Cisco Routers :: RV042 Configuration With QuickVPN In Windows 7
Oct 1, 2012
I've been working on getting a client to Gateway configuration going for quite some time now. Had it working with a different Cisco single wan router that failed. The user replaced the router with an RV042 and we are trying to get the QuickVPN to once again connect to the router as it did before the replacement. Previously we did connect successfully with Windows 7 clients.
Router: RV042 v3 firmware 4.0.4.02-tm Quickvpn version 1.4.2.1
what i keep getting in the log is the following :
2012/10/02 12:55:07 [STATUS]OS Version: Windows Vista
2012/10/02 12:55:07 [STATUS]Windows Firewall Domain Profile Settings: ON
2012/10/02 12:55:07 [STATUS]Windows Firewall Private Profile Settings: ON
[Code].....
View 5 Replies
ADVERTISEMENT
Oct 21, 2011
So have a RV042 VPN router that is directly connected to the ethernet port of our comcast cable modem.
If I connect to it using QuickVPN (1.4.2.1) from a PC that is connected using AT&T 3G Network it works fine!
If I connect to it using QuickVPN (1.4.2.1) from a different PC that is connected using home WiFi (linksys wrtxxx) then it fails. In the VPN log all I see is failure messages for ping.
2011/10/22 15:47:28 [WARNING]Failed to ping remote VPN Router!
If I open a regular command prompt and attempt to ping the VPN router it works so not understanding why the QuickVPN is unable to ping.
how I can troubleshoot this further. Makes me think the RV042 config is fine otherwise it would not work on a 3G connection. Something on the home PC or the home network. Not sure what to check.
View 2 Replies
View Related
Mar 11, 2012
I've one RV042. I've configured VPN PPTP and it work (I've redirect port 1723 on router1 to rv042). If I can try to use quickVpn, client login and receive error "remote gateway is not responding". I have redirect port 60443 from router1 to rv042. Connection it's this: INTERNET-router1-RV042.
View 3 Replies
View Related
Sep 21, 2011
Today I purchased a RV042 wired router. I set the VPN connection but when I try to login using QuickVPN, get stucks in "Verifying network". I checked the logs:
2011/09/22 20:43:45 [STATUS]OS Version: Windows 7
2011/09/22 20:43:45 [STATUS]Windows Firewall Domain Profile Settings: ON
2011/09/22 20:43:45 [STATUS]Windows Firewall Private Profile Settings: OFF
[Code]...
From my side Im connected to a WRT54G2. VPN Passthrough enabled. Windows 7 Pro x64. No 3rd party AV or firewall. Windows Firewall disabled, also tried enabling it.
From the RV042 side it has a Static IP Address configured. DHCP server enabled. HTTPS enabled. UPnP disabled. L2TP disabled.Firewall disabled. Block WAN Requests disabled.
View 6 Replies
View Related
Jun 28, 2011
I have router Linksys RV042 v1.2 with latest firmware Version: 1.3.13.02-tm. And I'm using QuickVPN v 1.4.1.2. I've setup VPN connection with values, below: But every time I'm trying to connect to router by VPN it always popup a window "Remote Gateway not responding".It occurs when I'm trying to connect to VPN behind other router, when I'm connected directly to Internet the connection is established.But I'm connecting to other networks using VPN and it's working properly (behind the same router), so I think it's problem with RV042 configuration but I don't now weher.
View 5 Replies
View Related
Feb 10, 2013
A client of mine has a Cisco RV042 Router. I've configured it to run VPN and it works, sort of. Some clients can connect, others can't, for no discernible reason.
Specific machine issues are Windows 7 x64 or x86, Quick VPN latest release, unobtrusive (Avast or Microsoft Security Essentials) security, etc. 2 separate machines on the same home remote network, 1 can connect just fine, the other can't. My laptop (Win7 x64) connects just fine, one of my techs can connect OK, the IT support guy that works for this client can connect.
Particulars of the router: Firmware version: v4.0.4.02; PID VID : RV042 V03; Firmware MD5 Checksum : 1f84d8d0a2a8b99f9bfa4409e64547aa
View 3 Replies
View Related
Nov 15, 2011
I have a RV042 router setup with Client to gateway VPN access, and am connecting with a W7 PC running QuickVPN. We have many PC's that already have the standard CiscoVPN client on them, is it possible to configure the RV042 to allow these clients to conenct? I'm not sure how to get the Mutual authentication to work, or how to import the PEM certificiate into that client. It seems to allow it to import, but I can never select it.
View 2 Replies
View Related
Nov 15, 2012
I used to have the problem where QuickVPN keeps on trying to verify the network because the RV042 cannot get the final ping to the client.I then bought a RV042 HW version 3 on the VPN side and I installed RV042's at the clients as well.This may look like overkill but believe me, it gives peace of mind, it made things a whole lot better, everybody happy.I am going to set up tunnels but for the time being the clients use QuickVPN. The above setup is all good if people access the vpn from the same source.
I now have a problem where one of our people is in Vietnam and she cannot access the vpn due to the "verifying network" loop.Looking at the log everything looks great, I compared a successful connect with an unsuccessful one and the logs are identical.The only difference is that the final ping is blocked (recorded in the QuickVPN log on the client side).The client uses W7 with firewall on.No need to repeat suggestions, such as turing printer sharing off, I have been through all that. isn't this simply caused by the ISP in Vietnam blocking pings ?
View 2 Replies
View Related
Nov 15, 2010
So here is my issue. I have two sites, each with a Linksys RV042 on thier site.
Site 1:
External: 142.142.142.142
Internal: 192.168.25.0/24
Site 2:
External: 143.143.143.143
Internal: 192.168.26.0/24
We have setup a site-to-site VPN between these sites, and all traffic is running back and forth without isse.
At Site 1 we have configured the Client VPN for use with the QuickVPN software. Again, for site 1, this is not an issue. We are able to access all internal resources at Site 1 without issue (expect for some DNS related problems).
The problem that we have is attempting to access Site 2 resources via the QuickVPN connection at Site 1. Even though they are not suppose to exist, we are able to ping 192.168.26.1-6 (which are ghost addresses likely created by the RV042's) but no actual systems on at Site 2.
I have added the Client VPN connection at Site 2, but it has the same problem accessing resources at Site 1.
View 6 Replies
View Related
Jan 27, 2012
I am setting up remote access using an RV042 router. Using quickvpn or a client-to gateway vpn and shrewsoft client, I can only access/ping the LAN side of the remote router and one machine on the remote network. The PPTP server and native Windows 7 connection provide access to all machines on the remote network.I have 2 possible reasons for this and would like to find the real reason:
1) The remote RV042 is behind another router, and that router restricts access other than the PPTP traffic.
2) The VPN tunnels other than PPTP only allow access to the remote LAN side of the router and remote machines that have the remote router defined as their gateway in the IP configuration.
View 2 Replies
View Related
Oct 29, 2011
I have been battling with my Cisco RV120W router and QuickVPN.Running Windows 7 Home PremiumPerformed a fresh install to factory out-of-box install for WindowsRemoved NortonDid NOT perform any windows updatesInstalled QuickVN version 1.2.4.1I have updated the firmware to the latest version (confirmed by cisco)I can connet to the router and have a stable connectionI can ping both the router IP and the shared file server IPWhen I enter the shared file server IP into the search field (e.g. \192.168.100.199) and press enter, I see a connection to "share", so I click on this and then see "FolderName" of my shared files. I click on this folder and I get a timed out error.When I enter the routers IP address into a browser (IE8 as factory installed) I get a timed out error also.In the past, I have installed all important and recommended updates for Windows and still get the same scenerioI have called cisco support and went through router settings, assigned them a VPN username, they log in and can access the files without issue (What the @#$$@#$)Cisco support spent plenty of time with me, but since they could access my network and since I could ping my devices, they had no other suggestions further.
I have this fresh factor out-of-box install. I know this is most likely something to do with my laptop that I am trying to use to connect to the network. I have Frontier as my ISP for home. I don't know if there is anything they are doing to interfere with my connection. I have tried to connect to the network via ComCast as well, with no luck.tell me if there is something I need to tweak in my Windows 7 settings?
View 11 Replies
View Related
Oct 11, 2011
When I use QuickVPN under XP, I connect to my RVS4000 without problems. When I switch to new computer running Windows 7 and V4.2.1 QuickVPN I can get all the way to Verifying Network. Then I get the message that: "The remote gateway is not responding. Do you want to wait?" - repeatedly. The icon in the tool bar remains with a red slash and I am unable to ping devices on the lan side of the router. However, when I check the VPN Summary on the router, I see that it thinks I'm connected. When I check the VPN log I see that I am not:
Oct 12 10:27:53 - Configuration changed!
Oct 12 10:28:33 - Configuration changed!
Oct 12 10:28:34 - [VPN Log]: added connection description "ValR_rw_rw"
[Code]....
I've disabled MS Security Essentials and made sure the Firewall is on. IPSec Policy Agent and IKE and AuthIP IPSec Keying Modules services are both started. I've created a rule to allow QuickVPN throught the firwall in and out and a rule to let traffic on 443 and 60443 UDP and TCP through the Firewall.
View 19 Replies
View Related
Sep 21, 2011
Is there a safe way to use the Cisco VPN Client (V5.x) and Cisco Quick VPN (V1.4.1.2) on the same Windows PC? I need to access my office RVS4000 and my customer's PIX 506 from the same laptop (but not at the same time).
Perhaps I should be asking "Is there a single Windows VPN client that works with both the Cisco RVS4000 and Cisco PIX 506? I have seen these questions asked on various forums but have yet to see a definitive answer.
View 2 Replies
View Related
Dec 17, 2011
Using the latest Cisco QuickVPN, my Windows 7, 64 bit laptop processes the QuickVPN connection to the point where the laptop attempts to ping the router and verify the connection. Those pings fail.Windows firewall is ON and IPSEC is started on the laptop. I have tried Kaspersky's firewall both enabled and disabled with no change.
View 19 Replies
View Related
Sep 13, 2011
I have a home network with an Actiontec Q1000 providing me 20 meg down and 5 meg up speeds. The DSL modem supports DHCP, DMZ, port forwarding, application forwarding, filtering, etc. I have an existing network 192.168.0.x that uses a combination of DHCP and static IP addresses for printers, scanners, and servers.I just purchased a RVS4000 and configured its LAN port to accept a DHCP address. It received the .26 address. I set up application and port forwarding so all VPN traffic goes to this address. I also put the router in the DMZ and turned off all firewalls.On the LAN side of the RVS4000 I use the 192.168.1.x address and have the 4000 provide DHCP addresses. I have a PC connected to the LAN port and it has the address of 1.100. I am able to use TeamViewer to connect to this through the internet and I can also access the devices on the Actiontec network from the PC connected to the 4000.I set up the VPN as best I could while going through appendix B of the admin guide. When I am at a remote location and use the QuickVPN client to access the 4000 I get the message, "The remote gateway is not responding. Do you want to wait?'. When I look at the log everything looks good except I get the following error:
[WARNING]Failed to ping remote VPN Router!
I am unable to get a DHCP address for my remote PC and am unable to ping any device on either network. What do I have configured wrong that this is not working?I only purchased this so I can use the VPN. Is the VPN established on the Actiontec LAN or on the RVS4000 LAN side? I am obviously connecting to the 4000 but am just not getting an address so I can not use my home office network for all my communications.
View 1 Replies
View Related
Nov 21, 2012
I have a Cisco RV082 and can successfully connect with the Cisco QuickVPN Client, 1.4.2.1. However, after 1 to 5 minutes I see the Windows 7 bluescreen indicating that the system has halted due to a problem with a driver. I have installed the latest Windows updates and reinstalled the client.
The bluescreen only occurs if I use the Cisco QuickVPN Client.
View 4 Replies
View Related
May 29, 2013
I installed QuickVPN v1.4.2.1 as it was in the download section on Linksys: [URL]
for the RV082 router we have. It connected but the program seemed buggy as there seemed to be no way to close the program after I used it so I wanted to uninstall it and install a more recent version of QuickVPN (side question: is it possible to VPN connect to my RV082 router with a different version of QuickVPN?).
I have Windows 7 Professional 64bit SP1 with all the latest updates. When I try to uninstall the program, at about the 25% mark of the window for 'QuickVPN Client Setup is preparing the InstallShield Wizard, which will guide you through the rest of the setup process. Please wait.' it seems to stop responding as holding the mouse over that windows just displayes a ring which goes round and round. I regret installing this buggy software on my PC.
View 3 Replies
View Related
Sep 15, 2011
I recently installed a new RV120W router at one of my customer's office. I have 2 users connecting using the Quick VPN software.The first one is running on a Windows XP Pro SP3. Everything works great on this PC.The second PC is running on a Windows Vista - The QUICKVPN client stays at Veryfing Network and Eventually I get an error " The remote gateway is not responding. Do you want to wait?I have disabled Firewall on both PCS for troubleshooting purposes.
View 1 Replies
View Related
May 20, 2012
i was planed to make a vpn over rv042 so i get the rv042 connected behind a thosmon 456(configured as a bridge) and 1 static ip ... and i configured the vpn and worked great ...but due to some circumstance i get a package of 6 ips insted of the old ip , so when i try to configure the router with the ISP they but the wan ip 10.232.x.x and told me that an internal ip from there lan ... and give me the 6 ip of 196.x.x.x to use as 1 for internal interface for the rv042 and 5 for the pc's,now the vpn not working anymore...notice: when try to configure the vpn tunnle in the local securty setting i mark the ip only and the ip that abear is the wan ip 10.232.x.x but i can't ping that ip beside i can ping the internal ip of the router 196.x.x.50does rv042 can support static and virtual ip inside the lan |! can i configure the thomson as pppoe and use one static ip from 196.x.x.x as wan ip for it ... and use anther 196.x.x.x ip for the rv042 to get access from outside and connect the lan to the rv042 with internal ip 192.168.x.x ...so i can access the vpn from outside .....and can connect the device i need to use static ip to the thomson ...
View 0 Replies
View Related
Apr 19, 2012
I am looking to configure RV042 for VPN access to local machines and Win 2008 server. The story: Had issues with remote printers being created for clients logging into old Linksys RV042 with Linksys VPN software. First Tech exposed server without security, and it had to be removed as it was being attacked, but did not fix printing issue. 2nd tech could not get VPN to work after 1st tech. 3rd tech, 4hours, and I got that the router is a piece of ... So I'm out over 1000, and not able to have a simple router set up. The present situation. New RV042 with firmware V4.1.1.01, using Cisco VPN client 5.0.07.0410, most XP 32 bit machines coming into network, one 64 bit win 7. My clients have been unable to access their data for too long.
View 3 Replies
View Related
Jun 29, 2012
I have just purchased the RV042 and while it is working great on WAN1 over Xfinity/Comcast broadband, I'm unable to get it working with my AT&T DSL for WAN2. I am planning on running this in failover mode - not load balancing.
The DSL modem it is connected to is a SpeedStream (hooking up laptop directly works etc. etc.). The SpeedStream is set to PPOE authentication passed in via the computer (in this case the RV042). On the RV042 side, I set it to use PPOE, using the credentials as given my AT&T DSL. The DNS servers are set to the ones recommended
View 4 Replies
View Related
Oct 28, 2011
I'm running Cisco QuickVPN on a clients laptop (Windows 7). Windows firewall is disabled because McAfee SaaS is running.I sometimes have the issue that the initial connection attempt comes back with "Gateway not respoding" during the network verification process. You close the program, you open it again and it works. Sometimes it takes 2 or 3 tries. Today I have the issue that my client tried it like 20 times including several reboots and it's just not working. I tried it from my own computer and it connected fine on the 2nd try.I'm thinking that it might be time-out thing, that the VPN client doesn't receive a response fast enough? I know my clients home internet is darn slow.
View 1 Replies
View Related
Oct 25, 2012
Yesterday I have purchased a new rv042 router, If i enter url...I have access to a menu but nothing is shown when I follow the menu link.
View 6 Replies
View Related
May 15, 2013
I am not having much success setting up a IPSec VPN tunnel between a RV042 V3 running v4.0.0.07 firmware and PIX 525 running 8.0(4) code.
Let's say the configuration looks like this:
The RV042 has public IP 70.0.0.1 and private LAN IP 192.168.1.1 /24 The PIX has outside IP 69.0.0.1 and inside LAN IP 172.16.0.1 /24 The RV042 is running as DHCP server on it's private LAN A Windows server at 172.16.0.2 is the DHCP server on the PIX's inside LAN.
I've tried every option on the RV042 for Phase 1 and Phase 2, but I am not certain how to configure the Advanced features especially Aggressive Mode, Compress, Keep-Alive, AH Hash Algorithm and Dead Peer Detection.
On the PIX I've tried the basic setup through ADSM, but it's not as clear or obvious to configure both sides with compatible settings compared to setting up a tunnel between two RV042s.
View 1 Replies
View Related
Apr 24, 2013
I Can't see the far video when run the video conference. the audio is working fine.How to config the port forwarding for video conference?
View 1 Replies
View Related
Sep 24, 2006
my office network is running using a Linksys Router RV042 and at home i have a Linksys Router BEFVP41. i'm trying to setup a QuickVPN from home to my office but having problems. both routers have different LAN IPs. the firmware version for my two routers are listed belowRV042 - ver. 1.3.7.4BEFVP41 - ver. 1.02.00?
View 5 Replies
View Related
Apr 8, 2012
I wanna block the Lan IP address(eg:192.168.2.106) to visit wan web, and allow it to lan.How can i set it in access rules?
View 2 Replies
View Related
Nov 11, 2010
Any working configuration to connect the iPad VPN-client (IPSEC) to the RV042?
View 16 Replies
View Related
Mar 20, 2013
I recently bought my daughter a refurshed dell 17" laptop which has Windows 8 home edition on it. She also has another smaller laptop with windows 7 on it, an X-box-360 and a PS3 all connected to this RV042 Business router.
I do not have access to the firmware version of the RV042. I believe it was updated in 2011 or early 2012.
We found out that with the RV042 firewall set to ON, she is UNABLE to hit her college website with the new win 8 computer
She CAN go to the college web site with the smaller win 7 computer when the firewall is off or on.
The win 8 computer will allow google searches, but when you click on any of the links, it will not load.With the win 8 computer, facebook will not load, MSN and Hotmail will not load.
Disable firewall, and most (if not all) items that did not work, magically DO work when the RV042 firewall is disabled for the win 8 laptop.
Having issues with with win 8 home edition and the RV042 firewall enabled? Is there a "simple" cure for this, other than slicking the laptop and putting win 7 on it?
View 3 Replies
View Related
Jul 18, 2011
Im able to create a gateway tunnel with two rv042 routers in different locations ( i can see the tunnel connected in the router) but the quick vpn utility is not working , i also tried to use the pptp as server as an alternative( im able to connect using windows connection to the pptp server but whenever I browse any of the four ip's allowed for the pptp server \10.0.0.200-204 it takes me to the documents of the local computer....I attached the configuration for one of the routers it is the same as the other end , just the information is flipped.
Message was edited by: Adrian Torres
View 7 Replies
View Related
Nov 26, 2011
I have an RV042 using Quick VPN to connect to a remote network. I have port 1723 forwarded to a static IP address on a Windows 7 Pro 64 bit PC. I can establish the VPN and ping a printer but not the Win 7 PC. I can not acccess any shares on the pc via the IP address. It has Norton Antivirus and Windows Firewall. This remote PC replaced a Windows xp PC that allowed access to the shares. I have tried access with a Windows XP Pro and Windows Vista Home Premium PC. Neither have worked.
View 1 Replies
View Related
Apr 23, 2013
I have got two CISCO RV042 .I need to configure a site to site VPN .
View 1 Replies
View Related
Feb 21, 2013
I run 2 RV042 V1 for home and office with Gateway to Gateway VPN connection with single WAN connection in use. Everything works like a charm!
I was even able to create VPN connection with 2 WAN connection on one Router and 1 WAN connection on another with Smart link failover and VPN Tunel Backup.
I got problem though when i tried more complex connection diagram. [URL]
So basically I now have 2 ISP connections on each point with Static IPs and I'd like VPN Connection to be alive for ALL 4 options automatically with failovers (smart links) And tunel backups but i'm not sure if that's ever possible with my equipment.
View 2 Replies
View Related
