. I am using D-Link 615 as access point hardwired LAN to LAN to ActiveTec MI424WR N capable Verizon Fios Wireless Modem/Router. The Fios Router is set up with WPA2 security. Intend on having three 615s as Access Points off of ActiveTec. Have a number of wireless devices accessing the network. Have followed instructions from manual to use 615 as Access Point, disabling UPnP and the DNCP Server function on the 615. My ActiveTec IP address is 192.168.1.1 and I changed the 615 to 192.168.1.50. I can type this IP address in my browser and get to the 615 set-up.
I have tried a couple different options in naming the SSID on the 615 set-up. If I name the SSID on the 615 the same as the ActiveTec router, when I go to Connect to a wireless signal where there is overlap, there are two signals that one can connect to, named the same SSID, the Fios is WPA2 secured and the 615 is not. Shouldn't these all be on one SSID? It seems that I have two different networks (different SSIDs) instead of one (rather than the 615 simply serving as an extension of the Fios router as a wired remote access point) with different security protocols (WPA2 and None). The SSID name almost seems meaningless. If I name the 615 SSID the same as the Fios router SSID or something different, I still have the option of selecting one SSID that is secure and one that isn't. If I try to connect to the SSID name associated with the 615 I can get on without providing a password.How do I make it so that one can walk around and go from one area to the next and seamlessly move to the best signal? I did read to select different sets of channels for each access point.
View 3 Replies
View Related
Jul 27, 2012
I recently noticed my 'Number of Dynamic DHCP Clients' on Network Settings is always empty. Before, it always registered a list since there are several devices that are connected to our wireless network (laptops, mobile phones, desktops).
View 3 Replies
View Related
Oct 11, 2012
All of a sudden my laptop, android phone and blu ray player (all wireless devices) can't communicate with my wired devices (marantz receiver and samsung tv). Everything still connects to the internet independently but i can't for instance play music from my wireless laptop to my wired marantz receiver. I had no trouble with this last week and didn't change anything (that I'm aware of) I did get Verizon to switch out my router but it didn't solve anything. My wife's computer also cannot connect to wired devices. Lastly, if I connect my laptop with via ethernet cable it sees wired devices fine. I tried shutting off windows firewall but didn't work. I have no other firewall/virus software installed. I can ping to all devices (wired and wireless) from my laptop.
View 1 Replies
View Related
Nov 6, 2011
I recently bought a new D-Link DIR 615 but I dont get adequate range in the rooms farthest away from the router. I have an old D-Link DIR 634M router which I'm told can be used as a wireless repeater.I went through several articles that describe connecting the two routers through a LAN cable. However is there a way to do the same without using a cable of any sorts?
View 1 Replies
View Related
Oct 24, 2011
I am new to these forums and I have upgraded from firmware 1.00 on the DIR-815 to the 1.01 firmware and once I upgraded, I can log into Xbox, but can't host party chats or host game rooms. I also noticed that any and all messages sent from friends didnt show until I rebooted my console. Something is SERIOUSLY WRONG here and would like a MOD to comment on this.
View 12 Replies
View Related
Jul 31, 2012
After a firmware update the DAP-1522 HWversion A will not connect to a Hide SSID.
I am Using the DAP-1522 as a Bridge in 5Gz.
View 6 Replies
View Related
Jan 5, 2013
Just bought a dir-655, set it up (all though the wizard wasn't working, it kept getting stuck on step 5 of 7) so I just configured everything manually.I'm getting 2.4 MB/s speeds wirelessly.I was expecting much better, my wireless g linksys router did just slightly lower than that. My xbox 360 can't even stream HD without buffering every few mins. It also will just stop, and be unable to see the media for a couple minutes (when doing HD).I have wireless setup as WPA2, and the devices I use wirelessly are N devices. I have the router setup to only use wireless N.
View 14 Replies
View Related
Jan 14, 2013
Is it possible to connect the dap-1622 to a hidden network using WPA Radius? I've tried, but didn't succeed. I'm running FW version 1.41. I've tried with older FW versions, and none of them seems to work.
View 1 Replies
View Related
Jan 25, 2011
Can't connect DAP-1522 to my Verizon Fios Router
Went through the setup on the DAP-1522. Selected my Verizon FIOS wireless network and entered the WEP key. Everything looks ok on the status page - except Status: Disconnected
Reset/restarted and reconfigured DAP-1522 several times - same result. Can't get it to connect.
View 1 Replies
View Related
Feb 24, 2011
Ive had this 655 for about a year now and it has been rock solid. But, there has been one slight issue.
And and all wireless devices can see each other and all wired devices can see each other....but the wired cant see the wireless and vis versa.
The wireless devices (W7 and Vista laptops) can see the wired devices when they are plugged in. But my phone and Galaxy Tab can only see whatever wireless devices there are (cant be plugged in). Even my wired Samsung TV cant see the shares on the Tab or wireless laptops (and vis versa). So, its certainly not a firewall or OS config issue.
Now, I made sure they are all connecting via the main SSID and not the "isolated" Guest SSID....but its acting like the main SSID is isolated from the wired LAN somehow.
Firmware 1.34. IPs for the wired and wireless devices are all in the 1.2 - 1.50 range.
View 14 Replies
View Related
Mar 1, 2013
I currently have an old Linksys WRT54G router with 4 ethernet and 1 internet port. I have an old Sprint 660 modem connected to the router for internet access. I am also using 3 of the 4 ethernet ports for wired devices (main PC, NAS drive and Dish Network net access). I have another PC and a printer connected wirelessly to the router.Now, with my modem going bad, CenturyLink has provided a combo modem/router (EQ660DR-F1) to be used in place of my Linksys router/modem, providing wired, wireless and modem capabilities in one.My problem is that the new router/modem has only one ethernet port along with a DSL port. Obviously, I can connect my main PC to the ethernet port, DSL to the modem port and connect my 2nd PC and printer wirelessly as they are now. How I might connect my other 2 wired devices, possibly by a hub, AP or bridge or some other means? Can one of these be connected by wireless to connect the other 2 devices, or do these have to be connected physically by wire?
View 2 Replies
View Related
Dec 27, 2010
Here's the setup:
DGL-4100 (wired gigabit router)
-> Wii
-> X360
-> PS3
-> DGS-2205 (wired gigabit switch in study)
*-> My PC
*-> Her PC
*-> DAP-1522 (wireless access point/bridge)
Now, we're on the 192.168.1.x domain, and I've already hooked my PC up directly to the DAP-1522 and switched its IP address. So now, I can connect to it through the switch. I've renamed it, set it to WPA2 with a passphrase, and should be set to go. However, I can't get my laptop, IPod touch, or any devices to see it. I tried entering the SSID manually, and nothing can find it.
View 2 Replies
View Related
Mar 1, 2013
In my device I am able to browse through & connect to my HOME wifi network ; But after connecting it says 'No Internet Access'.I tried connecting with my SONY Bluray , iphone , ipad , laptops -- everywhere same story.I am able to plug in the ethernet cable directly from modem & able to connect to network.I am not able to open the http://192.168.0.1 -- ( When I am plugged in the modem directly)
Following are my router details
FCCID - KA2DIR601A1
IC : 4216A-IR601
H/W Ver:A1
F.W Ver:1.00 NA
View 12 Replies
View Related
Jul 11, 2011
i have had a DIR-655 Rev. A router for years now and had no problems connecting my laptop to it well over 150m, the iproducts never got over 65m, i'm OK with that if they just won't but i would like to get there if possible. i went out and picked up a 2nd 655 (rev B) and flashed the bios up to the newest version 2.03NA and went in and mirrored all of the settings from the original router and then replaced the old router with the new one. the old router is not being used at this time though there are plans to use it as an access point later in another part of the house. i have updated the drivers for the wireless N card on my laptop (i can't remember the name of the adapter or the model, i'll provide that when i go home for lunch today). i've tried various settings for security, (i want to use WPA2 only, personal key, AES cipher, channel width 20/40 auto) i've even tried no security and it still won't connect over 65m.
View 14 Replies
View Related
Apr 5, 2012
We can only connect 2 devices at a time. Someone suggested that it may be a setting with my wireless router.
View 2 Replies
View Related
Feb 3, 2013
I have just switched to a new internet provider (UnityMedia in Germany) and they provided me with a CISCO cable modem (EPC3208G) and a 'wireless N 150 Home Router DIR-600' (hardware Bx and firmware 2.13). I had to ring the service desk to complete set up. I was told to connect the LAN cable (from the modem) into LAN number 1 rather than 'internet' (in the router). I was also told to change the router IP address to 192.168.0.2. Thereafter the connection to the internet was established (they also asked me to make some other changes which I can no longer recall). However after the phone call with the D-link service desk I attempted to connect my other internet enabled devices (kindle, internet radio and smartphone) and apart from one other laptop nothing can connect to the internet.
View 5 Replies
View Related
Mar 21, 2012
I am currently having issues with the dhcp function on my DIR-615. The issue is some of my devices are never able to connect unless I set them up with static ip. Some of my devices are sometimes able to connect using DHCP but sometimes need to be set up with a static IP. In the log it says something along the lines of "sent out offer for IP 192.168.0.XXX" but the devices never receives the IP. The firmware says it is up to date. The hardware version is C1. Some of the devices having issues are PC's some are Macbooks and some are iphone and ipods. I'm not sure if it is related but when I look at who is using WAN some of the pc's who are connected to the internet have an ip address of 0.0.0.0.
View 3 Replies
View Related
Dec 4, 2012
I have a Linsys E3200 router for almost a year. It's been working fine until recently. It kept losing internet connection every a couple hours or even shorter. I have to power cycle the router in order to make it to work. However, sometimes that won't work either. I also tried to restore the router to the factory default but that doesn't seem to work.
I have updated the router with the latest firmware (1.04). I am using a cable connection and it never gives me any problem if I just connect my computer to it. I also test my network with another old netgear router that works just fine.
View 9 Replies
View Related
Dec 25, 2012
Am I limited to how many devices can connect to my wireless router 802.11g
View 2 Replies
View Related
Feb 15, 2013
I have a D-Link DIR-652 router, and I can see that it is broadcasting but I cannot connect through my laptop, tablet, or phone. Sometimes it will let me connect but other times it says it is unable to. I can connect when I plug into the router through a cable. I'm doing that now, and I did an ipconfig/all in case to see that:
Windows IP Configuration
Host Name . . . . . . . . . . . . : Kyle-PC
Primary Dns Suffix . . . . . . . :
[Code].....
View 10 Replies
View Related
May 12, 2013
For some reason, handheld devices cannot connect to our wireless dlink router. However, our HP laptop has no issue with connecting. Regardless of the make and model, no one else can connect at our home.
View 5 Replies
View Related
Nov 1, 2012
i've just a D-Link DIR-600 router last month and i successfully installed it and its working great. Until 2 to days ago, my brother told me that he can't conlnect to the wi-fi. I said that its working just fine and told him to just reset his phone. And then, my sister also told me that she can't connect too. I checked their devices like iPhone 4S and iTouch and it says "Unable to join the network....... Also phones of my friends can't connect also. It was just working fine. I haven't changed anything on the router's configuration. I already reset the router, unplug then plug it and its still not working. The router is connected to my laptop and I can still browse the internet. Its the wireless connection that is not.
View 5 Replies
View Related
Jul 31, 2012
DIR-615 REv E, Originally had a Windows vista, windows 7, sony bravia tv (hardwired), sony blue ray player, 2 blackberry torch, an ipod, and whoever else happened to be there connected. After a router push button reset 7 reconfigure, only the windows vista and a samsung tablet will connect. The windows 7 computer sees the router but cannot see the internet. It does connect if hardwired thru the router.
View 1 Replies
View Related
Mar 1, 2013
I have the firmware 2.10NA. In my home we have about 4 laptops and 4 smartphones connecting to this router wirelessly and 3 of the laptops often lose connection for hours. We have tried unplugging the router and plugging it in again and factory reset and also resetting it through the IP address but the connection doesnt come back. Recently it has gone out for about 3 hours now. Also the wireless LED icon on the router constantly blinks is this normal? On the laptops where theres no connection it says limited connectivity. Is it possible that there is too many devices connected to the router or something. or could this be a problem with the laptops and not the router?
View 6 Replies
View Related
Nov 29, 2012
Region : UnitedStates
Model : TD-W8961ND
Hardware Version : V2
Firmware Version :
ISP : ATT
I want to add more users to my home network and I couldn't, at this moment I only can connect 8 devices (12 devices at least) when I try to connect the next one its impossible, but if I take off one of the connected devices then the router allows to connect the new one.How can I connect more than 8 devices to my router ? (wireless)Also, is there any limits with Wireless MAC Address Filter ? because I can't add more than 8 MAC addresses in my old router I could do that.
View 4 Replies
View Related
Mar 1, 2012
Cannot get DirecTV HD-DVR to connect to DIR-655 wired. Any way to get Direct TV to connect?
View 1 Replies
View Related
Jul 10, 2011
which is the maximum number of simultaneous wired guest clients on a 5508? And in a 2112 controller?
Wired clients count as wireless clients??
What about anchoring limitations, what is the effect of wired guest clients on the anchor controller?
View 2 Replies
View Related
Mar 10, 2013
My D-Link DAP-1522 wireless bridge is connected through a single cat5 cable from the LAN port on my PC to the 1st LAN port on the D-link unit. At the moment, it is in bridge mode, with the blue power indicator on, the orange wireless connection light flashing, and the 1st LAN port connection periodically wavering indicating that it is communicating with my PC. When I attempt to configure the DAP-1522 via my internet browser, (IP 192.168.0.50) I get an error saying that the requested webpage does not exist.
View 6 Replies
View Related
Aug 12, 2012
I've been using D-Link DIR-600 wireless router for two months with my ISP, SmartBro. A week ago my internet went down due to heavy rain and technical support had a home visit yesterday to re-activate my internet connection. My net connection came back smoothly using a direct connection from modem to laptop.When I tried to connect the modem to my wifi router, the internet was not detected. Even if I reset the router settings, no internet connection was detected. Initially, I thought there is a problem with my wifi router so I connected the modem to our Edimax wired router but still it could not detect internet access. Every time I open a browser while connected to a router, this message is shown (see attached screenshot).
I tried using another ISP, Wi-Tribe with both wired and wifi routers and everything worked well. So now I assume the problem lies with my SmartBro ISP. I called the ISP hotline but they told me that they do not provide support for router connection problems; only with single, direct connect to a PC.I asked a neighbor IT technician to look into my problem but he too could not solve the problem.
View 14 Replies
View Related
