D-Link DAP-1522 :: Do Devices Talk Directly

Apr 14, 2013

Do the devices connected to the DAP-1522 communicate directly with each other or do they communicate through the router.My DAP-1522 is set up as a bridge connected to my DIR-825.  The reason I ask is I've set up an HTPC connected to the DAP-1522 and I also have media devices connected to the DAP and am wondering if they'll communicate with each other directly or if they have do it by going to the router and back.  That way I can use my HTPC to serve media to my devices at local speeds.

View 1 Replies


ADVERTISEMENT

D-Link DAP-1522 :: Devices Local Do Not Show On Network Map

May 17, 2011

This is the configuration I am running:Internet > Cable Modem > Netgear WNDR3700 Router ~~ DAP-1522 > Wired Windows 7 PC + Linux PC + Printer.The Windows 7 and Linus PC's do communicate well to the internet as do any laptops accessing the router wirelessly and any devices wired to the router. That is the good news.

The bad news is that any devices located after the DAP-1522, including the DAP-1522 do not show up on the network map of either the router or any of the wireless laptops. Neither does the Win 7 PC connected through the DAP-1522 show any networked devices, whether through the DAP-1522 or not, even though network discovery is turned on.

Right now the DAP-1522 is set up to function as a bridge and is in "Static IP" mode. I tried changing it to DHCP, but the DAP-1522 will not allow saving that setting, even though it will allow changing it. It just reverts back to "Static IP". The firmware version is 1.31, and the firmware update went well after a workable logon to the admin page was discovered. Also the one-button (WPS) set-up to the router worked as far as allowing an internet connection.

What needs to change to allow all the devices to show up on the network maps and maintain internet access? Ultimately, I would like to stabilize the IP's of the major components of the network to make troubleshooting easier. But to do that the devices need to show up on the network maps, particularly of the router, so they can be added to the IP reservation table by selection.

View 2 Replies View Related

D-Link DAP-1522 :: Connect A Number Of Wired Devices In A Couple Of Different Rooms

Feb 11, 2011

I am currently using a DIR-655 for the home wireless network.DSL into a 2-Wire home portal (not wireless) and ethernet into the DIR-655.I need to connect a number of wired devices in a couple of different rooms. Some streaming HDTV content to other devices in other rooms. I'm thinking of the following:

-DIR-655 routing between the DSL subnet to the internet, the 2.4GHz wireless and a couple of wired devices.

-DAP-1522 routing between the 2.4GHz wireless, 5GHz wireless, and a few wired devices.

-DAP-1522 bridging between the 5GHz wireless and a few wired devices.

All devices will/may need internet access.HDTV content would be between wired devices and only over the 5GHz wireless (no HDTV to/from internet).Is the DAP-1522 the right device(s) for this?

View 2 Replies View Related

Cisco :: Access Directly LAP 1522 Using Console Port?

Sep 4, 2012

but is there anyway to access directly a LAP 1522 using a console port?

View 5 Replies View Related

Talk Talk Router - Connection Is Suffering Idle Timeouts Daily

May 21, 2012

I've got an aol engineer visiting Thurs.to examine connection loss (since last Weds). But I'm convinced the problem is with the router. But from the tone of the aol tech questions I suspect he's already briefed his engineer to do his best to represent the problem as being either with my computer or positioning of router/filters/condition of wall-sockets - usual getouts.The talktalk router is neww, issued Feb 12, after my original router, speedtouch, started suffering idle timeouts every day.

View 3 Replies View Related

Atheros AR5007EG TO Talk Talk Echolife Hg520b Router

Feb 20, 2011

I can connect to this router via Lan and have no problems.Via Wi Fi it connects but will not communicate with the router or see find the router vias ip address..I have turned on auto ip finding in network settings for Lan and for Wireless but wi fi still does not allow access to internet. It just says local only.when i go to Command prompt and do ipconfig /all it says all DHCP enabled are off!!

View 1 Replies View Related

Cisco WAN :: 2800 Can't Ping Directly Connected Devices

Mar 28, 2013

I'm trying to configure a 2800 series router. .I'm consoled in and put a basic config on the router (see attached). After putting this basic config on, I plugged it into a small unmanaged switch, changed my laptop's IP and plugged it in the switch also. I can't ping the router from the laptop and vice versa. This is the second switch I've tried this with, so it must be.The first switch, I installed at location, connected a cisco cable to it and a local server, so i could remote in and finish configuration. In that scenario, I had plugged the switch into a managed switch and had the same result as I'm getting now--can't ping IP addresses (can't ping the switch's IP, not can it ping local IPs).

View 2 Replies View Related

Cisco WAN :: 4500 Not Pinging Directly Connected Devices

Nov 3, 2012

We had a problem where a 4500 would not ping directly connected devices dispite being able to telnet to them and also view them in CDP. It was mostly forwarding packets between devices but some hosts could not connect to others.

View 1 Replies View Related

Cannot Connect To MSi Talk Talk Router

Dec 21, 2011

i am having trouble connecting my msi laptop to my talktalk to router i have another laptop that i cant really use however i turned it on to c if i can connect it to internet and i can but can not not matter what i do connect this one.

View 4 Replies View Related

Linksys Wireless Router :: E3000 Can Determine What Devices Are Connecting Directly To Router

Aug 15, 2011

I I use a Linksys E3000 router.  Sometimes when I look at the network map I see a device called "Unknown."  It appears as though the two notebooks sometime are going through this device to access the Linksys E3000.  (I've checked when both notebooks are on and I can determine what devices are connecting directly to the router and what devices are going through this unknown device.)  Is there any way to determine what this unknown device is?

View 5 Replies View Related

D-Link DIR-655 :: How To Connect Internet Lan IP Directly

Dec 11, 2012

We have a DIR 655 router that I have set up with LAN and WiFi, all good.Today we received our mast and antenna from Vodacom (ISP) with the Public IP's to enter into the router. We connected the LAN cable into the Internet Port and did a manual Internet Static IP setup.  But as soon as we click save it says:  Type is not for 3G...  How do I go about entering the public (static) IP's we received from the ISP in order to get the Internet operational?

View 8 Replies View Related

D-Link DAP-1522 Not Connecting

Mar 10, 2013

My D-Link DAP-1522 wireless bridge is connected through a single cat5 cable from the LAN port on my PC to the 1st LAN port on the D-link unit. At the moment, it is in bridge mode, with the blue power indicator on, the orange wireless connection light flashing, and the 1st LAN port connection periodically wavering indicating that it is communicating with my PC. When I attempt to configure the DAP-1522 via my internet browser, (IP 192.168.0.50) I get an error saying that the requested webpage does not exist.

View 6 Replies View Related

D-Link DIR-825 :: Disconnections - Wired Directly To Router

Jul 18, 2011

I have had my DIR-825 for a year and half. My computer that is wired directly to the router keeps losing the connection to the router - unable to obtain an address.  All of my other devices (that are connected via wireless) still hold the connection with no issues.  I've checked the cable, unplugged/plugged back into the router, and it shows connection on the network card on the back of the computer.I have used the system interface to ensure the address is a valid one.  I have powered up and down the computer multiple times and have also powered down and up both the router and the cable modem.

View 1 Replies View Related

D-Link DAP-1522 - Unable To Log On After Network Changes

Sep 30, 2011

I recently had a networking guy set up a VPN for me, but for it to work properly he had to change all my IP addresses to 192.168.10.xx from 192.168.0.xx. My DAP-1522 (in bridge mode) continued to work but I am unable to log on to it, I think because it's address is 192.168.0.0. I have run into some other issues which makes me think I may need to upgrade the DAP-1522 firmware and/or assign it an address beginning with 192.168.10.xx, however I can't log on to the bridge. (Nor do I know how to change or possible reassign the DAP-1522's address through my router, a DIR-615).

View 5 Replies View Related

D-Link DAP-1522 :: Not Connecting To DIR-815 Properly?

Apr 26, 2011

My problem is two-fold:

1. the DAP-1522 will not connect to the 5GHz network of the DIR-815. Although, this doesn't surprise me as none of my 5GHz-capable devices see it, other than intermittently and at low signal. It is most likely an issue with the 815's 5GHz radio/network.

2. OTOH, the 1522 does appear to connect to the 815's 2.4GHz network just fine. However, there is no Internet access for any of the devices connected to the 1522's ports.

I know the 1522 can work correctly on 2.4GHz, as it previously did fine with my prior 2Wire router from AT&T. (I've just switched to Comcast, using the DIR-815 connected to their SMC modem.)

Also, I know the router and modem work fine (at least with 2.4GHz), as all of my wireless devices connect easily and with screaming bandwidth to the router and Internet.

View 4 Replies View Related

D-Link DAP-1522 :: Can't Bridge PC Or Printer

Mar 12, 2012

I have a WIN XP desktop which I successfully connected to the 1522 AP - as evidence of the GUI to program it.  I have the 1522 set to Bridge Mode via the switch on the unit.  The 1522 has hardware version B1 and Firmware version 2.000.  I joined my wireless network successfully as evidence of the Status page showing it's successfully connected and bridged to my network.  I then disabled my USB wifi NIC in hopes of using my hardwired connection to the 1522 to get on the internet.

Wireless Radio : Enabled
Bridge State : Connected
MAC Address : fc:75:xxxxxx
802.11 Mode : Mixed 802.11a, 802.11g and 802.11n
Band Width : 40
Channel : 6
Network Name
(SSID) : cleveland
Wi-Fi Protected Setup : Enabled
Security : WPA2-PSK

View 3 Replies View Related

D-Link DAP-1522 :: Can't Update Firmware To 1.31

Dec 7, 2011

I have dap-1522 version A Browser IE8 with lestest updates.

I downloaded the DAP1522_FW_1.31zip went I try to upload via the 1522 admin error not correct file.

I try three different way to download it, could the file be bad on dlinks web site?

View 4 Replies View Related

D-Link DAP-1522 :: Incompatible With Almost All New Pioneer AVR's?

Aug 27, 2010

I have just discovered after three weeks of testing that DAP-1522 wireless bridges are not compatible with all the new Pioneer AVR's that support internet radio and Iphone control.  Anytime a DAP-1522 is powered on and on the same subnet mask as a Pioneer receiver it will cause the Pioneer to loose it's connection every 30 minutes.  The receiver is then not able to connect unless it is powered off and on again. The DAP-1522 will cause this even if the Pioneer is hardwired to a router and nothing is plugged into the DAP-1522.  This affects all new models of Pioneer receivers including the Elite line like I have.

I have tested this with 3 differnet Pioneer receivers and 2 DAP-1522's and always got the same results no matter what the settings were and with the 1522 in AP or bridge mode.  Other Pioneer receiver owners experiencing constant disconnect problems on another forum have now also confirmed they have DAP-1522's.....and they are also pissed after spending countless hours troubleshooting.

I talked to Dlink support today and they will not admit to a problem so I can't wait to contact Pioneer tech support on Monday to let them know I have found the reason they are seeing returns on their new receivers (some cost as much as $7K) since many of the new owners like myself are exchanging them thinking they got a bad one.  I'm sure Pioneer will test this immediately and force a Dlink fix or turn it over to the FCC.At this point I just wish I could get my money back since I have also already confirmed that a netgear bridge works just fine.  Come to think of it, I know Dlink has a new refund policy, but I will check with my state district attorney to see if they can legally keep my money even if the product doesn't work. I don't see anything on the outside of the box with this policy so therfore I wasn't given fair warning of the policy before purchase and would not be expected to know it since it is not industry standard.  Let the games begin.

View 14 Replies View Related

D-Link DAP-1522 :: Won't Accept New Firmware

Mar 14, 2012

I just purchased a DAP-1522. The sticker on the bottom says it's a version B1, with firmware 2.0.In the web interface, it says: "Firmware Version :   1.21 , Fri 26 Jun 2009"I downloaded the 2.01 firmware from the D-Link site and when I try to upload it, it says it's not an image file.

View 11 Replies View Related

D-Link DAP-1522 :: How To Get Ip From Dwl 2100Ap Not By Livebox

Jan 20, 2011

I have bought 1 Dlink Dwl 2100 Access Point about 1 week, it working with ( Default Gateaway 192.168.1.1) but I want connect with 2100Ap But I get Ip from my Livebox Orange.Can I get Ip From 2100Ap (Default Gateway 192.168.0.50), not by LiveBox Orange (Default Gateway 192.168.1.1).My brother live upstair (with LiveBox) I  Live ground Floor and connect to Cable Utp cat5 form upstair to ground Floor. In my room I have a Switch connect to 2100Ap.

LiveBox Orange Default gateway is 192.168.1.1
Dlink dwL 2100Ap Default Gateway is 192.168.0.50
My os is windows Xp sp2

View 2 Replies View Related

D-Link DAP-1522 :: No Internet Access With It

Nov 29, 2010

I have a DIR-655 router with a DAP-1522 connected in bridge mode.  The firmware on the router is 1.21 and the firmware on the bridge is 1.21.  I have my SSID set to broadcast on the DIR-655 with WPA-Personal encryption.  When I initially setup the DAP-1522, I was able to access the setup page and connect to the DIR-655.  On the status page of the DAP-1522, wireless radio is enabled and status is connected.  I connected my XBOX 360, Sony BR player and DirecTV DVR to the wireless bridge and none of them can connect to the internet.

I can wirelessly access the bridge's IP, 192.168.0.50, from any computer connected to the DIR-655 but when I attempt to access the internet on any device connected to the DAP-1522, I do not get a connection.  On the XBOX 360 I cannot connect my live account.  On the Sony BR player, I get a message that new firmware was found, but when it attempts to connect to the internet to download it, the connection times out.  Same occurs when attempting to access the internet on the DirecTV DVR receiver.

View 14 Replies View Related

D-Link DAP-1522 :: Unable To Access It

May 25, 2012

More that a year ago, with guidance from D-Link Customer Service, I performed setup on a system consisting of a DSL-2640B (with wireless disabled) and a DAP-1522 as an access point. I included the 1522 so as to have an N network, since the 2640 is G. The system works fine and I'm able to stream via the 1522 to an N 300 USB Adapter. Internet access is fine, and I'm able to access the 2640 with no problem.I want to add another 300 in a different location. To do that, I'll need to access the 1522 from my Windows 7 computer, since I've lost the passphrase that I'll need for the 300.Everything that I've read tells me to connect the 1522 directly to my computer via cable and to temporarily change the network adapter settinge to:

IP = 192.168.0.x         various sources list values of 2 and 99 for x
Subnet mask = 255.255.255.0
Gateway = 192.168.0.50

Then to use a browser window to go to 192.168.0.50 Regardless of the settings that I use, the browser (IE9) always indicates that it can't connect with that address. accessing the 1522, or on any alternative way to obtain the passphrase.

View 3 Replies View Related

D-Link DAP-1522 :: DIR 655 Quit Working

Feb 14, 2012

My DIR 655 router quit working and so I called D link.  She had me reset the ip to 192.168.5.x.  So now my dap1522 is not connecting to the 655.  I connected the dap1522 to my laptop via ether-net and typed in dink, and got nothing, then put in default ip for the 1522 and still nothing. I also tried ip scanner and it would not come up.

View 1 Replies View Related

D-Link DAP-1522 :: Administration Web Of Switch Is Not Available

Jan 10, 2012

my config : one DAP-1522 as an AP + one DAP-1522 as a switch, 6 meters between them, signal strength about 70. Any others wifi networks around my house. both with FW140b03.bin dated 01/14/2011.Most of the time, both work correctly. But time to time, the wifi link is ko. In AP status, the switch is mentionned connected (uptime = 3 hours ...). The red led is blinking on the switch. The administration web of the switch is not available and the link is ko. Unplug and plug power units doesn't fix the problem. I need to reset DAPs.From Dlink experts, i would like to get more description about issues :

- in switch mode, which are the events modifying the red led state ? what does blinking / off led mean ?

- in AP mode, what does "uptime ...STA ...." mean ? frames are periodically received from STA ?

View 7 Replies View Related

D-Link DAP-1522 :: Comparability With 3D Material?

Aug 8, 2011

Will the dap-1522 work with 3d video ie; from a 3d Blue Ray Player? I am upgrading system to an LED Samsung 3D TV and Samsung 3d Blue Ray Player. I know that HDMI 1.4 cables will work but am looking at the wireless option.

View 1 Replies View Related

D-Link DCS-942L :: Access Camera Directly And RTSP?

Apr 6, 2012

I can access my DCS cameras directly using several iPhone apps such as IP Cam Viewer Pro. Is it possible to access the camera directly using a web browser (I have tried without success) e.g. do you need to use a specific port?Also, the DCS-942L has RTSP. I am not clear as to the difference between RTSP and HTTP streaming of video, any resource that clarifies with respect to D-Link cameras?

View 2 Replies View Related

D-Link DIR-655 :: Connect 3g USB Modem To Router Directly Through Usb Port?

Jan 24, 2013

Can i connect my 3g USB modem to my dlink router directly through the usb port.

View 10 Replies View Related

D-Link DIR-655 :: 10Mbps Up When Connected Directly Through Wired Connections

Nov 11, 2012

I've been trying to find a response or a fix to this issue for a few weeks now.My DIR-655 RevB router is currently at firmware 2.07NA, and has speeds of around 30Mbps down and 10Mbps up when connected directly through wired connections.However over wifi, I am only getting around about 5 Mbps down and 2 Mbps up.  I've tried the 'usual' fixes suggested on here, change broadcast signal to manual, not auto, shutting of QoS shaping, all of that. However nothing seems to be improving the speed. 

View 8 Replies View Related

D-Link DIR-655 :: No Connectivity On Desktop That Is Directly Linked To Router

Aug 29, 2011

I know there are a lot of threads out there regarding connection issues, both with wireless & LAN connections, after updating firmware to 1.35.  To provide a snapshot of my setup...I have 3 GB switches throughout my home, a couple Ethernet enabled Blu-Ray players, 2 XBOX 360's, multiple satellite receivers with Ethernet, 5 PC's, 3 iphones, etc...you get the picture.  I also have 5 older DLink wi-fi cameras.  So, with this said my setup has been flawless for some time.  However, a week or so ago I upgraded my firmware on my DIR-655 to the latest version...everything still seemed fine at the time.  Yesterday I noticed we had no wireless internet so I went and checked.  Sure enough...no connectivity on my desktop that's directly linked to the router, etc.

I tried rebooting & then resetting the router...got connectivity, but as soon as I plugged my PC into the switch...no IP address.  I played around with settings, wiring configurations, etc...I'm pretty up to speed on this setup so I felt I exhausted every option.  I thought my router went bad...gave me an excuse to go get the latest so I brought home a NetGear N750...hooked it up.  As soon as I changed the LAN IP address range to condense the #of IP addresses I'm giving out again, the LAN connection to the PC was lost...I could not get it restored.  I finally got it working, bypassing the GB switch, but the wireless would lose connection literally after a few seconds.

I ended up taking the NetGear router back and bought the exact same DIR-655, but this time it was HW version B1 instead of A and it was firmware #2.00 or something like that.  I hooked it up when I got home...configured the system to exactly the way I had it before and PRESTO!!!  My system is working like it was before.  I can only think that the firmware upgrade I made on the previous router screwed something up in my system. 

View 4 Replies View Related

Cisco Application :: ACE4710 Is Not Able To Link Directly To APP / WEB Server?

Aug 31, 2011

We recently configured a setup to loadbalance 2 application server using ACE4710.  Initially the configuration was to link two app servers directly to ACE4710 without connecting to a Switch, but later, it was advised that ACE4710 is not able to work without connecting to a switch. 
 
1. ACE4710 is not able to link directly to APP/WEB server, but it must go through a network Switch.
 
2. If item-1 above is true.  We used to have a older Cisco Loadbalancer which is able to link directly to WEB/APP servers. What is the reason or advantage of removing this feature?

View 7 Replies View Related

D-Link DAP-1522 :: Unable To Login With Default IP?

Jan 5, 2012

 changed the router wan access pwd and now trying to test the dap i can't seem to log in with the default ip / dlinkap url access i have tried the bridge and ap switch setting on the dap with no luck after resetting the dap a couple of times with no luck ..

View 8 Replies View Related

D-Link DAP-1522 :: How To Enable 5Ghz Band

Oct 13, 2011

I installed my 1522 today with a Direct TV receiver and made a connection using AP mode.

How do I know what band is being used and how to switch between the bads.

View 1 Replies View Related

D-Link DAP-1522 :: DNS Server Not Shown In Static IP

Mar 16, 2012

Under Advanced>DHCP Server, when I put in the Default DNS server of 192.168.0.1 and click save, it goes away. Meaning it doesn't show up anymore.

View 4 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved