Cisco Routers :: Are RV042 And RV082 SIP Aware?
Jul 18, 2012Are the RV042 and RV082 routers SIP AWARE?I haven't had any luck finding documentation stating such.
View 2 Replies
ADVERTISEMENT
Cisco Routers :: Convert The RV082 File To Work In A RV042?
Sep 22, 2011I have tried to load the config file from an RV082 to an RV042 with no luck.Is there a way to convert the RV082 file to work in a RV042?
View 3 Replies View RelatedCisco Routers :: RV042 To RV082 Tunnel / NAT-T And Slow Performance?
Feb 18, 2013I have an RV042 VPN tunnel with an RV082.The RV042 has a public IP Address obtained by PPPoE, the RV082 has a public IP Address obtained via Static IP.The problem I see is a really slow performance. Both internet conections are idle and the performance is about 2 or 3 kbyte/s My question are if I should I enable any of this:
- Agresive mode
- NAT Traversal
- IP Compresion
- Dead Pear Detection
How can I troubleshot this slow performance?
Cisco Routers :: How To Redirect Internet Traffic From RV082 To RV042 Through A VPN
Feb 24, 2013We have offices in USA and Venezuela.In our USA office we have a RV042 router and in Venezuela we have a RV082 router.We have connected a VPN tunnel (gateway-to-gateway) between both offices.
The point is:How could we redirect the internet traffic from our Venezuela office (RV082) to the USA Office (RV042) to navigate using USA public IP's?
The reason for this is that we need to use online streaming services which are only available for IP's from USA and we can't use them from the Venezuelan IP's.
We can not use the PPTP option since the equipment which will use the streaming services (like hulu, crackle, etc.) in Venezuela is a Google TV device which doesn't allow the configuration of proxy navegation or PPTP VPN connections itself. That's the reason why we need to do that through the routers.
Cisco Routers :: RV082 / RV042 - Can't Remotely Administer Through VPN Connection
Nov 19, 2012I have an RV082 and a RV042. I have been able to successfully establish a gateway to gateway vpn connection between them both, but both Routers unable to ping each other and I can't remotely administer each router through the VPN connection.
View 1 Replies View RelatedCisco Routers :: RV042 And RV082 Difference Between Logs Action
Apr 20, 2013I have RV042 V01 and V03 and RV082 V03.I'm wondering if there's a difference between the default actions taken by the "Logs" interfaces?
In the case of the V01 systems, it appears that I get a Security Notification every hour.In the case of the V03 system, it appears that I rarely get a Security Notification.
Cisco Routers :: RV016 / RV042 / RV082 Internal Port Forwarding?
May 16, 2012I'd like to setup a WCCP in those routers, but as I read, it's not possible.
Another way to circumvent this limitation is to foward a request to the router from the LAN port 80 to a LAN IP, something like:
LAN 1 192.168.1.100:80 -> router -> LAN 2 192.168.1.101:80
Linksys Wired Router :: Getting RV042 And RV082 Throughput?
Feb 17, 2008I am currently using Netgear FVS338 Routers / VPN Devices in 3 different locations and honestly I am not happy / impressed with them whatsoever.I have been doing some research and came across the Linksys RV042 and RV082 devices that caught my eye. The question is what is the VPN throughput of these devices?I have gone over the website, spec sheets and they only really say the throughput of the LAN Links and not the WAN Links. I currently have very reliable 20Mb+ Synchronous connections between all 3 sites and have not been able to get any good performance out of the Netgear devices and contacting their support is a joke. They can't tell you anything other than it should work or we will swap out the unit. Well if I have 3 of them that have been purchased at all different times I don't believe that they are all having the same issues. What these units 3DES VPN Throughput and will more than likely be purchasing 3 of which ever once suits our needs immediately.
View 9 Replies View RelatedLinksys Wired Router :: RV082 VPN Pass-through Not Behaving As RV042?
Aug 15, 2012We have almost identical networks in two offices, with the only difference being, one uses an RV042 and the other an RV082.The setup is: two WAG54GS ADSL modems carry PPOA ADSL connections with static IPs to the two WAN ports of the RV0XX.The WAG54GS routers are configured to DMZ all incoming traffic to the relevant WAN IP of the RV0XXs. VPN pass-through is also set on them. The RV0XX port forwarding is set to forward a selection of traffic such as, PPTP, HTTP, HTTPS, RDP, POP3, SMTP and Remote Desk to the external adapter of an SBS 2003 server which processes all operations including ISA and Exchange.Mail for Exchange arrive through both ADSL connections for redundancy. VPN connection requests from remote users to the SBS come in through both ADSL connections.The office fitted with RV042 works fine and does all the following without problems.The office fitted with RV082 has issues. Remote VPN requests comming from ADSL to WAN port 1 of the RV082 connect successfully to the SBS2003 server, but the VPN requests coming from ADSL to WAN port 2 fail to connect! Similarly, incoming mail destined for Exchange don't get through if coming from ADSL of WAN port 2.I have updated the firmware on both RV042 and RV082, but the RV082 still has the above issues.
View 1 Replies View RelatedLinksys Wired Router :: RV042 / RV082 Timeout Bug Found
Jan 23, 2008telnet/ssh sessions time out after 30 minutes of in-activity This only happens in the case of a server that is setup behind the firewall, and of course port forwarding is used. If one unchecks the radio button for the enable firewall the sessions do not timeout at all. This is very reproducable in all recent (1.3.9) versions of RV042 and RV082 routers.
View 2 Replies View RelatedLinksys Wired Router :: How To Redirect Internet Traffic From RV082 To RV042
Feb 24, 2013In our USA office we have a RV042 router and in Venezuela we have a RV082 router. We have connected a VPN tunnel (gateway-to-gateway) between both offices.
The point is: How could we redirect the internet traffic from our Venezuela office (RV082) to the USA Office (RV042) to navigate using USA public IP's?
The reason for this is that we need to use online streaming services which are only available for IP's from USA and we can't use them from the Venezuelan IP's.
We can not use the PPTP option since the equipment which will use the streaming services (like hulu, crackle, etc.) in Venezuela is a Google TV device which doesn't allow the configuration of proxy navegation or PPTP VPN connections itself. That's the reason why we need to do that through the routers.
Cisco Routers :: VPN Between Two RV082 Routers Not Working?
Aug 7, 2012We're getting the following message in the logs when we ry to connect: encrypted Informational Exchange message is invalid because it is for incomplete ISAKMP SA
One of the router is a V2 and the other is a V4 if that makes any difference.
Cisco :: VRF Aware Peering With Straight BGP?
Mar 24, 2013I have a scenario where I may have to run VRFs on a router that is currently facing an ISP as a BGP peer. peering two BGP peers, one of which is VRF aware (and hence configured within the address-family ipv4 vrf X subsection) and the other is not? (the BGP aware and internet facing segment will go into its own VRF where previously this router was only in that VRF and hence had no awareness).Are there any caveats or restrictions? Does the presence of the VRF throw the ISP peer?
View 3 Replies View RelatedCisco Routers :: Auto / Programmatic UPnP Port Forwarding For RV042 And E4200 Routers
Jan 24, 2013I have RV042 and E4200 routers . I tried the manual UPnP port forwarding using Rv042 router and was succesful ( by typing 192.168.1.1 in the explorer and logged in using user name and password )
I am using a linux embedded system whose Internal IP ,Internal port are mapped .This system is connected to one of the LAN ports
I want to try auto UPnP port forwarding both for RV042 router and Linksys E4200 routers
After enabling the Upnp option only and logging out ,Can i add a port mapping entry in this router without logging in using a C++ program which runs on linux embedded system .
Cisco Routers :: RV042 / RV042G / Small Business Routers With Inter-VLAN Capability
Aug 22, 2012I was looking for a small business router that has VPN support and dual WAN support for load balancing. Upon reading reviews, I think RV042/RV042G is a good choice. Now am thinking if it supports intervlan/ router-on-a-stick configuration?
View 5 Replies View RelatedCisco Routers :: LAN To LAN Routing RV082?
Jan 29, 2013We have an RV082 setup with WAN to the internet and LAN IP of 192.168.188.1.If I add a static route like so:
network: 192.168.166.0
mask: 255.255.255.0
gateway: 192.168.188.2
hop count: 1
interface: LAN
The device with IP 192.168.188.2 will be connected directly to one of the LAN ports on the router.Will that work to route, trying to get to 192.168.166.0 to the IP of 192.168.188.2?It just seems odd because the packets would hit the router then go back out through the LAN port.
Cisco Routers :: Rv082 Configure One-to-one Nat
Nov 17, 2011isco epc3925 in transparent bridge provided by isp with following wan details
ip=x.x.x.120 subnet=255.255.255.248 gw=x.x.x.121 and 2 dns server ip's
I can't get the one-to-one nat working. read in some forums that the rv082 can do the job.
Cisco Routers :: RV082 VPN Passthrough
May 9, 2013I have a Meraki Firewall that sits behind my Cisco RV082. The Meraki is setup to run a VPN connection with my server but I am having problems passing the VPN traffic through properly.
I have 2 Uverse Internet Connections that the RV082 using load balancing so that they are shared. I have 10 static IP's.
I am trying to come in on one of my static IP addresses throught the Cisco RV082 to the Meraki and after doing a capture on the meraki it appears that it is starting to receive data to intiate the VPN connection but when it sends data back to the VPN client machine it never makes it.
Cisco Routers :: RV082 / No Connection To ISP
Nov 12, 2012I have reset my RV082 router (both wit the reset switch and the factory default wizard) and run the setup wizard but regardless I can't connect to shaw.ca which is my service provider. I notice that if I use http://192.168.1.1 the browsers (IE & FF) default to https://192.168.1.1 and then I am prompted for a certificate. I can enter if I ignore the request but after getting in I simply cannot connect to my ISP.
View 4 Replies View RelatedCisco Routers :: RV082 NAT To Other Subnets?
Jan 12, 2012Is it possbile to NAT to other subnets with the RV082. It is on a 192.168.41.x and I have a phone system on a 192.168.20.x. After searching all over others are saying no.
View 4 Replies View RelatedCisco Routers :: VPN Fail With RV082
Jan 14, 2013I just set up a new Linksys/Cisco RV082 router with the intent to get VPN working from outside the building. I have gone through the setup and while everything looks good, I have not been able to connect yet. I have tried everything that I know how, and am now hoping to get the answer from some pros.
Here's my setup. We use Comcast Business class internet. The modem is plugged into WAN port 1 on the RV082. I'm using the router as a DHCP server, that is working fine. My local subnet is 192.168.0.0/220
Right now all I want is to be able to log in as a client using QuickVPN. I set up one user and a client to VPN tunnel using the router's config page. Here's the settings I have:
Tunnel Interface is setup on WAN1, checkbox is enabled.
Local Group Setup
Local Security Gatewaytpe: IP Only
Local Security Group Type: Subnet
[Code]....
It seems like something is blocking the connection, but seeing that I have tried this after disabling the firewall completely it doesn't make sense to me. I also went into the config page for the modem and set up the router as a DMZ. I have also tried connecting with the client built into Windows 7, but that doesn't work either, I just get "connection failed with error 619"
I have the port in QuickVPN set to auto, but have tried both 443 and 60443 with same results.
I ran a port scan at [URL] and it shows I have 3 ports open...80,443, and 1723
Cisco Routers :: VPN Not Working With RV082
Jan 24, 2012I have a VPN tunnel from one RV082 to another, first router has IP range of 192.168.1.0 and the second one has range of 18.18.18.0, the connection works fine, here is where the issue starts, I am at a PC in the 18.18.18.0 network and I ping an IP in the other one e.g. 192.168.1.50 and it pings fine, but when I try to RDP into it or do anything to it I get no response, is it a firewall issue? Is it a NAT issue? I am at a loss, now that IP i mentioned does have RDP enabled and working because it is being port fowarded in the 192.168.1.0 router and I can access it through the public IP.
Also a workstation with a static IP 192.168.1.18 I can ping it if im in the local network but if I am in the remote one I cannot at all.
Cisco Routers :: RV082 Restarts Itself
Jul 28, 2010we have an RV082 router that a few days ago started restarting itself after normal usage.The simpton is that when people come to office, starting using the Internet the RV082 resets. It stays online for 3 to 12 minutes and then it resets again.
clicking on Reset to Factory Default in the web interfaceafter the reset, I confirmed that it was reset to factory default I reset it again using the reset buttomre-configure the RV082 manually.I also tested with another identical rv082 (hw version and firmware version) and after doing a backup of the config of the original rv082 and restoring it in the new rv082, the same problem happends.
Cisco Routers :: RV082 NAT Table Too Small
Mar 15, 2013I have an RV082 10/100 8-Port VPN Router and have configured the NAT table to allow for remote users, however I've run into an issue. It seems like there is a limited number of entries that you can put in the table,10, and I need to configure about 5 more IPs. Any way to expand the NAT table, or alternatively recommend a different router. I would also be willing to add another router to the network, but I have little experience doing that.
View 3 Replies View RelatedCisco Routers :: RV082 Web Admin Lockup?
Oct 20, 2011Just purchased a RV082 and once I switched a bunch of users over to it I can no longer access the web admin section. I have tried using both IE and Firefox and have used multiple workstations. I get to the login screen but it doesn't get any further. I am running the latest firmware v4.0.4.2-tm. It works for a while then just stops. The only fix is to turn off the device and back on and then it starts working again.
I've seen this issue on other small business cisco devices and had to stop using this because of this issue and switch to a higher grade cisco product but was hoping that this particular issue would have been resolved now across cisco's products.
Cisco Routers :: Outbound Nating With RV082?
Jan 9, 2012I just migrated our office network router to a RV082. While configuring it, I came across three problems:
(1) From our ISP we have four public IP addresses which I want to make use of for outbound traffic. With the previous router we used we could configure LAN IPs(ranges) to map to static public IPs. Does RV082 support this? I could not find an option for that at the web-interface. From what I understand the 1-1 NATing only goes both incoming and outgoign ways and actually is 1-1 and not the many-to-one I am looking for.
(2) How is it possible to configure incoming port forwards to use a specific WAN interface? Will it always be the primary WAN interface?
(3) Does the telnet access provide more configuration options? I could not log in to it with the same user credentials as with the web-interface.
Serial Number : NKS1532xxxxFirmware Version : v4.0.4.02-tm (Jul 4 2011 13:30:56)PID VID : RV082 V03Firmware MD5 Checksum : 1f84d8d0a2a8b99f9bfa4409e64547aaLANWorking Mode : Gateway
Cisco Routers :: Rv082 Dmz Rule Limitations
Apr 27, 2013we have a RV082 and have the DMZ option enable for a range of IPs within the same subnet of WAN IP and this works great. I have another range of Public IPs from our ISP that is not in the same subnet of the WAN IP and do not see a way on the RV082 to include this 2nd bank of Public IPs in the DMZ. Our ISP internet feed plugs into the RV082 WAN port and we have a switch pulgged into the DMZ port of the RV082 that is used to connect the public devices in the current DMZ. Both banks of Public IPs from our ISP come over via the ISP internet feed plugged into the WAN Port. My question is, if I cannot configure a DMZ rule to allow this 2nd range of Public IPs to "travel" to the RV082 DMZ port.
View 0 Replies View RelatedCisco Routers :: RV082 LAN Subnet Mask
Nov 12, 2012I would like to set the subnet mask off the lan to 255.255.240.0 but the selection menu do not allow to do it.
View 8 Replies View RelatedCisco Routers :: Can Connect SA520W To RV082
Sep 25, 2012I wanted to know if you can connect a Cable modem to a SA520W, then connect a RV082 to the SA520W?
View 5 Replies View RelatedCisco Routers :: RV082 VPN - Connects But No Access?
Mar 24, 2013We recently moved our network over to RV082 router and its working great, well now we want to take advantage of VPN for our sales staff.
I was able to setup the VPN and using a PC at a remote office I can launch the quick connect and it connects right away, RV0 even shows the user connected. However the user cannot ping anything on our network via name or IP, connect to any resources, etc...
My understanding was when the client VPN would connect the user would get an IP from DHCP (this is on our Server 2008 DC) and they would be using that address, but when I run IPCONFIG on the client PC they just have there standard IP from remote office.
Cisco Routers :: RV082 Backup Vpn To C2851?
Feb 10, 2013I'm planning to buy a few Cisco RV082's for remote offices and using them to connect to main office Cisco 2851 site to site vpn. So I guess, simple site to site vpn will work without much problem, but I wonder, will backup vpn feature work as expected on backup WAN channel and how should I configure it on the IOS side?
View 1 Replies View RelatedCisco Routers :: RV082 - Internal DNS Server
Jan 19, 2010The RV082 is a great unit, however when VPN clients connect the QuickVPN Client has a setting to use the Remote DNS settings of the RV082. The RV082 has no way of linking or using a user-defined DNS. I have an internal DNS Server that I would like the VPN Clients to query on internal name lookups (kindof the point of having client vpn, so they can access internal network shares etc. On the diagnostic page the ping and name resolution can only check external DNS and internal IP's. Wouldn't it make sense to at least make the RV082 aware of internal DNS Servers? Then the Ping and DNS lookup would be able to test both zones? Is this something that can be looked at by Linksys Developers for this product? The WRV210 (a cheaper and lower level model) has this functionality.
View 8 Replies View RelatedCisco Routers :: RV082 V3 Web Management Inaccessible
Aug 29, 2012Experiencing a strange issue with v3 hardware. After a short period of time, I cannot log into the web administration - either locally through standard port or remote through non-standard port get login prompt, enter correct username & password, page refreshes with blank background and first page (status?) never shows.power cycling the router restores access to the web administration page, for an uncertain period of time before it barfs again.
I was running older firmware, updated to newest 4.2.1.02 (?) and same problem. Only thing that is better is the internet didn't completely lock up when I tried to access the administration page, like it did on the older firmware.