Cisco Routers :: RV120w Trunk Mode Feature Listed In Manual But Not In Web Console
May 30, 2012
I bought an rv120w. Now i want to trunk 2 lan ports to an smart switch to get 200MB out of that link.
The trunk mode in there in the manual that came in the cd with the unit i bought but is not in the web console.
I have updated the IOS to 1.0.3.10 to see if th trunk mode was there but is not.
My question is,
1 is that trunking feature there in the ios?
2- If not, why is listed in hte manual that came with the unit?
3- if it is in the ios, is there a was to by pass the web console and configure this?
4- can i do i maybe backing up the config then, editing the file and restoring it?
Screenshot below is from the manual in hte cd that came with the router
View 2 Replies
ADVERTISEMENT
Jan 1, 2013
We have a RV120W Wireless-N VPN Firewall and we want to configure the router in brigde mode (transparent). Because we have another Firewall, use for filtering and default gateway on the LAN. The ISP provide IP address by DHCP, so we must connect the internet connexion to the WAN interface. But How can we do for connected the RV120W to our firewall? The router mode on the RV120w allows-it to make this configuration?
View 1 Replies
View Related
Sep 11, 2011
I am trying to configure a BT Business ADSL Router (BT2700HGV) to work in bridge mode in front of a Cisco RV120W router and cannot get this to work.I have followed numerous posts I have come across in configuring the BT router for bridged mode and this has been configured as follows:
ATM Encapsulation - Bridge LLC
DSL and ATM - VPI=0, VCI=38 (also tried VCI=35)
ATM PVC Search - Disabled
Connection Type - Direct IP (DHCP or Static)
Disable Routing - Yes
There are also some other options on the same configuration page for 'Broadband IP Network' (which I have left on DHCP) and also a 'Public IP' which has been left blank. After setting the above options this removes the LAN DHCP configuration, the PPPoA logon details and sets the internal IP address of the BT router to 192.168.1.254.
My understanding of 'Bridge' mode is that this router will now act simply as a modem and configuration details such as logon details and WAN IP address information are configured using the Cisco RV120W router?The configuration of the Cisco router is as follows:
Internet Connection Type - PPPoE
Username and Password set
Authentication Type - Auto-Negotiate (options here are PAP, CHAP, MS-CHAP and MS-CHAPv2)
Routing Mode - Router (Other option is 'Gateway (NAT))' - I have tried both options
The WAN interface on the Cisco router is connected to one of the LAN ports on the BT router. The 'Broadband' light is on the BT router but the 'Internet' light isn't. The WAN status on the Cisco router is 'Connecting'. I am sure I am missing something simple.We have been assigned a range of static IP addresses from BT so am trying to get these working too (x.x.x.24/29 - 5 usable statics), another option available (other than PPPoE) for configuring the WAN interface on the Cisco router is a 'Static IP', not sure if this is the correct option but have tried messing with it, I have tried assigning a static IP from the range given to us (.30 - the router address specified by BT) along with the subnet mask, however don't know what to put as the default gateway, would this be the peer address (but assume that would change anyway), in any case, using the 'Static IP' option does not give an option to supply the BT logon details which I assume is required?
In bridged mode, what is the peer address assigned to, the BT router or the Cisco router?Does the BT router need to be configured with a public IP address?
View 2 Replies
View Related
Mar 29, 2013
I was trying to set this up pointed out a back window, but obviously ran into the IR lights reflecting back on the glass. I don't have an external IR light yet, but just tried the manual IR mode and the IR lights stay on.
View 9 Replies
View Related
Feb 10, 2012
I want to know if it is possible to put the cisco small business router rv120w into bridge mode so that I can connect it to a linksys e2500 access point. Is this even possible or am I wasting my time?I have 4 devices connected to the cisco router that I want to be able to bridge to the linksys e2500 which has the internet connection.
View 1 Replies
View Related
Apr 16, 2012
recently i do some lab about trunking protocol using Layer 3 switch C3560 and layer 2 switch C2960, but i face a problem that i cannot configure trunk port on my C3560 using "switchport mode trunk" command, and after looking for the answer from google i found that i have to "remove" the "auto" mode of C3560 using "switchport mode dynamic desirable" and after that we can enter the "switcport mode trunk" command successfully.
and my question are, whether the "auto" trunk mode in switch layer 3 is a default mode or not? and why i should enter "sw mode dynamic desirable" command before "sw mo trunk" command ?
View 5 Replies
View Related
May 18, 2011
I'm having some issues trying to reserv an IP from my D-link DIR-825 router.I have set up a static IP on my computer: 192.167.0.10. But if i view the clients on my network that ip doesn't show up!
View 2 Replies
View Related
Nov 29, 2011
On a SF300-08, how to work with CLI and not with the Console Menu Interface ?
View 4 Replies
View Related
May 10, 2012
I've previously used trunkports and vlans between my ASA and accesspoints, connected directly. Now I want to put a 2960S-24PS-L bewteen. Where should i define the vlans (in the switch or in th ASA?) and what ports to put in trunk mode? (the ones on the switch or the one between the switch and the ASA?)
View 1 Replies
View Related
Jun 15, 2011
We have a 5580 that we want to connect to each of our 7K's as an internal firewall. To minimize hassle, we will setup the ASA in transparent mode.I have been working on this all day today and have run into a stopping point. If I put vlan 20 on a subinterface on Te7/0 which will connect to N7K_1 it works great. When I try to put that same vlan on Te7/1 which connects to N7K_2, I get an error that says the vlan is already assigned to another interface.Our local Cisco SE told us that this would work.
My problem is that not all of our servers/systems are dual homed to both 7K's so I have to be able to get this to work because of potential asymmetric routing issues that we will be dealing with.How to get the 5580 to work in this configuration and can you share your config with me ?Using the redundant interface command isnt an option because I need for both interfaces to be able to route over both 7K's at all times.
View 3 Replies
View Related
Jan 20, 2013
Can I configure the Port at the ASA 5050 from Mode: access Port to trunk during the FW is running in a production area without console access ?As I know at the 5505 ist should work?
View 3 Replies
View Related
Jan 25, 2012
I use a C2950-24 switch, with IOS 12.1(22)EA12 release.When I try to connect in console mode, I can see the "Press RETURN to get started!" message, but it's not possible to me to have the # prompt.An "authorization failed" message is displayed. And the same message is prompted.
I try to recover password by following the recovery procedure. After the boot command, I never see the message "Continue with the configuration dialog? [yes/no]: ".
View 6 Replies
View Related
Mar 15, 2012
we have a scenario that consists of a Cisco 4507 series core switch with more than 20 vlans which is connected to a C2960G switch( in a nearby building) using a trunk by a fiber connection. Up to this point everyhting is fine . VTP domain is configured on the core switch and we have all of the 20 vlans present correctly on the edge 2960G wich is part of course of this same VTP domain.the fiber connection goes from core switch to a "in the middle location" where we have a fiber patch panel that is connected in a jumper style to another fiber patch panel going to the destination building where the C2960G sits.
Now imagine that Fiber connection from this middle location to the destination C2960 edge switch is down for any possible reason meanwhile the fiber connection from Core switch 4507 to the middle location is still intact.In the same time, in this middle location , we do have a wireless connection which links 1 Cisco 3750G switche ( a different infrastructure and different VTP domain) to another C3560G switch which sits on the same Room in the nearby destination building where we have the edge C2960G, An idea came to me is to connect one of the fiber port (core) in the intact fiber patch panel coming from Core switch 4507 TO an access vlan configured switchport in the 3750G switch ( this switchport will belong to a vlan designed only to trasmit the vlans on the trunk coming from 4507 core switch say VLAN 10) then connect one VLAN 10 access switchport to the destination C2960 edge switch ( the switchport on the c2960G is still a trunk)Will this solution work and all of the 20- 4507 core switch vlans arrive to the destination C2960G ? Or we do need something that tags the 2 VLAN 10 switchports like switchport dot1q tunnel like QinQ
View 2 Replies
View Related
Jan 16, 2013
This is regarding VLAN creation on C3750E switch.I want to create new Vlan 94 on this switch and also I want to allowed same interfaces like Vlan 95 & Vlan 96. [code]
View 7 Replies
View Related
Mar 27, 2013
I faced with a strange behavior of ME3600.For testing purposes I linked Cat3550 and ME3600 switches via trunk mode. All interfaces are in Up state. But I couldn't ping SVI200 of Cat switch from ME3600 and vice versa. [cde]
This scheme perfectly works with another L3 swithes. For example Catalist3750. I know that ME doesn't support VTP, DTP and so on. Also, I've tried latest software.
View 0 Replies
View Related
Oct 3, 2011
We have an RVS-4000 router that we use as an Internet gateway on our school network. I am trying to set up an Internet Access Policy to block some specific websites by URL using a domain name. I set up the policy, and added a PC to the list using the mac address, and the blocking did not work. I went back to the list and added the IP address of the same PC, the policy still did not work to block the domain. I rebooted the router, cleared the Internet Temporary files and history on the PC, and the policy still does not work. It acts like it is going to block access to the website because it takes a long time, but it will eventually connect.
View 7 Replies
View Related
Mar 6, 2012
I have a problem for config switch sge2000. I can not console mode to get the prompt to type commands
View 1 Replies
View Related
Jan 14, 2012
I am using radius authentication on C4507R+E with supervisor card 6L-E and IOS 15.0.2(SG1). It works perfectly but all radius messages appear in the console. Radius is very verbose, I can't use console because of the significant number of messages and I am worried about switches performances. I add that all debug commands are disabled.
View 1 Replies
View Related
May 8, 2013
WRVS4400N needs to be manually connected when the power is recycled after power failure. Is there a setting to connect an IPSEC VPN automatically, instead of manually going in to connect the VPN
View 3 Replies
View Related
May 10, 2012
I have 2691 router with following config
line console 0
login local
password xty
When i remove the login local from the line console i connect to console port and press enter it shows router prompt 2691Router> but i am unable to go to enable mode.If i telnet to router then i put username and pw then it goes straight to enable mode.
vty config is
line vty 0 4
exec-timeout 600 0
logging synchronous
login local
length 500
transport input telnet ssh
escape-character 3
Any reasons why i can not go to enable mode by console?
View 3 Replies
View Related
Jun 13, 2012
I'm using Linksys WAG200G Wireless modem and connection mode is "Bridge Mode Only", in this mode I'm not getting the 192.168.1.1 setup console and Wifi facility.
View 3 Replies
View Related
Nov 3, 2012
I've been noticing that occasionally our 2nd Gen RV082 fails to allow internal admin management until a manual restart. After the restart, all seems to be fine and traffic/router is very responsive. The following describes typically how the issue occurs: Internet traffic is rather slow and unresponsiveContent is failing to load for end usersWebsite are loading but with images or css failing to loadWebsites fail to load and appear offline (not all, but some such as ebay for example)We recognize there is a problem, let's try to access the local router adminFails to load the log-in prompt, so we manually reboot the deviceAll is operational for now We are running Firmware Version: 2.0.0.19-tm. [URL]
View 2 Replies
View Related
Feb 7, 2012
I would like to set up a site to site VNP connection between 2 RV120W routers, preferably via IPsec.
The problem is that I would like/have to use a 4G modem router (model TINY) which connects to internet in front of the RV120W (on the local side)
I have no problem with that on the remote site that RV120 connects directly to internet via a public IP address on the WAN port.
Local network 192.168.1/24-----RV120W----192.168.100.1—Tiny---Public IP--------INTERNET
INTERNET--------PublicIP—RV120W—Remote local network 192.168.2/24
View 1 Replies
View Related
Jan 12, 2012
I've a RV120W with the last firmware version (june 2011), i want to create two vpn tunnel:
- Professional: lan routing all packet for the 192.168.0.0/24 to the first VPN tunnel
- Other: all other address IP destination to a second VPN tunnel
The first tunnel (professional) is ok but what rules can i use to configure the second ?
View 2 Replies
View Related
Feb 8, 2012
What is the default login/pass of cisco rv120w for ssh access ?
View 1 Replies
View Related
Sep 24, 2011
Upgraded to 1.0.2.6 and all of a sudden SIP devices working over the VPN no longer work. Downgrade to 1.0.1.3 and they work again. My guess is that some ports are blocked over the VPN in 1.0.2.6
I thought the general idea was that firmware ugrades fixed bugs rather than introducing them.
Suggestion for Cisco:- Zip the firmware image downloads, or else have an upgrade process that includes a CRC check, that way at least the poor punter will have an indication if they have been corrupted. I had a subtle memory problem that was corrupting some files. The firmware upload appeared to complete properly and you could log on OK but some of the menu choices resulted in a hang with the "Please wait... the page is being loaded" message. Careful checking of file sizes revealed that the file I was uploading into the router was a few hundred bytes different in size to the one on the website, must have been corrupted during the download. But the upload proceeded normally with no indication of any error. It's a pretty basic safeguard that should be in there as a matter of course with the router performing a CRC check and showing an error if it fails.
View 2 Replies
View Related
Mar 31, 2012
I had WRT54G2 and recently switched to an RV120W. I have an Internet accessible camera system connected to my router. Before, this worked fine... there is a dns service (DynDNS.com) that is configured as part of the camera setup. I would then just enter [URL] and I would connect to the cameras. I install the new router (RV120W) and I can no longer connect to the cameras. I do not recall any configuring that I had to perform on the old router.
why the RV120W isn't letting me get to the cameras?
View 3 Replies
View Related
Sep 12, 2011
Rx:, recently I have perchase 2 RV120W routers thinking that it must be very easy to setup the site to site vpn. i cannot get my remore office to link to my main office and vice verser.
Scenaro
- I'm using 2 RV120W routers for each site.
- Site A using a subnet of 192.168.10.0 mask 255.255.255.0
- Site B using a subnet of 192.168.11.0 mask 255.255.255.0
I have setup the VPN using the wizard and I got site to site tunnels connected and show as 1/1 Connected (1 user) in the status he IPsec connection status show
--Policy Name: VPNA
--Endpoint : public IP address from my ISP 203.117.222.221
--Packets Tx:145 Rx:0 and Kbytes shows Tx: 29.55 Rx:0
Q1 why I cannot use dynamic DNS naming in the policy setting ? eg: aaa.dyndns.org, I have to use the ip address instead eg: 203.117.222.221
Q2. I cannot connect from Site A to Site B , I can't even do a ping to 192.168.11.1 from Site A. even though it show the Site to site tunnel is coonected.
View 2 Replies
View Related
Aug 6, 2012
I've just set up an IPSec VPN between 2 x RV120W which are both behind other router. Here's what we have :
RV120W #1 (192.168.1.254) --- (192.168.1.1) Office Router #1 (PUBLIC IP) --- (((Internet))) --- (PUBLIC IP) Office Router #2 (192.168.2.1) --- RV120W #2 (192.168.2.254)
It works great, tunnel is UP.
[Code]....
View 1 Replies
View Related
Nov 21, 2012
I've just set up an IPSec VPN between 2 x RV120W which are both behind other router. Here's what we have :
RV120W #1 (192.168.1.254) --- (192.168.1.1) Office Router #1 (PUBLIC IP) --- (((Internet))) --- (PUBLIC IP) Office Router #2 (192.168.2.1) --- RV120W #2 (192.168.2.254)
[Code]....
Now, I need to be able to reach the server (192.168.1.100) from a PC on LAN #2 with IP 192.168.2.50. So, I've created au static route on Office Router #2 (192.168.2.1) because of course it doesn't know how to reach private subnet 192.168.1.x. My static route looks like this :
192.168.1.0 / 24 (Destination network) --- 192.168.2.254 (Gateway)
...but it doesn't work, no ping. When I do a tracert to server IP (192.168.1.100) from PC on LAN #2 (192.168.2.50), the result is :
1st jump ---> 192.168.2.1
2nd jump --> 192.168.2.254
...and it doesn't go further.
View 3 Replies
View Related
Dec 21, 2011
I configured my RV120W (Firmware:1.0.2.6) to count the traffic on my network. I set the monthly limit to 99999 and did not change anything else.So after a few hours, the traffic counter shows 2048 MB for outgoing traffic. This is impossible, because the DSL-connection is too limited in upload to cause this huge outgoing traffic in 6-8 hours. When I reset the counter at night, the next morning the device shows 2048MB again (even if there was no traffic at all, just some clients syncing time with NTP). I did already reset the device to factory defaults and reconfigured everything from scratch.
View 0 Replies
View Related
Jul 5, 2012
I have a problem with firewall rules. If I set some rules for open communication and some for closed, so I cannot reorder from the end to begin.
Last rules are at the end of all. So I can only reorder in one pages.(I have about 33 rules = 3 pages of rules)
View 4 Replies
View Related
Oct 24, 2011
I was wondering if I could setup my router CIsco RV120W to be able to connect to a VPN serice for my internet connection. Looking to give my small home netwok more sercurity. Is it possible with the Cisco firmware to be able to setup a connection to VPN serice. Do I have the compabilites with this router?
View 1 Replies
View Related
