What Is Third Party Setup Configuration
May 24, 2012I use wireless internet connection and I see “third party setup = Yes under configuration. Is it about sharing data or being monitored
View 1 Replies
ADVERTISEMENT
Cisco 3560G - LAN Party Network Setup?
May 20, 2012I'm responsible for designing the network for a LAN party that will be held in October. There will be up to 400 participants and 25-30 crew members. 10 table rows, 40 participants and one 48-port gigabit switch on each table. Core network will be a couple of Cisco 3560G or similar. There will be 2xGbit between the table and core switches.So, how to set up VLANs and subnets for a 400+ people network?
1) Everything on one /23 subnet, or
2) Participants on one /23 subnet, separate subnets for servers, crew and wireless, or
3) Participants on two /24 subnets, separate subnets for servers/crew/wireless, or
4) Separate /26 subnets for each table switch and for servers/crew/wireless?
As far as I can see, the main disadvantage of all participants on one subnet is troubleshooting and isolating network problems - and the main disadvantages of separate subnets is more complex setup and that people cannot browse LAN games other than those on the same switch.
Linksys Wired Router :: Proper RVS4000 Configuration Behind A 3rd Party Router
Mar 16, 2011I need properly configuring the RVS4000 device. I need all devices to be on the same subnet (192.168.0.x) and if I am drawing this out correctly in my head I would perform the following:Connect LAN port of RVS4000 to LAN port of the switch and statically assign a LAN IP of 192.168.0.251 to the RVS4000Switch is connected to LAN port of the 2Wire (192.168.0.254)Change operating mode from Gateway to Router in the RVS4000 Connections to the RVS4000 will obtain a DHCP IP address from the 2Wire that's upstream.As the WAN port of the RVS4000 would be unused, will it still answer requests for a VPN connection assuming the proper ports are forwarded to it?
View 1 Replies View RelatedCisco :: 3rd Party CA For ACS And 7925g
Mar 27, 2013Any 3rd party CA to provide a root cert for the ACS & verify csr's generated by the 7925's? I've spoken with customer service at Verisign and GeoTrust and either i'm explaining it totally wrong or their not providing CA services for this type of secured environment. sHA1 using EAP-TLS.
View 1 Replies View RelatedLAN Party With Ethernet Switch Without Internet?
Oct 10, 2012I have a school club, but our school does not allow any wireless networks within the school perimeters.Wired are allowed, but wireless are not allowed.I plan to host a LAN party for my club, and we will have about 20-30 people.We cannot have any internet access, and I have not touched a wired stuff, There is a 24 ethernet switch, and if I buy one, and suppose I buy another 24 ethernet switch (I know there is a 48 ethernet switch), can I connect those two 24 ethernet switches to make 47 ports?* For a LAN party without internet access, can we use an ethernet switch or do we use something else?* For 20-30 people, it is recommended that we have a ~8mbps upload speed. When ethernet switches advertise 10mbps, is that upstream & downstream? When all the computers are hooked to 24 ports, does the advertised 10mbps go lower? (I have seen 100/10 mbps, and I don't know what that means)
View 4 Replies View RelatedCan't Connect To Third Party Devices Via Wireless
Jul 29, 2011I'm trying to connect a few of my devices to the wireless internet at home.
1.Xbox 360
2.Galaxy Tab 10.1
3.My Touch 4g
All of them can recognize the the network they just will not connect. All my freq are good 2.4 or 2.5. WEP Key works no problem, just the minute I try to connect the galaxy tab and cell phone just says "remembered, secured with WPA/WPA2 PSK." The xbox when running the test connection fails as well.
Running vista x64 home premium on HP DV7 1270us.
D-Link DIR-615 :: SSID Name Changed By Third Party?
Jan 13, 2012I had something odd happen to my Dlink router DIR-651 model. During the early evening hours someone changed the SSID name of my Router. Nothing else changed that I could see right off. So I reset the router to Factory Defaults.
View 1 Replies View RelatedCisco :: SRX 210 NCS 1.2 Import Third Party MIB File
Feb 21, 2013I would like to use the NCS 1.2 to monitor Juniper SRX 210 firewall. When I try to import the MIB File from NCS, which show "Error: Failed to load MIB File "mib-802" because it is not in the resource path.what I can upload the MIB File from Juniper. [code]
View 0 Replies View RelatedCisco WAN :: Ws-g5483 / Using Third-party GBICs?
May 2, 2011I have came across some third-party ws-g5483's that I was thinking of using. But when I go to plug them in, nothing seems to happen. I have tried them in ws-c3548-xl-en and also a ws-c3524-pwr-xl-en with the same results. I know on the newer switches you can do the serviice unsupported-transceiver command but is there anything I can do to get these to work with older switches?
View 5 Replies View RelatedHow To Setup Configuration And Security After Reset
Feb 24, 2012How to set upo configuration & Security after reset
View 2 Replies View RelatedFS762T Networking Setup And Configuration
Mar 7, 2012I have a Router, Modem, Switch, and a Switch.
Firewall: FVS338
Switch: FS762T
I have networking skills but I am unsure of how to properly configure routing so that everything can be seen on the network and access internet.Switch is for all towers/servers and router is for laptops.
Cisco VPN :: 3rd Party Certificate And AAA Authentication ASA 5520
Oct 24, 2011I am using a cisco asa5520 and i have set up remote access vpn with an AnyConnect connection profile.In the connection profile i have set up that users should authenticate using both certificate and AAA.Due to a high security requirement, the user certificate is issued from a 3rd party. This is working fine and the user now need a valid certificate and a username/password to authenticate successfully.I added the CA certificate as a associated trustpoint on the ASA box to get the certificate verification working.Problem:If Jane and Joe both have a valid certificate AND a valid username/password, Jane could authenticate using a combo of Joes certificate, and Janes username/password. Both are valid (isolated), but i only want jane to be able to authenticate with her username/password and her personal certificate.
View 1 Replies View RelatedCisco WAN :: ASR 1002 - Use Third Party SPF In Series Routers?
Sep 4, 2011Does any one used third party SPF in Cisco ASR 1002 series routers, does it supports them.
View 2 Replies View RelatedCisco Infrastructure :: SRE 900 Support For Third-party Apps?
Apr 23, 2012I am thinking about running some third-party unified communications apps under VMWare ESXi5 on a Cisco SRE 900 module. According to the Cisco docs, third-party apps are supported on these modules (see table below) but the app in question is NOT on Cisco's list below.
[URL]
Some questions:
1. As long as the third-party app is capable of running under VMWare/VSphere ESXi5, is there anything on the SRE that would prevent you from running this third-party app even though it's not on Cisco's list?
2. What is Cisco's policy on the use of third-party apps that are not on their list? For example, will they take a support call on the SRE running a non-listed app. (I don't want to void any sort of support contract through the use of a third-party app not on their list).
Cisco Firewall :: Setup ASA Configuration With GNS3?
Jan 12, 2013I'm about to setup as ASA configuration with GNS3 ASA. how to best test the configuration once complete? I need something like a verification plan to ensure that the configuration would perform if in production.
View 1 Replies View RelatedCisco LAN :: 1901 Wireless Setup Configuration
Jun 1, 2012we had this cisco router 1901 in one of our remote office and the management wants to configure 4 wireless pc's to only talk to each other for security reasons.
1. is this possible to do in wireless? i know in VLAN this can be done by assigning pc's in port in a switch.
2. if possible, how to implement this setup
Foundry Fesx424 Layer 3 Switch Routing For LAN Party
May 5, 2012I'm fairly new to networking but I've learned quite a bit on my own without being educated. I'm trying to just figure things out on my gear. So for my LAN party i'm going to need an internet connection. I'm not going to rely on my venues subnet though so i want to create a new /24 subnet(250 hosts is good for a start). I want my subnet to be able to speak to the outside network too.
View 8 Replies View RelatedD-Link DIR-825 :: Can't Host Party Chats Or Game Rooms
Oct 24, 2011I am new to these forums and I have upgraded from firmware 1.00 on the DIR-815 to the 1.01 firmware and once I upgraded, I can log into Xbox, but can't host party chats or host game rooms. I also noticed that any and all messages sent from friends didnt show until I rebooted my console. Something is SERIOUSLY WRONG here and would like a MOD to comment on this.
View 12 Replies View RelatedD-Link DIR-615 :: XBOX Can't Join Party Or Play Games
Jun 22, 2011Xbox works fine for some things, I can access Netflix, can download from live marketplace, etc, but cannot join a party and cannot play a game. Other people cannot join my party, cannot play my game. Error when I try to join a party is "Can't connect to xbox live party, there might be a network problem."
Xbox join party and games work fine when connected directly to comcast (motorola) modem.Dir-601, firware 1.02NA and 101NA. Hardware version A1.Port forwarding TCP 53,80,3074 and UDP 53,88,3074 - also included TCP 80 and 21 to no avail.
Cisco Security :: How To Apply 3rd Party Certificate To 1811 ISR
Sep 29, 2009I am attempting to install a third party SSL cert (GoDaddy) to properly secure the external interface of my 1811 ISR so that I can implement SSL VPN. I have tried using SDM 2.5, but that doesn't appear to be working. I am familiar with doing this on a Cisco 3005 Concentrator, but I'm not aware of how to install an intermediate cert on the 1811 (or if it's even possible), in order to properly have the GoDaddy cert properly imported and used for SSL VPN. I have gone through the CSR process and have the initial cert from them generated and have imported it, but it never appears to be identified correctly if I browse to the external interface on the router. The router always defaults to its self-signed cert.
View 1 Replies View RelatedCisco AAA/Identity/Nac :: Wireless With ACS 5.2 And 3rd Party Access Point
Nov 15, 2012I have windows 7 clients (supplicants), D-link access point (authenticator), Cisco acs 5.2 virtual appliance with evalution license (acts as authentication server - Radius server). I want to setup EAP authentication (PEAP) that users will be able connect to Wireless LAN with login-password. I've done some configurations, but I did not get any result. in ACS 5.2 I get this error message: 11014 RADIUS packet contains invalid attribute(s): RADIUS Request dropped.
View 5 Replies View RelatedCisco :: Reloading Renewed 3rd Party Cert On WLC 5508?
Apr 22, 2012So since my web auth cert is expiring I got it renewed from VeriSign and they sent me back the file. Do I need to again combine the "myprivatekey.pem" file and the new one that I got and then load it on the WLC? Can't find any guidelines and instructions from Cisco on this. Or do I need to go through the whole regenration of CSR process again etc?
View 3 Replies View RelatedPatch Panel To Firewall / How Current Setup Is Done There Is No Configuration Map
Mar 16, 2011I have DSL, a firewall, patch panel and hubs.The network was already in place by three previous techs. I am not sure how the current setup is done there is no configuration map.The users in office 1 are all connected to a patch panel that then connects to hubs The second office users connect to a hub that then connects to the patch panel then connects to another hub.The internet is connected to a router that will be replaced with a firewall. Should it be setup like thisdsl modem > firewall > patch panel > hubs > Nodes
View 3 Replies View RelatedCisco Firewall :: ASDM 6.2 Configuration Tab Comes With Setup Wizard
Feb 7, 2012Everything was working fine till one day, when clicking on Configuration Button you see setup wizard prompt.It's ASDM ver:6.2 and ASA 8.2. Everything is working fine, but now unable to change any rules.
It there simple cure for that?
AAA/Identity/Nac :: Cat4500e ISE Support On Third Party Switch Doing 802.1x Authentication On Interface
Jun 8, 2013how ISE support on third party LAN switch, if the requirement is doing 802.1X based flexauth.Refer to the diagram i attached; 01 topology.png
Concern 1: if the 3com switch with 802.1X feature, but still without the full feature to support FlexAuth, policy encforcement, DACL etc. In this kind of situation, will user still able to authenticate (using method PEAP-MSCHAP v2), but authorization just grant with permit any any?
Concern 2: Can i assume i authenticated the 3com switch using MAB? But this will cause endpoint with no 802.1X, am i right?
Concern 3: cisco switch C4507-E, loaded with IOS version Cat4500e-UNIVERSALK9-M, version 03.04 and Supervisor Engine :WS-X45-SUP7-E, is this platform is supported in Cisco TrusctSEC?
Cisco Routers :: RV120W Installed Behind Third Party Firewall And QuickVPN
Feb 13, 2012We have just installed a Cisco RV120W behind a third party firewall. All works correctly now, but we are struggling to get the Quick VPN clients connected. I have enabled port forwarding for PPTP & L2TP over IPSEC on the third party router, but still cannot connect (the RV120W was previously used as a primary router & worked perfectly). What ports do I need to open on the third party router to get this to work correctly?
View 4 Replies View RelatedCisco Application :: Third Party Payment Gateway Design For CSS115003
Dec 16, 2011I have a scenario.On our website, there is an option to pay mobile,electrycity etc bill from payment gateway (third party). when user click on that link, my servers(behind CSS) should go to paymrent gateway using their SSL cert (payment gateway SSL cert) and should provide payment gateway link to user on our website.
How to implement this scenario using CSS115003 ?
user access URL---click on Payment Gateway---My servers get authenticated from pyament gateway using their cert--revert back and provide payment gateway link to user on URL.
Cisco Firewall :: ASA5510 / Specific Configuration About TCP Connection Or DNS To Setup?
Mar 8, 2011I Changed my old firewall by an ASA5510, since that change my internet connexion is slower.Some websites takes longer to display.I would like to know if there are some specific configuration about TCP connection or DNS to setup?
I just configured the ISP DNS :
Dns server-group DefaultDNSname-server 194.2.0.20 name-server 194.2.0.50
Cisco Switching/Routing :: To Setup NVI On 1941 Router - Configuration
Dec 9, 2012Here is my current config, how to enable and setup NVI on a cisco 1941 router.i think it would fix my issue but i'm unclear on how to implement it to test.
i would like to be able to access an internal server from an outside address.
Cisco Switches :: SLM 2024 - VLAN Configuration / 4 Ports Setup
Aug 13, 2012I'm new to managed networking. So I'm having trouble understanding how to set up my switches properly. I have a closed network with about 20 switches and 2 IDF's. No router, and no internet. I have a SLM 2024 in want to have 4 ports set up with a VLAN. I have another SLM2024 I want to be on the same VLAN some where else. Switch 1 uses port 24 GBIC as and up link port to one of the IDF's. Switch 2 uses ports 12 and 24 copper(LACP) to make a hop from another switch(ports 1 and 13 LACP)which inturn is connected to the same IDF on port 24 GBIC. How do I set up switch 1 ports 7,8,19,20? Also, how do I set up switch 2 ports 7,8,19,20? VLAN 11
View 1 Replies View RelatedCisco :: CUCM Calling Party Info - User Extension Number?
Mar 21, 2012In CUCME if you do not configure any translation rules and leave the system mainly at default, when a call is routed to the PSTN the CUCME system sends the true calling party ID which would be a users extension number. Is it correct to assume that a CUCM server based system, when too left at the majority of default (without translation rules or stripping etc) that it will send the true calling ID to the gateway?
View 1 Replies View RelatedD-Link DCS-930L :: Contribute To Our Third-Party Video Monitoring Software List
Nov 23, 2011Contribute to our DCS IP Camera Third-Party Video Monitoring Software List.Do you have experience using third party software to monitor feeds from your DCS camera? Share your knowledge. post your contributions here: DCS Compatible Software(i.e. sticky at the top of the DCS Software board)
View 1 Replies View RelatedCisco VPN :: 1941 - How To Make Remote Clients To Access Third Party IP Address
May 23, 2013I've got a Cisco 1941 setup working fine for Cisco Anyconnect. Clients can connect to local resources fine. The issue I have is I need the remote clients to access a third party IP address but to do so they must do it through the VPN. At the moment only local resources are accessed across the vpn and if they need internet they use their own internet connection they are connecting with.I've added the below to make sure traffic going to the IP is going across the VPN.
View 4 Replies View Related