Cisco Routers :: RV042 Dual Wan For Sip Trunk?
Dec 10, 2012
2 router to connect my phone system to a Sip trunk provider router and to extend my Lan segments so the phone system have internet access.i need it this way because i cant put 2 default gateway in my phone system so the cisco Rv042 is the default gateway of the phone system and i use port fowarding of the UDP ports 5060 to point to the system.and i also use protocol binding of these ports to the Wan 1
Phone system connect to a switchport The sip trunk router connect to the Wan 1 My lan is connected to the Wan 2 Everything is working fine exept this intermittent issue : Each hour or so my sip trunk stop working. to make it start working i need to unplug my Wan 2 connection and wait for 1 minute.
View 4 Replies
ADVERTISEMENT
Feb 21, 2013
I run 2 RV042 V1 for home and office with Gateway to Gateway VPN connection with single WAN connection in use. Everything works like a charm!
I was even able to create VPN connection with 2 WAN connection on one Router and 1 WAN connection on another with Smart link failover and VPN Tunel Backup.
I got problem though when i tried more complex connection diagram. [URL]
So basically I now have 2 ISP connections on each point with Static IPs and I'd like VPN Connection to be alive for ALL 4 options automatically with failovers (smart links) And tunel backups but i'm not sure if that's ever possible with my equipment.
View 2 Replies
View Related
Aug 19, 2011
I need configuring Cisco RV042 dual wlan and port forwarding for 2 servers web and dns in LAN
View 1 Replies
View Related
Jan 7, 2013
I'm in the process of finding a dual WAN router with VPN support, that allow me to redirect some traffic to one specific WAN port and do load balancing of that specific traffic in case of that WAN failing (this last requirement is preferably but isn't fully needed).
Does the RV042/G could work with that? In that case, does it allow protocol redirect only? What about ip/ports redirecting? Or some kind of packet filtering to redirect to specific WAN ports?
View 6 Replies
View Related
Apr 22, 2013
Cisco RV042 Dual WAN VPN Router -how to configure dynamic DNS without having to use the pre-programmed DDNS companies that are populated by default if my DDNS company is not listed and you cannot manually enter another company that is not on the list?
View 1 Replies
View Related
Dec 23, 2011
I have my RV042 set up in Dual WAN mode and both WANs are working properly. I would like to configure WAN1 to handle all traffic, unless it fails and then have everything to go to WAN2. Pretty much what Smart Link Backup does, however with that enabled only 1 of the WANs is live at any given time. I'd like both WANs to always be live as I'm going to see the second one as a back-door into the network. Is this possible to do with routing? I tried setting a routing rule to have everything to go WAN1, but when WAN1 goes down, nothing is rounted via WAN2.
View 0 Replies
View Related
Sep 19, 2012
I have an RV042 (it's old, silver/dark grey plastic front one) w/ firmware 1.3.13.02-tm.
The reason we bought this (long ago) was to balance two WAN connections, one with unlimited data and one capped monthly. It did that once, but for a couple years both connections have been unmetered so it's just been balancing them 50/50. As of today one WAN connection (the new much faster one) is back to being metered but I can't figure out how to configure the RV042 as it once was to prefer sending traffic over the slow, unmetered connection first, and only use the faster metered connection when necessary.
It's been a long time and honestly I only vaguely remember the ability to prioritize a connection based on % of bandwidth used so that all traffic would go over the unlimited connection 1st until it was flooded, and only then fall over to the metered connection. This is totally different than the weighted round robin, or smart link backup.
I found this 3rdparty forum post that supports that vauge memory and suggests this was eliminated between firmware 1.23 and 1.3: [URL] Is it possible to replicate this functionality with the current firmware? if so how? If not, how to do roll back to firmware 1.23?
It sounded like perhaps I could assigned WAN1 a bandwidth of 100000 (even though it's really 1500) and then assign WAN2 a bandwidth of 1 (even though it's really 20000) and the result might be the prioritization I'm looking to achieve... but I feel like I'm stumbling in the dark at the point.
View 1 Replies
View Related
Jul 25, 2011
First of all i have gateway 2 gateway VPN configuration (both same RV042 with same firmware) + QVNP clients
The first one that i have those lines in my log "Ignoring Vendor ID payload" which doesn't allow clients to be connected from the first time they connect after several retries, or can't connect at all. I've doublechecked ports opened, and 500 is blocked by ISP. Also double checked, tried turning on and of Windows machine firewalls and etc - nothing worked. What would be the solution? should i manage to call my ISP and ask opening the port and it will solve my problem? HTTPS is enabled on router (this one i read in other topic)
The other problem is that one of my routers just stuck and i have manually to turn off, and then to turn on that it would start working as it was. Log files doesn't show anything. Router started to crash after the last Firmware upgrade.
View 1 Replies
View Related
Oct 24, 2011
I'm a bit new at this and I wanted to know if this is possible with the RV042 or if there's a better product to use. Our server is at located at location A and locations B and C telnet to the server via a VPN. We're looking at getting another ISP at each location as a backup and abandon older modem backups.
Would I setup a VPN tunnel between (A and B) and (A and C) for each ISP? Also I had a question on local IP addresses and if this would work
location A, ISP 1 -> location B, ISP1
local IP 192.168.1.1 remote IP 192.168.2.1
Public IP aa.aa.aa.aa Public IP bb.bb.bb.bb
[ code]....
View 2 Replies
View Related
Mar 29, 2012
I wanted to ask a question about the diagram I have included. We are bringing up 2 MPLS WAN connections and would like some specifics on the best design. We are using BGP to the providers. From there we have big questions. We can run BGP internal and are licensed to do so on the N5K's. The N5Ks are currently using HSRP for inside LAN clients as default gateway. We want to load balance and provide redundant routes using a dynamic approach. Should we use BGP internal utilizing the connections between the routers? Should we use HSRP on the routers? How best to get the routes to the N5K and should we be considering this?
View 5 Replies
View Related
May 20, 2007
Having a problem everytime I try to use load balance on my Rv042 it is slow as a dog and sometimes wont connect at all. if I run in smart backup mode its fine. removed firewall rebooted everything tried numerous configerations upgraded to the latest frimware just about to be convinced
View 2 Replies
View Related
Apr 11, 2013
Is there really any reason why you wouldn't use spanning-tree portfast on a trunk port other than a trunk between two switches? We have it enabled on all ports except for the fiber trunk between two non-stacked switches and the trunk ports connected to our Astaro firewall.I'd like to enable it on the ports to the firewall unless that would cause issues.
View 9 Replies
View Related
Feb 12, 2012
we recently aquired a managed services job and have to do a overhaul of the vlan configs and have a whole dozen WC2948G's trunk between a set of ports as well as trunk out a LAG channel setup to non cisco equipment. the deal is the lacp-channel works properly on both ends but no routing of vlans between ports and between the lag trunk are working.
theres alot of settings in the config and im planning on clearing it and starting from scratch but before i do i want to know where my problem lies.
[code]...
View 6 Replies
View Related
Jun 26, 2012
trunk port connecting but not allowing access to tree; i connected 4506 port to 3550 port; and i set both to switchport mode dynamic desirable; the 4506 port was set with switchport mode access and switchport mode access vlan ?; i used the command default switchport access vlan to remove the vlan; the ports are up but as I stated I cannot connect ot our workgroup tree
View 4 Replies
View Related
Jan 24, 2013
I have RV042 and E4200 routers . I tried the manual UPnP port forwarding using Rv042 router and was succesful ( by typing 192.168.1.1 in the explorer and logged in using user name and password )
I am using a linux embedded system whose Internal IP ,Internal port are mapped .This system is connected to one of the LAN ports
I want to try auto UPnP port forwarding both for RV042 router and Linksys E4200 routers
After enabling the Upnp option only and logging out ,Can i add a port mapping entry in this router without logging in using a C++ program which runs on linux embedded system .
View 2 Replies
View Related
Aug 22, 2012
I was looking for a small business router that has VPN support and dual WAN support for load balancing. Upon reading reviews, I think RV042/RV042G is a good choice. Now am thinking if it supports intervlan/ router-on-a-stick configuration?
View 5 Replies
View Related
May 30, 2012
I bought an rv120w. Now i want to trunk 2 lan ports to an smart switch to get 200MB out of that link.
The trunk mode in there in the manual that came in the cd with the unit i bought but is not in the web console.
I have updated the IOS to 1.0.3.10 to see if th trunk mode was there but is not.
My question is,
1 is that trunking feature there in the ios?
2- If not, why is listed in hte manual that came with the unit?
3- if it is in the ios, is there a was to by pass the web console and configure this?
4- can i do i maybe backing up the config then, editing the file and restoring it?
Screenshot below is from the manual in hte cd that came with the router
View 2 Replies
View Related
Feb 27, 2012
I have two Internet connections-
1-DSL Modem (WAN1-Internet Port)
2-Cable Modem-Comcast (WAN2-DMZ/Internet Port)
I connected the DSL (WAN1-Internet) port in and the Cisco RV042 was able to get an IP automatically. I tested the connection and it works just fine. Then I connect the Cable Modem-Comcast (WAN2-DMZ/Internet Port) in and I have the RV042 automatically optain IP address. But it just says 0.0.0.0. I've tried release/renew and that does nothing. Also, when I connect the 2nd Internet connection the Internet goes down. The only way it goes back up is when I disable under the PORT MANAGMENT setting.
All the settings have been kept to the default.How can I get the router to obtain an IP address from the Cable Modem-Comcast (WAN2 DMZ/Internet Port).
View 5 Replies
View Related
Mar 6, 2012
We have an Cisco RV042. We need to setup a VPN with a business partner who is already using our current IP scheme on another VPN with another client. They have asked us to NAT our IP's from 192.168.25.x to 192.168.245.x
I can't seem to figure this out on this router. I have done it on a Sonicwall and Watchguard, but can't seem to get it to work on the RV042.
I have setup the VPN and the One-To-One NAT. The tunnel will connect (using the 245.x IP as our local IP on the VPN setup), but no traffic will pass through.
View 1 Replies
View Related
May 20, 2012
i was planed to make a vpn over rv042 so i get the rv042 connected behind a thosmon 456(configured as a bridge) and 1 static ip ... and i configured the vpn and worked great ...but due to some circumstance i get a package of 6 ips insted of the old ip , so when i try to configure the router with the ISP they but the wan ip 10.232.x.x and told me that an internal ip from there lan ... and give me the 6 ip of 196.x.x.x to use as 1 for internal interface for the rv042 and 5 for the pc's,now the vpn not working anymore...notice: when try to configure the vpn tunnle in the local securty setting i mark the ip only and the ip that abear is the wan ip 10.232.x.x but i can't ping that ip beside i can ping the internal ip of the router 196.x.x.50does rv042 can support static and virtual ip inside the lan |! can i configure the thomson as pppoe and use one static ip from 196.x.x.x as wan ip for it ... and use anther 196.x.x.x ip for the rv042 to get access from outside and connect the lan to the rv042 with internal ip 192.168.x.x ...so i can access the vpn from outside .....and can connect the device i need to use static ip to the thomson ...
View 0 Replies
View Related
Sep 23, 2011
Firmware v4.0.4.02 has a nasty bug in the VPN section. If you switch to "IP by DNS Resolved" (yes, it says "Resolved" instead of "Resolution". Gotta love all the Engrish in the RV042!), it will automatically populate the field with "@yourdomain.com". This will cause the VPN to not lookup the proper IP address. Simply deleting the atmark after it populates will fix the problem.
Let's see what happens when we validate a Cisco RV042 webpage:
Errors found while checking this document as HTML 4.01 Transitional!
Result: 353 Errors, 1 warning(s)
Don't even get me started on the horrible Javascript...
View 0 Replies
View Related
Apr 24, 2013
i am trying to make a simple Site to SiteVPN between two offices, one has Cisco ASA and one has RV042 router.when traffic initiated from ASA side, i keep getting this message in Debug and tunnel wont come up
.
[IKEv1]: Group = A.A.A.139, IP = A.A.A.139, Queuing KEY-ACQUIRE messages to be processed when P1 SA is complete.Apr 26 00:15:53 [IKEv1 DEBUG]: Pitcher: received a key acquire message, spi 0x0
whereas if traffic initiated from RV042 side, i keep getting this message in debug and tunnel wont come up.
Apr 26 00:43:44 [IKEv1 DEBUG]: IP = RV.RV.RV.139, Oakley proposal is acceptableApr 26 00:43:44 [IKEv1 DEBUG]: IP = RV.RV.RV.139, IKE SA Proposal # 1, Transform # 0 acceptable Matches global IKE entry # 6Apr 26 00:43:44 [IKEv1]: IP = RV.RV.RV.139, Connection landed on tunnel_group RV.RV.RV.139Apr 26 00:43:45 [IKEv1]: IP = RV.RV.RV.139, Connection landed on tunnel_group RV.RV.RV.139Apr 26 00:43:45 [IKEv1]: Group = RV.RV.RV.139, IP = RV.RV.RV.139, Freeing previously allocated memory for authorization-dn-attributesApr 26 00:43:45 [IKEv1]: Group = RV.RV.RV.139, IP = RV.RV.RV.139, PHASE 1 COMPLETEDApr 26 00:43:45 [IKEv1]: IP =RV.RV.RV.139, Keep-alive type for this connection: DPDApr 26 00:43:45 [IKEv1 DEBUG]: Group =
[code].....
View 1 Replies
View Related
Sep 27, 2012
Apparently one of my two ISPs,CenturyLink, supports 6rd connections to IPv6.
This is supported natively on my Q1000 ActionTec modem, however my modem is in "transparent bridging" mode, so that the RV042 v3 can be the only router.
how to configure the RV042 to operate in this manner.
Per the CenturyLink FAQ: the IPv6 address space is:
2602::0 /24
Most importantly, can I do this WITHOUT buying a new modem.
View 2 Replies
View Related
Aug 28, 2011
I have a RV042 router (Ser#: NKS10462300, HW V3) running Firmware version v4.0.2.08-tm (Jan 14 2011 22:08:38) set up as a gateway. Right after it boots I am able to long into its web interface but shortly after that if I try to log into it I go through a very log time out while the web page is waiting the router to respond and then eventually IE comes back and says it 'cannot display the web [age'.
View 30 Replies
View Related
Jan 14, 2013
I have a Cisco RV042 VPN Router and I have added a group vpn, but when I am trying to connect I got an error that the remote vpn server isn't responding.
Here's my log:
2013/01/15 12:24:53 [STATUS]OS Version: Windows 7
2013/01/15 12:24:53 [STATUS]Windows Firewall Domain Profile Settings: ON
2013/01/15 12:24:53 [STATUS]Windows Firewall Private Profile Settings: OFF
2013/01/15 12:24:53 [STATUS]Windows Firewall Private Profile Settings: OFF
2013/01/15 12:24:53 [STATUS]One network interface detected with IP address MY HOME IP
[code]....
If I am trying to connect the status of the vpn user in the remote interface is "online".I have deactived my firewall at home and at the server for testing purposes.
View 2 Replies
View Related
Apr 19, 2012
I am looking to configure RV042 for VPN access to local machines and Win 2008 server. The story: Had issues with remote printers being created for clients logging into old Linksys RV042 with Linksys VPN software. First Tech exposed server without security, and it had to be removed as it was being attacked, but did not fix printing issue. 2nd tech could not get VPN to work after 1st tech. 3rd tech, 4hours, and I got that the router is a piece of ... So I'm out over 1000, and not able to have a simple router set up. The present situation. New RV042 with firmware V4.1.1.01, using Cisco VPN client 5.0.07.0410, most XP 32 bit machines coming into network, one 64 bit win 7. My clients have been unable to access their data for too long.
View 3 Replies
View Related
Feb 6, 2012
Is there any documentation out there on a step-by-step instructions on setting up a vpn on a RV042 router?
View 1 Replies
View Related
Apr 30, 2012
I'm trying to set up 2 subnet with two RV042 routers. One router will act as a gateway and both WAN ports will be used by two different isp connection. The first router (gateway) LAN IP will be 192.168.0.1/24. I would also like to set up another router behind the gateway with with separate subnet 192.168.1.X/24. And I would like clients on the 192.168.1.x subnet to use the internet through the gateway router and clients on the 192.168.0.x subnet to access resources on the 192.168.1.x subnet. Am I able to do this with two RV042?
View 6 Replies
View Related
Sep 2, 2012
The issue is when I am using PPTP the router seems to die, not every time but I would say about once a week now. I am the only PPTP user, simply using RDP. A few hours into an RDP session the PPTP connection drops and cannot be re-established, or quickvpn, nothing. Routing still works (somewhat, high latency) locally.
When I've checked the logs both times I see:
TimeEvent-TypeMessageSep 3 17:07:56 2012KernelOut of memory: Killed process 14354 (pppd). Sep 3 17:07:56 2012KernelOut of Memory: Kill process 14354 (pppd) score 177 and children. Sep 3 17:07:56 2012KernelOut of memory: Killed process 14367 (sh). Sep 3 17:07:56 2012KernelOut of Memory: Kill process 14354 (pppd) score 234 and children. Sep 3 16:46:41 2012KernelOut of memory: Killed process 14330 (pppd). Sep 3 16:46:41 2012KernelOut of Memory: Kill process 14329 (pptpctrl) score 134 and children. Sep 3 16:46:41 2012KernelOut of memory: Killed process 14324 (pppd). Sep 3 16:46:41 2012KernelOut of Memory: Kill process 14324 (pppd) score 177 and children. Sep 3 16:46:40 2012KernelOut of memory: Killed process 14328 (sh). Sep 3 16:46:40 2012KernelOut of Memory: Kill process 14324 (pppd) score 234 and children. Sep 3 15:36:15 2012KernelOut of memory: Killed process 14187 (pppd). Sep 3
[code]....
View 3 Replies
View Related
Nov 11, 2012
I have an RV042 connected via VPN to the office (to a LinkSys DFL-700). Sometimes the VPN is dropped and never activates again. In this state, if I try to connect to the WEB interface, I can log in, but the router hangs at the login screen. I have to power recycle the router to make it work again.
Updated to latest firmware 4.2.1.02 for V3 hardware. The funny thing is that services from the WEB routed through to local IP adresses on the lan is still accessible. I have setup PPPT VPN on the router, and that also fails to work.
Is there, as a workaround, any possibility to access the routers reset page or access via TELNET to reset the router? This migth be useful, when I'm out. (I have a backup solution to access the local network at home).
View 3 Replies
View Related
Jun 29, 2012
I have just purchased the RV042 and while it is working great on WAN1 over Xfinity/Comcast broadband, I'm unable to get it working with my AT&T DSL for WAN2. I am planning on running this in failover mode - not load balancing.
The DSL modem it is connected to is a SpeedStream (hooking up laptop directly works etc. etc.). The SpeedStream is set to PPOE authentication passed in via the computer (in this case the RV042). On the RV042 side, I set it to use PPOE, using the credentials as given my AT&T DSL. The DNS servers are set to the ones recommended
View 4 Replies
View Related
Dec 24, 2012
We have two internet connections with 2mbps each. I would like to go for Wireless Dual WAN Router. know the +ve and -ve of this usage. know the best modals. We have 30 macs in my company.
View 3 Replies
View Related
Jul 18, 2012
Are the RV042 and RV082 routers SIP AWARE?I haven't had any luck finding documentation stating such.
View 2 Replies
View Related
