I just purchased a DAP-1522. The sticker on the bottom says it's a version B1, with firmware 2.0.In the web interface, it says: "Firmware Version : 1.21 , Fri 26 Jun 2009"I downloaded the 2.01 firmware from the D-Link site and when I try to upload it, it says it's not an image file.
View 11 RepliesI am currently on fw 1.33NA and it works fine just want to update so it works better I've tried the reset to factory and unplugged the internet port and ive tried fw 2.0NA and 2.10NA
View 2 Replies View RelatedI have dap-1522 version A Browser IE8 with lestest updates.
I downloaded the DAP1522_FW_1.31zip went I try to upload via the 1522 admin error not correct file.
I try three different way to download it, could the file be bad on dlinks web site?
I up graded to latest f/w. Now I can only log into the unit for about 1 minute before a get a limited connectivity warning, then it boots me out.
View 7 Replies View RelatedI have my dap-1522 connected to my dir-655 in bridge mode. I was having intermitant connection problems with the dap-1522, so I updated the firmware to 1.41 for version A1. Now when I go to change the connection type to dynamic ip and save, it reverts back to static ip, which makes this thing useless for my network. Why won't it save?
View 6 Replies View RelatedWith firmware version 1.31, the Wireless settings page is blank when a browser other than Internet Explorer is used to access it - for instance, Firefox or Chrome.All other pages appear and seem to work properly, only the Wireless settings page is empty. Luckily, the Wizard still works and can be used to set the Wireless settings for general purpose use. Older versions of the firmware worked fine with other browsers, including the Wireless settings page.
View 6 Replies View Related how to configure AP1522 in my possession.
I have 2 AP1522 and I have to configure them so that clients can connect either 2.4 GHz or 5.0 GHz. Each of the two AP1522 must be autonomous, but has to bear in mind that are close together.
To do this I have:
- Defined the two AP1522 as RAP mode
- Set the flag on the "client access on backhault link", but I have not enabled the sub-flag "Extended backhaul Client Access" (what is this sub-flag?)
- Set 2 BGN different (but this is indispensible or I can put the same BGN? what is the difference?)
- Set the two AP1522 on two different channels (but this is necessary? or is importan only if I set the same BGN?)
- The two AP1522 appear on the WLC as a way bidge (is correct?)
How can I check if my laptop will connect using the 5.0 GHz?!? It's just turn off the antenna of 2.4 GHz?!? On my laptop I haven't found a way to force it to connect in 5.0 GHz.
My current unit is at Firmware Version: v1.02.8 What can I do?
View 3 Replies View RelatedBoth the integrated wireless adapter in my PC and a USB adapter work fine and conect automatically to my D-Link DIR-615 router. I have the integrated adapter disabled in the control panel. Just bought a D-Link DWA-140 Rangebooster N wireless adapter. This finds all the networks my older USN adapter finds but at greater strength. When I click on connect to my own network I get the enter network key box. I enter the correct key, but get an error message telling it's incorrect. I revert to the older adapter or enable the integrated adapter and I get connected automatically.
View 5 Replies View RelatedI get this message in response to clicking on "Diagnose Connection Problems" which was returned to me in I.E. 9 after visiting yahoo.com, other sites and most interestingly, even after trying to get to my DIR-825 at IP address 192.68.0.1. The only common element here is the DIR-825 so I suspect there may be some kind of misconfiguration in the device. The only way that I have been able to clear this condition is to reboot or repower my DIR-825.
View 7 Replies View RelatedI have been working on this problem for the last few day and have know idea why its not working but my d link Dir-615 will not work with my qwest q100 modem.
View 1 Replies View RelatedHave hooked up a DIR-825 to an iMac and it works well on 2.4GHz band. Having issues seeing 5GHz band as it comes and goes. Just today bought a DWA-160 USB adapter hoping it would connect the kid's PS3 to the 5GHz band but the PS3 wont accept or recognize either the DWA-160 or the 5GHz band.
Can't find any solutions in the manuals.Desperate for a fix as the wife and I want to be able to work on the 2.4GHz without being constantly kicked off by the kids on the PS3.
Router does not accept any email address that start with a number. For example, if you want to set email address 1abcd@efg.com in the from field you will receive the following error: The given FROM address (1abcd@efg.com) is invalid. Same error if you use it in the to field.HW ver. A4 running firmware 1.35NA.
View 5 Replies View RelatedRegion : Belgium
Model : TL-MR3040
Hardware Version : V1
Firmware Version : factory default / most recent update
ISP : Mobile Vikings
I was configuring a device for one of our customers, but when I was setting up the MR3040's internet connection settings things went haywire.there's only a default selection for two of my country's providers. No biggy you'd think.
My D-Link DAP-1522 wireless bridge is connected through a single cat5 cable from the LAN port on my PC to the 1st LAN port on the D-link unit. At the moment, it is in bridge mode, with the blue power indicator on, the orange wireless connection light flashing, and the 1st LAN port connection periodically wavering indicating that it is communicating with my PC. When I attempt to configure the DAP-1522 via my internet browser, (IP 192.168.0.50) I get an error saying that the requested webpage does not exist.
View 6 Replies View RelatedI recently had a networking guy set up a VPN for me, but for it to work properly he had to change all my IP addresses to 192.168.10.xx from 192.168.0.xx. My DAP-1522 (in bridge mode) continued to work but I am unable to log on to it, I think because it's address is 192.168.0.0. I have run into some other issues which makes me think I may need to upgrade the DAP-1522 firmware and/or assign it an address beginning with 192.168.10.xx, however I can't log on to the bridge. (Nor do I know how to change or possible reassign the DAP-1522's address through my router, a DIR-615).
View 5 Replies View RelatedMy problem is two-fold:
1. the DAP-1522 will not connect to the 5GHz network of the DIR-815. Although, this doesn't surprise me as none of my 5GHz-capable devices see it, other than intermittently and at low signal. It is most likely an issue with the 815's 5GHz radio/network.
2. OTOH, the 1522 does appear to connect to the 815's 2.4GHz network just fine. However, there is no Internet access for any of the devices connected to the 1522's ports.
I know the 1522 can work correctly on 2.4GHz, as it previously did fine with my prior 2Wire router from AT&T. (I've just switched to Comcast, using the DIR-815 connected to their SMC modem.)
Also, I know the router and modem work fine (at least with 2.4GHz), as all of my wireless devices connect easily and with screaming bandwidth to the router and Internet.
I have a WIN XP desktop which I successfully connected to the 1522 AP - as evidence of the GUI to program it. I have the 1522 set to Bridge Mode via the switch on the unit. The 1522 has hardware version B1 and Firmware version 2.000. I joined my wireless network successfully as evidence of the Status page showing it's successfully connected and bridged to my network. I then disabled my USB wifi NIC in hopes of using my hardwired connection to the 1522 to get on the internet.
Wireless Radio : Enabled
Bridge State : Connected
MAC Address : fc:75:xxxxxx
802.11 Mode : Mixed 802.11a, 802.11g and 802.11n
Band Width : 40
Channel : 6
Network Name
(SSID) : cleveland
Wi-Fi Protected Setup : Enabled
Security : WPA2-PSK
I have just discovered after three weeks of testing that DAP-1522 wireless bridges are not compatible with all the new Pioneer AVR's that support internet radio and Iphone control. Anytime a DAP-1522 is powered on and on the same subnet mask as a Pioneer receiver it will cause the Pioneer to loose it's connection every 30 minutes. The receiver is then not able to connect unless it is powered off and on again. The DAP-1522 will cause this even if the Pioneer is hardwired to a router and nothing is plugged into the DAP-1522. This affects all new models of Pioneer receivers including the Elite line like I have.
I have tested this with 3 differnet Pioneer receivers and 2 DAP-1522's and always got the same results no matter what the settings were and with the 1522 in AP or bridge mode. Other Pioneer receiver owners experiencing constant disconnect problems on another forum have now also confirmed they have DAP-1522's.....and they are also pissed after spending countless hours troubleshooting.
I talked to Dlink support today and they will not admit to a problem so I can't wait to contact Pioneer tech support on Monday to let them know I have found the reason they are seeing returns on their new receivers (some cost as much as $7K) since many of the new owners like myself are exchanging them thinking they got a bad one. I'm sure Pioneer will test this immediately and force a Dlink fix or turn it over to the FCC.At this point I just wish I could get my money back since I have also already confirmed that a netgear bridge works just fine. Come to think of it, I know Dlink has a new refund policy, but I will check with my state district attorney to see if they can legally keep my money even if the product doesn't work. I don't see anything on the outside of the box with this policy so therfore I wasn't given fair warning of the policy before purchase and would not be expected to know it since it is not industry standard. Let the games begin.
I have bought 1 Dlink Dwl 2100 Access Point about 1 week, it working with ( Default Gateaway 192.168.1.1) but I want connect with 2100Ap But I get Ip from my Livebox Orange.Can I get Ip From 2100Ap (Default Gateway 192.168.0.50), not by LiveBox Orange (Default Gateway 192.168.1.1).My brother live upstair (with LiveBox) I Live ground Floor and connect to Cable Utp cat5 form upstair to ground Floor. In my room I have a Switch connect to 2100Ap.
LiveBox Orange Default gateway is 192.168.1.1
Dlink dwL 2100Ap Default Gateway is 192.168.0.50
My os is windows Xp sp2
I have a DIR-655 router with a DAP-1522 connected in bridge mode. The firmware on the router is 1.21 and the firmware on the bridge is 1.21. I have my SSID set to broadcast on the DIR-655 with WPA-Personal encryption. When I initially setup the DAP-1522, I was able to access the setup page and connect to the DIR-655. On the status page of the DAP-1522, wireless radio is enabled and status is connected. I connected my XBOX 360, Sony BR player and DirecTV DVR to the wireless bridge and none of them can connect to the internet.
I can wirelessly access the bridge's IP, 192.168.0.50, from any computer connected to the DIR-655 but when I attempt to access the internet on any device connected to the DAP-1522, I do not get a connection. On the XBOX 360 I cannot connect my live account. On the Sony BR player, I get a message that new firmware was found, but when it attempts to connect to the internet to download it, the connection times out. Same occurs when attempting to access the internet on the DirecTV DVR receiver.
More that a year ago, with guidance from D-Link Customer Service, I performed setup on a system consisting of a DSL-2640B (with wireless disabled) and a DAP-1522 as an access point. I included the 1522 so as to have an N network, since the 2640 is G. The system works fine and I'm able to stream via the 1522 to an N 300 USB Adapter. Internet access is fine, and I'm able to access the 2640 with no problem.I want to add another 300 in a different location. To do that, I'll need to access the 1522 from my Windows 7 computer, since I've lost the passphrase that I'll need for the 300.Everything that I've read tells me to connect the 1522 directly to my computer via cable and to temporarily change the network adapter settinge to:
IP = 192.168.0.x various sources list values of 2 and 99 for x
Subnet mask = 255.255.255.0
Gateway = 192.168.0.50
Then to use a browser window to go to 192.168.0.50 Regardless of the settings that I use, the browser (IE9) always indicates that it can't connect with that address. accessing the 1522, or on any alternative way to obtain the passphrase.
My DIR 655 router quit working and so I called D link. She had me reset the ip to 192.168.5.x. So now my dap1522 is not connecting to the 655. I connected the dap1522 to my laptop via ether-net and typed in dink, and got nothing, then put in default ip for the 1522 and still nothing. I also tried ip scanner and it would not come up.
View 1 Replies View Relatedmy config : one DAP-1522 as an AP + one DAP-1522 as a switch, 6 meters between them, signal strength about 70. Any others wifi networks around my house. both with FW140b03.bin dated 01/14/2011.Most of the time, both work correctly. But time to time, the wifi link is ko. In AP status, the switch is mentionned connected (uptime = 3 hours ...). The red led is blinking on the switch. The administration web of the switch is not available and the link is ko. Unplug and plug power units doesn't fix the problem. I need to reset DAPs.From Dlink experts, i would like to get more description about issues :
- in switch mode, which are the events modifying the red led state ? what does blinking / off led mean ?
- in AP mode, what does "uptime ...STA ...." mean ? frames are periodically received from STA ?
Will the dap-1522 work with 3d video ie; from a 3d Blue Ray Player? I am upgrading system to an LED Samsung 3D TV and Samsung 3d Blue Ray Player. I know that HDMI 1.4 cables will work but am looking at the wireless option.
View 1 Replies View Relatedi have been living in China for some time and bought a DIR-600M router from DLINK while I was there. While a friend configured it for me and everything was fine, i would love to have an english version of the firmware.... i have searched everywhere but couldnt find any english version for this particular model..I have tried to download and install the American version of the 600 model, but it seems as it does not accept this version as it always jumps back to the chinese version after rebooting....
View 1 Replies View Relatedchanged the router wan access pwd and now trying to test the dap i can't seem to log in with the default ip / dlinkap url access i have tried the bridge and ap switch setting on the dap with no luck after resetting the dap a couple of times with no luck ..
View 8 Replies View RelatedI installed my 1522 today with a Direct TV receiver and made a connection using AP mode.
How do I know what band is being used and how to switch between the bads.
Under Advanced>DHCP Server, when I put in the Default DNS server of 192.168.0.1 and click save, it goes away. Meaning it doesn't show up anymore.
View 4 Replies View RelatedDo the devices connected to the DAP-1522 communicate directly with each other or do they communicate through the router.My DAP-1522 is set up as a bridge connected to my DIR-825. The reason I ask is I've set up an HTPC connected to the DAP-1522 and I also have media devices connected to the DAP and am wondering if they'll communicate with each other directly or if they have do it by going to the router and back. That way I can use my HTPC to serve media to my devices at local speeds.
View 1 Replies View RelatedI already have a DIR-855 and was considering using a DAP-1522 in conjunction to bridge my 5GHz N to my living room to feed HD media to my PVR box and also feed wired-only clients like my TV and BR player. But, in my new flat I find that the walls are pretty thick and my wifi signal is dropping off pretty quick, so I was wondering if you can configure the DAP-1522 to simultaneously be a wifi bridge to feed my media clients, and an AP to feed any laptops that might be in use in the living room?
View 1 Replies View RelatedHad to reset out DIR-655 router. This ended up changing our network password. Unfortunately, my DAP-1522 was not informed of this change and it will not connect to my Directv receiver now. I attempted to log into the bridge to change the password and it will not let me in. I attempted to reset the DAP in hopes that I would just be able to start over from scratch, but no dice (Assuming that I did it correctly)
View 4 Replies View RelatedI m setup for my brother's next house. He wants to use to share with my internet access. I do have 2wire modem provider that has wireless capability in my house. So he have DAP-1522 [bridge mode] and adjust in Wireless Setting, to use SSID manual, (Bell9**) WPA. It s successful, and works well. Problem is cannot use wired to computers, blu-ray, Xbox 360 in same time. it will disconnect frequently because in bridge mode doesn't have DHCP reserved?
My bro bought other one is DIR-655. DAP-1522 keep in [bridge mode] to link to DIR-655 (Static IP), and setup DHCP Reserved. He feel relief that works very well and have no problem with any computers and devices doesn't disconnect anymore. my question is why DAP-1522 doesn't have DHCP reserved when bridge mode that connected to any providers modem?