I'm having some issues trying to reserv an IP from my D-link DIR-825 router.I have set up a static IP on my computer: 192.167.0.10. But if i view the clients on my network that ip doesn't show up!
View 2 RepliesI recently noticed my 'Number of Dynamic DHCP Clients' on Network Settings is always empty. Before, it always registered a list since there are several devices that are connected to our wireless network (laptops, mobile phones, desktops).
View 3 Replies View RelatedThis may sound ignorant but I cannot get either of the antennas off my 615. They are listed as removable reverse SMA but they are so tight I am afraid of damaging it. This is my second 615 after not being able to get one of the antennas off the first. D-link said they should just unscrew but I cannot get either of them to budge. D-link support said the one I had first must have been manufactured wrong so I returned it to new egg and got a new one. Same issue. I need to have an external antenna on the unit.
View 11 Replies View RelatedWe are trying to manage our Cisco ASA 5520 (8.2.5) SSL clients through Active Directory(ldap).
Currently the SSL VPN tunnel is up and all users are able to connect being authenticated by AD. but Group-policy to AD groups are not working. all the domain users are able to go to all the group policies .
I need to give access only to their respective Group policy in ASA. Following are the available groups and GP.
Code...
I have 4 desktops cat5 to Dlink DIR 615 router. All work fine. Any wireless clients, laptop or netbooks, see the desktop computers for a while then disconnect somehow. All machines can see the Internet through the router at all times. The desktops disappear from the laptop/netbooks but the wireless machines can be seen from the desktop computers but clicking on them gets 'Access Denied' message after a wait.3 desktops = XP, 1 98SE. All laptop/netbooks = XP
View 2 Replies View RelatedI'm trying to get a couple clients to talk to my Active Directory servers. I've created sub-interfaces on my ASA. So, my clients are on Gi0/1.139 and my two Active Directory servers are on Gi0/1.132. I've enabled traffic on TCP 53-5000 port range according to Microsoft. My clients still can't join the domain. What ports I need to open up? My AD servers are Windows 2003.
View 1 Replies View Relatedit is possible to create a Windows Active Directory group of users which I can use to permit access through the ASA (5520) firewall? I only can find vpn authentication with Radius but nog specific information about granting AD groups internet access via the ASA.
View 1 Replies View Relatedit is possible to create a Windows Active Directory group of users which I can use to permit access through the ASA (5520) firewall? I only can find vpn authentication with Radius but nog specific information about granting AD groups internet access via the ASA.
View 1 Replies View RelatedWe have an RVS-4000 router that we use as an Internet gateway on our school network. I am trying to set up an Internet Access Policy to block some specific websites by URL using a domain name. I set up the policy, and added a PC to the list using the mac address, and the blocking did not work. I went back to the list and added the IP address of the same PC, the policy still did not work to block the domain. I rebooted the router, cleared the Internet Temporary files and history on the PC, and the policy still does not work. It acts like it is going to block access to the website because it takes a long time, but it will eventually connect.
View 7 Replies View RelatedI bought an rv120w. Now i want to trunk 2 lan ports to an smart switch to get 200MB out of that link.
The trunk mode in there in the manual that came in the cd with the unit i bought but is not in the web console.
I have updated the IOS to 1.0.3.10 to see if th trunk mode was there but is not.
My question is,
1 is that trunking feature there in the ios?
2- If not, why is listed in hte manual that came with the unit?
3- if it is in the ios, is there a was to by pass the web console and configure this?
4- can i do i maybe backing up the config then, editing the file and restoring it?
Screenshot below is from the manual in hte cd that came with the router
I want to setup Wireless Clients MAC+Active Directory based acess on AP 1242 standalone Wireless series.Steps i have configured :
1) SSID manger under Open authentication : Selected with EAP.
2) under advacned Radius.MAC Address AuthenticationMAC Addresses Authenticated by: Authentication Server Only
3) Server Manger : Current server list added the radius ip address 10.1.200.x
I have a pair of ASA 5520s operating in failover pair as active/standby, having two contexts on them. I am planning to share the load and make it active/active making first context active on the primary unit and second context active on the secondary unit. My question is if this will disrupt any connectivity thru these firewalls when I do "no failover" on the active/standby and assign the contexts to different failover groups and enable the failover back.
View 6 Replies View RelatedI have a dir-825 and wireless clients connected on the 5ghz ssid can see clients on 2.4 ssid and also out to the WAN (internet) but can't see any clients (my NAS ) connected to the dir-825 wired lan.2.4 ghz clients see everything fine. same with clients connected through the wired lan. I've tried DHCP and static ips. no idea what to do next.I was originally on 2.02 fw and have tried 2.03, 2.05 and now 2.06I'd really like to keep the 5ghz on because I have an AP by my tv and several devices connect from there to stream from the NAS.
View 2 Replies View RelatedHow come my 2.4GHz client can't see my 5GHz client? Shouldn't they be visible through the DIR-825 router?
View 1 Replies View RelatedI purchased the Dir-655 yesterday. My home network was all gigabit except for my router which was working fine, but I wanted the whole network within my house to be at gigabit speed. I move a lot of big files around to my network storage device and wanted to speed that process up, which it has.After streaming a movie through the router out a hard wired port to my PC when I finished that movie I noticed that no other path through the router would work including Wi-FI, till I rebooted then they all worked again.
Last night watched a movie through the Wi-fi channel to my media PC in the basement and when the movie finished, no other port on the router worked until a reboot.In each case the channel/path in use continued to work although other paths were not working.It seems like a firmware/ buffer management issue.I made a couple changes. Enabled the Multicast option and turned of QOS.Failed again but not under the same conditions as before so I just turned off the Defragmentation option, I forget exactly how it was labeled.
I am looking at deploying a pair of 5585X's in an active/active multiple context state. I am creating Mulitple contexts that need to be able to route to each other. I was going to deploy a type of Gateway context that has a shared interface to all of the other contexts, instead of sharing interfaces directly between the contexts, i beleive this will work as basically i am just cascadng the contexts and sharing interfaces.
The main problem i have come across, is that if i deploy active/active across two appliances using 2 failover groups i can not see a way to route between them, for example.
I have Context 1, Context 2 and Context GW A including the shared interfaces of Con1 and Con2 in failover group 1 on appliance A with the respective standbys on Appliance 2. I have Context 2, Context 4 and Context GW B including the shared interfaces of Con 3 and Con 4 in failover group 2 on appliance B with the respective standbys on Appliance 1.
I need to be able to route traffic between Context GW A and GW B so that the contexts can communicate in normal operation and in failover. I do not beleive that I can share an interface between contexts in two separate failover groups and to be honest without adding a L3 device between the appliances i am not sure if this is possible.
I have two ASA 5510s running in Active/Active mode. I need to make config changes on them. How do I go about it? Do I power off the secondary ASA and make the config changes on the primary and then power on the secondary ASA ? Or this another way to do this?
View 3 Replies View RelatedI have an ASA5520 in location A with an ISP connection and a matching ASA5520 in location B with a separate ISP connection. We have fiber connecting the two locations and vlans passing back and forth so I will be able to configure the failover via a vlan as well as extend the ISP's to each location via vlans. The Active/Active configuration with the multiple security contexts does not seem to be an issue but how is a redundant ISP configured in this mode?We want to have context A using the ASA in location A with ISP1 as the primary and failing over to ISP 2 in locaiton B We also want to have context B using the ASA in location B with ISP 2 as the primary and failing over to ISP1 in location A Would route tracking provide the desired result? Is there a better option?
View 1 Replies View RelatedThe 6509 Series Switches support the scenario VSS Active-Active Chassis, I would like to setup both switch's as one virtual switch but working at the same time, not with Active - Stand By Chassis.
My plans it to create PortChannel accross both Switches 6509 in order to have 2 links one connected to one slot/switch and the other connected to slot/switch in the second 6509 for servers redundancy.
I am working on a network which has two ISP connections (Active/Active) terminating on router (ASR1000). From the LAN side (6500 switch) all the traffic need to be route on ISP1 but some of the specific subnets like 10.250.0.0/16 need to be route on ISP2 connection.
I am planning to use PBR and NAT with route maps. any documents or refrences are provided.
(access switches)---------(core switch)----------(routers)----------------(ISP1)
----------------------(ISP2)
I faced one problem in our core switch 4507 R . Active sup lost connection and standby came active. We got lot of errors/alerts on console shown below. [Code] Also when I reloaded the switch with reload command only both sups got reloaded but I want to reload all the modules but reload command do not gives any options for that.
View 2 Replies View RelatedI have 2 asa 5520 firewalls including and 1 AIP-SSM-10 module in each of them. the configuration is set using active/active failover and context mode.
Both of them run individualy the IPS module. The IPS is configured using inline mode and fail-open option. However when one of the module fails and the state is changing from up to init or anything else making the IPS to fail then failover is detected and ASA consider it as failover and bounce context to the other unit.
IPS soft is 6.0(4) and ASA soft is 8.0(3)
I have checked cisco doc and it is confusing to me. it says: "The AIP-SSM does not participate in stateful failover if stateful failover is configured on the ASA failover pair." but it really does participate. Running is not really an option because of production network impact matter..
We have an Active/Active ASA 5520 setup, as i know in Active/Active setup there is no remote VPN access, So i could overcome this limitations?I have a solution but i dont know if it is ablecable or not? we have a spare ASA 5510, so i can use it behind Active/Active Firewalls and assign a public static NAT IP address to it and open all IPSEC and VPN ports and let the remote users to connect to it, is this ablecable setup or not?
View 1 Replies View Relatedits possible to set up active/active failover using etherchannel on 5585s?
View 1 Replies View RelatedHow to Configure ASA5520 for Active/Active
View 8 Replies View Relatedour application team is mandating, that the solution we should come up with for SLB, should support Active/Active mode of SLB operation.
My question, is this mode of operation supported/accredited by Cisco, and what is the draw back from the traditional active/standby.
I have had trouble with my DIR-651 router since i bought it. To put it simply, if there a device connected to the wireless network, no other device can connect. Here are the devices i have:
hp pavilion running fedora 15
hp touchpad (webos)
htc thunderbolt (android)
dell inspiron (? work computer..not here right now) running windows xp
I am running wpa 2 using AES encryption in wireless mixed b/g/n mode (I have tried all other permutations of BGN. On the devices that will let me see error logs, all i get is "authentication invalid" errors.) In a few rare cases, i am able to get a second device connected by disabling the first device, connecting second, and reconnecting first.I am running the newest firmware 1.10NA.
When I go into the Network Settings, and the end of the page I find a list named "Number of Dynamic DHCP clients: 7". As far as I know, I should only see 4, all 4 laptops; however, I see 2 UNKNOWN entries in this list, and one name "Macondo". Each of these entries have an option (a link) saying "Revoke" and other "Reserve". I am just wonder if these entries are intruders in my home network. What should I do? I am afraid to break my internet connection. By the way, I set up every single one of my family 4 laptops at home with a WPA-PSK using a very long key.
View 9 Replies View RelatedI have a TP-Link TD-W8960N Wireless Router. I would like to know what the I.P. addresses of connected clients are (both those connected wirelessly & those connected by Ethernet cable). There are about 6 computers in my network, some have dynamic and others have static I.P. addresses.I am finding it difficult to navigate the router,on which menus get me to the information that I am interested in
View 1 Replies View RelatedI've just discovered this thing in Windows Event log. The DHCP-Client log is full with this: the client received a NAK from the DHCP Server. Strangely, they still get the desired IP address. (Which are reserved adresses for the MAC adresses.)So I've looked at the logs in the DIR-615 (rev.D, FW: 4.13), and found this:
View 1 Replies View RelatedI have 2 RV042 routers. As of yesterday, for over 2 months, quick vpn has not been functioning. I had a 2008 server installed; the tech could not get the quickvpn clients to the server, so his solution to give clients access was to map the server to the internet. As you can imagine, it has been attacked consistently and we have since removed the server. Clients have not been able to use Linksys quickvpn client to connect. I have had 3 different network technicians, and have been charged way too much for nothing, and the best i got was it being restored to its broken state. We thought it was a flakey router, but both do the same thing.
View 7 Replies View RelatedWe are a small business with about 9 Macbook pros and 3 PC's connected wirelessly to the router. The Mac-computers sometimes lose their wifi-connection to the router. When this happens they have to select the wifi network again from the menu, to reestablish their internet connection. For some of the clients, this happens about once each day and for others multiple times a day. The problem doesn't seem to appear on the PC's.
I have tried to solve the problem by making DHCP reservations for each computers MAC-address, but with no luck. I also tried to set the 802.11 Mode to 'Mixed 802.11n and 802.11g', and turning WISH off. I read that the connection can be disturbed, if other wifi-networks in the area uses the same channel, so I changed it to channel 3, based on a scan of the network, where 3 appeared to be the least used. The WPA Mode is set to 'WPA-2 Only' and Cipher type is 'TKIP and AES'
The Dir-655 is hardware version B1 and the firmware is 2.0.
There were 6 computers on the 2.4GHz band, and 2 on the 5GHz.Everytime the people on the 2.4GHz band would get disconnected for no reason, but this router should be able to handle that number easily. After lots of fiddling, like telling people to shut down their phones WiFi, I finally found the culprit:
N and G mixed mode
Even with only Wireless-N devices there would be problems. N-only mode worked well.That is unpractical for me as there are some devices here that are still on Wireless-G, like game consoles and some phones.