Had to reset out DIR-655 router. This ended up changing our network password. Unfortunately, my DAP-1522 was not informed of this change and it will not connect to my Directv receiver now. I attempted to log into the bridge to change the password and it will not let me in. I attempted to reset the DAP in hopes that I would just be able to start over from scratch, but no dice (Assuming that I did it correctly)
View 4 RepliesI have my dap-1522 connected to my dir-655 in bridge mode. I was having intermitant connection problems with the dap-1522, so I updated the firmware to 1.41 for version A1. Now when I go to change the connection type to dynamic ip and save, it reverts back to static ip, which makes this thing useless for my network. Why won't it save?
View 6 Replies View Relatedi cant create dlink acess point password , if I am going 192.168.0.50 then showing error massages , I am check two three computer , then the same error coming
View 1 Replies View RelatedI recently had a networking guy set up a VPN for me, but for it to work properly he had to change all my IP addresses to 192.168.10.xx from 192.168.0.xx. My DAP-1522 (in bridge mode) continued to work but I am unable to log on to it, I think because it's address is 192.168.0.0. I have run into some other issues which makes me think I may need to upgrade the DAP-1522 firmware and/or assign it an address beginning with 192.168.10.xx, however I can't log on to the bridge. (Nor do I know how to change or possible reassign the DAP-1522's address through my router, a DIR-615).
View 5 Replies View RelatedHow do I change my password to a dlink router?
View 1 Replies View RelatedOn the Dap1522 access point, in access point mode, would it be possible to have the following 2 features implemented?
1) Ability to simultaneously broadcast on the 2.4GHZ AND 5GHZ band.
2) Ability to specify a guest network.
Hardware version: A4, Firmware version: 1.35NA.
The device is working just fine but I just want to change the password but it failed. I opened my web browser enter 192.168.0.1 then logged into the admin account then put in the new password for both admin and user, clicked save setting...it asked for rebooting the device I let it rebooting. Everything went fine. I was able to log in both the admin and user acc with the new password. The only problem is that my PC can still connect to the network using the old password? I expect that the PC will need to use the new password to access the network but this is not the case.
I would like the ability to change the default password. Currently, when I change the default password and save the config via the web interface, neither the original password, or the new password work. I am forced to reset the device to the default config to regain access to the device.
DCS-930L firmware 1.04 and Mac OSX 10.5.8
This is the configuration I am running:Internet > Cable Modem > Netgear WNDR3700 Router ~~ DAP-1522 > Wired Windows 7 PC + Linux PC + Printer.The Windows 7 and Linus PC's do communicate well to the internet as do any laptops accessing the router wirelessly and any devices wired to the router. That is the good news.
The bad news is that any devices located after the DAP-1522, including the DAP-1522 do not show up on the network map of either the router or any of the wireless laptops. Neither does the Win 7 PC connected through the DAP-1522 show any networked devices, whether through the DAP-1522 or not, even though network discovery is turned on.
Right now the DAP-1522 is set up to function as a bridge and is in "Static IP" mode. I tried changing it to DHCP, but the DAP-1522 will not allow saving that setting, even though it will allow changing it. It just reverts back to "Static IP". The firmware version is 1.31, and the firmware update went well after a workable logon to the admin page was discovered. Also the one-button (WPS) set-up to the router worked as far as allowing an internet connection.
What needs to change to allow all the devices to show up on the network maps and maintain internet access? Ultimately, I would like to stabilize the IP's of the major components of the network to make troubleshooting easier. But to do that the devices need to show up on the network maps, particularly of the router, so they can be added to the IP reservation table by selection.
Is it possible to connect the dap-1622 to a hidden network using WPA Radius? I've tried, but didn't succeed. I'm running FW version 1.41. I've tried with older FW versions, and none of them seems to work.
View 1 Replies View Relatedi am using a D-Link 2730u, was trying to change the username and password for the router but it keeps saying that ACS URL is required, there is a place where i can put one but even after goggling it for a bit i didn't understand what should i put in there?
View 1 Replies View RelatedRegion : Others
Model : TL-WR740N
Hardware Version : V4
Firmware Version :
ISP :
how to change my router password?
I Recently purchased the DAP1522 to use as an entertainment bridge for my xbox 360, BR player and dish network receiver I also upgraded my router a WRT5GS running tomato to a Linksys E4200 going from G to N while i had my Xbox and BR connected wireless I didn't have the Dish receiver hooked up so i thought by using the DAP i would be upgrading my network and connecting my Dish receiver no brainier right and everything works so far.But here's the question with all the hype of the benefits of the 5ghz channel , well it's not hype it certainly makes sense but from what I see the products have to be compatible shouldn't what I'm connecting be compatible they say your gaming console specifically and streaming movies i would think . Any configuration tips I read somewhere that with an E3200 router they had to set the 5ghz channel to like 37 for the DAP to see that channel its all getting a little overwhelming here's whats in the house A Mac Power PC pre Intel using a Asus NB13 USB 2.4ghz its the only thing i could find with speeds over 100Mbps A windows 7 machine hardwired gig connection another windows 7 pc downstairs hardwired a netbook with a wireless connection and lastly a DECT 6.0 phone system who knows what interference these produce.
View 1 Replies View RelatedWant to change network name and password
View 9 Replies View Relatedhow do you change the Name and password of your wireless network? i accidently changed the house we are renting for the week and they wouldn't be happy.
View 1 Replies View RelatedHow to change password for wireless network
View 1 Replies View RelatedSimply put, a wireless network was set up with a network name and password in a senior community of primarily beginner users. Recently the name and password became changed to that of a community member named, let's say, "Joe". After addressing the router several times to change things back - only to find that the network name reverted to Joe - I changed the router password from admin to a unique pw and I confirmed that Remote Management was off. Next day... it was Joe again
View 3 Replies View RelatedIn short, I had the following problem in the past but it solved itself when people physically left the area. Now they are back, the problem is occurring and this time I have as many router settings as I can find to maybe aid in the solution.This is the problem:We have a wireless network where the physical equipment is not available to users and yet, the local network name and password continues to be changed wirelessly FROM say, "ABC network" with network password "ABC secret password" to "Jimmy's Network" and network password "some new string of letters and numbers". (we know who Jimmy is but will not approach him until we learn if this situation is inadvertent on his part or more purposeful, which we doubt as of now)Cisco Lynksys Wireless-N Home Router WRT120N[CODE]
View 1 Replies View RelatedI have an established wireless network, using a wired Dell desktop (XP), wireless HP G70-250US notebook (Vista), wireless HP Officejet 650 E709n printer, and Belkin N600 router. To make a long story shorter, both my cable company and Belkin were involved to set up the router a few months ago, and I was assigned an SSID and password that I now want to change. I've received emails from Belkin on changing it at the router - but when it comes to my notebook computer, how to establish a network - I'd like to know how to change the SSID and password in an already-established network, once I've made changes with the router. I'm assuming this is possible? It is my understanding that I don't need to make any changes with my wired desktop, other than to use it when making the router changes? I'm a little familiar with the network configuration setting process with my printer, so am pretty sure I can handle that.
View 7 Replies View RelatedI have an E2500 router. When I enter 192.168.1.1 as a web address I am asked for a User name and password. When I do not enter anything for user name and put “admin” in password the screen again asks me for the same two things and eventually goes to a 401 message.
When I enter admin in user name and my secure password to allow devises to connect to the network it lets me in. I thought the password to enter the system settings and the one to enter the network are usually separate. When I open the Cisco Connect program and go into the various menus there my “secure” password is written and visible for anyone who clicks it. Is this how it is supposed to work?Also, how do I occasionally change the password to enter into the network.
I'm trying to re-setup this EOL camera on a new router.I've been able to reset the cam to factory defaults and see it wired using dhcp. I then was able to change the address to a static address, still wired and still can see it with IE. However when I disconnect the rj-45 cable, power down and restart, I can't access the cam.
View 2 Replies View RelatedMy D-Link DAP-1522 wireless bridge is connected through a single cat5 cable from the LAN port on my PC to the 1st LAN port on the D-link unit. At the moment, it is in bridge mode, with the blue power indicator on, the orange wireless connection light flashing, and the 1st LAN port connection periodically wavering indicating that it is communicating with my PC. When I attempt to configure the DAP-1522 via my internet browser, (IP 192.168.0.50) I get an error saying that the requested webpage does not exist.
View 6 Replies View RelatedWe've been using a 2Wire from our ISP to connect to the internet, and a Dlink DIR 655 for our wireless network. (Since the 655 has "N" speed, we can transfer large files between computers much faster than with the 2Wire.) The setup has worked fine for a few years, but recently both devices were slow. After turning them off and on a few times, unplugging, etc., without much effect, I reset both units. They're working now, but I've lost our network name and password; our Macs (and iPhone & iPad) are now using the default unlocked Dlink network. I tried to input the Dlink's default IP address, 192.168.0.1, but the address never connects. Any suggestions on how I can access our DIR 655's IP address, so I can reinstall a password and network name? If our tech guy (now unavailable) changed the Dlink's default IP address years ago, wouldn't it it have reverted to the 192.168.0.1 when I reset?
View 4 Replies View RelatedMy problem is two-fold:
1. the DAP-1522 will not connect to the 5GHz network of the DIR-815. Although, this doesn't surprise me as none of my 5GHz-capable devices see it, other than intermittently and at low signal. It is most likely an issue with the 815's 5GHz radio/network.
2. OTOH, the 1522 does appear to connect to the 815's 2.4GHz network just fine. However, there is no Internet access for any of the devices connected to the 1522's ports.
I know the 1522 can work correctly on 2.4GHz, as it previously did fine with my prior 2Wire router from AT&T. (I've just switched to Comcast, using the DIR-815 connected to their SMC modem.)
Also, I know the router and modem work fine (at least with 2.4GHz), as all of my wireless devices connect easily and with screaming bandwidth to the router and Internet.
I have a WIN XP desktop which I successfully connected to the 1522 AP - as evidence of the GUI to program it. I have the 1522 set to Bridge Mode via the switch on the unit. The 1522 has hardware version B1 and Firmware version 2.000. I joined my wireless network successfully as evidence of the Status page showing it's successfully connected and bridged to my network. I then disabled my USB wifi NIC in hopes of using my hardwired connection to the 1522 to get on the internet.
Wireless Radio : Enabled
Bridge State : Connected
MAC Address : fc:75:xxxxxx
802.11 Mode : Mixed 802.11a, 802.11g and 802.11n
Band Width : 40
Channel : 6
Network Name
(SSID) : cleveland
Wi-Fi Protected Setup : Enabled
Security : WPA2-PSK
I have dap-1522 version A Browser IE8 with lestest updates.
I downloaded the DAP1522_FW_1.31zip went I try to upload via the 1522 admin error not correct file.
I try three different way to download it, could the file be bad on dlinks web site?
I have just discovered after three weeks of testing that DAP-1522 wireless bridges are not compatible with all the new Pioneer AVR's that support internet radio and Iphone control. Anytime a DAP-1522 is powered on and on the same subnet mask as a Pioneer receiver it will cause the Pioneer to loose it's connection every 30 minutes. The receiver is then not able to connect unless it is powered off and on again. The DAP-1522 will cause this even if the Pioneer is hardwired to a router and nothing is plugged into the DAP-1522. This affects all new models of Pioneer receivers including the Elite line like I have.
I have tested this with 3 differnet Pioneer receivers and 2 DAP-1522's and always got the same results no matter what the settings were and with the 1522 in AP or bridge mode. Other Pioneer receiver owners experiencing constant disconnect problems on another forum have now also confirmed they have DAP-1522's.....and they are also pissed after spending countless hours troubleshooting.
I talked to Dlink support today and they will not admit to a problem so I can't wait to contact Pioneer tech support on Monday to let them know I have found the reason they are seeing returns on their new receivers (some cost as much as $7K) since many of the new owners like myself are exchanging them thinking they got a bad one. I'm sure Pioneer will test this immediately and force a Dlink fix or turn it over to the FCC.At this point I just wish I could get my money back since I have also already confirmed that a netgear bridge works just fine. Come to think of it, I know Dlink has a new refund policy, but I will check with my state district attorney to see if they can legally keep my money even if the product doesn't work. I don't see anything on the outside of the box with this policy so therfore I wasn't given fair warning of the policy before purchase and would not be expected to know it since it is not industry standard. Let the games begin.
I just purchased a DAP-1522. The sticker on the bottom says it's a version B1, with firmware 2.0.In the web interface, it says: "Firmware Version : 1.21 , Fri 26 Jun 2009"I downloaded the 2.01 firmware from the D-Link site and when I try to upload it, it says it's not an image file.
View 11 Replies View RelatedI have bought 1 Dlink Dwl 2100 Access Point about 1 week, it working with ( Default Gateaway 192.168.1.1) but I want connect with 2100Ap But I get Ip from my Livebox Orange.Can I get Ip From 2100Ap (Default Gateway 192.168.0.50), not by LiveBox Orange (Default Gateway 192.168.1.1).My brother live upstair (with LiveBox) I Live ground Floor and connect to Cable Utp cat5 form upstair to ground Floor. In my room I have a Switch connect to 2100Ap.
LiveBox Orange Default gateway is 192.168.1.1
Dlink dwL 2100Ap Default Gateway is 192.168.0.50
My os is windows Xp sp2
I have a DIR-655 router with a DAP-1522 connected in bridge mode. The firmware on the router is 1.21 and the firmware on the bridge is 1.21. I have my SSID set to broadcast on the DIR-655 with WPA-Personal encryption. When I initially setup the DAP-1522, I was able to access the setup page and connect to the DIR-655. On the status page of the DAP-1522, wireless radio is enabled and status is connected. I connected my XBOX 360, Sony BR player and DirecTV DVR to the wireless bridge and none of them can connect to the internet.
I can wirelessly access the bridge's IP, 192.168.0.50, from any computer connected to the DIR-655 but when I attempt to access the internet on any device connected to the DAP-1522, I do not get a connection. On the XBOX 360 I cannot connect my live account. On the Sony BR player, I get a message that new firmware was found, but when it attempts to connect to the internet to download it, the connection times out. Same occurs when attempting to access the internet on the DirecTV DVR receiver.
More that a year ago, with guidance from D-Link Customer Service, I performed setup on a system consisting of a DSL-2640B (with wireless disabled) and a DAP-1522 as an access point. I included the 1522 so as to have an N network, since the 2640 is G. The system works fine and I'm able to stream via the 1522 to an N 300 USB Adapter. Internet access is fine, and I'm able to access the 2640 with no problem.I want to add another 300 in a different location. To do that, I'll need to access the 1522 from my Windows 7 computer, since I've lost the passphrase that I'll need for the 300.Everything that I've read tells me to connect the 1522 directly to my computer via cable and to temporarily change the network adapter settinge to:
IP = 192.168.0.x various sources list values of 2 and 99 for x
Subnet mask = 255.255.255.0
Gateway = 192.168.0.50
Then to use a browser window to go to 192.168.0.50 Regardless of the settings that I use, the browser (IE9) always indicates that it can't connect with that address. accessing the 1522, or on any alternative way to obtain the passphrase.
My DIR 655 router quit working and so I called D link. She had me reset the ip to 192.168.5.x. So now my dap1522 is not connecting to the 655. I connected the dap1522 to my laptop via ether-net and typed in dink, and got nothing, then put in default ip for the 1522 and still nothing. I also tried ip scanner and it would not come up.
View 1 Replies View Relatedmy config : one DAP-1522 as an AP + one DAP-1522 as a switch, 6 meters between them, signal strength about 70. Any others wifi networks around my house. both with FW140b03.bin dated 01/14/2011.Most of the time, both work correctly. But time to time, the wifi link is ko. In AP status, the switch is mentionned connected (uptime = 3 hours ...). The red led is blinking on the switch. The administration web of the switch is not available and the link is ko. Unplug and plug power units doesn't fix the problem. I need to reset DAPs.From Dlink experts, i would like to get more description about issues :
- in switch mode, which are the events modifying the red led state ? what does blinking / off led mean ?
- in AP mode, what does "uptime ...STA ...." mean ? frames are periodically received from STA ?