Cisco Routers :: RV042 And AT&T DSL Configuration
Jun 29, 2012
I have just purchased the RV042 and while it is working great on WAN1 over Xfinity/Comcast broadband, I'm unable to get it working with my AT&T DSL for WAN2. I am planning on running this in failover mode - not load balancing.
The DSL modem it is connected to is a SpeedStream (hooking up laptop directly works etc. etc.). The SpeedStream is set to PPOE authentication passed in via the computer (in this case the RV042). On the RV042 side, I set it to use PPOE, using the credentials as given my AT&T DSL. The DNS servers are set to the ones recommended
View 4 Replies
ADVERTISEMENT
May 20, 2012
i was planed to make a vpn over rv042 so i get the rv042 connected behind a thosmon 456(configured as a bridge) and 1 static ip ... and i configured the vpn and worked great ...but due to some circumstance i get a package of 6 ips insted of the old ip , so when i try to configure the router with the ISP they but the wan ip 10.232.x.x and told me that an internal ip from there lan ... and give me the 6 ip of 196.x.x.x to use as 1 for internal interface for the rv042 and 5 for the pc's,now the vpn not working anymore...notice: when try to configure the vpn tunnle in the local securty setting i mark the ip only and the ip that abear is the wan ip 10.232.x.x but i can't ping that ip beside i can ping the internal ip of the router 196.x.x.50does rv042 can support static and virtual ip inside the lan |! can i configure the thomson as pppoe and use one static ip from 196.x.x.x as wan ip for it ... and use anther 196.x.x.x ip for the rv042 to get access from outside and connect the lan to the rv042 with internal ip 192.168.x.x ...so i can access the vpn from outside .....and can connect the device i need to use static ip to the thomson ...
View 0 Replies
View Related
Apr 19, 2012
I am looking to configure RV042 for VPN access to local machines and Win 2008 server. The story: Had issues with remote printers being created for clients logging into old Linksys RV042 with Linksys VPN software. First Tech exposed server without security, and it had to be removed as it was being attacked, but did not fix printing issue. 2nd tech could not get VPN to work after 1st tech. 3rd tech, 4hours, and I got that the router is a piece of ... So I'm out over 1000, and not able to have a simple router set up. The present situation. New RV042 with firmware V4.1.1.01, using Cisco VPN client 5.0.07.0410, most XP 32 bit machines coming into network, one 64 bit win 7. My clients have been unable to access their data for too long.
View 3 Replies
View Related
Oct 25, 2012
Yesterday I have purchased a new rv042 router, If i enter url...I have access to a menu but nothing is shown when I follow the menu link.
View 6 Replies
View Related
May 15, 2013
I am not having much success setting up a IPSec VPN tunnel between a RV042 V3 running v4.0.0.07 firmware and PIX 525 running 8.0(4) code.
Let's say the configuration looks like this:
The RV042 has public IP 70.0.0.1 and private LAN IP 192.168.1.1 /24 The PIX has outside IP 69.0.0.1 and inside LAN IP 172.16.0.1 /24 The RV042 is running as DHCP server on it's private LAN A Windows server at 172.16.0.2 is the DHCP server on the PIX's inside LAN.
I've tried every option on the RV042 for Phase 1 and Phase 2, but I am not certain how to configure the Advanced features especially Aggressive Mode, Compress, Keep-Alive, AH Hash Algorithm and Dead Peer Detection.
On the PIX I've tried the basic setup through ADSM, but it's not as clear or obvious to configure both sides with compatible settings compared to setting up a tunnel between two RV042s.
View 1 Replies
View Related
Oct 1, 2012
I've been working on getting a client to Gateway configuration going for quite some time now. Had it working with a different Cisco single wan router that failed. The user replaced the router with an RV042 and we are trying to get the QuickVPN to once again connect to the router as it did before the replacement. Previously we did connect successfully with Windows 7 clients.
Router: RV042 v3 firmware 4.0.4.02-tm Quickvpn version 1.4.2.1
what i keep getting in the log is the following :
2012/10/02 12:55:07 [STATUS]OS Version: Windows Vista
2012/10/02 12:55:07 [STATUS]Windows Firewall Domain Profile Settings: ON
2012/10/02 12:55:07 [STATUS]Windows Firewall Private Profile Settings: ON
[Code].....
View 5 Replies
View Related
Apr 24, 2013
I Can't see the far video when run the video conference. the audio is working fine.How to config the port forwarding for video conference?
View 1 Replies
View Related
Apr 8, 2012
I wanna block the Lan IP address(eg:192.168.2.106) to visit wan web, and allow it to lan.How can i set it in access rules?
View 2 Replies
View Related
Nov 11, 2010
Any working configuration to connect the iPad VPN-client (IPSEC) to the RV042?
View 16 Replies
View Related
Apr 23, 2013
I have got two CISCO RV042 .I need to configure a site to site VPN .
View 1 Replies
View Related
Feb 21, 2013
I run 2 RV042 V1 for home and office with Gateway to Gateway VPN connection with single WAN connection in use. Everything works like a charm!
I was even able to create VPN connection with 2 WAN connection on one Router and 1 WAN connection on another with Smart link failover and VPN Tunel Backup.
I got problem though when i tried more complex connection diagram. [URL]
So basically I now have 2 ISP connections on each point with Static IPs and I'd like VPN Connection to be alive for ALL 4 options automatically with failovers (smart links) And tunel backups but i'm not sure if that's ever possible with my equipment.
View 2 Replies
View Related
Jan 24, 2013
I have RV042 and E4200 routers . I tried the manual UPnP port forwarding using Rv042 router and was succesful ( by typing 192.168.1.1 in the explorer and logged in using user name and password )
I am using a linux embedded system whose Internal IP ,Internal port are mapped .This system is connected to one of the LAN ports
I want to try auto UPnP port forwarding both for RV042 router and Linksys E4200 routers
After enabling the Upnp option only and logging out ,Can i add a port mapping entry in this router without logging in using a C++ program which runs on linux embedded system .
View 2 Replies
View Related
Aug 22, 2012
I was looking for a small business router that has VPN support and dual WAN support for load balancing. Upon reading reviews, I think RV042/RV042G is a good choice. Now am thinking if it supports intervlan/ router-on-a-stick configuration?
View 5 Replies
View Related
Mar 3, 2013
i am currently using 2 DSL WIFI modem and wants to combine them to my RV042 dual wan router but as i set them up using WAN1 and Wan2 as "Obtain IP Automatically" there is no internet connection?
View 2 Replies
View Related
Jan 14, 2011
Setup is two dynamic IP locations
1. first location RV042 is the gateway attached to ADSL modem
2. second location RV042 is behind BT home hub gateway - for now the BTHH DMZ is enabled to the RV042
Followed the user manual config for two dynamic IP but it seems that the RV042 behind the BTHH obviously has a different IP than the resolved IP and is causing problems with connection.
This from the log file:
Jan 14 15:04:16 2011 VPN Log Received Vendor ID payload Type = [Dead Peer Detection]
Jan 14 15:04:16 2011 VPN Log [Tunnel Negotiation Info] <<< Responder Received Aggressive Mode 1st packet
Jan 14 15:04:16 2011 VPN Log Aggressive mode peer ID is ID_IPV4_ADDR: '192.168.95.139'
Jan 14 15:04:16 2011 VPN Log No suitable connection for peer '192.168.95.139', Please check Phase 1 ID value
Jan 14 15:04:16 2011 VPN Log initial Aggressive Mode packet claiming to be from 81.156.xxx.xx on 81.156.xxx.xx
But no connection has been authorized,check peer ID Is there some way of making the RV042 behind the BTHH properly identifiable to the other end?
View 1 Replies
View Related
Feb 27, 2012
I have two Internet connections-
1-DSL Modem (WAN1-Internet Port)
2-Cable Modem-Comcast (WAN2-DMZ/Internet Port)
I connected the DSL (WAN1-Internet) port in and the Cisco RV042 was able to get an IP automatically. I tested the connection and it works just fine. Then I connect the Cable Modem-Comcast (WAN2-DMZ/Internet Port) in and I have the RV042 automatically optain IP address. But it just says 0.0.0.0. I've tried release/renew and that does nothing. Also, when I connect the 2nd Internet connection the Internet goes down. The only way it goes back up is when I disable under the PORT MANAGMENT setting.
All the settings have been kept to the default.How can I get the router to obtain an IP address from the Cable Modem-Comcast (WAN2 DMZ/Internet Port).
View 5 Replies
View Related
Mar 6, 2012
We have an Cisco RV042. We need to setup a VPN with a business partner who is already using our current IP scheme on another VPN with another client. They have asked us to NAT our IP's from 192.168.25.x to 192.168.245.x
I can't seem to figure this out on this router. I have done it on a Sonicwall and Watchguard, but can't seem to get it to work on the RV042.
I have setup the VPN and the One-To-One NAT. The tunnel will connect (using the 245.x IP as our local IP on the VPN setup), but no traffic will pass through.
View 1 Replies
View Related
Sep 23, 2011
Firmware v4.0.4.02 has a nasty bug in the VPN section. If you switch to "IP by DNS Resolved" (yes, it says "Resolved" instead of "Resolution". Gotta love all the Engrish in the RV042!), it will automatically populate the field with "@yourdomain.com". This will cause the VPN to not lookup the proper IP address. Simply deleting the atmark after it populates will fix the problem.
Let's see what happens when we validate a Cisco RV042 webpage:
Errors found while checking this document as HTML 4.01 Transitional!
Result: 353 Errors, 1 warning(s)
Don't even get me started on the horrible Javascript...
View 0 Replies
View Related
Apr 24, 2013
i am trying to make a simple Site to SiteVPN between two offices, one has Cisco ASA and one has RV042 router.when traffic initiated from ASA side, i keep getting this message in Debug and tunnel wont come up
.
[IKEv1]: Group = A.A.A.139, IP = A.A.A.139, Queuing KEY-ACQUIRE messages to be processed when P1 SA is complete.Apr 26 00:15:53 [IKEv1 DEBUG]: Pitcher: received a key acquire message, spi 0x0
whereas if traffic initiated from RV042 side, i keep getting this message in debug and tunnel wont come up.
Apr 26 00:43:44 [IKEv1 DEBUG]: IP = RV.RV.RV.139, Oakley proposal is acceptableApr 26 00:43:44 [IKEv1 DEBUG]: IP = RV.RV.RV.139, IKE SA Proposal # 1, Transform # 0 acceptable Matches global IKE entry # 6Apr 26 00:43:44 [IKEv1]: IP = RV.RV.RV.139, Connection landed on tunnel_group RV.RV.RV.139Apr 26 00:43:45 [IKEv1]: IP = RV.RV.RV.139, Connection landed on tunnel_group RV.RV.RV.139Apr 26 00:43:45 [IKEv1]: Group = RV.RV.RV.139, IP = RV.RV.RV.139, Freeing previously allocated memory for authorization-dn-attributesApr 26 00:43:45 [IKEv1]: Group = RV.RV.RV.139, IP = RV.RV.RV.139, PHASE 1 COMPLETEDApr 26 00:43:45 [IKEv1]: IP =RV.RV.RV.139, Keep-alive type for this connection: DPDApr 26 00:43:45 [IKEv1 DEBUG]: Group =
[code].....
View 1 Replies
View Related
Sep 27, 2012
Apparently one of my two ISPs,CenturyLink, supports 6rd connections to IPv6.
This is supported natively on my Q1000 ActionTec modem, however my modem is in "transparent bridging" mode, so that the RV042 v3 can be the only router.
how to configure the RV042 to operate in this manner.
Per the CenturyLink FAQ: the IPv6 address space is:
2602::0 /24
Most importantly, can I do this WITHOUT buying a new modem.
View 2 Replies
View Related
Aug 28, 2011
I have a RV042 router (Ser#: NKS10462300, HW V3) running Firmware version v4.0.2.08-tm (Jan 14 2011 22:08:38) set up as a gateway. Right after it boots I am able to long into its web interface but shortly after that if I try to log into it I go through a very log time out while the web page is waiting the router to respond and then eventually IE comes back and says it 'cannot display the web [age'.
View 30 Replies
View Related
Jan 14, 2013
I have a Cisco RV042 VPN Router and I have added a group vpn, but when I am trying to connect I got an error that the remote vpn server isn't responding.
Here's my log:
2013/01/15 12:24:53 [STATUS]OS Version: Windows 7
2013/01/15 12:24:53 [STATUS]Windows Firewall Domain Profile Settings: ON
2013/01/15 12:24:53 [STATUS]Windows Firewall Private Profile Settings: OFF
2013/01/15 12:24:53 [STATUS]Windows Firewall Private Profile Settings: OFF
2013/01/15 12:24:53 [STATUS]One network interface detected with IP address MY HOME IP
[code]....
If I am trying to connect the status of the vpn user in the remote interface is "online".I have deactived my firewall at home and at the server for testing purposes.
View 2 Replies
View Related
Feb 6, 2012
Is there any documentation out there on a step-by-step instructions on setting up a vpn on a RV042 router?
View 1 Replies
View Related
Apr 30, 2012
I'm trying to set up 2 subnet with two RV042 routers. One router will act as a gateway and both WAN ports will be used by two different isp connection. The first router (gateway) LAN IP will be 192.168.0.1/24. I would also like to set up another router behind the gateway with with separate subnet 192.168.1.X/24. And I would like clients on the 192.168.1.x subnet to use the internet through the gateway router and clients on the 192.168.0.x subnet to access resources on the 192.168.1.x subnet. Am I able to do this with two RV042?
View 6 Replies
View Related
Sep 2, 2012
The issue is when I am using PPTP the router seems to die, not every time but I would say about once a week now. I am the only PPTP user, simply using RDP. A few hours into an RDP session the PPTP connection drops and cannot be re-established, or quickvpn, nothing. Routing still works (somewhat, high latency) locally.
When I've checked the logs both times I see:
TimeEvent-TypeMessageSep 3 17:07:56 2012KernelOut of memory: Killed process 14354 (pppd). Sep 3 17:07:56 2012KernelOut of Memory: Kill process 14354 (pppd) score 177 and children. Sep 3 17:07:56 2012KernelOut of memory: Killed process 14367 (sh). Sep 3 17:07:56 2012KernelOut of Memory: Kill process 14354 (pppd) score 234 and children. Sep 3 16:46:41 2012KernelOut of memory: Killed process 14330 (pppd). Sep 3 16:46:41 2012KernelOut of Memory: Kill process 14329 (pptpctrl) score 134 and children. Sep 3 16:46:41 2012KernelOut of memory: Killed process 14324 (pppd). Sep 3 16:46:41 2012KernelOut of Memory: Kill process 14324 (pppd) score 177 and children. Sep 3 16:46:40 2012KernelOut of memory: Killed process 14328 (sh). Sep 3 16:46:40 2012KernelOut of Memory: Kill process 14324 (pppd) score 234 and children. Sep 3 15:36:15 2012KernelOut of memory: Killed process 14187 (pppd). Sep 3
[code]....
View 3 Replies
View Related
Nov 11, 2012
I have an RV042 connected via VPN to the office (to a LinkSys DFL-700). Sometimes the VPN is dropped and never activates again. In this state, if I try to connect to the WEB interface, I can log in, but the router hangs at the login screen. I have to power recycle the router to make it work again.
Updated to latest firmware 4.2.1.02 for V3 hardware. The funny thing is that services from the WEB routed through to local IP adresses on the lan is still accessible. I have setup PPPT VPN on the router, and that also fails to work.
Is there, as a workaround, any possibility to access the routers reset page or access via TELNET to reset the router? This migth be useful, when I'm out. (I have a backup solution to access the local network at home).
View 3 Replies
View Related
Jul 18, 2012
Are the RV042 and RV082 routers SIP AWARE?I haven't had any luck finding documentation stating such.
View 2 Replies
View Related
Feb 6, 2012
i have setup vpn connection (client-gateway) using quick vpn ( default cisco) and third party like thegreenbow. connection is ok (established) but why from outside I can only ping to IP LAN PC , if I ping ip server the result is request time out(failed). I have been trying do this to 3 server ( windows server 2003 as OS).four your information I have made firewall "OFF" on all of those servers. the result is same, failed.
View 0 Replies
View Related
Sep 28, 2012
I'm tryig to put a computer into the DMZ and then access it from computers on the LAN using a local IP address. My reason for doing this is that I'd like my DMZ computer to be a locked down web server (just ports 80 and 443 open to the outside), but I need to be able to have more access to it from inside my LAN (e.g. I want to be able to SSH into it from the LAN).
Thus far I've been able to get a computer set up in the DMZ and can access the Internet from the DMZ computer. And I can access the DMZ computer from the LAN computers using the public address for the DMZ computer. But I can't access the DMZ computer from the LAN computers using a private address for the DMZ computer. see the attached file for a diagram of our current settings. A few descriptions:
- Verizon provides us with a number of static IP addresses, i.e. 71.123.123.10-12 (note these aren't actually the addresses, but representative).
-- In the RV042, I have the following configurations made:
- Setup > Network > LAN Setting
- Device IP Address = 10.4.20.1
[Code]......
View 7 Replies
View Related
Dec 21, 2011
I have a static DSL connection and my ISP is giving me 4 static IP's. I have connected my RV042 to the DSL modem and I have now 1 subnet at 192.168.0.0. What I want to create is a WEB server/ Email server, but to sit on a different subnet - 192.168.5.0. For now I have connected the server to the DMZ port, but I am unable to to access it from WAN, only from LAN. How to configure properly the 2 subnets (192.168.0.0 and 192.168.5.0) and how to forward my static address to the server which I which to be on the 192.168.5.0.
View 4 Replies
View Related
Dec 18, 2012
i'm trying to set up a simple VPN (client to Gateway), but i can't ! An SSL VPN or an IPSEC VPN, whatever..
The firmware of the RV042 is up to date, and i'm trying QuickVPN as a client vpn (also updated...)
My configuration details :
I'm in : 192.168.2.14 /24
My RV042 : 192.168.2.250 /24
And the VPN intend to connect me to : 192.168.4.x
[Code].....
View 5 Replies
View Related
Jan 10, 2012
We are currently installing RV-042 V3 Dual WAN VPN Routers for a Customer with an HQ Office & 3 Branch Offices. The Customer recently requested to use the WEB Filter feature available in the RV-042 V3 Router to do the followng : - " Block all the HTTP Traffic Except for the company Website " We tried all the Combinations between " Access Rules " & " Content Filtering " available under the " Firewall " but we always reach the result that either to Allow ALL HTTP Tarffic to All Websites or to Block ALL HTTP Traffic.
how to Block all HTTP Traffic except for certain URL ( Using the URL Name NOT the IP Address ).
View 3 Replies
View Related
Mar 31, 2013
I've got half a dozen RV042 routers in various locations. They are running v4.0.0.07. Seemingly randomly, I got the 502 Bad GatewayThe CGI was not CGI/1.1 compliant. error when attempting to log into the web interface with google chrome (same with IE too). This happens from the LAN side. I actually didn't notice it until my Opsview monitoring software threw up a critical when it didn't get an http response. The router is otherwise actually working just fine.Since the first occurrence, more of my routers have developed the same error.
I've tried different browsers, clearing caches, though I'm not surprised those efforts were fruitless, as there is clearly a problem even when no browser is involved (nagios). The nagios http check also returns a 502 Bad Gateway.
View 7 Replies
View Related
