Cisco Routers :: RV082 Fails To Respond Until Manual Restart
Nov 3, 2012
I've been noticing that occasionally our 2nd Gen RV082 fails to allow internal admin management until a manual restart. After the restart, all seems to be fine and traffic/router is very responsive. The following describes typically how the issue occurs: Internet traffic is rather slow and unresponsiveContent is failing to load for end usersWebsite are loading but with images or css failing to loadWebsites fail to load and appear offline (not all, but some such as ebay for example)We recognize there is a problem, let's try to access the local router adminFails to load the log-in prompt, so we manually reboot the deviceAll is operational for now We are running Firmware Version: 2.0.0.19-tm. [URL]
View 2 Replies
ADVERTISEMENT
Jun 9, 2013
We have a RV082 V03 being used as a gateway that was bought in mid 2011. The firmware version that came with it was v4.0.0.07. Up until we upgraded to firmware v4.2.1.02(Upgraded in Jan.2013), we would have to restart the router once every month due to loss of internet connectvity and it locking up. After I upgraded it to the 4.2.1.02, it gradually starting increasing from rebooting the router once a month, to once a week, then to multiple times a day. Today, I upgraded the firmware to the latest version being v4.2.2.08 and it has not froze up since the upgrade, but then again, it happens randomly through the day so it might not happen until tomorrow morning so we will see how this goes. During the time when it looses connectivity, I CANNOT get to the web gui or even ping the RV082 device. The lights on the RV082 are blinking like it is working though.This router is not even 2 years old yet and cannot believe that it would be dying already.
View 3 Replies
View Related
Sep 4, 2011
I have a rv082 small business router and the current firmware will not apply. I downloaded the v4.04 firmware update and tried to apply it yet the update does not seem to work. I have downloaded it a second time and used the UPDATE FIRMWARE button to load and apply but no change.
View 1 Replies
View Related
Oct 27, 2011
I'm using a RV082 with latest firmware v4.0.4.02tm in one of our branch offices. Sometimes the tunnel to the main office (IPCOP 1.4.21) fails.
Both sides display the status "tunnel connected" but IP traffic doesn't go through. If i try to ping the main office using the RV082 diagnostic feature, the RV082 seems to run into a loop...the window continues refreshing without any error message and i'm not able to cancel the test. If I restart the RV082 using the web interface, the "diagnose" and VPN problem still exists, even if the web interface told me that the device did a restart.
The only solution is to to a cold restart of the RV082. After that, the VPN tunnel works again....
This problem occurred 3 times in the last 3 weeks. I never hat this problem with previous firmware versions at this ot other sites.
View 1 Replies
View Related
Dec 22, 2011
I am having issue with a RV082 with firmware:
v4.1.0.02-tm (Sep 16 2011 18:40:48)
On setup 1 I have;Using 2 WAN, 1 from fiber 5mbps symetric fixed public IP and other is DSL private dynamic dhcp address 3mbps/900kbps
On setup 2 i have:Using 1 WAN, from fiber 5mbps symetric fixed public ip Both router have exact same firewall configuration, subnet and port forwarding and we have the seccont backup DSL coming in a few day for setup 2.on both setup, the RV082 is the main internet gateway/firewall for a set of server...
Setup 1 work perfectly and been online for 2 week (since install) without issue
Setup 2 worked for 2 day then had to reboot, then work for few days then need reboot, now it look like it need to be rebooted every day. the internet just stop working and a simple reboot does the trick... also, when that happen I can stil remote in server that have port forwarded in the router or connect to router management port, but internet on the server is down... I tried opendns and google dns on both WAN connection and still no luck.I have followed instruction on various support forum;
-more reliable dns server
-lower MTU
-failover vs load balance
-disabling SPI and DoS protection
at this point I'm about to swap both router to see if it not a defective hardware or disconnect DSL WAN on setup 1 to see if its more stable but the whole point of installing this router was for Internet redundancy which so far dosent work as expected.
View 2 Replies
View Related
Mar 31, 2013
Cold start it will not connect to internet but the other computers I have do so I know it's not an internet connection issue.
Network Diagnosis fails to find anything nor does it make an internet connection. I only seem to make a connection on restart.
Win 7 64bit
View 1 Replies
View Related
Oct 23, 2012
I hope an easy question, in the WAN profile of our SA540 I have IP Aliases configured for a block of IP addresses we have. The active 2 IP addresses plugged into the actual RoadRunner modem respond fine to ping, the other three I have programmed to the WAN interface are not responding as I would think they should. Have I overlooked something? The "Block IP on WAN Interface" is disabled and pings back fine.
View 3 Replies
View Related
Jul 19, 2011
I just got digital cable, phone and internet and when I try to use the digital phone and internet at the same time, the internet wouldn't work. Its connected through Netgear N300. The wireless connection will not stay connected.
View 1 Replies
View Related
May 8, 2013
WRVS4400N needs to be manually connected when the power is recycled after power failure. Is there a setting to connect an IPSEC VPN automatically, instead of manually going in to connect the VPN
View 3 Replies
View Related
May 30, 2012
I bought an rv120w. Now i want to trunk 2 lan ports to an smart switch to get 200MB out of that link.
The trunk mode in there in the manual that came in the cd with the unit i bought but is not in the web console.
I have updated the IOS to 1.0.3.10 to see if th trunk mode was there but is not.
My question is,
1 is that trunking feature there in the ios?
2- If not, why is listed in hte manual that came with the unit?
3- if it is in the ios, is there a was to by pass the web console and configure this?
4- can i do i maybe backing up the config then, editing the file and restoring it?
Screenshot below is from the manual in hte cd that came with the router
View 2 Replies
View Related
Jul 4, 2011
I just installed a new RV042 v3 and updated the f/w to 4.0.3.03tm. While trying to sort out logging issues, I've tried a few times to restart the router via System Mgmt -> Restart -> Restart Router. When I do this I get the expected results -- I'm prompted to wait, and then to login again. But the System Up Time isn't reset to zero, and the log shows no sign of the router restarting.
Why doesn't this work? Is there some other way to remotely force a restart?
View 7 Replies
View Related
Feb 15, 2013
Manual and firmware not available for my f7d2401nt. The US support page do not find the model, the italian support page find the model but link to the US page ! Someone has at least the manual (englis, french or italian language) ?
View 2 Replies
View Related
May 20, 2013
N600 DB on OSX. I keep on reading the material that there is a link on the dashboard that I click on to set up the router manually. Nowhere on the dash board is that link. Where is that link?
View 1 Replies
View Related
Dec 16, 2012
I have two RV180W's which are excellent units in almost all respects. The one really noticeable problem is that when I have a power outage (which I have quite a lot in rural France) my RV180W does not automatically restart when the power is restored. Is it not possible to fix this in the next firmware upgrade, or have I missed something in the router menu/setup which I should have set.....?
View 1 Replies
View Related
May 12, 2011
I have a motorola usb modem which is connected to my laptop and i have shared the connection and have an ethernet cable from laptop to wireless modem (TP-LINK) such that other wifi enabled devices can connect to it.Now we have electricity blackouts and when that happens my wireless router gets turned off. Internet on the laptop is working fine, now when the electricity comes back and the wireless router is on, the net does not work on the other wifi devices and only my laptop (as its directly connected to the modem).I have to reboot my laptop for the shared connection to work.
View 2 Replies
View Related
Nov 27, 2012
I have recently purchased a RVS4000 router and am experiencing major downtime.Almost everyday the RVS4000 router losing internet connectivity. I noticed that when this happens I cannot login into the router from my pc which is connected to the RVS4000 network.The only way to restore connectivity is to restart the RVS4000 by disconnecting power and powering back up.The router's WAN is connected to my Cable modem.The RVS400 has two PC connected to it. (port 3 & 4) I have a Cisco 8-port switch connect to the RVS4000 with 3 additional PCs/devices on it.
View 6 Replies
View Related
Aug 7, 2012
We're getting the following message in the logs when we ry to connect: encrypted Informational Exchange message is invalid because it is for incomplete ISAKMP SA
One of the router is a V2 and the other is a V4 if that makes any difference.
View 12 Replies
View Related
Jan 29, 2013
We have an RV082 setup with WAN to the internet and LAN IP of 192.168.188.1.If I add a static route like so:
network: 192.168.166.0
mask: 255.255.255.0
gateway: 192.168.188.2
hop count: 1
interface: LAN
The device with IP 192.168.188.2 will be connected directly to one of the LAN ports on the router.Will that work to route, trying to get to 192.168.166.0 to the IP of 192.168.188.2?It just seems odd because the packets would hit the router then go back out through the LAN port.
View 4 Replies
View Related
Nov 17, 2011
isco epc3925 in transparent bridge provided by isp with following wan details
ip=x.x.x.120 subnet=255.255.255.248 gw=x.x.x.121 and 2 dns server ip's
I can't get the one-to-one nat working. read in some forums that the rv082 can do the job.
View 4 Replies
View Related
May 9, 2013
I have a Meraki Firewall that sits behind my Cisco RV082. The Meraki is setup to run a VPN connection with my server but I am having problems passing the VPN traffic through properly.
I have 2 Uverse Internet Connections that the RV082 using load balancing so that they are shared. I have 10 static IP's.
I am trying to come in on one of my static IP addresses throught the Cisco RV082 to the Meraki and after doing a capture on the meraki it appears that it is starting to receive data to intiate the VPN connection but when it sends data back to the VPN client machine it never makes it.
View 1 Replies
View Related
Nov 12, 2012
I have reset my RV082 router (both wit the reset switch and the factory default wizard) and run the setup wizard but regardless I can't connect to shaw.ca which is my service provider. I notice that if I use http://192.168.1.1 the browsers (IE & FF) default to https://192.168.1.1 and then I am prompted for a certificate. I can enter if I ignore the request but after getting in I simply cannot connect to my ISP.
View 4 Replies
View Related
Jan 12, 2012
Is it possbile to NAT to other subnets with the RV082. It is on a 192.168.41.x and I have a phone system on a 192.168.20.x. After searching all over others are saying no.
View 4 Replies
View Related
Jan 14, 2013
I just set up a new Linksys/Cisco RV082 router with the intent to get VPN working from outside the building. I have gone through the setup and while everything looks good, I have not been able to connect yet. I have tried everything that I know how, and am now hoping to get the answer from some pros.
Here's my setup. We use Comcast Business class internet. The modem is plugged into WAN port 1 on the RV082. I'm using the router as a DHCP server, that is working fine. My local subnet is 192.168.0.0/220
Right now all I want is to be able to log in as a client using QuickVPN. I set up one user and a client to VPN tunnel using the router's config page. Here's the settings I have:
Tunnel Interface is setup on WAN1, checkbox is enabled.
Local Group Setup
Local Security Gatewaytpe: IP Only
Local Security Group Type: Subnet
[Code]....
It seems like something is blocking the connection, but seeing that I have tried this after disabling the firewall completely it doesn't make sense to me. I also went into the config page for the modem and set up the router as a DMZ. I have also tried connecting with the client built into Windows 7, but that doesn't work either, I just get "connection failed with error 619"
I have the port in QuickVPN set to auto, but have tried both 443 and 60443 with same results.
I ran a port scan at [URL] and it shows I have 3 ports open...80,443, and 1723
View 4 Replies
View Related
Jan 24, 2012
I have a VPN tunnel from one RV082 to another, first router has IP range of 192.168.1.0 and the second one has range of 18.18.18.0, the connection works fine, here is where the issue starts, I am at a PC in the 18.18.18.0 network and I ping an IP in the other one e.g. 192.168.1.50 and it pings fine, but when I try to RDP into it or do anything to it I get no response, is it a firewall issue? Is it a NAT issue? I am at a loss, now that IP i mentioned does have RDP enabled and working because it is being port fowarded in the 192.168.1.0 router and I can access it through the public IP.
Also a workstation with a static IP 192.168.1.18 I can ping it if im in the local network but if I am in the remote one I cannot at all.
View 7 Replies
View Related
Jul 28, 2010
we have an RV082 router that a few days ago started restarting itself after normal usage.The simpton is that when people come to office, starting using the Internet the RV082 resets. It stays online for 3 to 12 minutes and then it resets again.
clicking on Reset to Factory Default in the web interfaceafter the reset, I confirmed that it was reset to factory default I reset it again using the reset buttomre-configure the RV082 manually.I also tested with another identical rv082 (hw version and firmware version) and after doing a backup of the config of the original rv082 and restoring it in the new rv082, the same problem happends.
View 20 Replies
View Related
Mar 15, 2013
I have an RV082 10/100 8-Port VPN Router and have configured the NAT table to allow for remote users, however I've run into an issue. It seems like there is a limited number of entries that you can put in the table,10, and I need to configure about 5 more IPs. Any way to expand the NAT table, or alternatively recommend a different router. I would also be willing to add another router to the network, but I have little experience doing that.
View 3 Replies
View Related
Jul 18, 2012
Are the RV042 and RV082 routers SIP AWARE?I haven't had any luck finding documentation stating such.
View 2 Replies
View Related
Oct 20, 2011
Just purchased a RV082 and once I switched a bunch of users over to it I can no longer access the web admin section. I have tried using both IE and Firefox and have used multiple workstations. I get to the login screen but it doesn't get any further. I am running the latest firmware v4.0.4.2-tm. It works for a while then just stops. The only fix is to turn off the device and back on and then it starts working again.
I've seen this issue on other small business cisco devices and had to stop using this because of this issue and switch to a higher grade cisco product but was hoping that this particular issue would have been resolved now across cisco's products.
View 7 Replies
View Related
Jan 9, 2012
I just migrated our office network router to a RV082. While configuring it, I came across three problems:
(1) From our ISP we have four public IP addresses which I want to make use of for outbound traffic. With the previous router we used we could configure LAN IPs(ranges) to map to static public IPs. Does RV082 support this? I could not find an option for that at the web-interface. From what I understand the 1-1 NATing only goes both incoming and outgoign ways and actually is 1-1 and not the many-to-one I am looking for.
(2) How is it possible to configure incoming port forwards to use a specific WAN interface? Will it always be the primary WAN interface?
(3) Does the telnet access provide more configuration options? I could not log in to it with the same user credentials as with the web-interface.
Serial Number : NKS1532xxxxFirmware Version : v4.0.4.02-tm (Jul 4 2011 13:30:56)PID VID : RV082 V03Firmware MD5 Checksum : 1f84d8d0a2a8b99f9bfa4409e64547aaLANWorking Mode : Gateway
View 0 Replies
View Related
Apr 27, 2013
we have a RV082 and have the DMZ option enable for a range of IPs within the same subnet of WAN IP and this works great. I have another range of Public IPs from our ISP that is not in the same subnet of the WAN IP and do not see a way on the RV082 to include this 2nd bank of Public IPs in the DMZ. Our ISP internet feed plugs into the RV082 WAN port and we have a switch pulgged into the DMZ port of the RV082 that is used to connect the public devices in the current DMZ. Both banks of Public IPs from our ISP come over via the ISP internet feed plugged into the WAN Port. My question is, if I cannot configure a DMZ rule to allow this 2nd range of Public IPs to "travel" to the RV082 DMZ port.
View 0 Replies
View Related
Nov 12, 2012
I would like to set the subnet mask off the lan to 255.255.240.0 but the selection menu do not allow to do it.
View 8 Replies
View Related
Sep 25, 2012
I wanted to know if you can connect a Cable modem to a SA520W, then connect a RV082 to the SA520W?
View 5 Replies
View Related
Mar 24, 2013
We recently moved our network over to RV082 router and its working great, well now we want to take advantage of VPN for our sales staff.
I was able to setup the VPN and using a PC at a remote office I can launch the quick connect and it connects right away, RV0 even shows the user connected. However the user cannot ping anything on our network via name or IP, connect to any resources, etc...
My understanding was when the client VPN would connect the user would get an IP from DHCP (this is on our Server 2008 DC) and they would be using that address, but when I run IPCONFIG on the client PC they just have there standard IP from remote office.
View 8 Replies
View Related
