Cisco Routers :: RV120W Installed Behind Third Party Firewall And QuickVPN
Feb 13, 2012
We have just installed a Cisco RV120W behind a third party firewall. All works correctly now, but we are struggling to get the Quick VPN clients connected. I have enabled port forwarding for PPTP & L2TP over IPSEC on the third party router, but still cannot connect (the RV120W was previously used as a primary router & worked perfectly). What ports do I need to open on the third party router to get this to work correctly?
View 4 Replies
ADVERTISEMENT
Aug 22, 2011
The PPTP client from Windows 7 is not working with this router; therefore I would like to try the quickvpn.Is there any paper from Cisco explaining how to setup the RV120W for quickvpn ?
View 1 Replies
View Related
Oct 29, 2011
I have been battling with my Cisco RV120W router and QuickVPN.Running Windows 7 Home PremiumPerformed a fresh install to factory out-of-box install for WindowsRemoved NortonDid NOT perform any windows updatesInstalled QuickVN version 1.2.4.1I have updated the firmware to the latest version (confirmed by cisco)I can connet to the router and have a stable connectionI can ping both the router IP and the shared file server IPWhen I enter the shared file server IP into the search field (e.g. \192.168.100.199) and press enter, I see a connection to "share", so I click on this and then see "FolderName" of my shared files. I click on this folder and I get a timed out error.When I enter the routers IP address into a browser (IE8 as factory installed) I get a timed out error also.In the past, I have installed all important and recommended updates for Windows and still get the same scenerioI have called cisco support and went through router settings, assigned them a VPN username, they log in and can access the files without issue (What the @#$$@#$)Cisco support spent plenty of time with me, but since they could access my network and since I could ping my devices, they had no other suggestions further.
I have this fresh factor out-of-box install. I know this is most likely something to do with my laptop that I am trying to use to connect to the network. I have Frontier as my ISP for home. I don't know if there is anything they are doing to interfere with my connection. I have tried to connect to the network via ComCast as well, with no luck.tell me if there is something I need to tweak in my Windows 7 settings?
View 11 Replies
View Related
Mar 6, 2012
I have a Cisco RV120W connected to the internet. I have configured a QuickVPN user on the router, but I cannot connect via QuickVPN no matter on what PC I try (with firewall or without firewal, Windows XP, 7, ...). On the router it says the VPN user is connected, but on the client PC I receive remote gateway not responding. In the logs it says failed to ping remote VPN router. I tried changing all settings I could find on this forum, but the result stays the same (changed port to 60443, deleted all IKE and VPN policies, allowed ping, disabled fragmented packets etc...). None of all the settings seems to get any result.
View 11 Replies
View Related
Jan 15, 2013
have a Cisco RV120W and I need setup a Quick VPN user, however i can't enable this user.I have Remote Management enable, access type All Ip Address and port number 443.
View 3 Replies
View Related
Jan 1, 2012
I am trying to install a Cisco VPN Router RV120W behind this router. I have setup the Cisco and can access the internet from the device. I also setup the Actiontec router with the DMZ host as the Cisco router. When I try to connect to the VPN tunnel however I connect but receive an "Gateway is not responding" error message after 30sec. Is there anything else I need to setup on the actiontec router to allow VPN passthough or something like that?
Actiontec Lan IP: 192.168.1.1
Cisco Wan IP: 192.168.1.2
Cisco Wan SN: 255.255.255.0
Cisco Wan Gateway: 192.168.1.1
Cisco WAN DNS: 192.168.1.1
71.250.0.12
Cisco Lan IP: 192.168.20.1
Edit: I have also tried this connection from a Windows 7 Pro with Firewall enabled and also Windows XP with the same error.
Quick VPN log:
2011/12/30 00:05:58 [STATUS]OS Version: Windows 7
2011/12/30 00:05:58 [STATUS]Windows Firewall Domain Profile Settings: ON
2011/12/30 00:05:58 [STATUS]Windows Firewall Private Profile Settings: ON
2011/12/30 00:05:58 [STATUS]Windows Firewall Private Profile Settings: ON
2011/12/30 00:06:10 [STATUS]OS Version: Windows 7
2011/12/30 00:06:10 [STATUS]Windows Firewall Domain Profile Settings: ON (code )
View 9 Replies
View Related
Nov 8, 2011
Is there a way to set up Quick VPN on the RV120W without changing the internal subnet? I have just taken over responsibility for a network and I don't know all of the nooks and crannies yet, so I'd rather not change the internal sub net. I've tried setting up a user then changing the LAN settings afterward, but it automatically removed the VPN user when I did so.
View 1 Replies
View Related
Jul 5, 2012
I have a problem with firewall rules. If I set some rules for open communication and some for closed, so I cannot reorder from the end to begin.
Last rules are at the end of all. So I can only reorder in one pages.(I have about 33 rules = 3 pages of rules)
View 4 Replies
View Related
Feb 16, 2012
We have had our router and remote computers set up with Quick VPN for over a year. We've had our share of problems but have worked around them.
Now, out of the blue, no one can connect to the VPN. I went in to try to do some 'troubleshooting' and the ONLY thing that allows our VPN connection to go through is to completely disable the RV016 firewall. We have too many remote users to actually start and stop the firewall everytime someone needs the VPN connection.
View 1 Replies
View Related
Sep 4, 2011
Does any one used third party SPF in Cisco ASR 1002 series routers, does it supports them.
View 2 Replies
View Related
Apr 2, 2012
what exactly is QuickVPN?Is it a IPSec VPN?Is it a PPTP?Is it a SSLVPN?can I resolve my local hostnames? That means, can I configure a lokal DNS Server?
View 3 Replies
View Related
Feb 7, 2012
I would like to set up a site to site VNP connection between 2 RV120W routers, preferably via IPsec.
The problem is that I would like/have to use a 4G modem router (model TINY) which connects to internet in front of the RV120W (on the local side)
I have no problem with that on the remote site that RV120 connects directly to internet via a public IP address on the WAN port.
Local network 192.168.1/24-----RV120W----192.168.100.1—Tiny---Public IP--------INTERNET
INTERNET--------PublicIP—RV120W—Remote local network 192.168.2/24
View 1 Replies
View Related
Oct 21, 2011
So have a RV042 VPN router that is directly connected to the ethernet port of our comcast cable modem.
If I connect to it using QuickVPN (1.4.2.1) from a PC that is connected using AT&T 3G Network it works fine!
If I connect to it using QuickVPN (1.4.2.1) from a different PC that is connected using home WiFi (linksys wrtxxx) then it fails. In the VPN log all I see is failure messages for ping.
2011/10/22 15:47:28 [WARNING]Failed to ping remote VPN Router!
If I open a regular command prompt and attempt to ping the VPN router it works so not understanding why the QuickVPN is unable to ping.
how I can troubleshoot this further. Makes me think the RV042 config is fine otherwise it would not work on a 3G connection. Something on the home PC or the home network. Not sure what to check.
View 2 Replies
View Related
Mar 11, 2012
I've one RV042. I've configured VPN PPTP and it work (I've redirect port 1723 on router1 to rv042). If I can try to use quickVpn, client login and receive error "remote gateway is not responding". I have redirect port 60443 from router1 to rv042. Connection it's this: INTERNET-router1-RV042.
View 3 Replies
View Related
Dec 11, 2011
I've deployed a WRVS4400N router at one of my clients, however I'm unable to access resources on his network via DNS. I was hoping to use the router for DNS resolution, however when I connect via VPN, I can only connect to shares via IP address.
View 1 Replies
View Related
Oct 6, 2011
I got a RSV4000 router here with the latest firmware 1.3.3.5, trying to get the quick VPN client to connect.As far configurations go I have under WAN set the IP, subnetmask, DNS1, DNS2 and gateway. And under VPN I have created a client account with a password, created and then exported the Cert to my client PC.But when I attempt to connect, the QuickVPN software hangs for a few moments at "Connecting" and then fails; when the general error.I'm running this on Windows 7 x64.
View 1 Replies
View Related
Sep 21, 2011
Today I purchased a RV042 wired router. I set the VPN connection but when I try to login using QuickVPN, get stucks in "Verifying network". I checked the logs:
2011/09/22 20:43:45 [STATUS]OS Version: Windows 7
2011/09/22 20:43:45 [STATUS]Windows Firewall Domain Profile Settings: ON
2011/09/22 20:43:45 [STATUS]Windows Firewall Private Profile Settings: OFF
[Code]...
From my side Im connected to a WRT54G2. VPN Passthrough enabled. Windows 7 Pro x64. No 3rd party AV or firewall. Windows Firewall disabled, also tried enabling it.
From the RV042 side it has a Static IP Address configured. DHCP server enabled. HTTPS enabled. UPnP disabled. L2TP disabled.Firewall disabled. Block WAN Requests disabled.
View 6 Replies
View Related
Jan 12, 2012
I've a RV120W with the last firmware version (june 2011), i want to create two vpn tunnel:
- Professional: lan routing all packet for the 192.168.0.0/24 to the first VPN tunnel
- Other: all other address IP destination to a second VPN tunnel
The first tunnel (professional) is ok but what rules can i use to configure the second ?
View 2 Replies
View Related
Feb 8, 2012
What is the default login/pass of cisco rv120w for ssh access ?
View 1 Replies
View Related
Sep 24, 2011
Upgraded to 1.0.2.6 and all of a sudden SIP devices working over the VPN no longer work. Downgrade to 1.0.1.3 and they work again. My guess is that some ports are blocked over the VPN in 1.0.2.6
I thought the general idea was that firmware ugrades fixed bugs rather than introducing them.
Suggestion for Cisco:- Zip the firmware image downloads, or else have an upgrade process that includes a CRC check, that way at least the poor punter will have an indication if they have been corrupted. I had a subtle memory problem that was corrupting some files. The firmware upload appeared to complete properly and you could log on OK but some of the menu choices resulted in a hang with the "Please wait... the page is being loaded" message. Careful checking of file sizes revealed that the file I was uploading into the router was a few hundred bytes different in size to the one on the website, must have been corrupted during the download. But the upload proceeded normally with no indication of any error. It's a pretty basic safeguard that should be in there as a matter of course with the router performing a CRC check and showing an error if it fails.
View 2 Replies
View Related
Mar 31, 2012
I had WRT54G2 and recently switched to an RV120W. I have an Internet accessible camera system connected to my router. Before, this worked fine... there is a dns service (DynDNS.com) that is configured as part of the camera setup. I would then just enter [URL] and I would connect to the cameras. I install the new router (RV120W) and I can no longer connect to the cameras. I do not recall any configuring that I had to perform on the old router.
why the RV120W isn't letting me get to the cameras?
View 3 Replies
View Related
Sep 12, 2011
Rx:, recently I have perchase 2 RV120W routers thinking that it must be very easy to setup the site to site vpn. i cannot get my remore office to link to my main office and vice verser.
Scenaro
- I'm using 2 RV120W routers for each site.
- Site A using a subnet of 192.168.10.0 mask 255.255.255.0
- Site B using a subnet of 192.168.11.0 mask 255.255.255.0
I have setup the VPN using the wizard and I got site to site tunnels connected and show as 1/1 Connected (1 user) in the status he IPsec connection status show
--Policy Name: VPNA
--Endpoint : public IP address from my ISP 203.117.222.221
--Packets Tx:145 Rx:0 and Kbytes shows Tx: 29.55 Rx:0
Q1 why I cannot use dynamic DNS naming in the policy setting ? eg: aaa.dyndns.org, I have to use the ip address instead eg: 203.117.222.221
Q2. I cannot connect from Site A to Site B , I can't even do a ping to 192.168.11.1 from Site A. even though it show the Site to site tunnel is coonected.
View 2 Replies
View Related
Aug 6, 2012
I've just set up an IPSec VPN between 2 x RV120W which are both behind other router. Here's what we have :
RV120W #1 (192.168.1.254) --- (192.168.1.1) Office Router #1 (PUBLIC IP) --- (((Internet))) --- (PUBLIC IP) Office Router #2 (192.168.2.1) --- RV120W #2 (192.168.2.254)
It works great, tunnel is UP.
[Code]....
View 1 Replies
View Related
Nov 21, 2012
I've just set up an IPSec VPN between 2 x RV120W which are both behind other router. Here's what we have :
RV120W #1 (192.168.1.254) --- (192.168.1.1) Office Router #1 (PUBLIC IP) --- (((Internet))) --- (PUBLIC IP) Office Router #2 (192.168.2.1) --- RV120W #2 (192.168.2.254)
[Code]....
Now, I need to be able to reach the server (192.168.1.100) from a PC on LAN #2 with IP 192.168.2.50. So, I've created au static route on Office Router #2 (192.168.2.1) because of course it doesn't know how to reach private subnet 192.168.1.x. My static route looks like this :
192.168.1.0 / 24 (Destination network) --- 192.168.2.254 (Gateway)
...but it doesn't work, no ping. When I do a tracert to server IP (192.168.1.100) from PC on LAN #2 (192.168.2.50), the result is :
1st jump ---> 192.168.2.1
2nd jump --> 192.168.2.254
...and it doesn't go further.
View 3 Replies
View Related
Jun 28, 2011
I have router Linksys RV042 v1.2 with latest firmware Version: 1.3.13.02-tm. And I'm using QuickVPN v 1.4.1.2. I've setup VPN connection with values, below: But every time I'm trying to connect to router by VPN it always popup a window "Remote Gateway not responding".It occurs when I'm trying to connect to VPN behind other router, when I'm connected directly to Internet the connection is established.But I'm connecting to other networks using VPN and it's working properly (behind the same router), so I think it's problem with RV042 configuration but I don't now weher.
View 5 Replies
View Related
Aug 10, 2010
I did upgrade to WiSM from v5.1 to V6 then i see this log %WCP-3-KEEPALIVE_LOST: wcp_controller_server.c:1763 Lost keepalives from Cat 6K Supervisor.
View 6 Replies
View Related
Oct 1, 2012
I've been working on getting a client to Gateway configuration going for quite some time now. Had it working with a different Cisco single wan router that failed. The user replaced the router with an RV042 and we are trying to get the QuickVPN to once again connect to the router as it did before the replacement. Previously we did connect successfully with Windows 7 clients.
Router: RV042 v3 firmware 4.0.4.02-tm Quickvpn version 1.4.2.1
what i keep getting in the log is the following :
2012/10/02 12:55:07 [STATUS]OS Version: Windows Vista
2012/10/02 12:55:07 [STATUS]Windows Firewall Domain Profile Settings: ON
2012/10/02 12:55:07 [STATUS]Windows Firewall Private Profile Settings: ON
[Code].....
View 5 Replies
View Related
Sep 11, 2011
I have a RV082 in the corporate office, and several remote people connecting to it using QuickVPN through a variety of clients (XP and Windows 7). As of today, they are all now seeing the "Remote Gateway is not responding - disconnect or wait" message. Checking through the logs on some of the remote clients, I see the "Failed to ping the remote router" message several times, followed by the "Ping was blocked, which can be caused by an unexpected disconnect." message.
The odd thing is that everyone has been running very well over the past 2-3 weeks - most people with 8+ hours of solid connectivity. We made no changes to the clients, nor to the remote router in the corporate office.
View 3 Replies
View Related
Oct 11, 2011
I just bought a RV220W for my small company. I have read everywhere that this model come with 25 license for QuickVPN/IPsec.But when I tried to create all my account I had a bad surprise. The firmware tell me that the maximum number of user that I can create is 10! I dont see anywhere in the firmware where I can upgrade for another licence. I have the last firmware.
View 7 Replies
View Related
Oct 11, 2011
When I use QuickVPN under XP, I connect to my RVS4000 without problems. When I switch to new computer running Windows 7 and V4.2.1 QuickVPN I can get all the way to Verifying Network. Then I get the message that: "The remote gateway is not responding. Do you want to wait?" - repeatedly. The icon in the tool bar remains with a red slash and I am unable to ping devices on the lan side of the router. However, when I check the VPN Summary on the router, I see that it thinks I'm connected. When I check the VPN log I see that I am not:
Oct 12 10:27:53 - Configuration changed!
Oct 12 10:28:33 - Configuration changed!
Oct 12 10:28:34 - [VPN Log]: added connection description "ValR_rw_rw"
[Code]....
I've disabled MS Security Essentials and made sure the Firewall is on. IPSec Policy Agent and IKE and AuthIP IPSec Keying Modules services are both started. I've created a rule to allow QuickVPN throught the firwall in and out and a rule to let traffic on 443 and 60443 UDP and TCP through the Firewall.
View 19 Replies
View Related
May 15, 2013
I want to ask if is possible to configure the RV180 behind my DSL Router to connect using QuickVPN. First I tried to connect to the PPTP server and worked fine, but when I tried to connect using QickVPN, seems to connect but when the client says "verifying network" after a while appears the message "network not responding..."
In my DSL-Router forwared this ports: UDP: 500,4500,443,60443 - TCP: 443,60443 (i don't know if tcp ports are needed but I opened for testing) and allowed protocol ESP (comes with the rule to allow IPSEC-L2TP)
View 3 Replies
View Related
Mar 10, 2013
I have a problem with my RV110W router. I would like to setup Quick VPN access. Manual is quite straightforward: enable management, create users, install client and that's all, should be working. But NOT. it does not work.
Remote Management is enabled on port 8080. Should it be changed to 443 as required for QVPN? Or it does not matter. Is it ok, to have management on 8080 and QVPN on 443?
I have tried to connect via QVPN Client ver. 1.4.1.2. Of course ip as well as user and pass has been changed. I tried to change management port to 443, but first:
1. i was not able to access management console at all
2. QVPN - still did not work
View 4 Replies
View Related
Dec 19, 2011
Using QuickVPN from one RV220W to another RV220W I cannot access the Webpage of the remote router. Goes to "CERTIFICATE NOT VALID" then click through that, and the the login page will not come up. Sceen flashes a hint of blue background, then turns white, then just sits there saying "Waiting for response from ???.???.QuickVPN will sucessfully connect and I can use all computers behind the router. Just cannot access the Webpage of the remote router. I can access the Webpage of the local router.Also, when I hookup using QuickVPN from an "Internet Cafe" that is using a Netgear router. I can then access the webpage on both remote routers (of course, depending on whom I QuickVPN'd into at the time).
Location #1
Office #1
RV220W: RV220W-A-K9-NA SER: SER15140314Firmware: 1.0.3.5
IP: 192.168.63.1
Location #2
Office #2
RV220W: RV220W-A-K9-NA SER: SER151600R2
Firmware: 1.0.3.5
IP: 192.168.2.1
I have called Cisco on this with no luck. They said to update my JAVA. I am currently JRE 6 Release 30 and still no luck. The Log files reveal nothing and are darn near unreadable since there is no line breaks in the log file. Have to manually edit the log to pick stuff out.
View 1 Replies
View Related
