Cisco Routers :: RV110W QuickVPN Doesn't Work
Mar 10, 2013
I have a problem with my RV110W router. I would like to setup Quick VPN access. Manual is quite straightforward: enable management, create users, install client and that's all, should be working. But NOT. it does not work.
Remote Management is enabled on port 8080. Should it be changed to 443 as required for QVPN? Or it does not matter. Is it ok, to have management on 8080 and QVPN on 443?
I have tried to connect via QVPN Client ver. 1.4.1.2. Of course ip as well as user and pass has been changed. I tried to change management port to 443, but first:
1. i was not able to access management console at all
2. QVPN - still did not work
View 4 Replies
ADVERTISEMENT
Dec 19, 2011
After a day of troubleshooting I have finally got the QuickVPN client to work. I connect however during the connection I get: "Server's certificate doesn't exist on your local computer. Do you want to quit this connection?" I click no and it connects fine other than this error. So how do I get rid of this error? Also I have exported the client certificate from the RV110 and put it in the quickvpn directory as I saw suggested elsewhere.
Here is my log:
2011/12/21 00:39:44 [STATUS]Connecting...
2011/12/21 00:39:44 [DEBUG]Input VPN Server Address = ***.***.***
2011/12/21 00:39:45 [STATUS]Connecting to remote gateway with IP address: **.**.**.***
2011/12/21 00:39:50 [WARNING]Server's certificate doesn't exist on your local computer.
2011/12/21 00:39:56 [STATUS]Remote gateway was reached by https ...
[code]....
View 2 Replies
View Related
Mar 15, 2013
I can backup the router settings on an RV110W, but not restore them. I get an "unable to write" error. (probably not the exact verbiage). Defective router, or firmware issue?
View 14 Replies
View Related
May 7, 2012
I bought a new WRVS400n recently because it had Gigabit speed, wireless n and a built in VPN server. The device works perfect except for the Quick VPN client. I'm a system engineer so I thought I could set it up quite easy just like any other device I configured in the past. Painfull but it isn't like this.
I set up the VPN on the WRVS4400n and generated a certificate. I saved both the client and admin certificate to my pc, I gave them a name to easily make up the difference between both of them. When placing the certificate in the installed QuickVPN folder, it doesn't seem to get recognised by the QuickVPN software. When I try to connect, it says 'Server's certificate doens't exist on your local computer'. I guess the naming convention must meet some kind of format, is that correct? If so, this should have been described in the documentation.
Besides that I checked if the required ports used by the VPN server are open on the public port of the device, that is the case. So It seems I'm quite close to get it working.
The version of QuickVPN I used is 1.4.2.1. The WRVS4400n has the latest firmware loaded.
View 1 Replies
View Related
Feb 25, 2012
I recently upgraded the firmware to 2.0.2.01-tm (from 2.0.0.19-tm). Now I noticed the RV082's local DNS server ("DNS Local Database" feature) does not work any more. Any URL-IPaddr combo I used to put in there was resolved prior to sending a request to the WAN's primary/secondary DNS server. It isn't a PC problem. I tested on different real and virtual machines, windows and Linux. Is there new "enable" switch somwhere?
View 3 Replies
View Related
Aug 6, 2011
I upgraded the firmware for my WRVS4400N v2 to version 2.0.2.1 firmware, now old and default passwords don't work. I have tried resetting it as well, and the default password does not work.
View 1 Replies
View Related
Jul 26, 2011
I have created a VPN client account on my RVS4000 router. I have installed Quick VPN on my laptop in the default directory -- Program Files (x86) / Cisco Small Business / Quick VPN Client
I have generated and exported a certificate -- RVS4000_Client.pem -- and placed that in the Program Files (x86) / Cisco Small Business / Quick VPN Client directory. When I attempt to connect using the Quick VPN client, I get the warning "Server's certificate doesn't exist on your local computer."
If I ignore the message I can log in, and ping resources inside the network and log into the router. However, I cannot mount any drives and the router shows that no VPN tunnels exist. I've read several posts here and elsewhere and can't seem to see where I've gone wrong.
View 1 Replies
View Related
Mar 5, 2011
I have a linksys wrt54gs wireless router (working fine since last 3 years) which connects to the internet fine if there is no password set. However if i set WEP password to protect the wireless connection, i am not able to connect to the wireless connection. Everytime i enter the passphrase, when trying to connect to the wireless network, it refuses to accept the password. I have tried this with 2 laptops (both running windows 7) and both have same issue.
View 2 Replies
View Related
Apr 13, 2013
I'm trying to get 'Access Control' working so I can limit Wi-Fi time on my kids iPod touches, but the settings aren't clear and the help file is not clear whatsoever.I've been testing it with my iPhone, I have the MAC added, but none of the options available will even stop my iPhone accessing the internet over my Wi-Fi.
View 1 Replies
View Related
Feb 2, 2013
I have a Belkin AC1200 Router. It seems working properly re Internet/Wireless connections. When I connect a printer (Canon Pixma MP500) through the USB port the (USB) light doesn't turn on, nor the printer is appearing on the "available devices" (Belkin USB Print and Storage Center).
View 2 Replies
View Related
Apr 2, 2012
what exactly is QuickVPN?Is it a IPSec VPN?Is it a PPTP?Is it a SSLVPN?can I resolve my local hostnames? That means, can I configure a lokal DNS Server?
View 3 Replies
View Related
Jun 13, 2012
let me know whether you can make the attached network using by RV110W or not.When I read the mannual of "rv110w_admin.pdf", P38, I guess RV110W cannot be built both NAT & Router mode.Because, I cannot setup NAT for internet access if I setup "Operating Mode" as "Router" on the setting of "Networking > Routing".And, I cannot setup the routing for internet access & MPLS-VPN access if I setup "Operating Mode" as "Gateway" on the setting of "Networking > Routing".
View 2 Replies
View Related
Aug 22, 2011
The PPTP client from Windows 7 is not working with this router; therefore I would like to try the quickvpn.Is there any paper from Cisco explaining how to setup the RV120W for quickvpn ?
View 1 Replies
View Related
Oct 21, 2011
So have a RV042 VPN router that is directly connected to the ethernet port of our comcast cable modem.
If I connect to it using QuickVPN (1.4.2.1) from a PC that is connected using AT&T 3G Network it works fine!
If I connect to it using QuickVPN (1.4.2.1) from a different PC that is connected using home WiFi (linksys wrtxxx) then it fails. In the VPN log all I see is failure messages for ping.
2011/10/22 15:47:28 [WARNING]Failed to ping remote VPN Router!
If I open a regular command prompt and attempt to ping the VPN router it works so not understanding why the QuickVPN is unable to ping.
how I can troubleshoot this further. Makes me think the RV042 config is fine otherwise it would not work on a 3G connection. Something on the home PC or the home network. Not sure what to check.
View 2 Replies
View Related
Mar 11, 2012
I've one RV042. I've configured VPN PPTP and it work (I've redirect port 1723 on router1 to rv042). If I can try to use quickVpn, client login and receive error "remote gateway is not responding". I have redirect port 60443 from router1 to rv042. Connection it's this: INTERNET-router1-RV042.
View 3 Replies
View Related
Oct 29, 2011
I have been battling with my Cisco RV120W router and QuickVPN.Running Windows 7 Home PremiumPerformed a fresh install to factory out-of-box install for WindowsRemoved NortonDid NOT perform any windows updatesInstalled QuickVN version 1.2.4.1I have updated the firmware to the latest version (confirmed by cisco)I can connet to the router and have a stable connectionI can ping both the router IP and the shared file server IPWhen I enter the shared file server IP into the search field (e.g. \192.168.100.199) and press enter, I see a connection to "share", so I click on this and then see "FolderName" of my shared files. I click on this folder and I get a timed out error.When I enter the routers IP address into a browser (IE8 as factory installed) I get a timed out error also.In the past, I have installed all important and recommended updates for Windows and still get the same scenerioI have called cisco support and went through router settings, assigned them a VPN username, they log in and can access the files without issue (What the @#$$@#$)Cisco support spent plenty of time with me, but since they could access my network and since I could ping my devices, they had no other suggestions further.
I have this fresh factor out-of-box install. I know this is most likely something to do with my laptop that I am trying to use to connect to the network. I have Frontier as my ISP for home. I don't know if there is anything they are doing to interfere with my connection. I have tried to connect to the network via ComCast as well, with no luck.tell me if there is something I need to tweak in my Windows 7 settings?
View 11 Replies
View Related
Dec 11, 2011
I've deployed a WRVS4400N router at one of my clients, however I'm unable to access resources on his network via DNS. I was hoping to use the router for DNS resolution, however when I connect via VPN, I can only connect to shares via IP address.
View 1 Replies
View Related
Mar 6, 2012
I have a Cisco RV120W connected to the internet. I have configured a QuickVPN user on the router, but I cannot connect via QuickVPN no matter on what PC I try (with firewall or without firewal, Windows XP, 7, ...). On the router it says the VPN user is connected, but on the client PC I receive remote gateway not responding. In the logs it says failed to ping remote VPN router. I tried changing all settings I could find on this forum, but the result stays the same (changed port to 60443, deleted all IKE and VPN policies, allowed ping, disabled fragmented packets etc...). None of all the settings seems to get any result.
View 11 Replies
View Related
Oct 6, 2011
I got a RSV4000 router here with the latest firmware 1.3.3.5, trying to get the quick VPN client to connect.As far configurations go I have under WAN set the IP, subnetmask, DNS1, DNS2 and gateway. And under VPN I have created a client account with a password, created and then exported the Cert to my client PC.But when I attempt to connect, the QuickVPN software hangs for a few moments at "Connecting" and then fails; when the general error.I'm running this on Windows 7 x64.
View 1 Replies
View Related
Sep 21, 2011
Today I purchased a RV042 wired router. I set the VPN connection but when I try to login using QuickVPN, get stucks in "Verifying network". I checked the logs:
2011/09/22 20:43:45 [STATUS]OS Version: Windows 7
2011/09/22 20:43:45 [STATUS]Windows Firewall Domain Profile Settings: ON
2011/09/22 20:43:45 [STATUS]Windows Firewall Private Profile Settings: OFF
[Code]...
From my side Im connected to a WRT54G2. VPN Passthrough enabled. Windows 7 Pro x64. No 3rd party AV or firewall. Windows Firewall disabled, also tried enabling it.
From the RV042 side it has a Static IP Address configured. DHCP server enabled. HTTPS enabled. UPnP disabled. L2TP disabled.Firewall disabled. Block WAN Requests disabled.
View 6 Replies
View Related
Feb 13, 2012
Is it possible to set up an RV110W to limit access to only specified websites according to a schedule? I can block access to specific sites using the Internet Access Policy settings under Firewall, but I can't figure out a successful way to block access to all sites except those specified. I also tried establishing access rules but that did not work either.
View 4 Replies
View Related
Feb 16, 2012
After nothing but hassles with my Linksys WAG120N, I bought a Cisco RV110W. Yesterday, I tried setting it up with the Linksys being used only as a modem. I was unable to though because when I entered 192.168.1.1 into my browser as per the Cisco setup instructions, I was taken to the admin login for the Linksys. This seemed odd to me, because the Linksys was not connected to the PC at all. The connection setup was exactly as specified in the RV110W instructions: modem connected to dsl line, ethernet cable from modem (Linksys WAG120N) to the slot marked "WAN" on the RV110W, another ethernet cable from RV110W to my PC. Despite this, the admin page was for the linksys not the cisco.
Today, I exchanged the WAG120N for a Netgear DM111P, just a modem, not a router. Same setup configuration: modem connected to dsl line, ethernet cable from modem (NetgearDM111P) to the slot marked "WAN" on the RV110W, another ethernet cable from RV110W to my PC. Same result - type in 192.168.1.1 and get taken to the admin page for "Netgear DM111P" .
View 6 Replies
View Related
Apr 7, 2013
I make a vpn site-to-site IPSEC tunnel between 2 RV110W the above ,you will find the configuration
Site1
Site 2
always the same message
View 3 Replies
View Related
Feb 5, 2012
I'm having problems setting up VLANs on my RV110W Small Business Router. I have updated the firmware to the latest : 1.1.0.9 Here is my set up :
WAN settings :
IP : 192.168.1.252 / 255.255.255.0 - Gateway 192.168.1.254
VLAN1 (default) :
IP : 192.168.2.254 / 255.255.255.0
VLAN3 (test) :
IP : 192.168.16.254 / 255.255.255.0
Inter-VLAN routing option is checked.
Symptoms :
- The communication from VLAN1 to WAN is fine
- The communication from VLAN3 to VLAN1 is fine
- The communication from VLAN1 to VLAN3 is not working
My routing table is :Routing table Entry ListDestination LAN IPSubnet MaskGatewayInterface192.168.2.0255.255.255.0192.168.2.254LAN192.168.1.0255.255.255.0192.168.1.252WAN192.168.16.0255.255.255.00.0.0.0LAN0.0.0.00.0.0.0192.168.1.254WAN
As you can see, the gateway for VLAN3 is set to 0.0.0.0, which is wrong I believe. I don't know how to update that. I tried to add a a static route for the subnet, but the router did not let me do that.
View 1 Replies
View Related
Apr 17, 2013
I am trying to configure wake on lan for my desktop and I can't seem to get it. I have tried using single port forwarding under the firewall settings but it never works. The computer's BIOS has been configured to wake on lan and so have the Ethernet ports. I have an app for the iPad that i used to use ot send out a ping to my old router (E2500) setup that used to wake the computer just fine. But this new router (RV110w) does not work at all even with the same single port forwarding set up.
View 2 Replies
View Related
Mar 15, 2012
I've to setup RV110W router as a simple Wifi hotspot in a company network and this Wifi hotspot has to allow traffic to all internal LAN (very simple LAN with few workstation and one server) and also to Internet via our gateway. I know this product isn't really designed for that... but I've to do so. LAN is managed by Windows DHCP server and I've Internet acces through Firewall. I think I've to connect RV110W to the company LAN with the RV110W WAN interface. I want the Wifi IP address to be in the same IP range than the LAN to allow Wifi clients to access our internal server but RV110W doesn't accept this. Or do I've to ignore the WAN interface and deal with only the RV110W LAN interface?
View 1 Replies
View Related
Jan 26, 2012
I have a pptp server on my network and am trying to configure my new RV110W so that I can tunnel through to it from outside.
I believe I must do port forwarding for TCP on port 1723 to get those packets going to my PPTP server. PPTP also uses GRE and I don't see that as an option anyware in port forwarding... Does that just work... as a matter of the VPN pass through checkbox being enabled ?
My netgear router would lock up every few days but it under the firewall configuration it had list of services that included PPTP and I just selected that, entered the IP addresses on the outside that I would accept, and the IP address on the inside that the PPTP clients would connect to, and it worked....
I'm thinking it is harder on this device because this device supports actually logging into it.. I am interested in learning more about that technique especially if it is more secure but the way I see it the firewall device can see all of my network and the pptp server I am using is on a file server and limited to those files shared on that server.
View 3 Replies
View Related
Apr 2, 2012
With firmware 1.2.0.9 - can the RV110W be used as a VPN endpoint? The VPN capabilities have been expanded in this version - but from the docs this isn't quite clear to me.
View 3 Replies
View Related
Mar 31, 2012
I just bought and setup a RV110W. I noticed while scanning it from the WAN side that it always has port 443 open, even when remote management and VPN access are disabled. Why is this port still open, and how do I close it? Or is this a bug in the firmware? I am using firmware version 1.1.0.9, which is the most up-to-date for this unit. Having open ports allowing unsolicited contact from the WAN side, especially inadvertant ones, is a major security hole.
View 7 Replies
View Related
Dec 5, 2012
I have recently hit a brick wall with my router... Yesterday the router was acting funny rebooting about every 5 to 10 minutes. Didnt really think anything of it then it got annoying fast. So i checked my configs and nothing was out of normal checked my firmware and noticed it was out of date. So i grabbed the newest firmware 1.2.0.9 and uploaded it... uploaded fine and then rebooted as it should at that time the power flickered again because somone had plugged an large ac adapter over top of the power switch on the power bar and it was intermittently turning the power off when the table moved... the router then power cycled mid update and is now stuck at the blinking power light state and hasnt changed for 24 hours now...
View 1 Replies
View Related
Feb 3, 2013
I am thinking about buying one of the 2 routers i have listed above. I have some concerns though.
First off what are the MAJOR differences between the two? (they look the same to me)
Do they both contain PPTP and is it simple to configure? Do i need any kind of special client software? Can i use my iphone and ipad to connect to the vpn server. Is there a minium download/upload speed to have a vpn sever?
View 6 Replies
View Related
Jul 8, 2012
Regarding to the connection RV110W to any Cisco router, should I use a crossover cable accordingly? Because, I heard that the crossover function is done inside of some switches and routers. So, I would like to know whthether the function is included into RV110W.
View 3 Replies
View Related
Jun 4, 2012
Is there a way to configure the router through CLI (command line interface)In other Cisco devices we always were able to simply insert a configuration throught the CLI.Now it seems it can only be done with the Webbrowser.
View 7 Replies
View Related
