Cisco Routers :: VPN Configuration For Dual WAN On Dual RV042
Feb 21, 2013
I run 2 RV042 V1 for home and office with Gateway to Gateway VPN connection with single WAN connection in use. Everything works like a charm!
I was even able to create VPN connection with 2 WAN connection on one Router and 1 WAN connection on another with Smart link failover and VPN Tunel Backup.
I got problem though when i tried more complex connection diagram. [URL]
So basically I now have 2 ISP connections on each point with Static IPs and I'd like VPN Connection to be alive for ALL 4 options automatically with failovers (smart links) And tunel backups but i'm not sure if that's ever possible with my equipment.
View 2 Replies
ADVERTISEMENT
Dec 10, 2012
2 router to connect my phone system to a Sip trunk provider router and to extend my Lan segments so the phone system have internet access.i need it this way because i cant put 2 default gateway in my phone system so the cisco Rv042 is the default gateway of the phone system and i use port fowarding of the UDP ports 5060 to point to the system.and i also use protocol binding of these ports to the Wan 1
Phone system connect to a switchport The sip trunk router connect to the Wan 1 My lan is connected to the Wan 2 Everything is working fine exept this intermittent issue : Each hour or so my sip trunk stop working. to make it start working i need to unplug my Wan 2 connection and wait for 1 minute.
View 4 Replies
View Related
Aug 19, 2011
I need configuring Cisco RV042 dual wlan and port forwarding for 2 servers web and dns in LAN
View 1 Replies
View Related
Jan 7, 2013
I'm in the process of finding a dual WAN router with VPN support, that allow me to redirect some traffic to one specific WAN port and do load balancing of that specific traffic in case of that WAN failing (this last requirement is preferably but isn't fully needed).
Does the RV042/G could work with that? In that case, does it allow protocol redirect only? What about ip/ports redirecting? Or some kind of packet filtering to redirect to specific WAN ports?
View 6 Replies
View Related
Apr 22, 2013
Cisco RV042 Dual WAN VPN Router -how to configure dynamic DNS without having to use the pre-programmed DDNS companies that are populated by default if my DDNS company is not listed and you cannot manually enter another company that is not on the list?
View 1 Replies
View Related
Mar 29, 2012
I wanted to ask a question about the diagram I have included. We are bringing up 2 MPLS WAN connections and would like some specifics on the best design. We are using BGP to the providers. From there we have big questions. We can run BGP internal and are licensed to do so on the N5K's. The N5Ks are currently using HSRP for inside LAN clients as default gateway. We want to load balance and provide redundant routes using a dynamic approach. Should we use BGP internal utilizing the connections between the routers? Should we use HSRP on the routers? How best to get the routes to the N5K and should we be considering this?
View 5 Replies
View Related
Dec 23, 2011
I have my RV042 set up in Dual WAN mode and both WANs are working properly. I would like to configure WAN1 to handle all traffic, unless it fails and then have everything to go to WAN2. Pretty much what Smart Link Backup does, however with that enabled only 1 of the WANs is live at any given time. I'd like both WANs to always be live as I'm going to see the second one as a back-door into the network. Is this possible to do with routing? I tried setting a routing rule to have everything to go WAN1, but when WAN1 goes down, nothing is rounted via WAN2.
View 0 Replies
View Related
Sep 19, 2012
I have an RV042 (it's old, silver/dark grey plastic front one) w/ firmware 1.3.13.02-tm.
The reason we bought this (long ago) was to balance two WAN connections, one with unlimited data and one capped monthly. It did that once, but for a couple years both connections have been unmetered so it's just been balancing them 50/50. As of today one WAN connection (the new much faster one) is back to being metered but I can't figure out how to configure the RV042 as it once was to prefer sending traffic over the slow, unmetered connection first, and only use the faster metered connection when necessary.
It's been a long time and honestly I only vaguely remember the ability to prioritize a connection based on % of bandwidth used so that all traffic would go over the unlimited connection 1st until it was flooded, and only then fall over to the metered connection. This is totally different than the weighted round robin, or smart link backup.
I found this 3rdparty forum post that supports that vauge memory and suggests this was eliminated between firmware 1.23 and 1.3: [URL] Is it possible to replicate this functionality with the current firmware? if so how? If not, how to do roll back to firmware 1.23?
It sounded like perhaps I could assigned WAN1 a bandwidth of 100000 (even though it's really 1500) and then assign WAN2 a bandwidth of 1 (even though it's really 20000) and the result might be the prioritization I'm looking to achieve... but I feel like I'm stumbling in the dark at the point.
View 1 Replies
View Related
Jun 12, 2012
RV082 configured for Dual WAN [Code]....
(2) identical DSL connections, configured as Static IP (not PPPoE) with modems in bridged mode. Static IP's are /25 subnet and same gateway ** this may be a problem? Dual WAN set for Load Balance, network service detection is OFF
We have a 2003 terminal server running and successfully receiving connections through both WAN connections. Depending on location, half the users are connecting to WAN1 IP and the other half to WAN2 IP. We are getting sporadic disconnects of the remote users when they are idle for a couple minutes and automatic reconnection of the session takes over a minute. If they close the (locked up) session and reconnect manually it will let them in right away.
Could the handling of the Dual-WAN be the culprit? Could the same gateway for both WAN's create this issue upstream (out of my control)?I am going to move everyone to connecting through WAN1 and then change to Smart Link Backup and see if the issues persist.
Another thought is to use a secondary IP on the terminal server and use Protocol Binding to match "All traffic" for IP1 to WAN1 and IP2 to WAN2, which theoretically would stabilize the situation?
View 36 Replies
View Related
Jul 25, 2011
First of all i have gateway 2 gateway VPN configuration (both same RV042 with same firmware) + QVNP clients
The first one that i have those lines in my log "Ignoring Vendor ID payload" which doesn't allow clients to be connected from the first time they connect after several retries, or can't connect at all. I've doublechecked ports opened, and 500 is blocked by ISP. Also double checked, tried turning on and of Windows machine firewalls and etc - nothing worked. What would be the solution? should i manage to call my ISP and ask opening the port and it will solve my problem? HTTPS is enabled on router (this one i read in other topic)
The other problem is that one of my routers just stuck and i have manually to turn off, and then to turn on that it would start working as it was. Log files doesn't show anything. Router started to crash after the last Firmware upgrade.
View 1 Replies
View Related
Oct 24, 2011
I'm a bit new at this and I wanted to know if this is possible with the RV042 or if there's a better product to use. Our server is at located at location A and locations B and C telnet to the server via a VPN. We're looking at getting another ISP at each location as a backup and abandon older modem backups.
Would I setup a VPN tunnel between (A and B) and (A and C) for each ISP? Also I had a question on local IP addresses and if this would work
location A, ISP 1 -> location B, ISP1
local IP 192.168.1.1 remote IP 192.168.2.1
Public IP aa.aa.aa.aa Public IP bb.bb.bb.bb
[ code]....
View 2 Replies
View Related
Feb 19, 2012
I would like to make a design with 4 Nexus 5596UP. 2 of them equipped with Layer 3 Expansion Module so they can serve as core layer and the other 2 Nexus used as Layer 2 for aggregation server layer.The 2 Nexus in the core layer will run HSRP and will peer with ISP via BGP for Internet connection The 2 Nexus in the aggregation layer will be configured as layer 2 device and have FEX and switches connected to them.What I am ensure of is how the vpc and port-channel configuration should look like between the 4 nexus. What I was thinking is to run vpc between the 2 Nexus in the aggregation layer and between the 2 Nexus in the core layer. Than I was thinking of connecting each Nexus in the aggragtion layer to both Nexus in the core layer using port-channel and vice-versa.
View 3 Replies
View Related
Dec 17, 2012
how to change our wireless setup. Currently, we have 2 Cisco AiroNet 1130 WAP's in the office that go directly into the 2 POE ports on our Cisco ASA 5500. These WAP's have 1 SSID and are using WEP for security. After demonstrating the flaws of WEP to my boss, he has agreed that we should use something more secure and I've suggested WPA. We want visitors to our office to be able to hop on our wireless but on a separate guest SSID with WEP.
I'd like the internal SSID to route to the ASA and take the default route to the internet (it will be our new fiber connection once it's installed in a couple weeks). The default route is whichever connection is working since our ASA 5500 will fail over when it detects an outage.
I'd like the guest SSID to route to the ASA and then go over our existing cable connection. This connection will be our backup once the fiber connection is installed. Since we won't be using it very often, but will be paying for it, I advised that we send all guest wireless traffic over this connection since 50/5 is plenty for guests.
The current SSID (which will be the internal SSID) has no VLAN. We do currently have a few VLANS on our network, one for voice (.42) and one for data (.100) and the default (.0). What device to I create the VLAN on (Cisco 5500?) and how to I setup the WAP? I need very basic instructions to start and I'm also trying to do this without causing downtime if possible.
I've attached a diagram of what it should look like. Red indicates our internal network and Blue indicates the guest network. I can send screenshots as well.
View 2 Replies
View Related
May 20, 2007
Having a problem everytime I try to use load balance on my Rv042 it is slow as a dog and sometimes wont connect at all. if I run in smart backup mode its fine. removed firewall rebooted everything tried numerous configerations upgraded to the latest frimware just about to be convinced
View 2 Replies
View Related
Mar 30, 2012
The basic setup Newly installed redundant ISP, thus setting up the 891 with dual WAN Using PFR to load balance between the two. Did initial config through CCP (not express), but I am familiar with the basics of IOS CLI (not used to the new zone based firewall yet, managed aour old Pix for too long, but that is a different subject)
I cannot seem to get anything but Gi0 to be accepted as a WAN interface. I go through the entire setup in CCP, test each connection, etc, and it all looks good until I exit out of CCP and go back in. At that point, I get squat out of Fa8. CCP won't let me test the connection, won't let me edit the connection, wont let me delete the connection. The wizard for a new WAN connection becomes available again (Wanting to set up a "second" WAN on Fa7...)
Again, I have verified connections to each ISP line independently, either one works just fine on Gi0, neither ever works on Fa8. This is my first real foray into PfR.
Building configuration...
Current configuration : 21486 bytes
Last configuration change at 18:59:43 UTC Mon Mar 26 2012 by admin
[URL]....
View 4 Replies
View Related
Apr 18, 2012
What I currently have is a Cisco 891W Router as well as two ISP's (both with dynamic IP's) in. I'm currently just running one of my modems into the 891 through the FE8 port and then if for some reason I have an internet failure switching the ISP modems. What I'm wondering is if there is a fairly simple way to configure (and attach) both modems to this router and then set it up to handle this failover automatically?
View 1 Replies
View Related
Nov 13, 2011
I'm trying to configure cisco 1811 with dual isp internet connections. Everything is working fine till i get to setting up port forwards.The port forwards for 2nd ISP do not work while connection to 1st isp is active. If if shutdown the connection to isp1 the port forwards work fine.
here's relevant section of the config
Code:
track 123 ip sla 1 reachability
delay down 15 up 10
!
track 456 ip sla 2 reachability
delay down 15 up 10
[code]....
I can access the 192.168.2.131 web server using the ISP1 ip but not ISP2 ip If i shutdown ISP1 interface the server becomes accessible through ISP2.Also while ISP1 is active I can't remote desktop to 192.168.1.210There are no acls, firewall zones or anything else.
View 3 Replies
View Related
Jul 13, 2011
I have existing Sonic FW in my company we are moving from sonic FW to ASA 5510 Security plus lice. I have two ISP currently connected to sonic Firewall I am planning to implement Dual ISP configuration on ASA5510.
View 12 Replies
View Related
Jan 31, 2012
I've a RV082 with 2 internet connections.The idea is to permit external connections to my server and if one Internet line falls, automatically switch to the other.
We have configured the router in Smart Link backup.We try to connect with WAN1 and WAN2 enabled and all works fine.
We try to connect with WAN1 disabled and automatically WAN2 is activated.The problem start here...if WAN1 is activated while there are connections using WAN2, these connections falls!
How I must configure the router to permit that active connections are not disconnected from WAN2 even when WAN1 connection come back?
View 1 Replies
View Related
Dec 6, 2012
I recently configured WCCP with a Sophos Web Filter on my network it works good but the problem I am having is I have two 5520s so I am directing the device to look at 2 different IP addresses and since the devices are in an Active/Passive failover. The problem is because the second device is in a passive failover it is not responding which is throwing connection errors to my Sophos device. I know you can have a single management connection for the ASA's but is there a way to have a single IP for the ASAs for the WCCP?
View 1 Replies
View Related
Oct 15, 2012
I have recently implimented an RV016 device into our network. We have a bonded T1 service with Paetec/Windstream (5 static IPs) and also a cable connection with Comcast (no static IP). The T1 has been our primary connection, and our MX and A records all use this IP address. I have the rules set and using a one-to-one NAT setup with our 5 IPs. Everything is working great with the T1 in place and email is flowing with no problems, however when I connect the cable into the WAN2 port and try to send email, its using that outbound connection, rather then the T1 and our spam filter is blocking it. So the email is rejected and we get this message below.
---------------------------------------------------------------------------
Delivery has failed to these recipients or groups:
xxxx@gmail.com (xxxx@gmail.com)Your message wasn't delivered due to a permission or security issue. It may have been rejected by a moderator, the address may only accept e-mail from certain senders, or another restriction may be preventing delivery.
The following organization rejected your message: (our smtp spam relay)
-------------------------------------------------------------------------
The reason for being rejected is just because it doesn't recongnize the IP address/gateway it is coming from.
My question is, how do I define that all email is sent out through our T1 connections IP address in the router?I see options for Advanced Routing or Bandwidth Management, but not sure what one I need to configure as I am not too familiar with these settings. I have Intelligent Balancer(Auto Mode) enabled as well by default.
The reason for adding the second internet connection is strictly for load balencing and getting some more bandwidth in our location.
View 3 Replies
View Related
Oct 16, 2012
I have recently implimented an RV016 device into our network. We have a bonded T1 service with Paetec/Windstream (5 static IPs) and also a cable connection with Comcast (no static IP). The T1 has been our primary connection, and our MX and A records all use this IP address. I have the rules set and using a one-to-one NAT setup with our 5 IPs. Everything is working great with the T1 in place and email is flowing with no problems, however when I connect the cable into the WAN2 port and try to send email, its using that outbound connection, rather then the T1 and our spam filter is blocking it. So the email is rejected and we get this message below.
View 1 Replies
View Related
Dec 9, 2011
Will 2811 Router with 4 switch port module, How to do dual ISP configuration on this router.
View 10 Replies
View Related
Mar 6, 2007
In the LAN network 4507R as core switch configured with several vlans.One vlan connects to the dual homed routers which in turn connecting to the single isp. I need to configure the HSRP for the internal vlans and the same time to use the load balancing or failover using the dual homed routers to the isp.
View 7 Replies
View Related
Jun 24, 2012
In IOS verson 12.X there was a Bidirectional Forwarding Detection configuration however in IOS 15.0 this isn't available at least not with the same syntax. Is this feature not available in 15.0?
In 12.X this was the syntax of the command:switch virtual domain <number>.
View 1 Replies
View Related
Feb 8, 2013
Region : UnitedStates
Model : TL-WDR3600
Hardware Version : V1
Firmware Version :
ISP :
I recently bought wdr3600 and just trying to configure bridge through WDS configuration. I just enabled WDS and picked my initial wireless router after clicking the Survey button, then save it. After the reboot, I cant seem to ping/access 192.168.0.1 and the wireless SSID cant be seen any longer. I tried doing the reset button for 30secs but looks like nothing is working and not resetting. And I am still getting 169.254.x.x
View 5 Replies
View Related
Apr 4, 2013
Region : Australia
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23 Build 121225 Rel.37950n
ISP : Optusnet
I've had a recent problem where I turn off my router computer etc every night and the next day the router has reset to original configuration. I lose SSID, password, region etc and have to do a quick setup or restore a back up config each time.
I've had the unit for about 1 1/2 months and all was ok until recently when I switch the wireless switch at the back of the unit so my kids couldn't access the router and internet. I switched it back on after a while and all was ok and later shut down for the night. The next day when I turned it all on again the SSID password etc had reset.
Anyhow I contacted TP-link and was told to disable the WPS for both 2.4Ghz and 5Ghz. That seemed to fix the problem for a couple of days but it has now returned.Should I try the 30/30/30 reset??
View 1 Replies
View Related
Feb 13, 2013
Region : UnitedKingdom
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP :
After setting up the newly arrived router, renaming the SSID and changing password for 2.4 GHZ AND 5 GHZ and also renaming the default router username and password, I decided to update the firmware.The procedure wiped all configuration I've made forcing me to do all over again.
View 3 Replies
View Related
Feb 24, 2013
I have a two fiber connection from our Central Office(6513) to Remote office (6509). I have a requirement that on the remote office if one of the fiber goes down, the second fiber should work as a failover. I am planning to use SUP720-3B SFP to connect to the CO.
Can I connet one fiber to Sup720-3b G5/1 & another fiber connection to G5/2? or Can I connet one fiber to Sup720-3b G5/1 & another fiber connection to G6/2? I am running EIGRP between sites. Any sample config.
sup-bootflash:s72033-pk9sv-mz.122-18.SXD7b.bin"
View 4 Replies
View Related
Dec 24, 2012
We have two internet connections with 2mbps each. I would like to go for Wireless Dual WAN Router. know the +ve and -ve of this usage. know the best modals. We have 30 macs in my company.
View 3 Replies
View Related
Mar 10, 2011
I', trying to open my ports 80 and 37777 and have successfully opened them on my linksys router but behind that I have an at&t modem/router....My questions is how do I find the URL number to access my second router to open the ports on it also?
View 3 Replies
View Related
Nov 1, 2011
I have 5 cisco 1812 routers that i set up in a hub-spoke dmvpn configuration between 5 sites. All routers have a secondary internet connection . Could i set up a second tunnel interface on each router to create a backup dmvpn that will use this secondary internet connection? i use EIGRP for routing.
View 2 Replies
View Related
Jun 5, 2013
We are connecting to a Cisco DPC3825 cable modem supplied by our ISP. It has been configured to act as a switch only. They have supplied us with 2 static IP addresses.
When each WAN port is connected individually, everything is fine. I see the IP addresses on the respective WAN port, and it is working fine.
When I connect both WAN ports to the modem at the same time, I see a large amount of traffic between the WAN ports, as indicated by the port LEDs, and the RV042G becomes completely non-responsive through its web interface.
How do I get the RV042G working with both WAN ports connected?
View 3 Replies
View Related
