I am new to these forums and I have upgraded from firmware 1.00 on the DIR-815 to the 1.01 firmware and once I upgraded, I can log into Xbox, but can't host party chats or host game rooms. I also noticed that any and all messages sent from friends didnt show until I rebooted my console. Something is SERIOUSLY WRONG here and would like a MOD to comment on this.
View 12 RepliesI recently bought a new D-Link DIR 615 but I dont get adequate range in the rooms farthest away from the router. I have an old D-Link DIR 634M router which I'm told can be used as a wireless repeater.I went through several articles that describe connecting the two routers through a LAN cable. However is there a way to do the same without using a cable of any sorts?
View 1 Replies View RelatedI am currently using a DIR-655 for the home wireless network.DSL into a 2-Wire home portal (not wireless) and ethernet into the DIR-655.I need to connect a number of wired devices in a couple of different rooms. Some streaming HDTV content to other devices in other rooms. I'm thinking of the following:
-DIR-655 routing between the DSL subnet to the internet, the 2.4GHz wireless and a couple of wired devices.
-DAP-1522 routing between the 2.4GHz wireless, 5GHz wireless, and a few wired devices.
-DAP-1522 bridging between the 5GHz wireless and a few wired devices.
All devices will/may need internet access.HDTV content would be between wired devices and only over the 5GHz wireless (no HDTV to/from internet).Is the DAP-1522 the right device(s) for this?
I had something odd happen to my Dlink router DIR-651 model. During the early evening hours someone changed the SSID name of my Router. Nothing else changed that I could see right off. So I reset the router to Factory Defaults.
View 1 Replies View RelatedXbox works fine for some things, I can access Netflix, can download from live marketplace, etc, but cannot join a party and cannot play a game. Other people cannot join my party, cannot play my game. Error when I try to join a party is "Can't connect to xbox live party, there might be a network problem."
Xbox join party and games work fine when connected directly to comcast (motorola) modem.Dir-601, firware 1.02NA and 101NA. Hardware version A1.Port forwarding TCP 53,80,3074 and UDP 53,88,3074 - also included TCP 80 and 21 to no avail.
Contribute to our DCS IP Camera Third-Party Video Monitoring Software List.Do you have experience using third party software to monitor feeds from your DCS camera? Share your knowledge. post your contributions here: DCS Compatible Software(i.e. sticky at the top of the DCS Software board)
View 1 Replies View RelatedToday I got a new modem, which gave me internet on the computer. I still can't get online on my PS3 or IPOD. How to create a new wireless connection. Also the World icon on the router is red but everything else is green.
View 5 Replies View Relatedi cant connect to most of my friends through xbox and computer, i also cant connect to some games servers. it also says that i have a nat strict. i don't care if my router has no security. i just want my internet to be fast and i can connect to people.
View 1 Replies View Relatedi have a DIR-601. Basic settings, port forwarded for Xbox live and Wolfenstein enemy territory.I have a home PC with a wired connection and a laptop which is set up through wireless. I installed the game Wolfenstein: Enemy Territory on my laptop and every time I start the game and attempt to fetch a server list, my router resets itself. The game works fine when I connect directly to my modem, but not when I connect to my router
View 1 Replies View RelatedI keep getting disconnected from the game "Vindictus". I'm not sure what protocols it uses, but it shouldn't require any configuration on the Router, since it was working fine before. I upgraded the firmware to 4.13 in an attempt to fix the issue, but it didn't work. Some people have suggested "Endpoint filtering" to be set to independent, but I cannot find such an option. Where is the option? I was told it was on the Firewall page, but it is not there (Advanced->Firewall/DMZ). The router is supplied by Virgin Media (ISP) but I'm not sure if that matters.
View 6 Replies View RelatedI have a dlink cable modem and dlink dir-655 router. When the router is first turned on or a setting is changed any/all of the computers here can connect to the Ultima Online game server for login but within a few minutes most will not be able to. Its as if they are being refused a connection to login.owo.com (I think that is where they connect to). 1 maybe 2 computers can still connect but its fickle and can't know which 1 or 2 it will be or for how long.any computers already connected to a game server are fine its just the ones trying to login after the router has been running for a few minutes. My first assumption 2 days ago when this happened with my dlink gaming router was that the router developed a problem but now with a new router its still happening. The problem started when I re-enabled the wireless on my gaming router and when I noticed the problem I re-disabled the wireless but the problem persists. A new modem (the DIR-655) did not work...
View 10 Replies View RelatedIve been trying to work this out on XBL forum for a while. all my settings seem to be correct ( UPnP, NAT type: open, no port forwarding or triggering, IP settings on Xbox's are auto).
The two Xbox can play online separately, when either one of them attempts to join the others party it disconnects from Xbox live.
According to the microsoft website, Xbox live only supports the Hardware version 1A and Firmware: 1.00NA.
My router has B1 and 2.00NA. is there a way to downgrade?
I have a Linksys e3000 and a Linksys WRT120NVery simple setup. the 3000 is in my office. There is a cable that goes from this routerto the living room across the house, it is just laying there. Since I cannot get a wireless signal into that room,I would like, using the cable that is hanging there to make use of the other linksys and provide a wireless signal to the living room, all under the same network. In essence, extending the wireless network using the cable in the living room that is connected to the main router in my office.My question is, without touching the master router, how would I set the 2nd router in the living room up?I understand that DHCP on the 2nd router needs to be turned off, and a channel selected so that it does not overlap. Same SSID, Sam WPA2 key.Or would there be a device better suited for this?I do not want to extend the 2 rooms wirelessly I want to use the cable, then use the wireless in the living room for wireless devices etc.
View 9 Replies View RelatedI have a question about external antennas on an access point. I have to plan a wireles solution, that also includes coverage in the industrial freezers. The freezers are one part of the sotck rooms, so the general coverage will be done with 1602I access points.
Since there are quite a lot of freezers in one location, installing separate AP in every freezer will be very expensive. I wondered if there is a possibility to put one 1602 access point with external antennas outside the freezer and then extend the antennas with 2m cables inside different freezers (1602E has three external antennas, so one antenna to each freezer).
Would this installation even work?
The freezers are quite small rooms maybe 2-3m2 sow the coverage is not a problem. But does this installation support multiple clients per AP in different freezers doing stocktaking with handheld terminals?
One of the persons involved in a home network has installed a Dlink DIR-825 Rev-B Extreme router on the Comcast cable system to allow a 'better' wireless signal on upper floors of the home. Two others involved in the same home network use a 'secure desktop access' software called NetOp to access the network remotely. To facilitate this software, we must 'port forward' port 6502 on BOTH UDP and TCP to the single system that is accessed.
However, this setup (simple port forwarding) does not seem to work - neither does 'virtual server', for that matter. Prior to this router being installed, it was extremely simple to accomplish this remote access using a Linksys router, so our software firewall configuration has not changed but the new Dlink seems unable to allow remote access.
How (and via which of these access methods - port forwarding or virtual server) would be best? This configuration seems frustratingly difficult to accomplish and I'm about to take the Dlink 'out' of the network and re-install the Linksys with a 'high-gain' external antenna to facilitate simple signal enhancement.
Issue: When I attempt to save the changes I made to the DHCP reservation list I get an error window that reads:
http:\201.201.201.201 (my internal router IP address - changed from 192.168.0.1)
Host name Invalid I have a DHCP Range setup as 201.201.201.100 to 201.201.201.199
I'm attempting to reserve an IP address of 201.201.201.199 for one of the computers on my network.
I can see the computer on the dir825 router and am connecting to it through a linksys wrtgs working as a repeater bridge running dd-wrt. The computer in question is successfully getting it's IP address from the dhcp server on the dlink router.
The dir825 is running 2.05na firmware. Why am I unable to reserve an IP address?
I recently upgraded my internet service and received a D-Link DIR-815 from the company as they couldn't get our older router working with the new service (4G)
My brother plays Star craft and you have to forward ports to be able to host games for others to join, but it doesn't work.
I know how to port forward because our old router had exactly the same setup, but I have one issue though, when I look at the DIR-815's manual, and even in posts made by D-Link, I've seen them asking if the filters for the firewall are set to Endpoint Independent for UDP/TCP, now I know where this is, it's under Advanced/Firewall Settings, it even shows it there in the manual, but it's not there at all under my firewall settings, my older DIR router had it and we had no problems port forwarding, I'm not sure if it was removed in a later hardware or something?
I'm just wondering if its possible to ping an IPv4 host using the IPv6 host assuming that the NAT64 has already been implemented?
[code]...
I have a host that can successfully connect to a PIX 515E (7.x OS) via VPN Client; however, I have no IP routing to the LAN from the remote host.The VPN IP pool works finem,The LAN default gateway is the inside interface on the PIX; the network is flat L2 behind it.The default route on the PIX points out; no other routes are defined,The VPN remote host can be pinged from LAN hosts, but the VPN remote host cannot ping any LAN host, not even the PIX inside interface.
View 2 Replies View RelatedASA 5510
Ver 8.2(5)
I have been looking all over the place for the answer of how to allow clients on an IPSEC VPN to ping from host to host.
I've been trying to set-up DMZ for my DSL-2542B-SE_1.00_06112008.
But the problem is when I access my IP from WAN, It connects to Router Control Panel, I have set DMZ IP as 192.168.1.2 which is the my computer where I have the Server set-up.
Now I've disabled DMZ but still I can access to my router from WAN through my IP.
I use wireless internet connection and I see “third party setup = Yes under configuration. Is it about sharing data or being monitored
View 1 Replies View RelatedAny 3rd party CA to provide a root cert for the ACS & verify csr's generated by the 7925's? I've spoken with customer service at Verisign and GeoTrust and either i'm explaining it totally wrong or their not providing CA services for this type of secured environment. sHA1 using EAP-TLS.
View 1 Replies View RelatedI have a school club, but our school does not allow any wireless networks within the school perimeters.Wired are allowed, but wireless are not allowed.I plan to host a LAN party for my club, and we will have about 20-30 people.We cannot have any internet access, and I have not touched a wired stuff, There is a 24 ethernet switch, and if I buy one, and suppose I buy another 24 ethernet switch (I know there is a 48 ethernet switch), can I connect those two 24 ethernet switches to make 47 ports?* For a LAN party without internet access, can we use an ethernet switch or do we use something else?* For 20-30 people, it is recommended that we have a ~8mbps upload speed. When ethernet switches advertise 10mbps, is that upstream & downstream? When all the computers are hooked to 24 ports, does the advertised 10mbps go lower? (I have seen 100/10 mbps, and I don't know what that means)
View 4 Replies View RelatedI'm trying to connect a few of my devices to the wireless internet at home.
1.Xbox 360
2.Galaxy Tab 10.1
3.My Touch 4g
All of them can recognize the the network they just will not connect. All my freq are good 2.4 or 2.5. WEP Key works no problem, just the minute I try to connect the galaxy tab and cell phone just says "remembered, secured with WPA/WPA2 PSK." The xbox when running the test connection fails as well.
Running vista x64 home premium on HP DV7 1270us.
I would like to use the NCS 1.2 to monitor Juniper SRX 210 firewall. When I try to import the MIB File from NCS, which show "Error: Failed to load MIB File "mib-802" because it is not in the resource path.what I can upload the MIB File from Juniper. [code]
View 0 Replies View RelatedI have came across some third-party ws-g5483's that I was thinking of using. But when I go to plug them in, nothing seems to happen. I have tried them in ws-c3548-xl-en and also a ws-c3524-pwr-xl-en with the same results. I know on the newer switches you can do the serviice unsupported-transceiver command but is there anything I can do to get these to work with older switches?
View 5 Replies View RelatedI am using a cisco asa5520 and i have set up remote access vpn with an AnyConnect connection profile.In the connection profile i have set up that users should authenticate using both certificate and AAA.Due to a high security requirement, the user certificate is issued from a 3rd party. This is working fine and the user now need a valid certificate and a username/password to authenticate successfully.I added the CA certificate as a associated trustpoint on the ASA box to get the certificate verification working.Problem:If Jane and Joe both have a valid certificate AND a valid username/password, Jane could authenticate using a combo of Joes certificate, and Janes username/password. Both are valid (isolated), but i only want jane to be able to authenticate with her username/password and her personal certificate.
View 1 Replies View RelatedI'm responsible for designing the network for a LAN party that will be held in October. There will be up to 400 participants and 25-30 crew members. 10 table rows, 40 participants and one 48-port gigabit switch on each table. Core network will be a couple of Cisco 3560G or similar. There will be 2xGbit between the table and core switches.So, how to set up VLANs and subnets for a 400+ people network?
1) Everything on one /23 subnet, or
2) Participants on one /23 subnet, separate subnets for servers, crew and wireless, or
3) Participants on two /24 subnets, separate subnets for servers/crew/wireless, or
4) Separate /26 subnets for each table switch and for servers/crew/wireless?
As far as I can see, the main disadvantage of all participants on one subnet is troubleshooting and isolating network problems - and the main disadvantages of separate subnets is more complex setup and that people cannot browse LAN games other than those on the same switch.
Does any one used third party SPF in Cisco ASR 1002 series routers, does it supports them.
View 2 Replies View RelatedI am thinking about running some third-party unified communications apps under VMWare ESXi5 on a Cisco SRE 900 module. According to the Cisco docs, third-party apps are supported on these modules (see table below) but the app in question is NOT on Cisco's list below.
[URL]
Some questions:
1. As long as the third-party app is capable of running under VMWare/VSphere ESXi5, is there anything on the SRE that would prevent you from running this third-party app even though it's not on Cisco's list?
2. What is Cisco's policy on the use of third-party apps that are not on their list? For example, will they take a support call on the SRE running a non-listed app. (I don't want to void any sort of support contract through the use of a third-party app not on their list).
I'm fairly new to networking but I've learned quite a bit on my own without being educated. I'm trying to just figure things out on my gear. So for my LAN party i'm going to need an internet connection. I'm not going to rely on my venues subnet though so i want to create a new /24 subnet(250 hosts is good for a start). I want my subnet to be able to speak to the outside network too.
View 8 Replies View RelatedI am attempting to install a third party SSL cert (GoDaddy) to properly secure the external interface of my 1811 ISR so that I can implement SSL VPN. I have tried using SDM 2.5, but that doesn't appear to be working. I am familiar with doing this on a Cisco 3005 Concentrator, but I'm not aware of how to install an intermediate cert on the 1811 (or if it's even possible), in order to properly have the GoDaddy cert properly imported and used for SSL VPN. I have gone through the CSR process and have the initial cert from them generated and have imported it, but it never appears to be identified correctly if I browse to the external interface on the router. The router always defaults to its self-signed cert.
View 1 Replies View Related